linux/arch/mips/kernel/traps.c

2380 lines
58 KiB
C
Raw Normal View History

/*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*
* Copyright (C) 1994 - 1999, 2000, 01, 06 Ralf Baechle
* Copyright (C) 1995, 1996 Paul M. Antoine
* Copyright (C) 1998 Ulf Carlsson
* Copyright (C) 1999 Silicon Graphics, Inc.
* Kevin D. Kissell, kevink@mips.com and Carsten Langgaard, carstenl@mips.com
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
* Copyright (C) 2002, 2003, 2004, 2005, 2007 Maciej W. Rozycki
* Copyright (C) 2000, 2001, 2012 MIPS Technologies, Inc. All rights reserved.
* Copyright (C) 2014, Imagination Technologies Ltd.
*/
#include <linux/bitops.h>
#include <linux/bug.h>
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
#include <linux/compiler.h>
#include <linux/context_tracking.h>
#include <linux/cpu_pm.h>
#include <linux/kexec.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/mm.h>
#include <linux/sched.h>
#include <linux/smp.h>
#include <linux/spinlock.h>
#include <linux/kallsyms.h>
#include <linux/bootmem.h>
#include <linux/interrupt.h>
#include <linux/ptrace.h>
#include <linux/kgdb.h>
#include <linux/kdebug.h>
#include <linux/kprobes.h>
#include <linux/notifier.h>
#include <linux/kdb.h>
#include <linux/irq.h>
#include <linux/perf_event.h>
#include <asm/bootinfo.h>
#include <asm/branch.h>
#include <asm/break.h>
#include <asm/cop2.h>
#include <asm/cpu.h>
#include <asm/cpu-type.h>
#include <asm/dsp.h>
#include <asm/fpu.h>
#include <asm/fpu_emulator.h>
#include <asm/idle.h>
#include <asm/mips-r2-to-r6-emul.h>
#include <asm/mipsregs.h>
#include <asm/mipsmtregs.h>
#include <asm/module.h>
#include <asm/msa.h>
#include <asm/pgtable.h>
#include <asm/ptrace.h>
#include <asm/sections.h>
#include <asm/tlbdebug.h>
#include <asm/traps.h>
#include <asm/uaccess.h>
#include <asm/watch.h>
#include <asm/mmu_context.h>
#include <asm/types.h>
#include <asm/stacktrace.h>
#include <asm/uasm.h>
extern void check_wait(void);
extern asmlinkage void rollback_handle_int(void);
extern asmlinkage void handle_int(void);
MIPS: Make tlb exception handler definitions and declarations match. The code was written as it is because it's more expressive, a bit easier. But it's always been dirty, if not a bug. But we can't cheat with LTO compilers, so this results in: [...] LDFINAL vmlinux.o In file included from arch/mips/kernel/topology.c:604:0, from arch/mips/kernel/time.c:212, from arch/mips/kernel/syscall.c:300, from arch/mips/kernel/signal.c:853, from arch/mips/kernel/setup.c:1030, from arch/mips/kernel/reset.c:354, from arch/mips/kernel/ptrace.c:562, from arch/mips/kernel/process.c:770, from arch/mips/kernel/irq.c:350, from arch/mips/kernel/branch.c:321, from arch/mips/kernel/cpu-probe.c:1370, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:345, from arch/mips/sgi-ip22/ip22-gio.c:660, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/sgialib.h:219, from arch/mips/sgi-ip22/ip22-reset.c:224, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/paccess.h:116, from arch/mips/sgi-ip22/ip22-nvram.c:334, from include/linux/kernel_stat.h:79, from arch/mips/sgi-ip22/ip22-int.c:592, from arch/mips/sgi-ip22/ip22-hpc.c:470, from arch/mips/sgi-ip22/ip22-mc.c:135, from init/init_task.c:54, from init/calibrate.c:744, from init/noinitramfs.c:62, from init/do_mounts.c:573, from init/version.c:1009, from init/main.c:777, from :729: arch/mips/kernel/traps.c:63:49: error: variable ‘handle_tlbl’ redeclared as function In file included from arch/mips/mm/page.c:310:0, from arch/mips/mm/mmap.c:208, from arch/mips/mm/init.c:641, from arch/mips/mm/gup.c:811, from arch/mips/mm/fault.c:659, from include/linux/module.h:682, from arch/mips/mm/dma-default.c:161, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:397, from arch/mips/kernel/i8253.c:538, from arch/mips/kernel/proc.c:145, from arch/mips/kernel/irq_cpu.c:129, from arch/mips/kernel/i8259.c:229, from include/uapi/linux/elf.h:251, from arch/mips/kernel/mips_ksyms.c:129, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/time.h:50, from arch/mips/kernel/cevt-r4k.c:90, from arch/mips/kernel/vdso.c:136, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:351, from arch/mips/kernel/unaligned.c:809, from arch/mips/kernel/traps.c:1720, from arch/mips/kernel/topology.c:684, from arch/mips/kernel/time.c:212, from arch/mips/kernel/syscall.c:300, from arch/mips/kernel/signal.c:853, from arch/mips/kernel/setup.c:1030, from arch/mips/kernel/reset.c:354, from arch/mips/kernel/ptrace.c:562, from arch/mips/kernel/process.c:770, from arch/mips/kernel/irq.c:350, from arch/mips/kernel/branch.c:321, from arch/mips/kernel/cpu-probe.c:1370, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:345, from arch/mips/sgi-ip22/ip22-gio.c:660, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/sgialib.h:219, from arch/mips/sgi-ip22/ip22-reset.c:224, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/paccess.h:116, from arch/mips/sgi-ip22/ip22-nvram.c:334, from include/linux/kernel_stat.h:79, from arch/mips/sgi-ip22/ip22-int.c:592, from arch/mips/sgi-ip22/ip22-hpc.c:470, from arch/mips/sgi-ip22/ip22-mc.c:135, from init/init_task.c:54, from init/calibrate.c:744, from init/noinitramfs.c:62, from init/do_mounts.c:573, from init/version.c:1009, from init/main.c:777, from :729: arch/mips/mm/tlbex.c:1448:5: note: previously declared here In file included from arch/mips/kernel/topology.c:604:0, from arch/mips/kernel/time.c:212, from arch/mips/kernel/syscall.c:300, from arch/mips/kernel/signal.c:853, from arch/mips/kernel/setup.c:1030, from arch/mips/kernel/reset.c:354, from arch/mips/kernel/ptrace.c:562, from arch/mips/kernel/process.c:770, from arch/mips/kernel/irq.c:350, from arch/mips/kernel/branch.c:321, from arch/mips/kernel/cpu-probe.c:1370, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:345, from arch/mips/sgi-ip22/ip22-gio.c:660, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/sgialib.h:219, from arch/mips/sgi-ip22/ip22-reset.c:224, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/paccess.h:116, from arch/mips/sgi-ip22/ip22-nvram.c:334, from include/linux/kernel_stat.h:79, from arch/mips/sgi-ip22/ip22-int.c:592, from arch/mips/sgi-ip22/ip22-hpc.c:470, from arch/mips/sgi-ip22/ip22-mc.c:135, from init/init_task.c:54, from init/calibrate.c:744, from init/noinitramfs.c:62, from init/do_mounts.c:573, from init/version.c:1009, from init/main.c:777, from :729: arch/mips/kernel/traps.c:62:49: error: variable ‘handle_tlbm’ redeclared as function In file included from arch/mips/mm/page.c:310:0, from arch/mips/mm/mmap.c:208, from arch/mips/mm/init.c:641, from arch/mips/mm/gup.c:811, from arch/mips/mm/fault.c:659, from include/linux/module.h:682, from arch/mips/mm/dma-default.c:161, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:397, from arch/mips/kernel/i8253.c:538, from arch/mips/kernel/proc.c:145, from arch/mips/kernel/irq_cpu.c:129, from arch/mips/kernel/i8259.c:229, from include/uapi/linux/elf.h:251, from arch/mips/kernel/mips_ksyms.c:129, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/time.h:50, from arch/mips/kernel/cevt-r4k.c:90, from arch/mips/kernel/vdso.c:136, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:351, from arch/mips/kernel/unaligned.c:809, from arch/mips/kernel/traps.c:1720, from arch/mips/kernel/topology.c:684, from arch/mips/kernel/time.c:212, from arch/mips/kernel/syscall.c:300, from arch/mips/kernel/signal.c:853, from arch/mips/kernel/setup.c:1030, from arch/mips/kernel/reset.c:354, from arch/mips/kernel/ptrace.c:562, from arch/mips/kernel/process.c:770, from arch/mips/kernel/irq.c:350, from arch/mips/kernel/branch.c:321, from arch/mips/kernel/cpu-probe.c:1370, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:345, from arch/mips/sgi-ip22/ip22-gio.c:660, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/sgialib.h:219, from arch/mips/sgi-ip22/ip22-reset.c:224, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/paccess.h:116, from arch/mips/sgi-ip22/ip22-nvram.c:334, from include/linux/kernel_stat.h:79, from arch/mips/sgi-ip22/ip22-int.c:592, from arch/mips/sgi-ip22/ip22-hpc.c:470, from arch/mips/sgi-ip22/ip22-mc.c:135, from init/init_task.c:54, from init/calibrate.c:744, from init/noinitramfs.c:62, from init/do_mounts.c:573, from init/version.c:1009, from init/main.c:777, from :729: arch/mips/mm/tlbex.c:1450:5: note: previously declared here In file included from arch/mips/kernel/topology.c:604:0, from arch/mips/kernel/time.c:212, from arch/mips/kernel/syscall.c:300, from arch/mips/kernel/signal.c:853, from arch/mips/kernel/setup.c:1030, from arch/mips/kernel/reset.c:354, from arch/mips/kernel/ptrace.c:562, from arch/mips/kernel/process.c:770, from arch/mips/kernel/irq.c:350, from arch/mips/kernel/branch.c:321, from arch/mips/kernel/cpu-probe.c:1370, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:345, from arch/mips/sgi-ip22/ip22-gio.c:660, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/sgialib.h:219, from arch/mips/sgi-ip22/ip22-reset.c:224, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/paccess.h:116, from arch/mips/sgi-ip22/ip22-nvram.c:334, from include/linux/kernel_stat.h:79, from arch/mips/sgi-ip22/ip22-int.c:592, from arch/mips/sgi-ip22/ip22-hpc.c:470, from arch/mips/sgi-ip22/ip22-mc.c:135, from init/init_task.c:54, from init/calibrate.c:744, from init/noinitramfs.c:62, from init/do_mounts.c:573, from init/version.c:1009, from init/main.c:777, from :729: arch/mips/kernel/traps.c:64:49: error: variable ‘handle_tlbs’ redeclared as function In file included from arch/mips/mm/page.c:310:0, from arch/mips/mm/mmap.c:208, from arch/mips/mm/init.c:641, from arch/mips/mm/gup.c:811, from arch/mips/mm/fault.c:659, from include/linux/module.h:682, from arch/mips/mm/dma-default.c:161, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:397, from arch/mips/kernel/i8253.c:538, from arch/mips/kernel/proc.c:145, from arch/mips/kernel/irq_cpu.c:129, from arch/mips/kernel/i8259.c:229, from include/uapi/linux/elf.h:251, from arch/mips/kernel/mips_ksyms.c:129, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/time.h:50, from arch/mips/kernel/cevt-r4k.c:90, from arch/mips/kernel/vdso.c:136, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:351, from arch/mips/kernel/unaligned.c:809, from arch/mips/kernel/traps.c:1720, from arch/mips/kernel/topology.c:684, from arch/mips/kernel/time.c:212, from arch/mips/kernel/syscall.c:300, from arch/mips/kernel/signal.c:853, from arch/mips/kernel/setup.c:1030, from arch/mips/kernel/reset.c:354, from arch/mips/kernel/ptrace.c:562, from arch/mips/kernel/process.c:770, from arch/mips/kernel/irq.c:350, from arch/mips/kernel/branch.c:321, from arch/mips/kernel/cpu-probe.c:1370, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:345, from arch/mips/sgi-ip22/ip22-gio.c:660, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/sgialib.h:219, from arch/mips/sgi-ip22/ip22-reset.c:224, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/paccess.h:116, from arch/mips/sgi-ip22/ip22-nvram.c:334, from include/linux/kernel_stat.h:79, from arch/mips/sgi-ip22/ip22-int.c:592, from arch/mips/sgi-ip22/ip22-hpc.c:470, from arch/mips/sgi-ip22/ip22-mc.c:135, from init/init_task.c:54, from init/calibrate.c:744, from init/noinitramfs.c:62, from init/do_mounts.c:573, from init/version.c:1009, from init/main.c:777, from :729: arch/mips/mm/tlbex.c:1449:5: note: previously declared here lto1: fatal error: errors during merging of translation units compilation terminated. lto-wrapper: /usr/bin/mips-linux-gcc returned 1 exit status /usr/lib64/gcc/mips-linux/4.7.1/../../../../mips-linux/bin/ld: lto-wrapper failed collect2: error: ld returned 1 exit status make: *** [vmlinux] Error 1 Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2013-02-08 04:21:34 +04:00
extern u32 handle_tlbl[];
extern u32 handle_tlbs[];
extern u32 handle_tlbm[];
extern asmlinkage void handle_adel(void);
extern asmlinkage void handle_ades(void);
extern asmlinkage void handle_ibe(void);
extern asmlinkage void handle_dbe(void);
extern asmlinkage void handle_sys(void);
extern asmlinkage void handle_bp(void);
extern asmlinkage void handle_ri(void);
extern asmlinkage void handle_ri_rdhwr_vivt(void);
extern asmlinkage void handle_ri_rdhwr(void);
extern asmlinkage void handle_cpu(void);
extern asmlinkage void handle_ov(void);
extern asmlinkage void handle_tr(void);
extern asmlinkage void handle_msa_fpe(void);
extern asmlinkage void handle_fpe(void);
extern asmlinkage void handle_ftlb(void);
extern asmlinkage void handle_msa(void);
extern asmlinkage void handle_mdmx(void);
extern asmlinkage void handle_watch(void);
extern asmlinkage void handle_mt(void);
extern asmlinkage void handle_dsp(void);
extern asmlinkage void handle_mcheck(void);
extern asmlinkage void handle_reserved(void);
extern void tlb_do_page_fault_0(void);
void (*board_be_init)(void);
int (*board_be_handler)(struct pt_regs *regs, int is_fixup);
void (*board_nmi_handler_setup)(void);
void (*board_ejtag_handler_setup)(void);
void (*board_bind_eic_interrupt)(int irq, int regset);
void (*board_ebase_setup)(void);
MIPS: Delete __cpuinit/__CPUINIT usage from MIPS code commit 3747069b25e419f6b51395f48127e9812abc3596 upstream. The __cpuinit type of throwaway sections might have made sense some time ago when RAM was more constrained, but now the savings do not offset the cost and complications. For example, the fix in commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time") is a good example of the nasty type of bugs that can be created with improper use of the various __init prefixes. After a discussion on LKML[1] it was decided that cpuinit should go the way of devinit and be phased out. Once all the users are gone, we can then finally remove the macros themselves from linux/init.h. Note that some harmless section mismatch warnings may result, since notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c) and are flagged as __cpuinit -- so if we remove the __cpuinit from the arch specific callers, we will also get section mismatch warnings. As an intermediate step, we intend to turn the linux/init.h cpuinit related content into no-ops as early as possible, since that will get rid of these warnings. In any case, they are temporary and harmless. Here, we remove all the MIPS __cpuinit from C code and __CPUINIT from asm files. MIPS is interesting in this respect, because there are also uasm users hiding behind their own renamed versions of the __cpuinit macros. [1] https://lkml.org/lkml/2013/5/20/589 [ralf@linux-mips.org: Folded in Paul's followup fix.] Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5494/ Patchwork: https://patchwork.linux-mips.org/patch/5495/ Patchwork: https://patchwork.linux-mips.org/patch/5509/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2013-06-18 17:38:59 +04:00
void(*board_cache_error_setup)(void);
static void show_raw_backtrace(unsigned long reg29)
{
unsigned long *sp = (unsigned long *)(reg29 & ~3);
unsigned long addr;
printk("Call Trace:");
#ifdef CONFIG_KALLSYMS
printk("\n");
#endif
while (!kstack_end(sp)) {
unsigned long __user *p =
(unsigned long __user *)(unsigned long)sp++;
if (__get_user(addr, p)) {
printk(" (Bad stack address)");
break;
}
if (__kernel_text_address(addr))
print_ip_sym(addr);
}
printk("\n");
}
#ifdef CONFIG_KALLSYMS
int raw_show_trace;
static int __init set_raw_show_trace(char *str)
{
raw_show_trace = 1;
return 1;
}
__setup("raw_show_trace", set_raw_show_trace);
#endif
static void show_backtrace(struct task_struct *task, const struct pt_regs *regs)
{
unsigned long sp = regs->regs[29];
unsigned long ra = regs->regs[31];
unsigned long pc = regs->cp0_epc;
if (!task)
task = current;
if (raw_show_trace || !__kernel_text_address(pc)) {
show_raw_backtrace(sp);
return;
}
printk("Call Trace:\n");
do {
print_ip_sym(pc);
pc = unwind_stack(task, &sp, pc, &ra);
} while (pc);
printk("\n");
}
/*
* This routine abuses get_user()/put_user() to reference pointers
* with at least a bit of error checking ...
*/
static void show_stacktrace(struct task_struct *task,
const struct pt_regs *regs)
{
const int field = 2 * sizeof(unsigned long);
long stackdata;
int i;
unsigned long __user *sp = (unsigned long __user *)regs->regs[29];
printk("Stack :");
i = 0;
while ((unsigned long) sp & (PAGE_SIZE - 1)) {
if (i && ((i % (64 / field)) == 0))
printk("\n ");
if (i > 39) {
printk(" ...");
break;
}
if (__get_user(stackdata, sp++)) {
printk(" (Bad stack address)");
break;
}
printk(" %0*lx", field, stackdata);
i++;
}
printk("\n");
show_backtrace(task, regs);
}
void show_stack(struct task_struct *task, unsigned long *sp)
{
struct pt_regs regs;
if (sp) {
regs.regs[29] = (unsigned long)sp;
regs.regs[31] = 0;
regs.cp0_epc = 0;
} else {
if (task && task != current) {
regs.regs[29] = task->thread.reg29;
regs.regs[31] = 0;
regs.cp0_epc = task->thread.reg31;
#ifdef CONFIG_KGDB_KDB
} else if (atomic_read(&kgdb_active) != -1 &&
kdb_current_regs) {
memcpy(&regs, kdb_current_regs, sizeof(regs));
#endif /* CONFIG_KGDB_KDB */
} else {
prepare_frametrace(&regs);
}
}
show_stacktrace(task, &regs);
}
static void show_code(unsigned int __user *pc)
{
long i;
unsigned short __user *pc16 = NULL;
printk("\nCode:");
if ((unsigned long)pc & 1)
pc16 = (unsigned short __user *)((unsigned long)pc & ~1);
for(i = -3 ; i < 6 ; i++) {
unsigned int insn;
if (pc16 ? __get_user(insn, pc16 + i) : __get_user(insn, pc + i)) {
printk(" (Bad address in epc)\n");
break;
}
printk("%c%0*x%c", (i?' ':'<'), pc16 ? 4 : 8, insn, (i?' ':'>'));
}
}
static void __show_regs(const struct pt_regs *regs)
{
const int field = 2 * sizeof(unsigned long);
unsigned int cause = regs->cp0_cause;
unsigned int exccode;
int i;
dump_stack: unify debug information printed by show_regs() show_regs() is inherently arch-dependent but it does make sense to print generic debug information and some archs already do albeit in slightly different forms. This patch introduces a generic function to print debug information from show_regs() so that different archs print out the same information and it's much easier to modify what's printed. show_regs_print_info() prints out the same debug info as dump_stack() does plus task and thread_info pointers. * Archs which didn't print debug info now do. alpha, arc, blackfin, c6x, cris, frv, h8300, hexagon, ia64, m32r, metag, microblaze, mn10300, openrisc, parisc, score, sh64, sparc, um, xtensa * Already prints debug info. Replaced with show_regs_print_info(). The printed information is superset of what used to be there. arm, arm64, avr32, mips, powerpc, sh32, tile, unicore32, x86 * s390 is special in that it used to print arch-specific information along with generic debug info. Heiko and Martin think that the arch-specific extra isn't worth keeping s390 specfic implementation. Converted to use the generic version. Note that now all archs print the debug info before actual register dumps. An example BUG() dump follows. kernel BUG at /work/os/work/kernel/workqueue.c:4841! invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.9.0-rc1-work+ #7 Hardware name: empty empty/S3992, BIOS 080011 10/26/2007 task: ffff88007c85e040 ti: ffff88007c860000 task.ti: ffff88007c860000 RIP: 0010:[<ffffffff8234a07e>] [<ffffffff8234a07e>] init_workqueues+0x4/0x6 RSP: 0000:ffff88007c861ec8 EFLAGS: 00010246 RAX: ffff88007c861fd8 RBX: ffffffff824466a8 RCX: 0000000000000001 RDX: 0000000000000046 RSI: 0000000000000001 RDI: ffffffff8234a07a RBP: ffff88007c861ec8 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000000 R12: ffffffff8234a07a R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff88007dc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: ffff88015f7ff000 CR3: 00000000021f1000 CR4: 00000000000007f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Stack: ffff88007c861ef8 ffffffff81000312 ffffffff824466a8 ffff88007c85e650 0000000000000003 0000000000000000 ffff88007c861f38 ffffffff82335e5d ffff88007c862080 ffffffff8223d8c0 ffff88007c862080 ffffffff81c47760 Call Trace: [<ffffffff81000312>] do_one_initcall+0x122/0x170 [<ffffffff82335e5d>] kernel_init_freeable+0x9b/0x1c8 [<ffffffff81c47760>] ? rest_init+0x140/0x140 [<ffffffff81c4776e>] kernel_init+0xe/0xf0 [<ffffffff81c6be9c>] ret_from_fork+0x7c/0xb0 [<ffffffff81c47760>] ? rest_init+0x140/0x140 ... v2: Typo fix in x86-32. v3: CPU number dropped from show_regs_print_info() as dump_stack_print_info() has been updated to print it. s390 specific implementation dropped as requested by s390 maintainers. Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: David S. Miller <davem@davemloft.net> Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Fengguang Wu <fengguang.wu@intel.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Sam Ravnborg <sam@ravnborg.org> Acked-by: Chris Metcalf <cmetcalf@tilera.com> [tile bits] Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon bits] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-05-01 02:27:17 +04:00
show_regs_print_info(KERN_DEFAULT);
/*
* Saved main processor registers
*/
for (i = 0; i < 32; ) {
if ((i % 4) == 0)
printk("$%2d :", i);
if (i == 0)
printk(" %0*lx", field, 0UL);
else if (i == 26 || i == 27)
printk(" %*s", field, "");
else
printk(" %0*lx", field, regs->regs[i]);
i++;
if ((i % 4) == 0)
printk("\n");
}
#ifdef CONFIG_CPU_HAS_SMARTMIPS
printk("Acx : %0*lx\n", field, regs->acx);
#endif
printk("Hi : %0*lx\n", field, regs->hi);
printk("Lo : %0*lx\n", field, regs->lo);
/*
* Saved cp0 registers
*/
printk("epc : %0*lx %pS\n", field, regs->cp0_epc,
(void *) regs->cp0_epc);
printk("ra : %0*lx %pS\n", field, regs->regs[31],
(void *) regs->regs[31]);
printk("Status: %08x ", (uint32_t) regs->cp0_status);
if (cpu_has_3kex) {
if (regs->cp0_status & ST0_KUO)
printk("KUo ");
if (regs->cp0_status & ST0_IEO)
printk("IEo ");
if (regs->cp0_status & ST0_KUP)
printk("KUp ");
if (regs->cp0_status & ST0_IEP)
printk("IEp ");
if (regs->cp0_status & ST0_KUC)
printk("KUc ");
if (regs->cp0_status & ST0_IEC)
printk("IEc ");
} else if (cpu_has_4kex) {
if (regs->cp0_status & ST0_KX)
printk("KX ");
if (regs->cp0_status & ST0_SX)
printk("SX ");
if (regs->cp0_status & ST0_UX)
printk("UX ");
switch (regs->cp0_status & ST0_KSU) {
case KSU_USER:
printk("USER ");
break;
case KSU_SUPERVISOR:
printk("SUPERVISOR ");
break;
case KSU_KERNEL:
printk("KERNEL ");
break;
default:
printk("BAD_MODE ");
break;
}
if (regs->cp0_status & ST0_ERL)
printk("ERL ");
if (regs->cp0_status & ST0_EXL)
printk("EXL ");
if (regs->cp0_status & ST0_IE)
printk("IE ");
}
printk("\n");
exccode = (cause & CAUSEF_EXCCODE) >> CAUSEB_EXCCODE;
printk("Cause : %08x (ExcCode %02x)\n", cause, exccode);
if (1 <= exccode && exccode <= 5)
printk("BadVA : %0*lx\n", field, regs->cp0_badvaddr);
printk("PrId : %08x (%s)\n", read_c0_prid(),
cpu_name_string());
}
/*
* FIXME: really the generic show_regs should take a const pointer argument.
*/
void show_regs(struct pt_regs *regs)
{
__show_regs((struct pt_regs *)regs);
}
void show_registers(struct pt_regs *regs)
{
const int field = 2 * sizeof(unsigned long);
mm_segment_t old_fs = get_fs();
__show_regs(regs);
print_modules();
printk("Process %s (pid: %d, threadinfo=%p, task=%p, tls=%0*lx)\n",
current->comm, current->pid, current_thread_info(), current,
field, current_thread_info()->tp_value);
if (cpu_has_userlocal) {
unsigned long tls;
tls = read_c0_userlocal();
if (tls != current_thread_info()->tp_value)
printk("*HwTLS: %0*lx\n", field, tls);
}
if (!user_mode(regs))
/* Necessary for getting the correct stack content */
set_fs(KERNEL_DS);
show_stacktrace(current, regs);
show_code((unsigned int __user *) regs->cp0_epc);
printk("\n");
set_fs(old_fs);
}
static int regs_to_trapnr(struct pt_regs *regs)
{
return (regs->cp0_cause >> 2) & 0x1f;
}
static DEFINE_RAW_SPINLOCK(die_lock);
void __noreturn die(const char *str, struct pt_regs *regs)
{
static int die_counter;
int sig = SIGSEGV;
oops_enter();
if (notify_die(DIE_OOPS, str, regs, 0, regs_to_trapnr(regs),
SIGSEGV) == NOTIFY_STOP)
sig = 0;
console_verbose();
raw_spin_lock_irq(&die_lock);
bust_spinlocks(1);
printk("%s[#%d]:\n", str, ++die_counter);
show_registers(regs);
add_taint(TAINT_DIE, LOCKDEP_NOW_UNRELIABLE);
raw_spin_unlock_irq(&die_lock);
oops_exit();
if (in_interrupt())
panic("Fatal exception in interrupt");
if (panic_on_oops) {
printk(KERN_EMERG "Fatal exception: panic in 5 seconds");
ssleep(5);
panic("Fatal exception");
}
if (regs && kexec_should_crash(current))
crash_kexec(regs);
do_exit(sig);
}
extern struct exception_table_entry __start___dbe_table[];
extern struct exception_table_entry __stop___dbe_table[];
__asm__(
" .section __dbe_table, \"a\"\n"
" .previous \n");
/* Given an address, look for it in the exception tables. */
static const struct exception_table_entry *search_dbe_tables(unsigned long addr)
{
const struct exception_table_entry *e;
e = search_extable(__start___dbe_table, __stop___dbe_table - 1, addr);
if (!e)
e = search_module_dbetables(addr);
return e;
}
asmlinkage void do_be(struct pt_regs *regs)
{
const int field = 2 * sizeof(unsigned long);
const struct exception_table_entry *fixup = NULL;
int data = regs->cp0_cause & 4;
int action = MIPS_BE_FATAL;
enum ctx_state prev_state;
prev_state = exception_enter();
/* XXX For now. Fixme, this searches the wrong table ... */
if (data && !user_mode(regs))
fixup = search_dbe_tables(exception_epc(regs));
if (fixup)
action = MIPS_BE_FIXUP;
if (board_be_handler)
action = board_be_handler(regs, fixup != NULL);
switch (action) {
case MIPS_BE_DISCARD:
goto out;
case MIPS_BE_FIXUP:
if (fixup) {
regs->cp0_epc = fixup->nextinsn;
goto out;
}
break;
default:
break;
}
/*
* Assume it would be too dangerous to continue ...
*/
printk(KERN_ALERT "%s bus error, epc == %0*lx, ra == %0*lx\n",
data ? "Data" : "Instruction",
field, regs->cp0_epc, field, regs->regs[31]);
if (notify_die(DIE_OOPS, "bus error", regs, 0, regs_to_trapnr(regs),
SIGBUS) == NOTIFY_STOP)
goto out;
die_if_kernel("Oops", regs);
force_sig(SIGBUS, current);
out:
exception_exit(prev_state);
}
/*
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
* ll/sc, rdhwr, sync emulation
*/
#define OPCODE 0xfc000000
#define BASE 0x03e00000
#define RT 0x001f0000
#define OFFSET 0x0000ffff
#define LL 0xc0000000
#define SC 0xe0000000
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
#define SPEC0 0x00000000
#define SPEC3 0x7c000000
#define RD 0x0000f800
#define FUNC 0x0000003f
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
#define SYNC 0x0000000f
#define RDHWR 0x0000003b
/* microMIPS definitions */
#define MM_POOL32A_FUNC 0xfc00ffff
#define MM_RDHWR 0x00006b3c
#define MM_RS 0x001f0000
#define MM_RT 0x03e00000
/*
* The ll_bit is cleared by r*_switch.S
*/
unsigned int ll_bit;
struct task_struct *ll_task;
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
static inline int simulate_ll(struct pt_regs *regs, unsigned int opcode)
{
unsigned long value, __user *vaddr;
long offset;
/*
* analyse the ll instruction that just caused a ri exception
* and put the referenced address to addr.
*/
/* sign extend offset */
offset = opcode & OFFSET;
offset <<= 16;
offset >>= 16;
vaddr = (unsigned long __user *)
((unsigned long)(regs->regs[(opcode & BASE) >> 21]) + offset);
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
if ((unsigned long)vaddr & 3)
return SIGBUS;
if (get_user(value, vaddr))
return SIGSEGV;
preempt_disable();
if (ll_task == NULL || ll_task == current) {
ll_bit = 1;
} else {
ll_bit = 0;
}
ll_task = current;
preempt_enable();
regs->regs[(opcode & RT) >> 16] = value;
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
return 0;
}
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
static inline int simulate_sc(struct pt_regs *regs, unsigned int opcode)
{
unsigned long __user *vaddr;
unsigned long reg;
long offset;
/*
* analyse the sc instruction that just caused a ri exception
* and put the referenced address to addr.
*/
/* sign extend offset */
offset = opcode & OFFSET;
offset <<= 16;
offset >>= 16;
vaddr = (unsigned long __user *)
((unsigned long)(regs->regs[(opcode & BASE) >> 21]) + offset);
reg = (opcode & RT) >> 16;
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
if ((unsigned long)vaddr & 3)
return SIGBUS;
preempt_disable();
if (ll_bit == 0 || ll_task != current) {
regs->regs[reg] = 0;
preempt_enable();
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
return 0;
}
preempt_enable();
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
if (put_user(regs->regs[reg], vaddr))
return SIGSEGV;
regs->regs[reg] = 1;
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
return 0;
}
/*
* ll uses the opcode of lwc0 and sc uses the opcode of swc0. That is both
* opcodes are supposed to result in coprocessor unusable exceptions if
* executed on ll/sc-less processors. That's the theory. In practice a
* few processors such as NEC's VR4100 throw reserved instruction exceptions
* instead, so we're doing the emulation thing in both exception handlers.
*/
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
static int simulate_llsc(struct pt_regs *regs, unsigned int opcode)
{
if ((opcode & OPCODE) == LL) {
perf_sw_event(PERF_COUNT_SW_EMULATION_FAULTS,
1, regs, 0);
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
return simulate_ll(regs, opcode);
}
if ((opcode & OPCODE) == SC) {
perf_sw_event(PERF_COUNT_SW_EMULATION_FAULTS,
1, regs, 0);
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
return simulate_sc(regs, opcode);
}
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
return -1; /* Must be something else ... */
}
/*
* Simulate trapping 'rdhwr' instructions to provide user accessible
* registers not implemented in hardware.
*/
static int simulate_rdhwr(struct pt_regs *regs, int rd, int rt)
{
struct thread_info *ti = task_thread_info(current);
perf_sw_event(PERF_COUNT_SW_EMULATION_FAULTS,
1, regs, 0);
switch (rd) {
case 0: /* CPU number */
regs->regs[rt] = smp_processor_id();
return 0;
case 1: /* SYNCI length */
regs->regs[rt] = min(current_cpu_data.dcache.linesz,
current_cpu_data.icache.linesz);
return 0;
case 2: /* Read count register */
regs->regs[rt] = read_c0_count();
return 0;
case 3: /* Count register resolution */
switch (current_cpu_type()) {
case CPU_20KC:
case CPU_25KF:
regs->regs[rt] = 1;
break;
default:
regs->regs[rt] = 2;
}
return 0;
case 29:
regs->regs[rt] = ti->tp_value;
return 0;
default:
return -1;
}
}
static int simulate_rdhwr_normal(struct pt_regs *regs, unsigned int opcode)
{
if ((opcode & OPCODE) == SPEC3 && (opcode & FUNC) == RDHWR) {
int rd = (opcode & RD) >> 11;
int rt = (opcode & RT) >> 16;
simulate_rdhwr(regs, rd, rt);
return 0;
}
/* Not ours. */
return -1;
}
static int simulate_rdhwr_mm(struct pt_regs *regs, unsigned short opcode)
{
if ((opcode & MM_POOL32A_FUNC) == MM_RDHWR) {
int rd = (opcode & MM_RS) >> 16;
int rt = (opcode & MM_RT) >> 21;
simulate_rdhwr(regs, rd, rt);
return 0;
}
/* Not ours. */
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
return -1;
}
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
static int simulate_sync(struct pt_regs *regs, unsigned int opcode)
{
if ((opcode & OPCODE) == SPEC0 && (opcode & FUNC) == SYNC) {
perf_sw_event(PERF_COUNT_SW_EMULATION_FAULTS,
1, regs, 0);
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
return 0;
}
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
return -1; /* Must be something else ... */
}
asmlinkage void do_ov(struct pt_regs *regs)
{
enum ctx_state prev_state;
siginfo_t info;
prev_state = exception_enter();
die_if_kernel("Integer overflow", regs);
info.si_code = FPE_INTOVF;
info.si_signo = SIGFPE;
info.si_errno = 0;
info.si_addr = (void __user *) regs->cp0_epc;
force_sig_info(SIGFPE, &info, current);
exception_exit(prev_state);
}
int process_fpemu_return(int sig, void __user *fault_addr, unsigned long fcr31)
{
struct siginfo si = { 0 };
switch (sig) {
case 0:
return 0;
case SIGFPE:
si.si_addr = fault_addr;
si.si_signo = sig;
/*
* Inexact can happen together with Overflow or Underflow.
* Respect the mask to deliver the correct exception.
*/
fcr31 &= (fcr31 & FPU_CSR_ALL_E) <<
(ffs(FPU_CSR_ALL_X) - ffs(FPU_CSR_ALL_E));
if (fcr31 & FPU_CSR_INV_X)
si.si_code = FPE_FLTINV;
else if (fcr31 & FPU_CSR_DIV_X)
si.si_code = FPE_FLTDIV;
else if (fcr31 & FPU_CSR_OVF_X)
si.si_code = FPE_FLTOVF;
else if (fcr31 & FPU_CSR_UDF_X)
si.si_code = FPE_FLTUND;
else if (fcr31 & FPU_CSR_INE_X)
si.si_code = FPE_FLTRES;
else
si.si_code = __SI_FAULT;
force_sig_info(sig, &si, current);
return 1;
case SIGBUS:
si.si_addr = fault_addr;
si.si_signo = sig;
si.si_code = BUS_ADRERR;
force_sig_info(sig, &si, current);
return 1;
case SIGSEGV:
si.si_addr = fault_addr;
si.si_signo = sig;
down_read(&current->mm->mmap_sem);
if (find_vma(current->mm, (unsigned long)fault_addr))
si.si_code = SEGV_ACCERR;
else
si.si_code = SEGV_MAPERR;
up_read(&current->mm->mmap_sem);
force_sig_info(sig, &si, current);
return 1;
default:
force_sig(sig, current);
return 1;
}
}
MIPS: Support for hybrid FPRs Hybrid FPRs is a scheme where scalar FP registers are 64b wide, but accesses to odd indexed single registers use bits 63:32 of the preceeding even indexed 64b register. In this mode all FP code except that built for the plain FP64 ABI can execute correctly. Most notably a combination of FP64A & FP32 code can execute correctly, allowing for existing FP32 binaries to be linked with new FP64A binaries that can make use of 64 bit FP & MSA. Hybrid FPRs are implemented by setting both the FR & FRE bits, trapping & emulating single precision FP instructions (via Reserved Instruction exceptions) whilst allowing others to execute natively. It therefore has a penalty in terms of execution speed, and should only be used when no fully native mode can be. As more binaries are recompiled to use either the FPXX or FP64(A) ABIs, the need for hybrid FPRs should diminish. However in the short to mid term it allows for a gradual transition towards that world, rather than a complete ABI break which is not feasible for some users & not desirable for many. A task will be executed using the hybrid FPR scheme when its TIF_HYBRID_FPREGS flag is set & TIF_32BIT_FPREGS is clear. A further patch will set the flags as necessary, this patch simply adds the infrastructure necessary for the hybrid FPR mode to work. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: linux-fsdevel@vger.kernel.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/7683/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2014-09-11 11:30:20 +04:00
static int simulate_fp(struct pt_regs *regs, unsigned int opcode,
unsigned long old_epc, unsigned long old_ra)
{
union mips_instruction inst = { .word = opcode };
void __user *fault_addr;
unsigned long fcr31;
MIPS: Support for hybrid FPRs Hybrid FPRs is a scheme where scalar FP registers are 64b wide, but accesses to odd indexed single registers use bits 63:32 of the preceeding even indexed 64b register. In this mode all FP code except that built for the plain FP64 ABI can execute correctly. Most notably a combination of FP64A & FP32 code can execute correctly, allowing for existing FP32 binaries to be linked with new FP64A binaries that can make use of 64 bit FP & MSA. Hybrid FPRs are implemented by setting both the FR & FRE bits, trapping & emulating single precision FP instructions (via Reserved Instruction exceptions) whilst allowing others to execute natively. It therefore has a penalty in terms of execution speed, and should only be used when no fully native mode can be. As more binaries are recompiled to use either the FPXX or FP64(A) ABIs, the need for hybrid FPRs should diminish. However in the short to mid term it allows for a gradual transition towards that world, rather than a complete ABI break which is not feasible for some users & not desirable for many. A task will be executed using the hybrid FPR scheme when its TIF_HYBRID_FPREGS flag is set & TIF_32BIT_FPREGS is clear. A further patch will set the flags as necessary, this patch simply adds the infrastructure necessary for the hybrid FPR mode to work. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: linux-fsdevel@vger.kernel.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/7683/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2014-09-11 11:30:20 +04:00
int sig;
/* If it's obviously not an FP instruction, skip it */
switch (inst.i_format.opcode) {
case cop1_op:
case cop1x_op:
case lwc1_op:
case ldc1_op:
case swc1_op:
case sdc1_op:
break;
default:
return -1;
}
/*
* do_ri skipped over the instruction via compute_return_epc, undo
* that for the FPU emulator.
*/
regs->cp0_epc = old_epc;
regs->regs[31] = old_ra;
/* Save the FP context to struct thread_struct */
lose_fpu(1);
/* Run the emulator */
sig = fpu_emulator_cop1Handler(regs, &current->thread.fpu, 1,
&fault_addr);
fcr31 = current->thread.fpu.fcr31;
MIPS: Support for hybrid FPRs Hybrid FPRs is a scheme where scalar FP registers are 64b wide, but accesses to odd indexed single registers use bits 63:32 of the preceeding even indexed 64b register. In this mode all FP code except that built for the plain FP64 ABI can execute correctly. Most notably a combination of FP64A & FP32 code can execute correctly, allowing for existing FP32 binaries to be linked with new FP64A binaries that can make use of 64 bit FP & MSA. Hybrid FPRs are implemented by setting both the FR & FRE bits, trapping & emulating single precision FP instructions (via Reserved Instruction exceptions) whilst allowing others to execute natively. It therefore has a penalty in terms of execution speed, and should only be used when no fully native mode can be. As more binaries are recompiled to use either the FPXX or FP64(A) ABIs, the need for hybrid FPRs should diminish. However in the short to mid term it allows for a gradual transition towards that world, rather than a complete ABI break which is not feasible for some users & not desirable for many. A task will be executed using the hybrid FPR scheme when its TIF_HYBRID_FPREGS flag is set & TIF_32BIT_FPREGS is clear. A further patch will set the flags as necessary, this patch simply adds the infrastructure necessary for the hybrid FPR mode to work. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: linux-fsdevel@vger.kernel.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/7683/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2014-09-11 11:30:20 +04:00
/*
* We can't allow the emulated instruction to leave any of
* the cause bits set in $fcr31.
*/
current->thread.fpu.fcr31 &= ~FPU_CSR_ALL_X;
MIPS: Support for hybrid FPRs Hybrid FPRs is a scheme where scalar FP registers are 64b wide, but accesses to odd indexed single registers use bits 63:32 of the preceeding even indexed 64b register. In this mode all FP code except that built for the plain FP64 ABI can execute correctly. Most notably a combination of FP64A & FP32 code can execute correctly, allowing for existing FP32 binaries to be linked with new FP64A binaries that can make use of 64 bit FP & MSA. Hybrid FPRs are implemented by setting both the FR & FRE bits, trapping & emulating single precision FP instructions (via Reserved Instruction exceptions) whilst allowing others to execute natively. It therefore has a penalty in terms of execution speed, and should only be used when no fully native mode can be. As more binaries are recompiled to use either the FPXX or FP64(A) ABIs, the need for hybrid FPRs should diminish. However in the short to mid term it allows for a gradual transition towards that world, rather than a complete ABI break which is not feasible for some users & not desirable for many. A task will be executed using the hybrid FPR scheme when its TIF_HYBRID_FPREGS flag is set & TIF_32BIT_FPREGS is clear. A further patch will set the flags as necessary, this patch simply adds the infrastructure necessary for the hybrid FPR mode to work. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: linux-fsdevel@vger.kernel.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/7683/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2014-09-11 11:30:20 +04:00
/* Restore the hardware register state */
own_fpu(1);
/* Send a signal if required. */
process_fpemu_return(sig, fault_addr, fcr31);
MIPS: Support for hybrid FPRs Hybrid FPRs is a scheme where scalar FP registers are 64b wide, but accesses to odd indexed single registers use bits 63:32 of the preceeding even indexed 64b register. In this mode all FP code except that built for the plain FP64 ABI can execute correctly. Most notably a combination of FP64A & FP32 code can execute correctly, allowing for existing FP32 binaries to be linked with new FP64A binaries that can make use of 64 bit FP & MSA. Hybrid FPRs are implemented by setting both the FR & FRE bits, trapping & emulating single precision FP instructions (via Reserved Instruction exceptions) whilst allowing others to execute natively. It therefore has a penalty in terms of execution speed, and should only be used when no fully native mode can be. As more binaries are recompiled to use either the FPXX or FP64(A) ABIs, the need for hybrid FPRs should diminish. However in the short to mid term it allows for a gradual transition towards that world, rather than a complete ABI break which is not feasible for some users & not desirable for many. A task will be executed using the hybrid FPR scheme when its TIF_HYBRID_FPREGS flag is set & TIF_32BIT_FPREGS is clear. A further patch will set the flags as necessary, this patch simply adds the infrastructure necessary for the hybrid FPR mode to work. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: linux-fsdevel@vger.kernel.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/7683/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2014-09-11 11:30:20 +04:00
return 0;
}
/*
* XXX Delayed fp exceptions when doing a lazy ctx switch XXX
*/
asmlinkage void do_fpe(struct pt_regs *regs, unsigned long fcr31)
{
enum ctx_state prev_state;
void __user *fault_addr;
int sig;
prev_state = exception_enter();
if (notify_die(DIE_FP, "FP exception", regs, 0, regs_to_trapnr(regs),
SIGFPE) == NOTIFY_STOP)
goto out;
MIPS: Clear [MSA]FPE CSR.Cause after notify_die() When handling floating point exceptions (FPEs) and MSA FPEs the Cause bits of the appropriate control and status register (FCSR for FPEs and MSACSR for MSA FPEs) are read and cleared before enabling interrupts, presumably so that it doesn't have to go through the pain of restoring those bits if the process is pre-empted, since writing those bits would cause another immediate exception while still in the kernel. The bits aren't normally ever restored again, since userland never expects to see them set. However for virtualisation it is necessary for the kernel to be able to restore these Cause bits, as the guest may have been interrupted in an FP exception handler but before it could read the Cause bits. This can be done by registering a die notifier, to get notified of the exception when such a value is restored, and if the PC was at the instruction which is used to restore the guest state, the handler can step over it and continue execution. The Cause bits can then remain set without causing further exceptions. For this to work safely a few changes are made: - __build_clear_fpe and __build_clear_msa_fpe no longer clear the Cause bits, and now return from exception level with interrupts disabled instead of enabled. - do_fpe() now clears the Cause bits and enables interrupts after notify_die() is called, so that the notifier can chose to return from exception without this happening. - do_msa_fpe() acts similarly, but now actually makes use of the second argument (msacsr) and calls notify_die() with the new DIE_MSAFP, allowing die notifiers to be informed of MSA FPEs too. Signed-off-by: James Hogan <james.hogan@imgtec.com> Acked-by: Ralf Baechle <ralf@linux-mips.org> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Gleb Natapov <gleb@kernel.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org
2014-12-02 16:44:13 +03:00
/* Clear FCSR.Cause before enabling interrupts */
write_32bit_cp1_register(CP1_STATUS, fcr31 & ~FPU_CSR_ALL_X);
local_irq_enable();
die_if_kernel("FP exception in kernel code", regs);
if (fcr31 & FPU_CSR_UNI_X) {
/*
* Unimplemented operation exception. If we've got the full
* software emulator on-board, let's use it...
*
* Force FPU to dump state into task/thread context. We're
* moving a lot of data here for what is probably a single
* instruction, but the alternative is to pre-decode the FP
* register operands before invoking the emulator, which seems
* a bit extreme for what should be an infrequent event.
*/
/* Ensure 'resume' not overwrite saved fp context again. */
lose_fpu(1);
/* Run the emulator */
sig = fpu_emulator_cop1Handler(regs, &current->thread.fpu, 1,
&fault_addr);
fcr31 = current->thread.fpu.fcr31;
/*
* We can't allow the emulated instruction to leave any of
* the cause bits set in $fcr31.
*/
current->thread.fpu.fcr31 &= ~FPU_CSR_ALL_X;
/* Restore the hardware register state */
own_fpu(1); /* Using the FPU again. */
} else {
sig = SIGFPE;
fault_addr = (void __user *) regs->cp0_epc;
}
/* Send a signal if required. */
process_fpemu_return(sig, fault_addr, fcr31);
out:
exception_exit(prev_state);
}
void do_trap_or_bp(struct pt_regs *regs, unsigned int code,
const char *str)
{
siginfo_t info;
char b[40];
#ifdef CONFIG_KGDB_LOW_LEVEL_TRAP
if (kgdb_ll_trap(DIE_TRAP, str, regs, code, regs_to_trapnr(regs), SIGTRAP) == NOTIFY_STOP)
return;
#endif /* CONFIG_KGDB_LOW_LEVEL_TRAP */
if (notify_die(DIE_TRAP, str, regs, code, regs_to_trapnr(regs),
SIGTRAP) == NOTIFY_STOP)
return;
/*
* A short test says that IRIX 5.3 sends SIGTRAP for all trap
* insns, even for trap and break codes that indicate arithmetic
* failures. Weird ...
* But should we continue the brokenness??? --macro
*/
switch (code) {
case BRK_OVERFLOW:
case BRK_DIVZERO:
scnprintf(b, sizeof(b), "%s instruction in kernel code", str);
die_if_kernel(b, regs);
if (code == BRK_DIVZERO)
info.si_code = FPE_INTDIV;
else
info.si_code = FPE_INTOVF;
info.si_signo = SIGFPE;
info.si_errno = 0;
info.si_addr = (void __user *) regs->cp0_epc;
force_sig_info(SIGFPE, &info, current);
break;
case BRK_BUG:
die_if_kernel("Kernel bug detected", regs);
force_sig(SIGTRAP, current);
break;
case BRK_MEMU:
/*
* This breakpoint code is used by the FPU emulator to retake
* control of the CPU after executing the instruction from the
* delay slot of an emulated branch.
*
* Terminate if exception was recognized as a delay slot return
* otherwise handle as normal.
*/
if (do_dsemulret(regs))
return;
die_if_kernel("Math emu break/trap", regs);
force_sig(SIGTRAP, current);
break;
default:
scnprintf(b, sizeof(b), "%s instruction in kernel code", str);
die_if_kernel(b, regs);
force_sig(SIGTRAP, current);
}
}
asmlinkage void do_bp(struct pt_regs *regs)
{
unsigned long epc = msk_isa16_mode(exception_epc(regs));
unsigned int opcode, bcode;
enum ctx_state prev_state;
mm_segment_t seg;
seg = get_fs();
if (!user_mode(regs))
set_fs(KERNEL_DS);
prev_state = exception_enter();
if (get_isa16_mode(regs->cp0_epc)) {
u16 instr[2];
if (__get_user(instr[0], (u16 __user *)epc))
goto out_sigsegv;
if (!cpu_has_mmips) {
/* MIPS16e mode */
bcode = (instr[0] >> 5) & 0x3f;
} else if (mm_insn_16bit(instr[0])) {
/* 16-bit microMIPS BREAK */
bcode = instr[0] & 0xf;
} else {
/* 32-bit microMIPS BREAK */
if (__get_user(instr[1], (u16 __user *)(epc + 2)))
goto out_sigsegv;
opcode = (instr[0] << 16) | instr[1];
bcode = (opcode >> 6) & ((1 << 20) - 1);
}
} else {
if (__get_user(opcode, (unsigned int __user *)epc))
goto out_sigsegv;
bcode = (opcode >> 6) & ((1 << 20) - 1);
}
/*
* There is the ancient bug in the MIPS assemblers that the break
* code starts left to bit 16 instead to bit 6 in the opcode.
* Gas is bug-compatible, but not always, grrr...
* We handle both cases with a simple heuristics. --macro
*/
if (bcode >= (1 << 10))
bcode = ((bcode & ((1 << 10) - 1)) << 10) | (bcode >> 10);
/*
* notify the kprobe handlers, if instruction is likely to
* pertain to them.
*/
switch (bcode) {
case BRK_KPROBE_BP:
if (notify_die(DIE_BREAK, "debug", regs, bcode,
regs_to_trapnr(regs), SIGTRAP) == NOTIFY_STOP)
goto out;
else
break;
case BRK_KPROBE_SSTEPBP:
if (notify_die(DIE_SSTEPBP, "single_step", regs, bcode,
regs_to_trapnr(regs), SIGTRAP) == NOTIFY_STOP)
goto out;
else
break;
default:
break;
}
do_trap_or_bp(regs, bcode, "Break");
out:
set_fs(seg);
exception_exit(prev_state);
return;
out_sigsegv:
force_sig(SIGSEGV, current);
goto out;
}
asmlinkage void do_tr(struct pt_regs *regs)
{
u32 opcode, tcode = 0;
enum ctx_state prev_state;
u16 instr[2];
mm_segment_t seg;
unsigned long epc = msk_isa16_mode(exception_epc(regs));
seg = get_fs();
if (!user_mode(regs))
set_fs(get_ds());
prev_state = exception_enter();
if (get_isa16_mode(regs->cp0_epc)) {
if (__get_user(instr[0], (u16 __user *)(epc + 0)) ||
__get_user(instr[1], (u16 __user *)(epc + 2)))
goto out_sigsegv;
opcode = (instr[0] << 16) | instr[1];
/* Immediate versions don't provide a code. */
if (!(opcode & OPCODE))
tcode = (opcode >> 12) & ((1 << 4) - 1);
} else {
if (__get_user(opcode, (u32 __user *)epc))
goto out_sigsegv;
/* Immediate versions don't provide a code. */
if (!(opcode & OPCODE))
tcode = (opcode >> 6) & ((1 << 10) - 1);
}
do_trap_or_bp(regs, tcode, "Trap");
out:
set_fs(seg);
exception_exit(prev_state);
return;
out_sigsegv:
force_sig(SIGSEGV, current);
goto out;
}
asmlinkage void do_ri(struct pt_regs *regs)
{
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
unsigned int __user *epc = (unsigned int __user *)exception_epc(regs);
unsigned long old_epc = regs->cp0_epc;
unsigned long old31 = regs->regs[31];
enum ctx_state prev_state;
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
unsigned int opcode = 0;
int status = -1;
/*
* Avoid any kernel code. Just emulate the R2 instruction
* as quickly as possible.
*/
if (mipsr2_emulation && cpu_has_mips_r6 &&
likely(user_mode(regs)) &&
likely(get_user(opcode, epc) >= 0)) {
unsigned long fcr31 = 0;
status = mipsr2_decoder(regs, opcode, &fcr31);
switch (status) {
case 0:
case SIGEMT:
task_thread_info(current)->r2_emul_return = 1;
return;
case SIGILL:
goto no_r2_instr;
default:
process_fpemu_return(status,
&current->thread.cp0_baduaddr,
fcr31);
task_thread_info(current)->r2_emul_return = 1;
return;
}
}
no_r2_instr:
prev_state = exception_enter();
if (notify_die(DIE_RI, "RI Fault", regs, 0, regs_to_trapnr(regs),
SIGILL) == NOTIFY_STOP)
goto out;
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
die_if_kernel("Reserved instruction in kernel code", regs);
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
if (unlikely(compute_return_epc(regs) < 0))
goto out;
if (get_isa16_mode(regs->cp0_epc)) {
unsigned short mmop[2] = { 0 };
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
if (unlikely(get_user(mmop[0], epc) < 0))
status = SIGSEGV;
if (unlikely(get_user(mmop[1], epc) < 0))
status = SIGSEGV;
opcode = (mmop[0] << 16) | mmop[1];
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
if (status < 0)
status = simulate_rdhwr_mm(regs, opcode);
} else {
if (unlikely(get_user(opcode, epc) < 0))
status = SIGSEGV;
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
if (!cpu_has_llsc && status < 0)
status = simulate_llsc(regs, opcode);
if (status < 0)
status = simulate_rdhwr_normal(regs, opcode);
if (status < 0)
status = simulate_sync(regs, opcode);
MIPS: Support for hybrid FPRs Hybrid FPRs is a scheme where scalar FP registers are 64b wide, but accesses to odd indexed single registers use bits 63:32 of the preceeding even indexed 64b register. In this mode all FP code except that built for the plain FP64 ABI can execute correctly. Most notably a combination of FP64A & FP32 code can execute correctly, allowing for existing FP32 binaries to be linked with new FP64A binaries that can make use of 64 bit FP & MSA. Hybrid FPRs are implemented by setting both the FR & FRE bits, trapping & emulating single precision FP instructions (via Reserved Instruction exceptions) whilst allowing others to execute natively. It therefore has a penalty in terms of execution speed, and should only be used when no fully native mode can be. As more binaries are recompiled to use either the FPXX or FP64(A) ABIs, the need for hybrid FPRs should diminish. However in the short to mid term it allows for a gradual transition towards that world, rather than a complete ABI break which is not feasible for some users & not desirable for many. A task will be executed using the hybrid FPR scheme when its TIF_HYBRID_FPREGS flag is set & TIF_32BIT_FPREGS is clear. A further patch will set the flags as necessary, this patch simply adds the infrastructure necessary for the hybrid FPR mode to work. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: linux-fsdevel@vger.kernel.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/7683/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2014-09-11 11:30:20 +04:00
if (status < 0)
status = simulate_fp(regs, opcode, old_epc, old31);
}
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
if (status < 0)
status = SIGILL;
if (unlikely(status > 0)) {
regs->cp0_epc = old_epc; /* Undo skip-over. */
regs->regs[31] = old31;
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
force_sig(status, current);
}
out:
exception_exit(prev_state);
}
/*
* MIPS MT processors may have fewer FPU contexts than CPU threads. If we've
* emulated more than some threshold number of instructions, force migration to
* a "CPU" that has FP support.
*/
static void mt_ase_fp_affinity(void)
{
#ifdef CONFIG_MIPS_MT_FPAFF
if (mt_fpemul_threshold > 0 &&
((current->thread.emulated_fp++ > mt_fpemul_threshold))) {
/*
* If there's no FPU present, or if the application has already
* restricted the allowed set to exclude any CPUs with FPUs,
* we'll skip the procedure.
*/
if (cpumask_intersects(&current->cpus_allowed, &mt_fpu_cpumask)) {
cpumask_t tmask;
current->thread.user_cpus_allowed
= current->cpus_allowed;
cpumask_and(&tmask, &current->cpus_allowed,
&mt_fpu_cpumask);
set_cpus_allowed_ptr(current, &tmask);
set_thread_flag(TIF_FPUBOUND);
}
}
#endif /* CONFIG_MIPS_MT_FPAFF */
}
/*
* No lock; only written during early bootup by CPU 0.
*/
static RAW_NOTIFIER_HEAD(cu2_chain);
int __ref register_cu2_notifier(struct notifier_block *nb)
{
return raw_notifier_chain_register(&cu2_chain, nb);
}
int cu2_notifier_call_chain(unsigned long val, void *v)
{
return raw_notifier_call_chain(&cu2_chain, val, v);
}
static int default_cu2_call(struct notifier_block *nfb, unsigned long action,
void *data)
{
struct pt_regs *regs = data;
die_if_kernel("COP2: Unhandled kernel unaligned access or invalid "
"instruction", regs);
force_sig(SIGILL, current);
return NOTIFY_OK;
}
2015-01-08 15:17:37 +03:00
static int wait_on_fp_mode_switch(atomic_t *p)
{
/*
* The FP mode for this task is currently being switched. That may
* involve modifications to the format of this tasks FP context which
* make it unsafe to proceed with execution for the moment. Instead,
* schedule some other task.
*/
schedule();
return 0;
}
static int enable_restore_fp_context(int msa)
{
int err, was_fpu_owner, prior_msa;
2015-01-08 15:17:37 +03:00
/*
* If an FP mode switch is currently underway, wait for it to
* complete before proceeding.
*/
wait_on_atomic_t(&current->mm->context.fp_mode_switching,
wait_on_fp_mode_switch, TASK_KILLABLE);
if (!used_math()) {
/* First time FP context user. */
preempt_disable();
err = init_fpu();
if (msa && !err) {
enable_msa();
_init_msa_upper();
set_thread_flag(TIF_USEDMSA);
set_thread_flag(TIF_MSA_CTX_LIVE);
}
preempt_enable();
if (!err)
set_used_math();
return err;
}
/*
* This task has formerly used the FP context.
*
* If this thread has no live MSA vector context then we can simply
* restore the scalar FP context. If it has live MSA vector context
* (that is, it has or may have used MSA since last performing a
* function call) then we'll need to restore the vector context. This
* applies even if we're currently only executing a scalar FP
* instruction. This is because if we were to later execute an MSA
* instruction then we'd either have to:
*
* - Restore the vector context & clobber any registers modified by
* scalar FP instructions between now & then.
*
* or
*
* - Not restore the vector context & lose the most significant bits
* of all vector registers.
*
* Neither of those options is acceptable. We cannot restore the least
* significant bits of the registers now & only restore the most
* significant bits later because the most significant bits of any
* vector registers whose aliased FP register is modified now will have
* been zeroed. We'd have no way to know that when restoring the vector
* context & thus may load an outdated value for the most significant
* bits of a vector register.
*/
if (!msa && !thread_msa_context_live())
return own_fpu(1);
/*
* This task is using or has previously used MSA. Thus we require
* that Status.FR == 1.
*/
preempt_disable();
was_fpu_owner = is_fpu_owner();
err = own_fpu_inatomic(0);
if (err)
goto out;
enable_msa();
write_msa_csr(current->thread.fpu.msacsr);
set_thread_flag(TIF_USEDMSA);
/*
* If this is the first time that the task is using MSA and it has
* previously used scalar FP in this time slice then we already nave
* FP context which we shouldn't clobber. We do however need to clear
* the upper 64b of each vector register so that this task has no
* opportunity to see data left behind by another.
*/
prior_msa = test_and_set_thread_flag(TIF_MSA_CTX_LIVE);
if (!prior_msa && was_fpu_owner) {
_init_msa_upper();
goto out;
}
if (!prior_msa) {
/*
* Restore the least significant 64b of each vector register
* from the existing scalar FP context.
*/
_restore_fp(current);
/*
* The task has not formerly used MSA, so clear the upper 64b
* of each vector register such that it cannot see data left
* behind by another task.
*/
_init_msa_upper();
} else {
/* We need to restore the vector context. */
restore_msa(current);
/* Restore the scalar FP control & status register */
if (!was_fpu_owner)
write_32bit_cp1_register(CP1_STATUS,
current->thread.fpu.fcr31);
}
out:
preempt_enable();
return 0;
}
asmlinkage void do_cpu(struct pt_regs *regs)
{
enum ctx_state prev_state;
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
unsigned int __user *epc;
unsigned long old_epc, old31;
void __user *fault_addr;
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
unsigned int opcode;
unsigned long fcr31;
unsigned int cpid;
int status, err;
unsigned long __maybe_unused flags;
int sig;
prev_state = exception_enter();
cpid = (regs->cp0_cause >> CAUSEB_CE) & 3;
if (cpid != 2)
die_if_kernel("do_cpu invoked from kernel context!", regs);
switch (cpid) {
case 0:
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
epc = (unsigned int __user *)exception_epc(regs);
old_epc = regs->cp0_epc;
old31 = regs->regs[31];
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
opcode = 0;
status = -1;
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
if (unlikely(compute_return_epc(regs) < 0))
break;
if (get_isa16_mode(regs->cp0_epc)) {
unsigned short mmop[2] = { 0 };
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
if (unlikely(get_user(mmop[0], epc) < 0))
status = SIGSEGV;
if (unlikely(get_user(mmop[1], epc) < 0))
status = SIGSEGV;
opcode = (mmop[0] << 16) | mmop[1];
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
if (status < 0)
status = simulate_rdhwr_mm(regs, opcode);
} else {
if (unlikely(get_user(opcode, epc) < 0))
status = SIGSEGV;
if (!cpu_has_llsc && status < 0)
status = simulate_llsc(regs, opcode);
if (status < 0)
status = simulate_rdhwr_normal(regs, opcode);
}
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
if (status < 0)
status = SIGILL;
if (unlikely(status > 0)) {
regs->cp0_epc = old_epc; /* Undo skip-over. */
regs->regs[31] = old31;
[MIPS] SYNC emulation for MIPS I processors Userland, including the C library and the dynamic linker, is keen to use the SYNC instruction, even for "generic" MIPS I binaries these days. Which makes it less than useful on MIPS I processors. This change adds the emulation, but as our do_ri() infrastructure was not really prepared to take yet another instruction, I have rewritten it and its callees slightly as follows. Now there is only a single place a possible signal is thrown from. The place is at the end of do_ri(). The instruction word is fetched in do_ri() and passed down to handlers. The handlers are called in sequence and return a result that lets the caller decide upon further processing. If the result is positive, then the handler has picked the instruction, but a signal should be thrown and the result is the signal number. If the result is zero, then the handler has successfully simulated the instruction. If the result is negative, then the handler did not handle the instruction; to make it more obvious the calls do not follow the usual 0/-Exxx result convention they now return -1 instead of -EFAULT. The calculation of the return EPC is now at the beginning. The reason is it is easier to handle it there as emulation callees may modify a register and an instruction may be located in delay slot of a branch whose result depends on the register. It has to be undone if a signal is to be raised, but it is not a problem as this is the slow-path case, and both actions are done in single places now rather than the former being scattered through emulation handlers. The part of do_cpu() being covered follows the changes to do_ri(). Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> ---
2007-10-16 21:43:26 +04:00
force_sig(status, current);
}
break;
MIPS: Handle COP3 Unusable exception as COP1X for FP emulation Our FP emulator is hardcoded for the MIPS IV FP instruction set and does not match the FP ISA with the general ISA. However for the few MIPS IV FP instructions that use the COP1X major opcode it relies on the Coprocessor Unusable exception to be delivered as a COP1 rather than COP3 exception. This includes indexed transfer (LDXC1, etc.) and FP multiply-accumulate (MADD.D, etc.) instructions. All the MIPS I, II, III and IV processors and some newer chips that do not implement the FPU use the COP3 exception however. Therefore I believe the kernel should follow and redirect any COP3 Unusable traps to the emulator unless an actual FPU part or core is present. This is a change that implements it. Any minor opcode encodings that are not recognised as valid FP instructions are rejected by the emulator and will result in a SIGILL signal being delivered as they currently do. We do not support vendor-specific coprocessor 3 implementations supported with MIPS I and MIPS II ISA processors; we never set CP0.Status.CU3. [Ralf: On MIPS IV processors the kernel always enables the XX bit which replaces the CU3 bit off earlier architecture revisions.] If matching between the CPU and the FPU ISA is considered required one day, this can still be done in the emulator itself. I think the CpU exception dispatcher is not the right place to do this anyway, as there are further differences between MIPS I, MIPS II, MIPS III, MIPS IV and MIPS32 FP ISAs. Corresponding explanation of this implementation is included within the change itself. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/project/linux-mips/list/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-03-07 00:28:54 +04:00
case 3:
/*
* The COP3 opcode space and consequently the CP0.Status.CU3
* bit and the CP0.Cause.CE=3 encoding have been removed as
* of the MIPS III ISA. From the MIPS IV and MIPS32r2 ISAs
* up the space has been reused for COP1X instructions, that
* are enabled by the CP0.Status.CU1 bit and consequently
* use the CP0.Cause.CE=1 encoding for Coprocessor Unusable
* exceptions. Some FPU-less processors that implement one
* of these ISAs however use this code erroneously for COP1X
* instructions. Therefore we redirect this trap to the FP
* emulator too.
MIPS: Handle COP3 Unusable exception as COP1X for FP emulation Our FP emulator is hardcoded for the MIPS IV FP instruction set and does not match the FP ISA with the general ISA. However for the few MIPS IV FP instructions that use the COP1X major opcode it relies on the Coprocessor Unusable exception to be delivered as a COP1 rather than COP3 exception. This includes indexed transfer (LDXC1, etc.) and FP multiply-accumulate (MADD.D, etc.) instructions. All the MIPS I, II, III and IV processors and some newer chips that do not implement the FPU use the COP3 exception however. Therefore I believe the kernel should follow and redirect any COP3 Unusable traps to the emulator unless an actual FPU part or core is present. This is a change that implements it. Any minor opcode encodings that are not recognised as valid FP instructions are rejected by the emulator and will result in a SIGILL signal being delivered as they currently do. We do not support vendor-specific coprocessor 3 implementations supported with MIPS I and MIPS II ISA processors; we never set CP0.Status.CU3. [Ralf: On MIPS IV processors the kernel always enables the XX bit which replaces the CU3 bit off earlier architecture revisions.] If matching between the CPU and the FPU ISA is considered required one day, this can still be done in the emulator itself. I think the CpU exception dispatcher is not the right place to do this anyway, as there are further differences between MIPS I, MIPS II, MIPS III, MIPS IV and MIPS32 FP ISAs. Corresponding explanation of this implementation is included within the change itself. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/project/linux-mips/list/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-03-07 00:28:54 +04:00
*/
if (raw_cpu_has_fpu || !cpu_has_mips_4_5_64_r2_r6) {
force_sig(SIGILL, current);
MIPS: Handle COP3 Unusable exception as COP1X for FP emulation Our FP emulator is hardcoded for the MIPS IV FP instruction set and does not match the FP ISA with the general ISA. However for the few MIPS IV FP instructions that use the COP1X major opcode it relies on the Coprocessor Unusable exception to be delivered as a COP1 rather than COP3 exception. This includes indexed transfer (LDXC1, etc.) and FP multiply-accumulate (MADD.D, etc.) instructions. All the MIPS I, II, III and IV processors and some newer chips that do not implement the FPU use the COP3 exception however. Therefore I believe the kernel should follow and redirect any COP3 Unusable traps to the emulator unless an actual FPU part or core is present. This is a change that implements it. Any minor opcode encodings that are not recognised as valid FP instructions are rejected by the emulator and will result in a SIGILL signal being delivered as they currently do. We do not support vendor-specific coprocessor 3 implementations supported with MIPS I and MIPS II ISA processors; we never set CP0.Status.CU3. [Ralf: On MIPS IV processors the kernel always enables the XX bit which replaces the CU3 bit off earlier architecture revisions.] If matching between the CPU and the FPU ISA is considered required one day, this can still be done in the emulator itself. I think the CpU exception dispatcher is not the right place to do this anyway, as there are further differences between MIPS I, MIPS II, MIPS III, MIPS IV and MIPS32 FP ISAs. Corresponding explanation of this implementation is included within the change itself. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/project/linux-mips/list/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-03-07 00:28:54 +04:00
break;
}
MIPS: Handle COP3 Unusable exception as COP1X for FP emulation Our FP emulator is hardcoded for the MIPS IV FP instruction set and does not match the FP ISA with the general ISA. However for the few MIPS IV FP instructions that use the COP1X major opcode it relies on the Coprocessor Unusable exception to be delivered as a COP1 rather than COP3 exception. This includes indexed transfer (LDXC1, etc.) and FP multiply-accumulate (MADD.D, etc.) instructions. All the MIPS I, II, III and IV processors and some newer chips that do not implement the FPU use the COP3 exception however. Therefore I believe the kernel should follow and redirect any COP3 Unusable traps to the emulator unless an actual FPU part or core is present. This is a change that implements it. Any minor opcode encodings that are not recognised as valid FP instructions are rejected by the emulator and will result in a SIGILL signal being delivered as they currently do. We do not support vendor-specific coprocessor 3 implementations supported with MIPS I and MIPS II ISA processors; we never set CP0.Status.CU3. [Ralf: On MIPS IV processors the kernel always enables the XX bit which replaces the CU3 bit off earlier architecture revisions.] If matching between the CPU and the FPU ISA is considered required one day, this can still be done in the emulator itself. I think the CpU exception dispatcher is not the right place to do this anyway, as there are further differences between MIPS I, MIPS II, MIPS III, MIPS IV and MIPS32 FP ISAs. Corresponding explanation of this implementation is included within the change itself. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/project/linux-mips/list/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-03-07 00:28:54 +04:00
/* Fall through. */
case 1:
err = enable_restore_fp_context(0);
if (raw_cpu_has_fpu && !err)
break;
sig = fpu_emulator_cop1Handler(regs, &current->thread.fpu, 0,
&fault_addr);
fcr31 = current->thread.fpu.fcr31;
/*
* We can't allow the emulated instruction to leave
* any of the cause bits set in $fcr31.
*/
current->thread.fpu.fcr31 &= ~FPU_CSR_ALL_X;
/* Send a signal if required. */
if (!process_fpemu_return(sig, fault_addr, fcr31) && !err)
mt_ase_fp_affinity();
break;
case 2:
raw_notifier_call_chain(&cu2_chain, CU2_EXCEPTION, regs);
break;
}
exception_exit(prev_state);
}
MIPS: Clear [MSA]FPE CSR.Cause after notify_die() When handling floating point exceptions (FPEs) and MSA FPEs the Cause bits of the appropriate control and status register (FCSR for FPEs and MSACSR for MSA FPEs) are read and cleared before enabling interrupts, presumably so that it doesn't have to go through the pain of restoring those bits if the process is pre-empted, since writing those bits would cause another immediate exception while still in the kernel. The bits aren't normally ever restored again, since userland never expects to see them set. However for virtualisation it is necessary for the kernel to be able to restore these Cause bits, as the guest may have been interrupted in an FP exception handler but before it could read the Cause bits. This can be done by registering a die notifier, to get notified of the exception when such a value is restored, and if the PC was at the instruction which is used to restore the guest state, the handler can step over it and continue execution. The Cause bits can then remain set without causing further exceptions. For this to work safely a few changes are made: - __build_clear_fpe and __build_clear_msa_fpe no longer clear the Cause bits, and now return from exception level with interrupts disabled instead of enabled. - do_fpe() now clears the Cause bits and enables interrupts after notify_die() is called, so that the notifier can chose to return from exception without this happening. - do_msa_fpe() acts similarly, but now actually makes use of the second argument (msacsr) and calls notify_die() with the new DIE_MSAFP, allowing die notifiers to be informed of MSA FPEs too. Signed-off-by: James Hogan <james.hogan@imgtec.com> Acked-by: Ralf Baechle <ralf@linux-mips.org> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Gleb Natapov <gleb@kernel.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org
2014-12-02 16:44:13 +03:00
asmlinkage void do_msa_fpe(struct pt_regs *regs, unsigned int msacsr)
{
enum ctx_state prev_state;
prev_state = exception_enter();
MIPS: Clear [MSA]FPE CSR.Cause after notify_die() When handling floating point exceptions (FPEs) and MSA FPEs the Cause bits of the appropriate control and status register (FCSR for FPEs and MSACSR for MSA FPEs) are read and cleared before enabling interrupts, presumably so that it doesn't have to go through the pain of restoring those bits if the process is pre-empted, since writing those bits would cause another immediate exception while still in the kernel. The bits aren't normally ever restored again, since userland never expects to see them set. However for virtualisation it is necessary for the kernel to be able to restore these Cause bits, as the guest may have been interrupted in an FP exception handler but before it could read the Cause bits. This can be done by registering a die notifier, to get notified of the exception when such a value is restored, and if the PC was at the instruction which is used to restore the guest state, the handler can step over it and continue execution. The Cause bits can then remain set without causing further exceptions. For this to work safely a few changes are made: - __build_clear_fpe and __build_clear_msa_fpe no longer clear the Cause bits, and now return from exception level with interrupts disabled instead of enabled. - do_fpe() now clears the Cause bits and enables interrupts after notify_die() is called, so that the notifier can chose to return from exception without this happening. - do_msa_fpe() acts similarly, but now actually makes use of the second argument (msacsr) and calls notify_die() with the new DIE_MSAFP, allowing die notifiers to be informed of MSA FPEs too. Signed-off-by: James Hogan <james.hogan@imgtec.com> Acked-by: Ralf Baechle <ralf@linux-mips.org> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Gleb Natapov <gleb@kernel.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org
2014-12-02 16:44:13 +03:00
if (notify_die(DIE_MSAFP, "MSA FP exception", regs, 0,
regs_to_trapnr(regs), SIGFPE) == NOTIFY_STOP)
goto out;
/* Clear MSACSR.Cause before enabling interrupts */
write_msa_csr(msacsr & ~MSA_CSR_CAUSEF);
local_irq_enable();
die_if_kernel("do_msa_fpe invoked from kernel context!", regs);
force_sig(SIGFPE, current);
MIPS: Clear [MSA]FPE CSR.Cause after notify_die() When handling floating point exceptions (FPEs) and MSA FPEs the Cause bits of the appropriate control and status register (FCSR for FPEs and MSACSR for MSA FPEs) are read and cleared before enabling interrupts, presumably so that it doesn't have to go through the pain of restoring those bits if the process is pre-empted, since writing those bits would cause another immediate exception while still in the kernel. The bits aren't normally ever restored again, since userland never expects to see them set. However for virtualisation it is necessary for the kernel to be able to restore these Cause bits, as the guest may have been interrupted in an FP exception handler but before it could read the Cause bits. This can be done by registering a die notifier, to get notified of the exception when such a value is restored, and if the PC was at the instruction which is used to restore the guest state, the handler can step over it and continue execution. The Cause bits can then remain set without causing further exceptions. For this to work safely a few changes are made: - __build_clear_fpe and __build_clear_msa_fpe no longer clear the Cause bits, and now return from exception level with interrupts disabled instead of enabled. - do_fpe() now clears the Cause bits and enables interrupts after notify_die() is called, so that the notifier can chose to return from exception without this happening. - do_msa_fpe() acts similarly, but now actually makes use of the second argument (msacsr) and calls notify_die() with the new DIE_MSAFP, allowing die notifiers to be informed of MSA FPEs too. Signed-off-by: James Hogan <james.hogan@imgtec.com> Acked-by: Ralf Baechle <ralf@linux-mips.org> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Gleb Natapov <gleb@kernel.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org
2014-12-02 16:44:13 +03:00
out:
exception_exit(prev_state);
}
asmlinkage void do_msa(struct pt_regs *regs)
{
enum ctx_state prev_state;
int err;
prev_state = exception_enter();
if (!cpu_has_msa || test_thread_flag(TIF_32BIT_FPREGS)) {
force_sig(SIGILL, current);
goto out;
}
die_if_kernel("do_msa invoked from kernel context!", regs);
err = enable_restore_fp_context(1);
if (err)
force_sig(SIGILL, current);
out:
exception_exit(prev_state);
}
asmlinkage void do_mdmx(struct pt_regs *regs)
{
enum ctx_state prev_state;
prev_state = exception_enter();
force_sig(SIGILL, current);
exception_exit(prev_state);
}
/*
* Called with interrupts disabled.
*/
asmlinkage void do_watch(struct pt_regs *regs)
{
enum ctx_state prev_state;
u32 cause;
prev_state = exception_enter();
/*
* Clear WP (bit 22) bit of cause register so we don't loop
* forever.
*/
cause = read_c0_cause();
cause &= ~(1 << 22);
write_c0_cause(cause);
/*
* If the current thread has the watch registers loaded, save
* their values and send SIGTRAP. Otherwise another thread
* left the registers set, clear them and continue.
*/
if (test_tsk_thread_flag(current, TIF_LOAD_WATCH)) {
mips_read_watch_registers();
local_irq_enable();
force_sig(SIGTRAP, current);
} else {
mips_clear_watch_registers();
local_irq_enable();
}
exception_exit(prev_state);
}
asmlinkage void do_mcheck(struct pt_regs *regs)
{
const int field = 2 * sizeof(unsigned long);
int multi_match = regs->cp0_status & ST0_TS;
enum ctx_state prev_state;
mm_segment_t old_fs = get_fs();
prev_state = exception_enter();
show_regs(regs);
if (multi_match) {
pr_err("Index : %0x\n", read_c0_index());
pr_err("Pagemask: %0x\n", read_c0_pagemask());
pr_err("EntryHi : %0*lx\n", field, read_c0_entryhi());
pr_err("EntryLo0: %0*lx\n", field, read_c0_entrylo0());
pr_err("EntryLo1: %0*lx\n", field, read_c0_entrylo1());
pr_err("Wired : %0x\n", read_c0_wired());
pr_err("Pagegrain: %0x\n", read_c0_pagegrain());
if (cpu_has_htw) {
pr_err("PWField : %0*lx\n", field, read_c0_pwfield());
pr_err("PWSize : %0*lx\n", field, read_c0_pwsize());
pr_err("PWCtl : %0x\n", read_c0_pwctl());
}
pr_err("\n");
dump_tlb_all();
}
if (!user_mode(regs))
set_fs(KERNEL_DS);
show_code((unsigned int __user *) regs->cp0_epc);
set_fs(old_fs);
/*
* Some chips may have other causes of machine check (e.g. SB1
* graduation timer)
*/
panic("Caught Machine Check exception - %scaused by multiple "
"matching entries in the TLB.",
(multi_match) ? "" : "not ");
}
asmlinkage void do_mt(struct pt_regs *regs)
{
int subcode;
subcode = (read_vpe_c0_vpecontrol() & VPECONTROL_EXCPT)
>> VPECONTROL_EXCPT_SHIFT;
switch (subcode) {
case 0:
printk(KERN_DEBUG "Thread Underflow\n");
break;
case 1:
printk(KERN_DEBUG "Thread Overflow\n");
break;
case 2:
printk(KERN_DEBUG "Invalid YIELD Qualifier\n");
break;
case 3:
printk(KERN_DEBUG "Gating Storage Exception\n");
break;
case 4:
printk(KERN_DEBUG "YIELD Scheduler Exception\n");
break;
case 5:
printk(KERN_DEBUG "Gating Storage Scheduler Exception\n");
break;
default:
printk(KERN_DEBUG "*** UNKNOWN THREAD EXCEPTION %d ***\n",
subcode);
break;
}
die_if_kernel("MIPS MT Thread exception in kernel", regs);
force_sig(SIGILL, current);
}
asmlinkage void do_dsp(struct pt_regs *regs)
{
if (cpu_has_dsp)
panic("Unexpected DSP exception");
force_sig(SIGILL, current);
}
asmlinkage void do_reserved(struct pt_regs *regs)
{
/*
* Game over - no way to handle this if it ever occurs. Most probably
* caused by a new unknown cpu type or after another deadly
* hard/software error.
*/
show_regs(regs);
panic("Caught reserved exception %ld - should not happen.",
(regs->cp0_cause & 0x7f) >> 2);
}
static int __initdata l1parity = 1;
static int __init nol1parity(char *s)
{
l1parity = 0;
return 1;
}
__setup("nol1par", nol1parity);
static int __initdata l2parity = 1;
static int __init nol2parity(char *s)
{
l2parity = 0;
return 1;
}
__setup("nol2par", nol2parity);
/*
* Some MIPS CPUs can enable/disable for cache parity detection, but do
* it different ways.
*/
static inline void parity_protection_init(void)
{
switch (current_cpu_type()) {
case CPU_24K:
case CPU_34K:
case CPU_74K:
case CPU_1004K:
case CPU_1074K:
case CPU_INTERAPTIV:
case CPU_PROAPTIV:
case CPU_P5600:
case CPU_QEMU_GENERIC:
{
#define ERRCTL_PE 0x80000000
#define ERRCTL_L2P 0x00800000
unsigned long errctl;
unsigned int l1parity_present, l2parity_present;
errctl = read_c0_ecc();
errctl &= ~(ERRCTL_PE|ERRCTL_L2P);
/* probe L1 parity support */
write_c0_ecc(errctl | ERRCTL_PE);
back_to_back_c0_hazard();
l1parity_present = (read_c0_ecc() & ERRCTL_PE);
/* probe L2 parity support */
write_c0_ecc(errctl|ERRCTL_L2P);
back_to_back_c0_hazard();
l2parity_present = (read_c0_ecc() & ERRCTL_L2P);
if (l1parity_present && l2parity_present) {
if (l1parity)
errctl |= ERRCTL_PE;
if (l1parity ^ l2parity)
errctl |= ERRCTL_L2P;
} else if (l1parity_present) {
if (l1parity)
errctl |= ERRCTL_PE;
} else if (l2parity_present) {
if (l2parity)
errctl |= ERRCTL_L2P;
} else {
/* No parity available */
}
printk(KERN_INFO "Writing ErrCtl register=%08lx\n", errctl);
write_c0_ecc(errctl);
back_to_back_c0_hazard();
errctl = read_c0_ecc();
printk(KERN_INFO "Readback ErrCtl register=%08lx\n", errctl);
if (l1parity_present)
printk(KERN_INFO "Cache parity protection %sabled\n",
(errctl & ERRCTL_PE) ? "en" : "dis");
if (l2parity_present) {
if (l1parity_present && l1parity)
errctl ^= ERRCTL_L2P;
printk(KERN_INFO "L2 cache parity protection %sabled\n",
(errctl & ERRCTL_L2P) ? "en" : "dis");
}
}
break;
case CPU_5KC:
case CPU_5KE:
case CPU_LOONGSON1:
write_c0_ecc(0x80000000);
back_to_back_c0_hazard();
/* Set the PE bit (bit 31) in the c0_errctl register. */
printk(KERN_INFO "Cache parity protection %sabled\n",
(read_c0_ecc() & 0x80000000) ? "en" : "dis");
break;
case CPU_20KC:
case CPU_25KF:
/* Clear the DE bit (bit 16) in the c0_status register. */
printk(KERN_INFO "Enable cache parity protection for "
"MIPS 20KC/25KF CPUs.\n");
clear_c0_status(ST0_DE);
break;
default:
break;
}
}
asmlinkage void cache_parity_error(void)
{
const int field = 2 * sizeof(unsigned long);
unsigned int reg_val;
/* For the moment, report the problem and hang. */
printk("Cache error exception:\n");
printk("cp0_errorepc == %0*lx\n", field, read_c0_errorepc());
reg_val = read_c0_cacheerr();
printk("c0_cacheerr == %08x\n", reg_val);
printk("Decoded c0_cacheerr: %s cache fault in %s reference.\n",
reg_val & (1<<30) ? "secondary" : "primary",
reg_val & (1<<31) ? "data" : "insn");
if ((cpu_has_mips_r2_r6) &&
((current_cpu_data.processor_id & 0xff0000) == PRID_COMP_MIPS)) {
pr_err("Error bits: %s%s%s%s%s%s%s%s\n",
reg_val & (1<<29) ? "ED " : "",
reg_val & (1<<28) ? "ET " : "",
reg_val & (1<<27) ? "ES " : "",
reg_val & (1<<26) ? "EE " : "",
reg_val & (1<<25) ? "EB " : "",
reg_val & (1<<24) ? "EI " : "",
reg_val & (1<<23) ? "E1 " : "",
reg_val & (1<<22) ? "E0 " : "");
} else {
pr_err("Error bits: %s%s%s%s%s%s%s\n",
reg_val & (1<<29) ? "ED " : "",
reg_val & (1<<28) ? "ET " : "",
reg_val & (1<<26) ? "EE " : "",
reg_val & (1<<25) ? "EB " : "",
reg_val & (1<<24) ? "EI " : "",
reg_val & (1<<23) ? "E1 " : "",
reg_val & (1<<22) ? "E0 " : "");
}
printk("IDX: 0x%08x\n", reg_val & ((1<<22)-1));
#if defined(CONFIG_CPU_MIPS32) || defined(CONFIG_CPU_MIPS64)
if (reg_val & (1<<22))
printk("DErrAddr0: 0x%0*lx\n", field, read_c0_derraddr0());
if (reg_val & (1<<23))
printk("DErrAddr1: 0x%0*lx\n", field, read_c0_derraddr1());
#endif
panic("Can't handle the cache error!");
}
asmlinkage void do_ftlb(void)
{
const int field = 2 * sizeof(unsigned long);
unsigned int reg_val;
/* For the moment, report the problem and hang. */
if ((cpu_has_mips_r2_r6) &&
((current_cpu_data.processor_id & 0xff0000) == PRID_COMP_MIPS)) {
pr_err("FTLB error exception, cp0_ecc=0x%08x:\n",
read_c0_ecc());
pr_err("cp0_errorepc == %0*lx\n", field, read_c0_errorepc());
reg_val = read_c0_cacheerr();
pr_err("c0_cacheerr == %08x\n", reg_val);
if ((reg_val & 0xc0000000) == 0xc0000000) {
pr_err("Decoded c0_cacheerr: FTLB parity error\n");
} else {
pr_err("Decoded c0_cacheerr: %s cache fault in %s reference.\n",
reg_val & (1<<30) ? "secondary" : "primary",
reg_val & (1<<31) ? "data" : "insn");
}
} else {
pr_err("FTLB error exception\n");
}
/* Just print the cacheerr bits for now */
cache_parity_error();
}
/*
* SDBBP EJTAG debug exception handler.
* We skip the instruction and return to the next instruction.
*/
void ejtag_exception_handler(struct pt_regs *regs)
{
const int field = 2 * sizeof(unsigned long);
unsigned long depc, old_epc, old_ra;
unsigned int debug;
printk(KERN_DEBUG "SDBBP EJTAG debug exception - not handled yet, just ignored!\n");
depc = read_c0_depc();
debug = read_c0_debug();
printk(KERN_DEBUG "c0_depc = %0*lx, DEBUG = %08x\n", field, depc, debug);
if (debug & 0x80000000) {
/*
* In branch delay slot.
* We cheat a little bit here and use EPC to calculate the
* debug return address (DEPC). EPC is restored after the
* calculation.
*/
old_epc = regs->cp0_epc;
old_ra = regs->regs[31];
regs->cp0_epc = depc;
compute_return_epc(regs);
depc = regs->cp0_epc;
regs->cp0_epc = old_epc;
regs->regs[31] = old_ra;
} else
depc += 4;
write_c0_depc(depc);
#if 0
printk(KERN_DEBUG "\n\n----- Enable EJTAG single stepping ----\n\n");
write_c0_debug(debug | 0x100);
#endif
}
/*
* NMI exception handler.
* No lock; only written during early bootup by CPU 0.
*/
static RAW_NOTIFIER_HEAD(nmi_chain);
int register_nmi_notifier(struct notifier_block *nb)
{
return raw_notifier_chain_register(&nmi_chain, nb);
}
void __noreturn nmi_exception_handler(struct pt_regs *regs)
{
char str[100];
raw_notifier_call_chain(&nmi_chain, 0, regs);
bust_spinlocks(1);
snprintf(str, 100, "CPU%d NMI taken, CP0_EPC=%lx\n",
smp_processor_id(), regs->cp0_epc);
regs->cp0_epc = read_c0_errorepc();
die(str, regs);
}
#define VECTORSPACING 0x100 /* for EI/VI mode */
unsigned long ebase;
unsigned long exception_handlers[32];
unsigned long vi_handlers[64];
void __init *set_except_vector(int n, void *addr)
{
unsigned long handler = (unsigned long) addr;
unsigned long old_handler;
#ifdef CONFIG_CPU_MICROMIPS
/*
* Only the TLB handlers are cache aligned with an even
* address. All other handlers are on an odd address and
* require no modification. Otherwise, MIPS32 mode will
* be entered when handling any TLB exceptions. That
* would be bad...since we must stay in microMIPS mode.
*/
if (!(handler & 0x1))
handler |= 1;
#endif
old_handler = xchg(&exception_handlers[n], handler);
if (n == 0 && cpu_has_divec) {
#ifdef CONFIG_CPU_MICROMIPS
unsigned long jump_mask = ~((1 << 27) - 1);
#else
unsigned long jump_mask = ~((1 << 28) - 1);
#endif
u32 *buf = (u32 *)(ebase + 0x200);
unsigned int k0 = 26;
if ((handler & jump_mask) == ((ebase + 0x200) & jump_mask)) {
uasm_i_j(&buf, handler & ~jump_mask);
uasm_i_nop(&buf);
} else {
UASM_i_LA(&buf, k0, handler);
uasm_i_jr(&buf, k0);
uasm_i_nop(&buf);
}
local_flush_icache_range(ebase + 0x200, (unsigned long)buf);
}
return (void *)old_handler;
}
MIPS: Make tlb exception handler definitions and declarations match. The code was written as it is because it's more expressive, a bit easier. But it's always been dirty, if not a bug. But we can't cheat with LTO compilers, so this results in: [...] LDFINAL vmlinux.o In file included from arch/mips/kernel/topology.c:604:0, from arch/mips/kernel/time.c:212, from arch/mips/kernel/syscall.c:300, from arch/mips/kernel/signal.c:853, from arch/mips/kernel/setup.c:1030, from arch/mips/kernel/reset.c:354, from arch/mips/kernel/ptrace.c:562, from arch/mips/kernel/process.c:770, from arch/mips/kernel/irq.c:350, from arch/mips/kernel/branch.c:321, from arch/mips/kernel/cpu-probe.c:1370, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:345, from arch/mips/sgi-ip22/ip22-gio.c:660, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/sgialib.h:219, from arch/mips/sgi-ip22/ip22-reset.c:224, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/paccess.h:116, from arch/mips/sgi-ip22/ip22-nvram.c:334, from include/linux/kernel_stat.h:79, from arch/mips/sgi-ip22/ip22-int.c:592, from arch/mips/sgi-ip22/ip22-hpc.c:470, from arch/mips/sgi-ip22/ip22-mc.c:135, from init/init_task.c:54, from init/calibrate.c:744, from init/noinitramfs.c:62, from init/do_mounts.c:573, from init/version.c:1009, from init/main.c:777, from :729: arch/mips/kernel/traps.c:63:49: error: variable ‘handle_tlbl’ redeclared as function In file included from arch/mips/mm/page.c:310:0, from arch/mips/mm/mmap.c:208, from arch/mips/mm/init.c:641, from arch/mips/mm/gup.c:811, from arch/mips/mm/fault.c:659, from include/linux/module.h:682, from arch/mips/mm/dma-default.c:161, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:397, from arch/mips/kernel/i8253.c:538, from arch/mips/kernel/proc.c:145, from arch/mips/kernel/irq_cpu.c:129, from arch/mips/kernel/i8259.c:229, from include/uapi/linux/elf.h:251, from arch/mips/kernel/mips_ksyms.c:129, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/time.h:50, from arch/mips/kernel/cevt-r4k.c:90, from arch/mips/kernel/vdso.c:136, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:351, from arch/mips/kernel/unaligned.c:809, from arch/mips/kernel/traps.c:1720, from arch/mips/kernel/topology.c:684, from arch/mips/kernel/time.c:212, from arch/mips/kernel/syscall.c:300, from arch/mips/kernel/signal.c:853, from arch/mips/kernel/setup.c:1030, from arch/mips/kernel/reset.c:354, from arch/mips/kernel/ptrace.c:562, from arch/mips/kernel/process.c:770, from arch/mips/kernel/irq.c:350, from arch/mips/kernel/branch.c:321, from arch/mips/kernel/cpu-probe.c:1370, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:345, from arch/mips/sgi-ip22/ip22-gio.c:660, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/sgialib.h:219, from arch/mips/sgi-ip22/ip22-reset.c:224, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/paccess.h:116, from arch/mips/sgi-ip22/ip22-nvram.c:334, from include/linux/kernel_stat.h:79, from arch/mips/sgi-ip22/ip22-int.c:592, from arch/mips/sgi-ip22/ip22-hpc.c:470, from arch/mips/sgi-ip22/ip22-mc.c:135, from init/init_task.c:54, from init/calibrate.c:744, from init/noinitramfs.c:62, from init/do_mounts.c:573, from init/version.c:1009, from init/main.c:777, from :729: arch/mips/mm/tlbex.c:1448:5: note: previously declared here In file included from arch/mips/kernel/topology.c:604:0, from arch/mips/kernel/time.c:212, from arch/mips/kernel/syscall.c:300, from arch/mips/kernel/signal.c:853, from arch/mips/kernel/setup.c:1030, from arch/mips/kernel/reset.c:354, from arch/mips/kernel/ptrace.c:562, from arch/mips/kernel/process.c:770, from arch/mips/kernel/irq.c:350, from arch/mips/kernel/branch.c:321, from arch/mips/kernel/cpu-probe.c:1370, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:345, from arch/mips/sgi-ip22/ip22-gio.c:660, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/sgialib.h:219, from arch/mips/sgi-ip22/ip22-reset.c:224, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/paccess.h:116, from arch/mips/sgi-ip22/ip22-nvram.c:334, from include/linux/kernel_stat.h:79, from arch/mips/sgi-ip22/ip22-int.c:592, from arch/mips/sgi-ip22/ip22-hpc.c:470, from arch/mips/sgi-ip22/ip22-mc.c:135, from init/init_task.c:54, from init/calibrate.c:744, from init/noinitramfs.c:62, from init/do_mounts.c:573, from init/version.c:1009, from init/main.c:777, from :729: arch/mips/kernel/traps.c:62:49: error: variable ‘handle_tlbm’ redeclared as function In file included from arch/mips/mm/page.c:310:0, from arch/mips/mm/mmap.c:208, from arch/mips/mm/init.c:641, from arch/mips/mm/gup.c:811, from arch/mips/mm/fault.c:659, from include/linux/module.h:682, from arch/mips/mm/dma-default.c:161, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:397, from arch/mips/kernel/i8253.c:538, from arch/mips/kernel/proc.c:145, from arch/mips/kernel/irq_cpu.c:129, from arch/mips/kernel/i8259.c:229, from include/uapi/linux/elf.h:251, from arch/mips/kernel/mips_ksyms.c:129, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/time.h:50, from arch/mips/kernel/cevt-r4k.c:90, from arch/mips/kernel/vdso.c:136, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:351, from arch/mips/kernel/unaligned.c:809, from arch/mips/kernel/traps.c:1720, from arch/mips/kernel/topology.c:684, from arch/mips/kernel/time.c:212, from arch/mips/kernel/syscall.c:300, from arch/mips/kernel/signal.c:853, from arch/mips/kernel/setup.c:1030, from arch/mips/kernel/reset.c:354, from arch/mips/kernel/ptrace.c:562, from arch/mips/kernel/process.c:770, from arch/mips/kernel/irq.c:350, from arch/mips/kernel/branch.c:321, from arch/mips/kernel/cpu-probe.c:1370, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:345, from arch/mips/sgi-ip22/ip22-gio.c:660, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/sgialib.h:219, from arch/mips/sgi-ip22/ip22-reset.c:224, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/paccess.h:116, from arch/mips/sgi-ip22/ip22-nvram.c:334, from include/linux/kernel_stat.h:79, from arch/mips/sgi-ip22/ip22-int.c:592, from arch/mips/sgi-ip22/ip22-hpc.c:470, from arch/mips/sgi-ip22/ip22-mc.c:135, from init/init_task.c:54, from init/calibrate.c:744, from init/noinitramfs.c:62, from init/do_mounts.c:573, from init/version.c:1009, from init/main.c:777, from :729: arch/mips/mm/tlbex.c:1450:5: note: previously declared here In file included from arch/mips/kernel/topology.c:604:0, from arch/mips/kernel/time.c:212, from arch/mips/kernel/syscall.c:300, from arch/mips/kernel/signal.c:853, from arch/mips/kernel/setup.c:1030, from arch/mips/kernel/reset.c:354, from arch/mips/kernel/ptrace.c:562, from arch/mips/kernel/process.c:770, from arch/mips/kernel/irq.c:350, from arch/mips/kernel/branch.c:321, from arch/mips/kernel/cpu-probe.c:1370, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:345, from arch/mips/sgi-ip22/ip22-gio.c:660, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/sgialib.h:219, from arch/mips/sgi-ip22/ip22-reset.c:224, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/paccess.h:116, from arch/mips/sgi-ip22/ip22-nvram.c:334, from include/linux/kernel_stat.h:79, from arch/mips/sgi-ip22/ip22-int.c:592, from arch/mips/sgi-ip22/ip22-hpc.c:470, from arch/mips/sgi-ip22/ip22-mc.c:135, from init/init_task.c:54, from init/calibrate.c:744, from init/noinitramfs.c:62, from init/do_mounts.c:573, from init/version.c:1009, from init/main.c:777, from :729: arch/mips/kernel/traps.c:64:49: error: variable ‘handle_tlbs’ redeclared as function In file included from arch/mips/mm/page.c:310:0, from arch/mips/mm/mmap.c:208, from arch/mips/mm/init.c:641, from arch/mips/mm/gup.c:811, from arch/mips/mm/fault.c:659, from include/linux/module.h:682, from arch/mips/mm/dma-default.c:161, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:397, from arch/mips/kernel/i8253.c:538, from arch/mips/kernel/proc.c:145, from arch/mips/kernel/irq_cpu.c:129, from arch/mips/kernel/i8259.c:229, from include/uapi/linux/elf.h:251, from arch/mips/kernel/mips_ksyms.c:129, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/time.h:50, from arch/mips/kernel/cevt-r4k.c:90, from arch/mips/kernel/vdso.c:136, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:351, from arch/mips/kernel/unaligned.c:809, from arch/mips/kernel/traps.c:1720, from arch/mips/kernel/topology.c:684, from arch/mips/kernel/time.c:212, from arch/mips/kernel/syscall.c:300, from arch/mips/kernel/signal.c:853, from arch/mips/kernel/setup.c:1030, from arch/mips/kernel/reset.c:354, from arch/mips/kernel/ptrace.c:562, from arch/mips/kernel/process.c:770, from arch/mips/kernel/irq.c:350, from arch/mips/kernel/branch.c:321, from arch/mips/kernel/cpu-probe.c:1370, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/thread_info.h:345, from arch/mips/sgi-ip22/ip22-gio.c:660, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/sgialib.h:219, from arch/mips/sgi-ip22/ip22-reset.c:224, from /fluff/home/ralf/src/linux/lto/linux-misc/arch/mips/include/asm/paccess.h:116, from arch/mips/sgi-ip22/ip22-nvram.c:334, from include/linux/kernel_stat.h:79, from arch/mips/sgi-ip22/ip22-int.c:592, from arch/mips/sgi-ip22/ip22-hpc.c:470, from arch/mips/sgi-ip22/ip22-mc.c:135, from init/init_task.c:54, from init/calibrate.c:744, from init/noinitramfs.c:62, from init/do_mounts.c:573, from init/version.c:1009, from init/main.c:777, from :729: arch/mips/mm/tlbex.c:1449:5: note: previously declared here lto1: fatal error: errors during merging of translation units compilation terminated. lto-wrapper: /usr/bin/mips-linux-gcc returned 1 exit status /usr/lib64/gcc/mips-linux/4.7.1/../../../../mips-linux/bin/ld: lto-wrapper failed collect2: error: ld returned 1 exit status make: *** [vmlinux] Error 1 Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2013-02-08 04:21:34 +04:00
static void do_default_vi(void)
{
show_regs(get_irq_regs());
panic("Caught unexpected vectored interrupt.");
}
static void *set_vi_srs_handler(int n, vi_handler_t addr, int srs)
{
unsigned long handler;
unsigned long old_handler = vi_handlers[n];
int srssets = current_cpu_data.srsets;
u16 *h;
unsigned char *b;
BUG_ON(!cpu_has_veic && !cpu_has_vint);
if (addr == NULL) {
handler = (unsigned long) do_default_vi;
srs = 0;
} else
handler = (unsigned long) addr;
vi_handlers[n] = handler;
b = (unsigned char *)(ebase + 0x200 + n*VECTORSPACING);
if (srs >= srssets)
panic("Shadow register set %d not supported", srs);
if (cpu_has_veic) {
if (board_bind_eic_interrupt)
board_bind_eic_interrupt(n, srs);
} else if (cpu_has_vint) {
/* SRSMap is only defined if shadow sets are implemented */
if (srssets > 1)
change_c0_srsmap(0xf << n*4, srs << n*4);
}
if (srs == 0) {
/*
* If no shadow set is selected then use the default handler
* that does normal register saving and standard interrupt exit
*/
extern char except_vec_vi, except_vec_vi_lui;
extern char except_vec_vi_ori, except_vec_vi_end;
extern char rollback_except_vec_vi;
char *vec_start = using_rollback_handler() ?
&rollback_except_vec_vi : &except_vec_vi;
#if defined(CONFIG_CPU_MICROMIPS) || defined(CONFIG_CPU_BIG_ENDIAN)
const int lui_offset = &except_vec_vi_lui - vec_start + 2;
const int ori_offset = &except_vec_vi_ori - vec_start + 2;
#else
const int lui_offset = &except_vec_vi_lui - vec_start;
const int ori_offset = &except_vec_vi_ori - vec_start;
#endif
const int handler_len = &except_vec_vi_end - vec_start;
if (handler_len > VECTORSPACING) {
/*
* Sigh... panicing won't help as the console
* is probably not configured :(
*/
panic("VECTORSPACING too small");
}
set_handler(((unsigned long)b - ebase), vec_start,
#ifdef CONFIG_CPU_MICROMIPS
(handler_len - 1));
#else
handler_len);
#endif
h = (u16 *)(b + lui_offset);
*h = (handler >> 16) & 0xffff;
h = (u16 *)(b + ori_offset);
*h = (handler & 0xffff);
local_flush_icache_range((unsigned long)b,
(unsigned long)(b+handler_len));
}
else {
/*
* In other cases jump directly to the interrupt handler. It
* is the handler's responsibility to save registers if required
* (eg hi/lo) and return from the exception using "eret".
*/
u32 insn;
h = (u16 *)b;
/* j handler */
#ifdef CONFIG_CPU_MICROMIPS
insn = 0xd4000000 | (((u32)handler & 0x07ffffff) >> 1);
#else
insn = 0x08000000 | (((u32)handler & 0x0fffffff) >> 2);
#endif
h[0] = (insn >> 16) & 0xffff;
h[1] = insn & 0xffff;
h[2] = 0;
h[3] = 0;
local_flush_icache_range((unsigned long)b,
(unsigned long)(b+8));
}
return (void *)old_handler;
}
void *set_vi_handler(int n, vi_handler_t addr)
{
return set_vi_srs_handler(n, addr, 0);
}
extern void tlb_init(void);
/*
* Timer interrupt
*/
int cp0_compare_irq;
EXPORT_SYMBOL_GPL(cp0_compare_irq);
int cp0_compare_irq_shift;
/*
* Performance counter IRQ or -1 if shared with timer
*/
int cp0_perfcount_irq;
EXPORT_SYMBOL_GPL(cp0_perfcount_irq);
/*
* Fast debug channel IRQ or -1 if not present
*/
int cp0_fdc_irq;
EXPORT_SYMBOL_GPL(cp0_fdc_irq);
MIPS: Delete __cpuinit/__CPUINIT usage from MIPS code commit 3747069b25e419f6b51395f48127e9812abc3596 upstream. The __cpuinit type of throwaway sections might have made sense some time ago when RAM was more constrained, but now the savings do not offset the cost and complications. For example, the fix in commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time") is a good example of the nasty type of bugs that can be created with improper use of the various __init prefixes. After a discussion on LKML[1] it was decided that cpuinit should go the way of devinit and be phased out. Once all the users are gone, we can then finally remove the macros themselves from linux/init.h. Note that some harmless section mismatch warnings may result, since notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c) and are flagged as __cpuinit -- so if we remove the __cpuinit from the arch specific callers, we will also get section mismatch warnings. As an intermediate step, we intend to turn the linux/init.h cpuinit related content into no-ops as early as possible, since that will get rid of these warnings. In any case, they are temporary and harmless. Here, we remove all the MIPS __cpuinit from C code and __CPUINIT from asm files. MIPS is interesting in this respect, because there are also uasm users hiding behind their own renamed versions of the __cpuinit macros. [1] https://lkml.org/lkml/2013/5/20/589 [ralf@linux-mips.org: Folded in Paul's followup fix.] Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5494/ Patchwork: https://patchwork.linux-mips.org/patch/5495/ Patchwork: https://patchwork.linux-mips.org/patch/5509/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2013-06-18 17:38:59 +04:00
static int noulri;
static int __init ulri_disable(char *s)
{
pr_info("Disabling ulri\n");
noulri = 1;
return 1;
}
__setup("noulri", ulri_disable);
/* configure STATUS register */
static void configure_status(void)
{
/*
* Disable coprocessors and select 32-bit or 64-bit addressing
* and the 16/32 or 32/32 FPR register model. Reset the BEV
* flag that some firmware may have left set and the TS bit (for
* IP27). Set XX for ISA IV code to work.
*/
unsigned int status_set = ST0_CU0;
#ifdef CONFIG_64BIT
status_set |= ST0_FR|ST0_KX|ST0_SX|ST0_UX;
#endif
if (current_cpu_data.isa_level & MIPS_CPU_ISA_IV)
status_set |= ST0_XX;
if (cpu_has_dsp)
status_set |= ST0_MX;
change_c0_status(ST0_CU|ST0_MX|ST0_RE|ST0_FR|ST0_BEV|ST0_TS|ST0_KX|ST0_SX|ST0_UX,
status_set);
}
/* configure HWRENA register */
static void configure_hwrena(void)
{
unsigned int hwrena = cpu_hwrena_impl_bits;
if (cpu_has_mips_r2_r6)
hwrena |= 0x0000000f;
if (!noulri && cpu_has_userlocal)
hwrena |= (1 << 29);
if (hwrena)
write_c0_hwrena(hwrena);
}
static void configure_exception_vector(void)
{
if (cpu_has_veic || cpu_has_vint) {
unsigned long sr = set_c0_status(ST0_BEV);
write_c0_ebase(ebase);
write_c0_status(sr);
/* Setting vector spacing enables EI/VI mode */
change_c0_intctl(0x3e0, VECTORSPACING);
}
if (cpu_has_divec) {
if (cpu_has_mipsmt) {
unsigned int vpflags = dvpe();
set_c0_cause(CAUSEF_IV);
evpe(vpflags);
} else
set_c0_cause(CAUSEF_IV);
}
}
void per_cpu_trap_init(bool is_boot_cpu)
{
unsigned int cpu = smp_processor_id();
configure_status();
configure_hwrena();
configure_exception_vector();
/*
* Before R2 both interrupt numbers were fixed to 7, so on R2 only:
*
* o read IntCtl.IPTI to determine the timer interrupt
* o read IntCtl.IPPCI to determine the performance counter interrupt
* o read IntCtl.IPFDC to determine the fast debug channel interrupt
*/
if (cpu_has_mips_r2_r6) {
cp0_compare_irq_shift = CAUSEB_TI - CAUSEB_IP;
cp0_compare_irq = (read_c0_intctl() >> INTCTLB_IPTI) & 7;
cp0_perfcount_irq = (read_c0_intctl() >> INTCTLB_IPPCI) & 7;
cp0_fdc_irq = (read_c0_intctl() >> INTCTLB_IPFDC) & 7;
if (!cp0_fdc_irq)
cp0_fdc_irq = -1;
} else {
cp0_compare_irq = CP0_LEGACY_COMPARE_IRQ;
cp0_compare_irq_shift = CP0_LEGACY_PERFCNT_IRQ;
cp0_perfcount_irq = -1;
cp0_fdc_irq = -1;
}
if (!cpu_data[cpu].asid_cache)
cpu_data[cpu].asid_cache = ASID_FIRST_VERSION;
atomic_inc(&init_mm.mm_count);
current->active_mm = &init_mm;
BUG_ON(current->mm);
enter_lazy_tlb(&init_mm, current);
/* Boot CPU's cache setup in setup_arch(). */
if (!is_boot_cpu)
cpu_cache_init();
tlb_init();
TLBMISS_HANDLER_SETUP();
}
/* Install CPU exception handler */
MIPS: Delete __cpuinit/__CPUINIT usage from MIPS code commit 3747069b25e419f6b51395f48127e9812abc3596 upstream. The __cpuinit type of throwaway sections might have made sense some time ago when RAM was more constrained, but now the savings do not offset the cost and complications. For example, the fix in commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time") is a good example of the nasty type of bugs that can be created with improper use of the various __init prefixes. After a discussion on LKML[1] it was decided that cpuinit should go the way of devinit and be phased out. Once all the users are gone, we can then finally remove the macros themselves from linux/init.h. Note that some harmless section mismatch warnings may result, since notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c) and are flagged as __cpuinit -- so if we remove the __cpuinit from the arch specific callers, we will also get section mismatch warnings. As an intermediate step, we intend to turn the linux/init.h cpuinit related content into no-ops as early as possible, since that will get rid of these warnings. In any case, they are temporary and harmless. Here, we remove all the MIPS __cpuinit from C code and __CPUINIT from asm files. MIPS is interesting in this respect, because there are also uasm users hiding behind their own renamed versions of the __cpuinit macros. [1] https://lkml.org/lkml/2013/5/20/589 [ralf@linux-mips.org: Folded in Paul's followup fix.] Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5494/ Patchwork: https://patchwork.linux-mips.org/patch/5495/ Patchwork: https://patchwork.linux-mips.org/patch/5509/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2013-06-18 17:38:59 +04:00
void set_handler(unsigned long offset, void *addr, unsigned long size)
{
#ifdef CONFIG_CPU_MICROMIPS
memcpy((void *)(ebase + offset), ((unsigned char *)addr - 1), size);
#else
memcpy((void *)(ebase + offset), addr, size);
#endif
local_flush_icache_range(ebase + offset, ebase + offset + size);
}
MIPS: Delete __cpuinit/__CPUINIT usage from MIPS code commit 3747069b25e419f6b51395f48127e9812abc3596 upstream. The __cpuinit type of throwaway sections might have made sense some time ago when RAM was more constrained, but now the savings do not offset the cost and complications. For example, the fix in commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time") is a good example of the nasty type of bugs that can be created with improper use of the various __init prefixes. After a discussion on LKML[1] it was decided that cpuinit should go the way of devinit and be phased out. Once all the users are gone, we can then finally remove the macros themselves from linux/init.h. Note that some harmless section mismatch warnings may result, since notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c) and are flagged as __cpuinit -- so if we remove the __cpuinit from the arch specific callers, we will also get section mismatch warnings. As an intermediate step, we intend to turn the linux/init.h cpuinit related content into no-ops as early as possible, since that will get rid of these warnings. In any case, they are temporary and harmless. Here, we remove all the MIPS __cpuinit from C code and __CPUINIT from asm files. MIPS is interesting in this respect, because there are also uasm users hiding behind their own renamed versions of the __cpuinit macros. [1] https://lkml.org/lkml/2013/5/20/589 [ralf@linux-mips.org: Folded in Paul's followup fix.] Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5494/ Patchwork: https://patchwork.linux-mips.org/patch/5495/ Patchwork: https://patchwork.linux-mips.org/patch/5509/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2013-06-18 17:38:59 +04:00
static char panic_null_cerr[] =
"Trying to set NULL cache error exception handler";
/*
* Install uncached CPU exception handler.
* This is suitable only for the cache error exception which is the only
* exception handler that is being run uncached.
*/
MIPS: Delete __cpuinit/__CPUINIT usage from MIPS code commit 3747069b25e419f6b51395f48127e9812abc3596 upstream. The __cpuinit type of throwaway sections might have made sense some time ago when RAM was more constrained, but now the savings do not offset the cost and complications. For example, the fix in commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time") is a good example of the nasty type of bugs that can be created with improper use of the various __init prefixes. After a discussion on LKML[1] it was decided that cpuinit should go the way of devinit and be phased out. Once all the users are gone, we can then finally remove the macros themselves from linux/init.h. Note that some harmless section mismatch warnings may result, since notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c) and are flagged as __cpuinit -- so if we remove the __cpuinit from the arch specific callers, we will also get section mismatch warnings. As an intermediate step, we intend to turn the linux/init.h cpuinit related content into no-ops as early as possible, since that will get rid of these warnings. In any case, they are temporary and harmless. Here, we remove all the MIPS __cpuinit from C code and __CPUINIT from asm files. MIPS is interesting in this respect, because there are also uasm users hiding behind their own renamed versions of the __cpuinit macros. [1] https://lkml.org/lkml/2013/5/20/589 [ralf@linux-mips.org: Folded in Paul's followup fix.] Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5494/ Patchwork: https://patchwork.linux-mips.org/patch/5495/ Patchwork: https://patchwork.linux-mips.org/patch/5509/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2013-06-18 17:38:59 +04:00
void set_uncached_handler(unsigned long offset, void *addr,
unsigned long size)
{
unsigned long uncached_ebase = CKSEG1ADDR(ebase);
if (!addr)
panic(panic_null_cerr);
memcpy((void *)(uncached_ebase + offset), addr, size);
}
static int __initdata rdhwr_noopt;
static int __init set_rdhwr_noopt(char *str)
{
rdhwr_noopt = 1;
return 1;
}
__setup("rdhwr_noopt", set_rdhwr_noopt);
void __init trap_init(void)
{
extern char except_vec3_generic;
extern char except_vec4;
extern char except_vec3_r4000;
unsigned long i;
check_wait();
if (cpu_has_veic || cpu_has_vint) {
unsigned long size = 0x200 + VECTORSPACING*64;
ebase = (unsigned long)
__alloc_bootmem(size, 1 << fls(size), 0);
} else {
#ifdef CONFIG_KVM_GUEST
#define KVM_GUEST_KSEG0 0x40000000
ebase = KVM_GUEST_KSEG0;
#else
ebase = CKSEG0;
#endif
if (cpu_has_mips_r2_r6)
ebase += (read_c0_ebase() & 0x3ffff000);
}
if (cpu_has_mmips) {
unsigned int config3 = read_c0_config3();
if (IS_ENABLED(CONFIG_CPU_MICROMIPS))
write_c0_config3(config3 | MIPS_CONF3_ISA_OE);
else
write_c0_config3(config3 & ~MIPS_CONF3_ISA_OE);
}
if (board_ebase_setup)
board_ebase_setup();
per_cpu_trap_init(true);
/*
* Copy the generic exception handlers to their final destination.
* This will be overriden later as suitable for a particular
* configuration.
*/
set_handler(0x180, &except_vec3_generic, 0x80);
/*
* Setup default vectors
*/
for (i = 0; i <= 31; i++)
set_except_vector(i, handle_reserved);
/*
* Copy the EJTAG debug exception vector handler code to it's final
* destination.
*/
if (cpu_has_ejtag && board_ejtag_handler_setup)
board_ejtag_handler_setup();
/*
* Only some CPUs have the watch exceptions.
*/
if (cpu_has_watch)
set_except_vector(23, handle_watch);
/*
* Initialise interrupt handlers
*/
if (cpu_has_veic || cpu_has_vint) {
int nvec = cpu_has_veic ? 64 : 8;
for (i = 0; i < nvec; i++)
set_vi_handler(i, NULL);
}
else if (cpu_has_divec)
set_handler(0x200, &except_vec4, 0x8);
/*
* Some CPUs can enable/disable for cache parity detection, but does
* it different ways.
*/
parity_protection_init();
/*
* The Data Bus Errors / Instruction Bus Errors are signaled
* by external hardware. Therefore these two exceptions
* may have board specific handlers.
*/
if (board_be_init)
board_be_init();
set_except_vector(0, using_rollback_handler() ? rollback_handle_int
: handle_int);
set_except_vector(1, handle_tlbm);
set_except_vector(2, handle_tlbl);
set_except_vector(3, handle_tlbs);
set_except_vector(4, handle_adel);
set_except_vector(5, handle_ades);
set_except_vector(6, handle_ibe);
set_except_vector(7, handle_dbe);
set_except_vector(8, handle_sys);
set_except_vector(9, handle_bp);
set_except_vector(10, rdhwr_noopt ? handle_ri :
(cpu_has_vtag_icache ?
handle_ri_rdhwr_vivt : handle_ri_rdhwr));
set_except_vector(11, handle_cpu);
set_except_vector(12, handle_ov);
set_except_vector(13, handle_tr);
set_except_vector(14, handle_msa_fpe);
if (current_cpu_type() == CPU_R6000 ||
current_cpu_type() == CPU_R6000A) {
/*
* The R6000 is the only R-series CPU that features a machine
* check exception (similar to the R4000 cache error) and
* unaligned ldc1/sdc1 exception. The handlers have not been
* written yet. Well, anyway there is no R6000 machine on the
* current list of targets for Linux/MIPS.
* (Duh, crap, there is someone with a triple R6k machine)
*/
//set_except_vector(14, handle_mc);
//set_except_vector(15, handle_ndc);
}
if (board_nmi_handler_setup)
board_nmi_handler_setup();
if (cpu_has_fpu && !cpu_has_nofpuex)
set_except_vector(15, handle_fpe);
set_except_vector(16, handle_ftlb);
if (cpu_has_rixiex) {
set_except_vector(19, tlb_do_page_fault_0);
set_except_vector(20, tlb_do_page_fault_0);
}
set_except_vector(21, handle_msa);
set_except_vector(22, handle_mdmx);
if (cpu_has_mcheck)
set_except_vector(24, handle_mcheck);
if (cpu_has_mipsmt)
set_except_vector(25, handle_mt);
set_except_vector(26, handle_dsp);
if (board_cache_error_setup)
board_cache_error_setup();
if (cpu_has_vce)
/* Special exception: R4[04]00 uses also the divec space. */
set_handler(0x180, &except_vec3_r4000, 0x100);
else if (cpu_has_4kex)
set_handler(0x180, &except_vec3_generic, 0x80);
else
set_handler(0x080, &except_vec3_generic, 0x80);
local_flush_icache_range(ebase, ebase + 0x400);
sort_extable(__start___dbe_table, __stop___dbe_table);
cu2_notifier(default_cu2_call, 0x80000000); /* Run last */
}
static int trap_pm_notifier(struct notifier_block *self, unsigned long cmd,
void *v)
{
switch (cmd) {
case CPU_PM_ENTER_FAILED:
case CPU_PM_EXIT:
configure_status();
configure_hwrena();
configure_exception_vector();
/* Restore register with CPU number for TLB handlers */
TLBMISS_HANDLER_RESTORE();
break;
}
return NOTIFY_OK;
}
static struct notifier_block trap_pm_notifier_block = {
.notifier_call = trap_pm_notifier,
};
static int __init trap_pm_init(void)
{
return cpu_pm_register_notifier(&trap_pm_notifier_block);
}
arch_initcall(trap_pm_init);