linux/arch/arm/mach-imx/mach-imx6q.c

/*
 * Copyright 2011-2013 Freescale Semiconductor, Inc.
 * Copyright 2011 Linaro Ltd.
 *
 * The code contained herein is licensed under the GNU General Public
 * License. You may obtain a copy of the GNU General Public License
 * Version 2 or later at the following locations:
 *
 * http://www.opensource.org/licenses/gpl-license.html
 * http://www.gnu.org/copyleft/gpl.html
 */

#include <linux/clk.h>
#include <linux/clkdev.h>
#include <linux/cpu.h>
#include <linux/delay.h>
#include <linux/export.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/irqchip.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
#include <linux/of_platform.h>
#include <linux/pm_opp.h>
#include <linux/pci.h>
#include <linux/phy.h>
#include <linux/reboot.h>
#include <linux/regmap.h>
#include <linux/micrel_phy.h>
#include <linux/mfd/syscon.h>
#include <linux/mfd/syscon/imx6q-iomuxc-gpr.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/system_misc.h>

#include "common.h"
#include "cpuidle.h"
#include "hardware.h"

/* For imx6q sabrelite board: set KSZ9021RN RGMII pad skew */
static int ksz9021rn_phy_fixup(struct phy_device *phydev)
{
	if (IS_BUILTIN(CONFIG_PHYLIB)) {
		/* min rx data delay */
		phy_write(phydev, MICREL_KSZ9021_EXTREG_CTRL,
			0x8000 | MICREL_KSZ9021_RGMII_RX_DATA_PAD_SCEW);
		phy_write(phydev, MICREL_KSZ9021_EXTREG_DATA_WRITE, 0x0000);

		/* max rx/tx clock delay, min rx/tx control delay */
		phy_write(phydev, MICREL_KSZ9021_EXTREG_CTRL,
			0x8000 | MICREL_KSZ9021_RGMII_CLK_CTRL_PAD_SCEW);
		phy_write(phydev, MICREL_KSZ9021_EXTREG_DATA_WRITE, 0xf0f0);
		phy_write(phydev, MICREL_KSZ9021_EXTREG_CTRL,
			MICREL_KSZ9021_RGMII_CLK_CTRL_PAD_SCEW);
	}

	return 0;
}

static void mmd_write_reg(struct phy_device *dev, int device, int reg, int val)
{
	phy_write(dev, 0x0d, device);
	phy_write(dev, 0x0e, reg);
	phy_write(dev, 0x0d, (1 << 14) | device);
	phy_write(dev, 0x0e, val);
}

static int ksz9031rn_phy_fixup(struct phy_device *dev)
{
	/*
	 * min rx data delay, max rx/tx clock delay,
	 * min rx/tx control delay
	 */
	mmd_write_reg(dev, 2, 4, 0);
	mmd_write_reg(dev, 2, 5, 0);
	mmd_write_reg(dev, 2, 8, 0x003ff);

	return 0;
}

/*
 * fixup for PLX PEX8909 bridge to configure GPIO1-7 as output High
 * as they are used for slots1-7 PERST#
 */
static void ventana_pciesw_early_fixup(struct pci_dev *dev)
{
	u32 dw;

	if (!of_machine_is_compatible("gw,ventana"))
		return;

	if (dev->devfn != 0)
		return;

	pci_read_config_dword(dev, 0x62c, &dw);
	dw |= 0xaaa8; // GPIO1-7 outputs
	pci_write_config_dword(dev, 0x62c, dw);

	pci_read_config_dword(dev, 0x644, &dw);
	dw |= 0xfe;   // GPIO1-7 output high
	pci_write_config_dword(dev, 0x644, dw);

	msleep(100);
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_PLX, 0x8609, ventana_pciesw_early_fixup);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_PLX, 0x8606, ventana_pciesw_early_fixup);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_PLX, 0x8604, ventana_pciesw_early_fixup);

static int ar8031_phy_fixup(struct phy_device *dev)
{
	u16 val;

	/* To enable AR8031 output a 125MHz clk from CLK_25M */
	phy_write(dev, 0xd, 0x7);
	phy_write(dev, 0xe, 0x8016);
	phy_write(dev, 0xd, 0x4007);

	val = phy_read(dev, 0xe);
	val &= 0xffe3;
	val |= 0x18;
	phy_write(dev, 0xe, val);

	/* introduce tx clock delay */
	phy_write(dev, 0x1d, 0x5);
	val = phy_read(dev, 0x1e);
	val |= 0x0100;
	phy_write(dev, 0x1e, val);

	return 0;
}

#define PHY_ID_AR8031	0x004dd074

static int ar8035_phy_fixup(struct phy_device *dev)
{
	u16 val;

	/* Ar803x phy SmartEEE feature cause link status generates glitch,
	 * which cause ethernet link down/up issue, so disable SmartEEE
	 */
	phy_write(dev, 0xd, 0x3);
	phy_write(dev, 0xe, 0x805d);
	phy_write(dev, 0xd, 0x4003);

	val = phy_read(dev, 0xe);
	phy_write(dev, 0xe, val & ~(1 << 8));

	/*
	 * Enable 125MHz clock from CLK_25M on the AR8031.  This
	 * is fed in to the IMX6 on the ENET_REF_CLK (V22) pad.
	 * Also, introduce a tx clock delay.
	 *
	 * This is the same as is the AR8031 fixup.
	 */
	ar8031_phy_fixup(dev);

	/*check phy power*/
	val = phy_read(dev, 0x0);
	if (val & BMCR_PDOWN)
		phy_write(dev, 0x0, val & ~BMCR_PDOWN);

	return 0;
}

#define PHY_ID_AR8035 0x004dd072

static void __init imx6q_enet_phy_init(void)
{
	if (IS_BUILTIN(CONFIG_PHYLIB)) {
		phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK,
				ksz9021rn_phy_fixup);
		phy_register_fixup_for_uid(PHY_ID_KSZ9031, MICREL_PHY_ID_MASK,
				ksz9031rn_phy_fixup);
		phy_register_fixup_for_uid(PHY_ID_AR8031, 0xffffffff,
				ar8031_phy_fixup);
		phy_register_fixup_for_uid(PHY_ID_AR8035, 0xffffffef,
				ar8035_phy_fixup);
	}
}

static void __init imx6q_1588_init(void)
{
	struct regmap *gpr;

	gpr = syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr");
	if (!IS_ERR(gpr))
		regmap_update_bits(gpr, IOMUXC_GPR1,
				IMX6Q_GPR1_ENET_CLK_SEL_MASK,
				IMX6Q_GPR1_ENET_CLK_SEL_ANATOP);
	else
		pr_err("failed to find fsl,imx6q-iomux-gpr regmap\n");

}

static void __init imx6q_init_machine(void)
{
	struct device *parent;

	imx_print_silicon_rev(cpu_is_imx6dl() ? "i.MX6DL" : "i.MX6Q",
			      imx_get_soc_revision());

	mxc_arch_reset_init_dt();

	parent = imx_soc_device_init();
	if (parent == NULL)
		pr_warn("failed to initialize soc device\n");

	imx6q_enet_phy_init();

	of_platform_populate(NULL, of_default_bus_match_table, NULL, parent);

	imx_anatop_init();
	cpu_is_imx6q() ?  imx6q_pm_init() : imx6dl_pm_init();
	imx6q_1588_init();
}

#define OCOTP_CFG3			0x440
#define OCOTP_CFG3_SPEED_SHIFT		16
#define OCOTP_CFG3_SPEED_1P2GHZ		0x3

static void __init imx6q_opp_check_1p2ghz(struct device *cpu_dev)
{
	struct device_node *np;
	void __iomem *base;
	u32 val;

	np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-ocotp");
	if (!np) {
		pr_warn("failed to find ocotp node\n");
		return;
	}

	base = of_iomap(np, 0);
	if (!base) {
		pr_warn("failed to map ocotp\n");
		goto put_node;
	}

	val = readl_relaxed(base + OCOTP_CFG3);
	val >>= OCOTP_CFG3_SPEED_SHIFT;
	if ((val & 0x3) != OCOTP_CFG3_SPEED_1P2GHZ)
		if (dev_pm_opp_disable(cpu_dev, 1200000000))
			pr_warn("failed to disable 1.2 GHz OPP\n");

put_node:
	of_node_put(np);
}

static void __init imx6q_opp_init(void)
{
	struct device_node *np;
	struct device *cpu_dev = get_cpu_device(0);

	if (!cpu_dev) {
		pr_warn("failed to get cpu0 device\n");
		return;
	}
	np = of_node_get(cpu_dev->of_node);
	if (!np) {
		pr_warn("failed to find cpu0 node\n");
		return;
	}

	if (of_init_opp_table(cpu_dev)) {
		pr_warn("failed to init OPP table\n");
		goto put_node;
	}

	imx6q_opp_check_1p2ghz(cpu_dev);

put_node:
	of_node_put(np);
}

static struct platform_device imx6q_cpufreq_pdev = {
	.name = "imx6q-cpufreq",
};

static void __init imx6q_init_late(void)
{
	/*
	 * WAIT mode is broken on TO 1.0 and 1.1, so there is no point
	 * to run cpuidle on them.
	 */
	if (imx_get_soc_revision() > IMX_CHIP_REVISION_1_1)
		imx6q_cpuidle_init();

	if (IS_ENABLED(CONFIG_ARM_IMX6Q_CPUFREQ)) {
		imx6q_opp_init();
		platform_device_register(&imx6q_cpufreq_pdev);
	}
}

static void __init imx6q_map_io(void)
{
	debug_ll_io_init();
	imx_scu_map_io();
}

static void __init imx6q_init_irq(void)
{
	imx_init_revision_from_anatop();
	imx_init_l2cache();
	imx_src_init();
	imx_gpc_init();
	irqchip_init();
}

static const char *imx6q_dt_compat[] __initconst = {
	"fsl,imx6dl",
	"fsl,imx6q",
	NULL,
};

DT_MACHINE_START(IMX6Q, "Freescale i.MX6 Quad/DualLite (Device Tree)")
	.smp		= smp_ops(imx_smp_ops),
	.map_io		= imx6q_map_io,
	.init_irq	= imx6q_init_irq,
	.init_machine	= imx6q_init_machine,
	.init_late      = imx6q_init_late,
	.dt_compat	= imx6q_dt_compat,
	.restart	= mxc_restart,
MACHINE_END