IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This reverts commit 43c6d5abac
(and a small part of 4046d8361c)
It turns out we don't actually need to set the global ip_forward setting.
The only relevant setting is the one on each interface.
What the global toggle actually does is switch forwarding on/off for all
currently present interfaces and change the default for new ones.
That means that by setting the global ip_forward we
- Introduce a race condition, because if the interface with IPForward=yes
is brought up after one with IPForward=no, both will have forwarding
enabled, because the global switch turns it on for all interfaces.
If the other interface comes up first networkd correctly sets forward=0
and it doesn't get overridden.
- Change the forwarding setting for interfaces that networkd is not
configured to touch, even if the user disabled forwarding via sysctl,
either globally or per-interface
As forwarding works fine without this, as long as all relevant interfacest
individually set IPForward=yes: just drop it
This means that non-networkd interfaces use the global default while
networkd interfaces default to off if IPForward isn't given.
Introduce BindCarrier= to indicate the set of links that determine if
the current link should be brought UP or DOWN.
[tomegun: add a bit to commit message]
For now we only support the hardcoded values RT_SCOPE_{UNIVERSE,LOCAL,HOST},
and not numerical values or values from /etc/iproute2/rt_scopes.
This addresses https://bugs.freedesktop.org/show_bug.cgi?id=88508.
This allows both IPv4 and IPv6 link-local addresses to be enabled or disabled. By default
we still enable IPv6LL and disable IPv4LL. The old config option is kept for backwards
compatibility, but removed from the documentation.
This introduces am AddressFamilyBoolean type that works more or less
like a booleaan, but can optionally turn on/off things for ipv4 and ipv6
independently. THis also ports the DHCP field over to it.
This adds two new settings to networkd's .network files:
IPForwarding=yes and IPMasquerade=yes. The former controls the
"forwarding" sysctl setting of the interface, thus controlling whether
IP forwarding shall be enabled on the specific interface. The latter
controls whether a firewall rule shall be installed that exposes traffic
coming from the interface as coming from the local host to all other
interfaces.
This also enables both options by default for container network
interfaces, thus making "systemd-nspawn --network-veth" have network
connectivity out of the box.
Let's stick to generic sections that describe the general technology,
instead of specific per-object sections, unless we really have a reason
to do that otherwise.
This patch add support to specify path cost of the
bridge port to be configured via conf file.
Exampe: conf
file: br.netdev
[NetDev]
Name=br-test
Kind=bridge
file: br.network
[Match]
Name=em1
[Network]
Bridge=br-test
[BridgePort]
Cost=332
bridge link
2: em1 state UP : <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 master
br-test state disabled priority 32 cost 332
This lets the routing metric for links to be specified per-network,
still defaulting to DHCP_ROUTE_METRIC (1024) if unspecified. Hopefully
this helps with multiple interfaces configured via DHCP.
This causes machines without connectivity to hang where they would otherwise fail. Keep it
opt-in for now, but consider whether we sholud just drop it.
This changes the behavior when both DHCPv4 and IPv4LL are enabled. Before,
we would disable IPv4LL when we got a DHCPv4 lease and enable it if the
lease was lost.
Now we just always set up both, if both are enabled, but the DHCPv4
addresses and routes will always take precedence due to their metric
and scope.
This is necessary for non-ipv4ll hosts to communicate with ipv4ll-only hosts on the same link. Defaults
to being enabled, but can be opted out.
See: <http://avahi.org/wiki/AvahiAutoipd#Routes>
It appears there is no good way to decide whether or not broadcasts should be enabled,
there is hardware that must have broadcast, and there are networks that only allow
unicast. So we give up and make this configurable.
By default, unicast is used, but if the kernel were to inform us abotu certain
interfaces requiring broadcast, we could change this to opt-in by default in
those cases.
Vendor Class Identifier be used by DHCP clients to identify
their vendor type and configuration. When using this option,
vendors can define their own specific identifier values, such
as to convey a particular hardware or operating system
configuration or other identifying information.
Vendor-specified DHCP options—features that let administrators assign
separate options to clients with similar configuration requirements.
For example, if DHCP-aware clients for example we want to separate
different gateway and option for different set of people
(dev/test/hr/finance) in a org or devices for example web/database
servers or let's say in a embedded device etc and require a different
default gateway or DNS server than the rest of clients.
Now route metric can be configuted via conf file:
example conf:
[Match]
Name=em1
[Route]
Gateway=192.168.1.12
Metric=10
Test:
ip route output
default via 192.168.1.12 dev em1 metric 10
[tomegun: squash TODO update and reword man page a bit]
Send hostname (option 12) in DISCOVER and REQUEST messages so the
DHCP server could use it to register with dynamic DNS and such.
To opt-out of this behaviour set SendHostname to false in [DHCP]
section of .network file
[tomegun: rebased, made sure a failing set_hostname is a noop and moved
config from DHCPv4 to DHCP]
This adds support for DHCP options 33 and 121: Static Route and
Classless Static Route. To enable this feature, set UseRoutes=true
in .network file. Returned routes are added to the routing table.
If there are v4 or v6 specific options we can keep those in separate sections,
but for the common options, we will use only one.
Moreovere only use DHCP=[yes/both|no/none|v4|v6] to enable or disable the clients.
