systemd-sleep.conf systemd systemd-sleep.conf 5 systemd-sleep.conf sleep.conf.d Suspend and hibernation configuration file /etc/systemd/sleep.conf /etc/systemd/sleep.conf.d/*.conf /run/systemd/sleep.conf.d/*.conf /usr/lib/systemd/sleep.conf.d/*.conf Description systemd supports four general power-saving modes: suspend a low-power state where execution of the OS is paused, and complete power loss might result in lost data, and which is fast to enter and exit. This corresponds to suspend, standby, or freeze states as understood by the kernel. hibernate a low-power state where execution of the OS is paused, and complete power loss does not result in lost data, and which might be slow to enter and exit. This corresponds to the hibernation as understood by the kernel. hybrid-sleep a low-power state where execution of the OS is paused, which might be slow to enter, and on complete power loss does not result in lost data but might be slower to exit in that case. This mode is called suspend-to-both by the kernel. suspend-then-hibernate A low power state where the system is initially suspended (the state is stored in RAM) and then hibernated based on battery percentage capacity. If the current battery capacity is higher than 5%, the system goes back to suspend for interval calculated using battery discharge rate per hour. Battery discharge rate per hour is stored in a file which is created after initial suspend-resume cycle. The value is calculated using battery decreasing charge level a timespan. In case of manual wakeup before RTC alarm, the timespan is the duration for which system was suspended. If the file does not exist or has invalid value, initial suspend duration is set to HibernateDelaySec=. After wakeup via an RTC alarm, the battery discharge rate per hour is again estimated. If the current battery charge level is equal to or less than 5%, the system will be hibernated (the state is then stored on disk) else the system goes back to suspend for the amount of time it would take to fully discharge the battery minus 30 minutes. Settings in these files determine what strings will be written to /sys/power/disk and /sys/power/state by systemd-sleep8 when systemd1 attempts to suspend or hibernate the machine. See systemd.syntax7 for a general description of the syntax. Options The following options can be configured in the [Sleep] section of /etc/systemd/sleep.conf or a sleep.conf.d file: AllowSuspend= AllowHibernation= AllowSuspendThenHibernate= AllowHybridSleep= By default any power-saving mode is advertised if possible (i.e. the kernel supports that mode, the necessary resources are available). Those switches can be used to disable specific modes. If AllowHibernation=no or AllowSuspend=no is used, this implies AllowSuspendThenHibernate=no and AllowHybridSleep=no, since those methods use both suspend and hibernation internally. AllowSuspendThenHibernate=yes and AllowHybridSleep=yes can be used to override and enable those specific modes. SuspendMode= HibernateMode= HybridSleepMode= The string to be written to /sys/power/disk by, respectively, systemd-suspend.service8, systemd-hibernate.service8, or systemd-hybrid-sleep.service8. More than one value can be specified by separating multiple values with whitespace. They will be tried in turn, until one is written without error. If neither succeeds, the operation will be aborted. systemd-suspend-then-hibernate.service8 uses the value of SuspendMode= when suspending and the value of HibernateMode= when hibernating. SuspendState= HibernateState= HybridSleepState= The string to be written to /sys/power/state by, respectively, systemd-suspend.service8, systemd-hibernate.service8, or systemd-hybrid-sleep.service8. More than one value can be specified by separating multiple values with whitespace. They will be tried in turn, until one is written without error. If neither succeeds, the operation will be aborted. systemd-suspend-then-hibernate.service8 uses the value of SuspendState= when suspending and the value of HibernateState= when hibernating. HibernateDelaySec= The amount of time the system spends in suspend mode before the RTC alarm wakes the system, before the battery discharge rate can be estimated and used instead to calculate the suspension interval. systemd-suspend-then-hibernate.service8. Defaults to 2h. Example: freeze Example: to exploit the freeze mode added in Linux 3.9, one can use systemctl suspend with [Sleep] SuspendState=freeze See Also systemd-sleep8, systemd-suspend.service8, systemd-hibernate.service8, systemd-hybrid-sleep.service8, systemd-suspend-then-hibernate.service8, systemd1, systemd.directives7