IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Previously, AddMatch/RemoveMatch calls where processed exclusively in
the proxy. That's racy however, since subscribing to a signal might not
complete before the signal is sent due to some subsequent method call.
Hence, in order to expose the same ordering guarantees as dbus1 process
the AddMatch/RemoveMatch calls from the proxy, so that they are
dispatched synchronously to all following messages, thus fixing the
race.
Ultimately, we should probabably dissolve the driver entirely into the
proxy, as it is purely a compatibility feature anyway...
The way the kernel namespaces have been implemented breaks assumptions
udev made regarding uevent sequence numbers. Creating devices in a
namespace "steals" uevents and its sequence numbers from the host. It
confuses the "udevadmin settle" logic, which might block until util a
timeout is reached, even when no uevent is pending.
Remove any assumptions about sequence numbers and deprecate libudev's
API exposing these numbers; none of that can reliably be used anymore
when namespaces are involved.
In contrast to a filename-only argument, find_binary() did not
actually check if an path exists, allowing the code to fail later on.
This was OK, but it seems nicer to treat both paths identically.
Also take advantage of path_make_absolute_cwd doing strdup() by itself
if necessary to simplify.
If a persistent timer has no stamp file yet, it behaves just like a normal
timer until it runs for the first time. If the system is always shut down
while the timer is supposed to run, a stamp file is never created and
Peristent=true has no effect.
This patch fixes this by creating a stamp file with the current time
when the timer is first started.
- Negative/positive errno mixup caused duplicates not to be detected properly.
Now we get a warning about some duplicate entries in our own catalogs...
- Errors in update_catalog would be ignored, but they should not be.
greedy_realloc() and greedy_realloc0() now store the allocated
size as the count, not bytes.
Replace GREEDY_REALLOC uses with GREEDY_REALLOC_T everywhere,
and then rename GREEDY_REALLOC_T to GREEDY_REALLOC. It is just
too error-prone to have two slightly different macros which do the
same thing.
Usually RUNNING implies LOWER_UP, but for drivers that don't support oper state, RUNNING can
also mean that the state is unknown. In that case we should just trust LOWER_UP directly.
The interface is not fully ready until it enterns RUNNING. This was causing
problems with sending out DHCP messages before the interface was ready, so they
would get lost. In particular this affected DHCP INIT-REBOOT, as it relies on
the first package sent being successful (or it will fall back to a full reboot).
Also improve the logging a lot, to make future debugging of link state a lot
easier.
This error should never happen, so replace the check with an assert. The check
was anyway broken due to an uninitialized return value.
Reported by Thomas Hindoe Paaboel Andersen <phomes@gmail.com>.
Also reshuffle some code to make the correspondence with the RFC a bit more
obvious.
Small functional change: fail if we try to send a message from the wrong state.
Add an explicit stop state for IPv4LL so that the user can stop the
IPv4LL client from the callback. When returning from the callback,
check also the stop state in order to halt any further protocol
processing.
Similar to DHCP, the IPv4LL library user can decide to free the LL
client any time the callback is called. Guard against freeing the
LL client in the callback by introducing proper reference counting.
Also update code using the IPv4LL library to properly handle a
returned NULL from the notify and stop functions if the IPv4LL
client was freed.
Add an explicit stop state for the DHCP client so that the library
user can issue a stop at any time the callback has been called.
When returning from the callback, check also the stop state and
stop any further DHCP processing.
The DHCP library user can decide to free the DHCP client any time
the callback is called. After the callback has been called, other
computations may still be needed - the best example being a full
restart of the DHCP procedure in case of lease expiry.
Fix this by introducing proper reference counting. Properly handle
a returned NULL from the notify and stop functions if the DHCP
client was freed.
