IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
By default the run_qemu() function enables KVM automatically
if it detects the /dev/kvm char device and if the machine is not
already a KVM one. Let's add a TEST_NO_KVM env variable to suppress
this detection.
Make the interactive debugging of (particularly QEMU) machines less
painful, by replacing the default vt220 TERM with linux one, and
by not shutting down the machine after running the test itself.
to reduce memory requirements for volume manipulation. Also,
to further improve the test performance, reduce number of PBKDF
iterations to 1000 (allowed minimum).
We'd install the service file, and then dbus-broker-launcher because it is
mentioned in ExecStart=, but not the main executable, so nothing would work.
Let's just install dbus-broker executables if found. They are small, so this
doesn't matter much, and is much easier than figuring the exact conditions
under which dbus-broker will be used instead of dbus-daemon.
Since systemd 206 the combination of systemd and mkinitcpio
causes, under certain conditions, the rootfs to be double fsck'd.
Symptoms:
```
:: performing fsck on '/dev/sda1'
systemd: clean, 3523/125488 files, 141738/501760 blocks
********************** WARNING **********************
* *
* The root device is not configured to be mounted *
* read-write! It may be fsck'd again later. *
* *
*****************************************************
<snip>
[ OK ] Started File System Check on Root Device
```
This occurs when neither 'ro' or 'rw', or only 'ro' is present
on the kernel command line. The solution is to mount the roofs
as read-write on the kernel command line, so systemd knows to not fsck
it again.
Previously, 'degraded' state is ambiguous for bonding or bridge master:
1. one or more slave interfaces does not have carrier,
2. no link local address is assigned to the master,
3. combination of the above two.
This makes the above case 1 and 3 are in the new 'degraded-carrier'
state, and makes 'degraded' state as all slaves are active but no
link local address on master.
When enabled, three samples are used to determine the value of a
received bit by majority rule.
This patch adds support for the TripleSampling= option in the [CAN]
section of .network files.
If the QEMU_SMP value has not been explicitly set, try to determine it
from the number of online CPUs using the nproc utility. If this approach
fails, fall back to the default value QEMU_SMP=1.
This change should significantly help when running integration tests
under QEMU on multicore systems.
This test exposes a race condition when running in LXC, see issue #11848
for details. Until that is understood and fixed, skip the test as it's
not a recent regression.
This avoids a warning:
An address '192.168.42.100' is specified without prefix length. The
behavior of parsing addresses without prefix length will be changed
in the future release. Please specify prefix length explicitly.
This test case is a bit silly, but it shows that our code is unprepared to
handle so many network servers, with quadratic complexity in various places.
I don't think there are any valid reasons to have hundres of NTP servers
configured, so let's just emit a warning and cut the list short.
https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=13354
- This test needs resolved, so make sure it is started. In some Debian
environments it is not.
- It was an unnecessary, and now failing assumption that name servers
get atomically written to the resolved's resolv.conf. Wait until both
expected name servers are in the file.
Since version 241 (commit ea4678?), querying MX type records for
single-label domains does not actually forward the query to the DNS
server any more. Use "example.com" instead, which is the recommended
test domain anyway.
dnsmasq 2.80 changed behaviour when being queried by resolved with
enabled DNSSEC: It returns errors for SOA and DS queries which cause the
entire query to fail. As we don't configure DNSSEC in this test anyway,
just disable it so that we retain compatibility with old and new dnsmasq
versions.
The test was failing in Ubuntu CI with a 30s timeout. It makes
sense to keep the file so exercise the set allocation logic, but
we can make it shorter.
We were already using OrderedSets in the manager object, but strvs in the
configuration parsing code. Using sets gives us better scaling when many
domains are used.
In oss-fuzz #13059 the attached reproducer takes approximately 30.5 s to be
parsed. Converting to sets makes this go down to 10s. This is not _vastly_
faster, but using sets seems like a nicer approach anyway. In particular, we
avoid the quadratic de-unification operation after each addition.
The original version of the test used netcat along with a standard
AF_UNIX socket, which caused issues across different netcat
implementations. The AF_UNIX socket was then replaced by a FIFO with a
simple echo, which, however, suffers from the same issue (some echo
implementations don't check if the write() was successful).
Let's revert back to the AF_UNIX socket, but replace netcat with socat,
which, hopefully, resolves the main issue.
Relevant commit: 9b45c2bf02
When there is bad link in the network the carrier goes up/down.
This makes networkd stops all the clients and drop config.
But if the remote router/dhcpserver running a prevention
of DHCP Starvation attack or DHCP Flood attack it does not allow
networkd to take a DHCP lease resulting failure in configuration.
This patch allows to keep the client running and keep the conf
also for this scenario.
Closes#9111
Currently /boot/initramfs-linux.img is used as the default initrd for ArchLinux.
Although, since the kernel modules that are not necessary for the host environment are removed from
initramfs-linux.img by mkinitcpio 's autodetect hook, the kernel modules necessary for qemu may be missing.
(ata_piix, ext4, and so on in my case.)
As a result, the test environment may not be built properly and the test will be failed.
initramfs-linux-fallback.img will skip this autodetect hook, so the test will run successfully in more
environments.
Both initramfs-linux.img and initramfs-linux-fallback.img are generated by default.
rescue.service pulls in /bin/plymouth, which doesn't exist on some
distributions (e.g. Arch Linux). Let's mark it as optional, as it's not
even required by the referencing unit and causes unwanted fails in the
integration testsuite.
The test is a bit messy because it must be done on a device that
enforces a tentative state for IPv6 addresses, and it appears
that the dummy device does not. So we use a bond instead.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Nitpicky, but we've used a lot of random spacings and names in the past,
but we're trying to be completely consistent on "cgroup vN" now.
Generated by `fd -0 | xargs -0 -n1 sed -ri --follow-symlinks 's/cgroups? ?v?([0-9])/cgroup v\1/gI'`.
I manually ignored places where it's not appropriate to replace (eg.
"cgroup2" fstype and in src/shared/linux).
Commit 250e9fadbc introduced
support for %j/%J specifier in unit files. The function
unit_name_printf is used in unit dependency resolution,
such as Wants / After directives, but was missing support
for the %j. Add to allow directives such as:
[Unit]
Wants=bar-%j.target
Fixes: systemd/systemd#11217
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Previously, we'd return DNS_SCOPE_MAYBE for all domain lookups matching
LLMNR or mDNS. Let's upgrade this to DNS_SCOPE_YES, to make the binding
stronger.
The effect of this is that even if "local" is defined as routing domain
on some iface, we'll still lookup domains in local via mDNS — if mDNS is
turned on. This should not be limiting, as people who don't want such
lookups should turn off mDNS altogether, as it is useless if nothing is
routed to it.
This also has the nice benefit that mDNS/LLMR continue to work if people
use "~." as routing domain on some interface.
Similar for LLMNR and single label names.
Similar also for the link local IPv4 and IPv6 reverse lookups.
Fixes: #10125
There seems to be no error per se. RequiresMountsFor=%s%s%s..%s%s%s is expanded to
RequiresMountsFor=/bin/zsh/bin/zsh/bin/zsh/bin/zsh/..., which takes a bit of time,
and then we iterate over this a few times, creating a hashmap with a hashmap
for each prefix of the path, each with one item pointing back to the original unit.
Takes about 0.8 s on my machine.
When using networkd we currently have no way of ensuring that static
neighbor entries are set when our link comes up. This change adds a new
section to the network definition that allows multiple static neighbors
to be set on a link.
Fixes the following error:
Failed to mount test /run: No such file or directory
By the time command "./test-udev check" calls function "fake_filesystems",
directory "test/run" must be present.
When there is a failure to setup the environment, the following happens:
1. Command "./test-udev check" exits with non-zero code.
2. Perl function "system" returns the code.
3. The code is evaluated as true by Perl.
Then we stop the test.
This provides us with an easy command line to test this script. Because
the test was so difficult to get running noone ever did, hence it broke
badly quickly. Let's fix that.
Previously, the test would use the existing static hostname. However,
this woud not work as expected in the static hostname was "localhost"
because the transient hostname will override the static one in that case
anyway, as the assumption hostnamed makes is that "localhost" is a
non-initialized hostname.
Hence when testing this, let's first set the static hostname to
something specific first (that is not "localhost").
Otherwise networkd isn't happy.
Let's also make addition of the "systemd-network" non-fatal. The user
exists on many machines anyway, hence it shouldn't fail if it already
exists.