systemd Developer Lennart Poettering lennart@poettering.net systemd-mount 1 systemd-mount systemd-umount Establish and destroy transient mount or auto-mount points systemd-mount OPTIONS WHAT WHERE systemd-mount OPTIONS --list systemd-mount OPTIONS --umount WHAT|WHERE systemd-mount may be used to create and start a transient .mount or .automount unit of the file system WHAT on the mount point WHERE. In many ways, systemd-mount is similar to the lower-level mount8 command, however instead of executing the mount operation directly and immediately, systemd-mount schedules it through the service manager job queue, so that it may pull in further dependencies (such as parent mounts, or a file system checker to execute a priori), and may make use of the auto-mounting logic. The command takes either one or two arguments. If only one argument is specified it should refer to a block device or regular file containing a file system (e.g. /dev/sdb1 or /path/to/disk.img). If it is a block device, which is then probed for a label and other metadata, and is mounted to a directory whose name is generated from the label. In this mode the block device must exist at the time of invocation of the command, so that it may be probed. If the device is found to be a removable block device (e.g. a USB stick) an automount point instead of a regular mount point is created (i.e. the --automount= option is implied, see below). If two arguments are specified the first indicates the mount source (the WHAT) and the second indicates the path to mount it on (the WHERE). In this mode no probing of the source is attempted, and a backing device node doesn't have to exist yet. However, if this mode is combined with --discover, device node probing for additional metadata is enabled, and – much like in the single-argument case discussed above – the specified device has to exist at the time of invocation of the command. Use the --list command to show a terse table of all local, known block devices with file systems that may be mounted with this command. systemd-umount can be used to unmount a mount or automount point. It is the same as systemd-mount --umount. The following options are understood: --no-block Do not synchronously wait for the requested operation to finish. If this is not specified, the job will be verified, enqueued and systemd-mount will wait until the mount or automount unit's start-up is completed. By passing this argument, it is only verified and enqueued. --quiet -q Suppresses additional informational output while running. --discover Enable probing of the mount source. This switch is implied if a single argument is specified on the command line. If passed, additional metadata is read from the device to enhance the unit to create. For example, a descriptive string for the transient units is generated from the file system label and device model. Moreover if a removable block device (e.g. USB stick) is detected an automount unit instead of a regular mount unit is created, with a short idle time-out, in order to ensure the file-system is placed in a clean state quickly after each access. --type= -t Specifies the file system type to mount (e.g. vfat, ext4, …). If omitted (or set to auto) the file system is determined automatically. --options= -o Additional mount options for the mount point. --owner=USER Let the specified user USER own the mounted file system. This is done by appending uid= and gid= options to the list of mount options. Only certain file systems support this option. --fsck= Takes a boolean argument, defaults to on. Controls whether to run a file system check immediately before the mount operation. In the automount case (see --automount= below) the check will be run the moment the first access to the device is made, which might slightly delay the access. --description= Provide a description for the mount or automount unit. See Description= in systemd.unit5. --property= -p Sets a unit property for the mount unit that is created. This takes an assignment in the same format as systemctl1's set-property command. --automount= Takes a boolean argument. Controls whether to create an automount point or a regular mount point. If true an automount point is created that is backed by the actual file system at the time of first access. If false a plain mount point is created that is backed by the actual file system immediately. Automount points have the benefit that the file system stays unmounted and hence in clean state until it is first accessed. In automount mode the --timeout-idle-sec= switch (see below) may be used to ensure the mount point is unmounted automatically after the last access and an idle period passed. If this switch is not specified it defaults to false. If not specified and --discover is used (or only a single argument passed, which implies --discover, see above), and the file system block device is detected to be removable, it is set to true, in order to increase the chance that the file system is in a fully clean state if the device is unplugged abruptly. -A Equivalent to --automount=yes. --timeout-idle-sec= Takes a time value that controls the idle timeout in automount mode. If set to infinity (the default) no automatic unmounts are done. Otherwise the file system backing the automount point is detached after the last access and the idle timeout passed. See systemd.time7 for details on the time syntax supported. This option has no effect if only a regular mount is established, and automounting is not used. Note that if --discover is used (or only a single argument passed, which implies --discover, see above), and the file system block device is detected to be removable, --timeout-idle-sec=1s is implied. --automount-property= Similar to --property=, but applies additional properties to the automount unit created, instead of the mount unit. --bind-device= Takes a boolean argument, defaults to off. This option only has an effect in automount mode, and controls whether the automount unit shall be bound to the backing device's lifetime. If enabled, the automount point will be removed automatically when the backing device vanishes. If disabled the automount point stays around, and subsequent accesses will block until backing device is replugged. This option has no effect in case of non-device mounts, such as network or virtual file system mounts. Note that if --discover is used (or only a single argument passed, which implies --discover, see above), and the file system block device is detected to be removable, this option is implied. --list Instead of establishing a mount or automount point, print a terse list of block devices containing file systems that may be mounted with systemd-mount, along with useful metadata such as labels, etc. -u --umount Stop the mount and automount units corresponding to the specified mount points WHERE or the devices WHAT. systemd-mount with this option or systemd-umount can take multiple arguments which can be mount points, devices, /etc/fstab style node names, or backing files corresponding to loop devices, like systemd-mount --umount /path/to/umount /dev/sda1 UUID=xxxxxx-xxxx LABEL=xxxxx /path/to/disk.img. Note that when -H or -M is specified, only absolute paths to mount points are supported. -G --collect Unload the transient unit after it completed, even if it failed. Normally, without this option, all mount units that mount and failed are kept in memory until the user explicitly resets their failure state with systemctl reset-failed or an equivalent command. On the other hand, units that stopped successfully are unloaded immediately. If this option is turned on the "garbage collection" of units is more aggressive, and unloads units regardless if they exited successfully or failed. This option is a shortcut for --property=CollectMode=inactive-or-failed, see the explanation for CollectMode= in systemd.unit5 for further information. On success, 0 is returned, a non-zero failure code otherwise. If --discover is used, systemd-mount honors a couple of additional udev properties of block devices: SYSTEMD_MOUNT_OPTIONS= The mount options to use, if --options= is not used. SYSTEMD_MOUNT_WHERE= The file system path to place the mount point at, instead of the automatically generated one. systemd1, mount8, systemctl1, systemd.unit5, systemd.mount5, systemd.automount5, systemd-run1