IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Similar to the virtual ethernet driver veth, vxcan implements a
local CAN traffic tunnel between two virtual CAN network devices.
When creating a vxcan, two vxcan devices are created as pair
When one end receives the packet it appears on its pair and vice
versa. The vxcan can be used for cross namespace communication.
Now we don't support tunnels to be created without a .network file
that is we need a interface index.
This work allows tunnel to be created without a ifindex.
Closes#6695
this patch makes it possible to configure a vlan aware bridge without the
PVID. To configure no PVID set DefaultPVID=none in the [BridgeVLAN] section.
fixes#5716
This work adds support for setting the IPv6 flow label for vxlan.
vxlan.netdev
NetDev]
Description=vxlan-test
Name=vxlan1
Kind=vxlan
[VXLAN]
Id=33
Local=2405:204:920b:29ac:7e7a:91ff:fe6d:ffe2
Remote=FF02:0:0:0:0:0:1:9
FlowLabel=104
ip -d link show vxlan1
8: vxlan1: <BROADCAST,MULTICAST> mtu 1430 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether be:83:aa:db:6b:cb brd ff:ff:ff:ff:ff:ff promiscuity 0
vxlan id 33 group ff02::1:9 local 2405:204:920b:29ac:7e7a:91ff:fe6d:ffe2 dev enp0s25 srcport 0 0 dstport 8472 flowlabel 0x68 ageing 300 noudpcsum noudp6zerocsumtx noudp6zerocsumrx addrgenmode eui64 numtxqueues 1 numrxqueues 1
This patch add supports to configure IFLA_VXLAN_LOCAL
and IFLA_VXLAN_GROUP.
The "Group" is renamed to "Remote" which is a multicast address.`
```
Description=vxlan-test
Name=vxlan1
Kind=vxlan
[VXLAN]
Id=33
Local=2001:db8:2f4:4bff:fa71:1a56
Remote=FF02:0:0:0:0:0:1:9
```
output
```
ip -d link show vxlan1
16: vxlan1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1430 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/ether fe:b4:97:03:f8:e5 brd ff:ff:ff:ff:ff:ff promiscuity 0
vxlan id 33 group ff02::1:9 local 2001:db8:02f4:4bff:fa71:1a56 dev enp0s3 srcport 0 0 dstport 8472 ageing 300 noudpcsum noudp6zerocsumtx noudp6zerocsumrx addrgenmode none numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
```
active_slave:
Specifies the new active slave for modes that support it
(active-backup, balance-alb and balance-tlb).
primary slave:
systemd-networks currently lacks the capability to set the primary slave
in an
active-backup bonding. This is necessary if you prefer one interface
over the
other. A common example is a eth0-wlan0 bonding on a laptop where you'd
want to
switch to the wired connection whenever it's available.
Fixes: #2837
This patch adds support to remote checksum checksum offload to VXLAN.
This patch adds RemoteCheckSumTx and RemoteCheckSumRx vxlan configuration
to enable remote checksum offload for transmit and receive on the VXLAN tunnel.
Also update the description of drop-ins in systemd.unit(5) to say that .d
directories, not .conf files, are in /etc/system/system, /run/systemd/system,
etc.
This patch implements support for the IFLA_BR_MCAST_SNOOPING attribute
it can change the multicast snooping value.
IGMP snooping monitors the Internet Group Management Protocol (IGMP)
traffic between hosts and multicast routers.
This patch add support to configure port
PortRange:
VXLAN bases source UDP port based on flow to help the
receiver to be able to load balance based on outer header flow.
DestinatinPort:
Allow configuring the default destination port on a per-device basis.
Even when we use shortened, combined words, we still should uppercase
where a new word starts. I couldn't find a canonically capitalized
version of this term, hence I think we should follow our naming rules
here.
