IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The new lzma2 compression options at the top of compress_blob_xz are
equivalent to using preset "0", exept for using a 1 MiB dictionary
(the same as preset "1"). This makes the memory usage at most 7.5 MiB
in the compressor, and 1 MiB in the decompressor, instead of the
previous 92 MiB in the compressor and 8 MiB in the decompressor.
According to test-compress-benchmark this commit makes XZ compression
20 times faster, with no increase in compressed data size.
Using more realistic test data (an ELF binary rather than repeating
ASCII letters 'a' through 'z' in order) it only provides a factor 10
speedup, and at a cost if a 10% increase in compressed data size.
But that is still a worthwhile trade-off.
According to test-compress-benchmark XZ compression is still 25 times
slower than LZ4, but the compressed data is one eighth the size.
Using more realistic test data XZ compression is only 18 times slower
than LZ4, and the compressed data is only one quarter the size.
$ ./test-compress-benchmark
XZ: compressed & decompressed 2535300963 bytes in 42.30s (57.15MiB/s), mean compresion 99.95%, skipped 3570 bytes
LZ4: compressed & decompressed 2535303543 bytes in 1.60s (1510.60MiB/s), mean compresion 99.60%, skipped 990 bytes
Instead of waiting for new data from the sensor, which might be
a long time coming, depending on the sensor device, ask the kernel
for the last state for that particular input device.
If compositors use the new SwitchTo() logic to map F1-F12, we should allow
them to switch to unregistered VTs, too. Otherwise, the auto-spawn logic
of gettys won't trigger.
Reported-by: Jasper St. Pierre <jstpierre@mecheye.net>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
This patch adds supports networkd to configure bond mode
during creation via persistent conf. Mode can be configured
with conf param 'Mode'. A new section Bond is added to the
conf to support bond mode.
These modes can be configured now.
balance-rr
active-backup
balance-xor
broadcast
802.3ad
balance-tlb
balance-alb
Example conf file: test-bond.conf
[NetDev]
Name=bond1
Kind=bond
[Bond]
Mode=balance-xor
Test case:
1. start networkd service:
12: bond1: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc
noqueue state UNKNOWN mode DEFAULT group default
link/ether 22:89:6c:47:23:d2 brd ff:ff:ff:ff:ff:ff
2. find bond mode:
cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: load balancing (xor)
Transmit Hash Policy: layer2 (0)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
Changes:
1. Added file networkd-bond.c
2. Bond mode enum BondMode
3. conf section [Bond]
[tomegun: whitespace]
As Zbigniew pointed out a new ConditionFirstBoot= appears like the nicer
way to hook in systemd-firstboot.service on first boots (those with /etc
unpopulated), so let's do this, and get rid of the generator again.
We already ignore IP fragments, because we expect that Fragment
offset (FO) field is not set. However first fragment in a fragmented IP
flow will have all zeroes in FO field. We should ignore such packet as
well, thus we need to look at MF flag in the IP header. Checking MF flag
will filter out all except last packet in fragmented flows. Last one
will be ruled out by next check for value of FO.
