IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit e14d7dfb41f5807a0c1c26a13f2b8ef16af24935 upstream.
Jan has noticed that pte_pfn and co. resp. pfn_pte are incorrect for
CONFIG_PAE because phys_addr_t is wider than unsigned long and so the
pte_val reps. shift left would get truncated. Fix this up by using proper
types.
Fixes: 6b28baca9b1f ("x86/speculation/l1tf: Protect PROT_NONE PTEs against speculation")
Reported-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d0f6249058834ffe1ceaad0bb31464af66f6e7a upstream.
The PAE 3-level paging code currently doesn't mitigate L1TF by flipping the
offset bits, and uses the high PTE word, thus bits 32-36 for type, 37-63 for
offset. The lower word is zeroed, thus systems with less than 4GB memory are
safe. With 4GB to 128GB the swap type selects the memory locations vulnerable
to L1TF; with even more memory, also the swap offfset influences the address.
This might be a problem with 32bit PAE guests running on large 64bit hosts.
By continuing to keep the whole swap entry in either high or low 32bit word of
PTE we would limit the swap size too much. Thus this patch uses the whole PAE
PTE with the same layout as the 64bit version does. The macros just become a
bit tricky since they assume the arch-dependent swp_entry_t to be 32bit.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ce2f0393ea2396142b7faf6ee9b1f3676d08a5f upstream.
The TOPOEXT reenablement is a workaround for broken BIOSen which didn't
enable the CPUID bit. amd_get_topology_early(), however, relies on
that bit being set so that it can read out the CPUID leaf and set
smp_num_siblings properly.
Move the reenablement up to early_init_amd(). While at it, simplify
amd_get_topology_early().
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11e34e64e4103955fc4568750914c75d65ea87ee upstream.
336996-Speculative-Execution-Side-Channel-Mitigations.pdf defines a new MSR
(IA32_FLUSH_CMD) which is detected by CPUID.7.EDX[28]=1 bit being set.
This new MSR "gives software a way to invalidate structures with finer
granularity than other architectual methods like WBINVD."
A copy of this document is available at
https://bugzilla.kernel.org/show_bug.cgi?id=199511
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a7ed1ba4bba6c075d5ad61bb75e3fbc870840d6 upstream.
The previous patch has limited swap file size so that large offsets cannot
clear bits above MAX_PA/2 in the pte and interfere with L1TF mitigation.
It assumed that offsets are encoded starting with bit 12, same as pfn. But
on x86_64, offsets are encoded starting with bit 9.
Thus the limit can be raised by 3 bits. That means 16TB with 42bit MAX_PA
and 256TB with 46bit MAX_PA.
Fixes: 377eeaa8e11f ("x86/speculation/l1tf: Limit swap file size to MAX_PA/2")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2207def700f902f169fc237b717252c326f9e464 upstream.
nosmt on the kernel command line merely prevents the onlining of the
secondary SMT siblings.
nosmt=force makes the APIC detection code ignore the secondary SMT siblings
completely, so they even do not show up as possible CPUs. That reduces the
amount of memory allocations for per cpu variables and saves other
resources from being allocated too large.
This is not fully equivalent to disabling SMT in the BIOS because the low
level SMT enabling in the BIOS can result in partitioning of resources
between the siblings, which is not undone by just ignoring them. Some CPUs
can use the full resources when their sibling is not onlined, but this is
depending on the CPU family and model and it's not well documented whether
this applies to all partitioned resources. That means depending on the
workload disabling SMT in the BIOS might result in better performance.
Linus analysis of the Intel manual:
The intel optimization manual is not very clear on what the partitioning
rules are.
I find:
"In general, the buffers for staging instructions between major pipe
stages are partitioned. These buffers include µop queues after the
execution trace cache, the queues after the register rename stage, the
reorder buffer which stages instructions for retirement, and the load
and store buffers.
In the case of load and store buffers, partitioning also provided an
easier implementation to maintain memory ordering for each logical
processor and detect memory ordering violations"
but some of that partitioning may be relaxed if the HT thread is "not
active":
"In Intel microarchitecture code name Sandy Bridge, the micro-op queue
is statically partitioned to provide 28 entries for each logical
processor, irrespective of software executing in single thread or
multiple threads. If one logical processor is not active in Intel
microarchitecture code name Ivy Bridge, then a single thread executing
on that processor core can use the 56 entries in the micro-op queue"
but I do not know what "not active" means, and how dynamic it is. Some of
that partitioning may be entirely static and depend on the early BIOS
disabling of HT, and even if we park the cores, the resources will just be
wasted.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e1d7e25fd759eddf96d8ab39d0a90a1979b2d8c upstream.
To support force disabling of SMT it's required to know the number of
thread siblings early. amd_get_topology() cannot be called before the APIC
driver is selected, so split out the part which initializes
smp_num_siblings and invoke it from amd_early_init().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 119bff8a9c9bb00116a844ec68be7bc4b1c768f5 upstream.
Old code used to check whether CPUID ext max level is >= 0x80000008 because
that last leaf contains the number of cores of the physical CPU. The three
functions called there now do not depend on that leaf anymore so the check
can go.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1910ad5624968f93be48e8e265513c54d66b897c upstream.
Make use of the new early detection function to initialize smp_num_siblings
on the boot cpu before the MP-Table or ACPI/MADT scan happens. That's
required for force disabling SMT.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95f3d39ccf7aaea79d1ffdac1c887c2e100ec1b6 upstream.
To support force disabling of SMT it's required to know the number of
thread siblings early. detect_extended_topology() cannot be called before
the APIC driver is selected, so split out the part which initializes
smp_num_siblings.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 545401f4448a807b963ff17b575e0a393e68b523 upstream.
To support force disabling of SMT it's required to know the number of
thread siblings early. detect_ht() cannot be called before the APIC driver
is selected, so split out the part which initializes smp_num_siblings.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44ca36de56d1bf196dca2eb67cd753a46961ffe6 upstream.
Real 32bit AMD CPUs do not have SMT and the only value of the call was to
reach the magic printout which got removed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55e6d279abd92cfd7576bba031e7589be8475edb upstream.
The value of this printout is dubious at best and there is no point in
having it in two different places along with convoluted ways to reach it.
Remove it completely.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05736e4ac13c08a4a9b1ef2de26dd31a32cbee57 upstream.
Provide a command line and a sysfs knob to control SMT.
The command line options are:
'nosmt': Enumerate secondary threads, but do not online them
'nosmt=force': Ignore secondary threads completely during enumeration
via MP table and ACPI/MADT.
The sysfs control file has the following states (read/write):
'on': SMT is enabled. Secondary threads can be freely onlined
'off': SMT is disabled. Secondary threads, even if enumerated
cannot be onlined
'forceoff': SMT is permanentely disabled. Writes to the control
file are rejected.
'notsupported': SMT is not supported by the CPU
The command line option 'nosmt' sets the sysfs control to 'off'. This
can be changed to 'on' to reenable SMT during runtime.
The command line option 'nosmt=force' sets the sysfs control to
'forceoff'. This cannot be changed during runtime.
When SMT is 'on' and the control file is changed to 'off' then all online
secondary threads are offlined and attempts to online a secondary thread
later on are rejected.
When SMT is 'off' and the control file is changed to 'on' then secondary
threads can be onlined again. The 'off' -> 'on' transition does not
automatically online the secondary threads.
When the control file is set to 'forceoff', the behaviour is the same as
setting it to 'off', but the operation is irreversible and later writes to
the control file are rejected.
When the control status is 'notsupported' then writes to the control file
are rejected.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc1fe215e1efa406b03aa4389e6269b61342dec5 upstream.
Split out the inner workings of do_cpu_down() to allow reuse of that
function for the upcoming SMT disabling mechanism.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4de65696d865c225fda3b9913b31284ea65ea96 upstream.
The asymmetry caused a warning to trigger if the bootup was stopped in state
CPUHP_AP_ONLINE_IDLE. The warning no longer triggers as kthread_park() can
now be invoked on already or still parked threads. But there is still no
reason to have this be asymmetric.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f048c399e0f7490ab7296bc2c255d37eb14a9675 upstream.
Provide information whether SMT is supoorted by the CPUs. Preparatory patch
for SMT control mechanism.
Suggested-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a4d2657e048f096c7ffcad254010bd94891c8c0 upstream.
If the CPU is supporting SMT then the primary thread can be found by
checking the lower APIC ID bits for zero. smp_num_siblings is used to build
the mask for the APIC ID bits which need to be taken into account.
This uses the MPTABLE or ACPI/MADT supplied APIC ID, which can be different
than the initial APIC ID in CPUID. But according to AMD the lower bits have
to be consistent. Intel gave a tentative confirmation as well.
Preparatory patch to support disabling SMT at boot/runtime.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba2591a5993eabcc8e874e30f361d8ffbb10d6d4 upstream.
The static key sched_smt_present is only updated at boot time when SMT
siblings have been detected. Booting with maxcpus=1 and bringing the
siblings online after boot rebuilds the scheduling domains correctly but
does not update the static key, so the SMT code is not enabled.
Let the key be updated in the scheduler CPU hotplug code to fix this.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56563f53d3066afa9e63d6c997bf67e76a8b05c0 upstream.
The pr_warn in l1tf_select_mitigation would have used the prior pr_fmt
which was defined as "Spectre V2 : ".
Move the function to be past SSBD and also define the pr_fmt.
Fixes: 17dbca119312 ("x86/speculation/l1tf: Add sysfs reporting for l1tf")
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 377eeaa8e11fe815b1d07c81c4a0e2843a8c15eb upstream.
For the L1TF workaround its necessary to limit the swap file size to below
MAX_PA/2, so that the higher bits of the swap offset inverted never point
to valid memory.
Add a mechanism for the architecture to override the swap file size check
in swapfile.c and add a x86 specific max swapfile check function that
enforces that limit.
The check is only enabled if the CPU is vulnerable to L1TF.
In VMs with 42bit MAX_PA the typical limit is 2TB now, on a native system
with 46bit PA it is 32TB. The limit is only per individual swap file, so
it's always possible to exceed these limits with multiple swap files or
partitions.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42e4089c7890725fcd329999252dc489b72f2921 upstream.
For L1TF PROT_NONE mappings are protected by inverting the PFN in the page
table entry. This sets the high bits in the CPU's address space, thus
making sure to point to not point an unmapped entry to valid cached memory.
Some server system BIOSes put the MMIO mappings high up in the physical
address space. If such an high mapping was mapped to unprivileged users
they could attack low memory by setting such a mapping to PROT_NONE. This
could happen through a special device driver which is not access
protected. Normal /dev/mem is of course access protected.
To avoid this forbid PROT_NONE mappings or mprotect for high MMIO mappings.
Valid page mappings are allowed because the system is then unsafe anyways.
It's not expected that users commonly use PROT_NONE on MMIO. But to
minimize any impact this is only enforced if the mapping actually refers to
a high MMIO address (defined as the MAX_PA-1 bit being set), and also skip
the check for root.
For mmaps this is straight forward and can be handled in vm_insert_pfn and
in remap_pfn_range().
For mprotect it's a bit trickier. At the point where the actual PTEs are
accessed a lot of state has been changed and it would be difficult to undo
on an error. Since this is a uncommon case use a separate early page talk
walk pass for MMIO PROT_NONE mappings that checks for this condition
early. For non MMIO and non PROT_NONE there are no changes.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17dbca119312b4e8173d4e25ff64262119fcef38 upstream.
L1TF core kernel workarounds are cheap and normally always enabled, However
they still should be reported in sysfs if the system is vulnerable or
mitigated. Add the necessary CPU feature/bug bits.
- Extend the existing checks for Meltdowns to determine if the system is
vulnerable. All CPUs which are not vulnerable to Meltdown are also not
vulnerable to L1TF
- Check for 32bit non PAE and emit a warning as there is no practical way
for mitigation due to the limited physical address bits
- If the system has more than MAX_PA/2 physical memory the invert page
workarounds don't protect the system against the L1TF attack anymore,
because an inverted physical address will also point to valid
memory. Print a warning in this case and report that the system is
vulnerable.
Add a function which returns the PFN limit for the L1TF mitigation, which
will be used in follow up patches for sanity and range checks.
[ tglx: Renamed the CPU feature bit to L1TF_PTEINV ]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10a70416e1f067f6c4efda6ffd8ea96002ac4223 upstream.
The L1TF workaround doesn't make any attempt to mitigate speculate accesses
to the first physical page for zeroed PTEs. Normally it only contains some
data from the early real mode BIOS.
It's not entirely clear that the first page is reserved in all
configurations, so add an extra reservation call to make sure it is really
reserved. In most configurations (e.g. with the standard reservations)
it's likely a nop.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b28baca9b1f0d4a42b865da7a05b1c81424bd5c upstream.
When PTEs are set to PROT_NONE the kernel just clears the Present bit and
preserves the PFN, which creates attack surface for L1TF speculation
speculation attacks.
This is important inside guests, because L1TF speculation bypasses physical
page remapping. While the host has its own migitations preventing leaking
data from other VMs into the guest, this would still risk leaking the wrong
page inside the current guest.
This uses the same technique as Linus' swap entry patch: while an entry is
is in PROTNONE state invert the complete PFN part part of it. This ensures
that the the highest bit will point to non existing memory.
The invert is done by pte/pmd_modify and pfn/pmd/pud_pte for PROTNONE and
pte/pmd/pud_pfn undo it.
This assume that no code path touches the PFN part of a PTE directly
without using these primitives.
This doesn't handle the case that MMIO is on the top of the CPU physical
memory. If such an MMIO region was exposed by an unpriviledged driver for
mmap it would be possible to attack some real memory. However this
situation is all rather unlikely.
For 32bit non PAE the inversion is not done because there are really not
enough bits to protect anything.
Q: Why does the guest need to be protected when the HyperVisor already has
L1TF mitigations?
A: Here's an example:
Physical pages 1 2 get mapped into a guest as
GPA 1 -> PA 2
GPA 2 -> PA 1
through EPT.
The L1TF speculation ignores the EPT remapping.
Now the guest kernel maps GPA 1 to process A and GPA 2 to process B, and
they belong to different users and should be isolated.
A sets the GPA 1 PA 2 PTE to PROT_NONE to bypass the EPT remapping and
gets read access to the underlying physical page. Which in this case
points to PA 2, so it can read process B's data, if it happened to be in
L1, so isolation inside the guest is broken.
There's nothing the hypervisor can do about this. This mitigation has to
be done in the guest itself.
[ tglx: Massaged changelog ]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f22b4cd45b67b3496f4aa4c7180a1271c6452f6 upstream.
With L1 terminal fault the CPU speculates into unmapped PTEs, and resulting
side effects allow to read the memory the PTE is pointing too, if its
values are still in the L1 cache.
For swapped out pages Linux uses unmapped PTEs and stores a swap entry into
them.
To protect against L1TF it must be ensured that the swap entry is not
pointing to valid memory, which requires setting higher bits (between bit
36 and bit 45) that are inside the CPUs physical address space, but outside
any real memory.
To do this invert the offset to make sure the higher bits are always set,
as long as the swap file is not too big.
Note there is no workaround for 32bit !PAE, or on systems which have more
than MAX_PA/2 worth of memory. The later case is very unlikely to happen on
real systems.
[AK: updated description and minor tweaks by. Split out from the original
patch ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcd11afa7adad8d720e7ba5ef58bdcd9775cf45f upstream.
If pages are swapped out, the swap entry is stored in the corresponding
PTE, which has the Present bit cleared. CPUs vulnerable to L1TF speculate
on PTE entries which have the present bit set and would treat the swap
entry as phsyical address (PFN). To mitigate that the upper bits of the PTE
must be set so the PTE points to non existent memory.
The swap entry stores the type and the offset of a swapped out page in the
PTE. type is stored in bit 9-13 and offset in bit 14-63. The hardware
ignores the bits beyond the phsyical address space limit, so to make the
mitigation effective its required to start 'offset' at the lowest possible
bit so that even large swap offsets do not reach into the physical address
space limit bits.
Move offset to bit 9-58 and type to bit 59-63 which are the bits that
hardware generally doesn't care about.
That, in turn, means that if you on desktop chip with only 40 bits of
physical addressing, now that the offset starts at bit 9, there needs to be
30 bits of offset actually *in use* until bit 39 ends up being set, which
means when inverted it will again point into existing memory.
So that's 4 terabyte of swap space (because the offset is counted in pages,
so 30 bits of offset is 42 bits of actual coverage). With bigger physical
addressing, that obviously grows further, until the limit of the offset is
hit (at 50 bits of offset - 62 bits of actual swap file coverage).
This is a preparatory change for the actual swap entry inversion to protect
against L1TF.
[ AK: Updated description and minor tweaks. Split into two parts ]
[ tglx: Massaged changelog ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50896e180c6aa3a9c61a26ced99e15d602666a4c upstream.
L1 Terminal Fault (L1TF) is a speculation related vulnerability. The CPU
speculates on PTE entries which do not have the PRESENT bit set, if the
content of the resulting physical address is available in the L1D cache.
The OS side mitigation makes sure that a !PRESENT PTE entry points to a
physical address outside the actually existing and cachable memory
space. This is achieved by inverting the upper bits of the PTE. Due to the
address space limitations this only works for 64bit and 32bit PAE kernels,
but not for 32bit non PAE.
This mitigation applies to both host and guest kernels, but in case of a
64bit host (hypervisor) and a 32bit PAE guest, inverting the upper bits of
the PAE address space (44bit) is not enough if the host has more than 43
bits of populated memory address space, because the speculation treats the
PTE content as a physical host address bypassing EPT.
The host (hypervisor) protects itself against the guest by flushing L1D as
needed, but pages inside the guest are not protected against attacks from
other processes inside the same guest.
For the guest the inverted PTE mask has to match the host to provide the
full protection for all pages the host could possibly map into the
guest. The hosts populated address space is not known to the guest, so the
mask must cover the possible maximal host address space, i.e. 52 bit.
On 32bit PAE the maximum PTE mask is currently set to 44 bit because that
is the limit imposed by 32bit unsigned long PFNs in the VMs. This limits
the mask to be below what the host could possible use for physical pages.
The L1TF PROT_NONE protection code uses the PTE masks to determine which
bits to invert to make sure the higher bits are set for unmapped entries to
prevent L1TF speculation attacks against EPT inside guests.
In order to invert all bits that could be used by the host, increase
__PHYSICAL_PAGE_SHIFT to 52 to match 64bit.
The real limit for a 32bit PAE kernel is still 44 bits because all Linux
PTEs are created from unsigned long PFNs, so they cannot be higher than 44
bits on a 32bit kernel. So these extra PFN bits should be never set. The
only users of this macro are using it to look at PTEs, so it's safe.
[ tglx: Massaged changelog ]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fdf82a7856b32d905c39afc85e34364491e46346 upstream.
The article "Spectre Returns! Speculation Attacks using the Return Stack
Buffer" [1] describes two new (sub-)variants of spectrev2-like attacks,
making use solely of the RSB contents even on CPUs that don't fallback to
BTB on RSB underflow (Skylake+).
Mitigate userspace-userspace attacks by always unconditionally filling RSB on
context switch when the generic spectrev2 mitigation has been enabled.
[1] https://arxiv.org/pdf/1807.07940.pdf
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/nycvar.YFH.7.76.1807261308190.997@cbobk.fhfr.pm
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5800dc5c19f34e6e03b5adab1282535cb102fafd upstream.
Nadav reported that on guests we're failing to rewrite the indirect
calls to CALLEE_SAVE paravirt functions. In particular the
pv_queued_spin_unlock() call is left unpatched and that is all over the
place. This obviously wrecks Spectre-v2 mitigation (for paravirt
guests) which relies on not actually having indirect calls around.
The reason is an incorrect clobber test in paravirt_patch_call(); this
function rewrites an indirect call with a direct call to the _SAME_
function, there is no possible way the clobbers can be different
because of this.
Therefore remove this clobber check. Also put WARNs on the other patch
failure case (not enough room for the instruction) which I've not seen
trigger in my (limited) testing.
Three live kernel image disassemblies for lock_sock_nested (as a small
function that illustrates the problem nicely). PRE is the current
situation for guests, POST is with this patch applied and NATIVE is with
or without the patch for !guests.
PRE:
(gdb) disassemble lock_sock_nested
Dump of assembler code for function lock_sock_nested:
0xffffffff817be970 <+0>: push %rbp
0xffffffff817be971 <+1>: mov %rdi,%rbp
0xffffffff817be974 <+4>: push %rbx
0xffffffff817be975 <+5>: lea 0x88(%rbp),%rbx
0xffffffff817be97c <+12>: callq 0xffffffff819f7160 <_cond_resched>
0xffffffff817be981 <+17>: mov %rbx,%rdi
0xffffffff817be984 <+20>: callq 0xffffffff819fbb00 <_raw_spin_lock_bh>
0xffffffff817be989 <+25>: mov 0x8c(%rbp),%eax
0xffffffff817be98f <+31>: test %eax,%eax
0xffffffff817be991 <+33>: jne 0xffffffff817be9ba <lock_sock_nested+74>
0xffffffff817be993 <+35>: movl $0x1,0x8c(%rbp)
0xffffffff817be99d <+45>: mov %rbx,%rdi
0xffffffff817be9a0 <+48>: callq *0xffffffff822299e8
0xffffffff817be9a7 <+55>: pop %rbx
0xffffffff817be9a8 <+56>: pop %rbp
0xffffffff817be9a9 <+57>: mov $0x200,%esi
0xffffffff817be9ae <+62>: mov $0xffffffff817be993,%rdi
0xffffffff817be9b5 <+69>: jmpq 0xffffffff81063ae0 <__local_bh_enable_ip>
0xffffffff817be9ba <+74>: mov %rbp,%rdi
0xffffffff817be9bd <+77>: callq 0xffffffff817be8c0 <__lock_sock>
0xffffffff817be9c2 <+82>: jmp 0xffffffff817be993 <lock_sock_nested+35>
End of assembler dump.
POST:
(gdb) disassemble lock_sock_nested
Dump of assembler code for function lock_sock_nested:
0xffffffff817be970 <+0>: push %rbp
0xffffffff817be971 <+1>: mov %rdi,%rbp
0xffffffff817be974 <+4>: push %rbx
0xffffffff817be975 <+5>: lea 0x88(%rbp),%rbx
0xffffffff817be97c <+12>: callq 0xffffffff819f7160 <_cond_resched>
0xffffffff817be981 <+17>: mov %rbx,%rdi
0xffffffff817be984 <+20>: callq 0xffffffff819fbb00 <_raw_spin_lock_bh>
0xffffffff817be989 <+25>: mov 0x8c(%rbp),%eax
0xffffffff817be98f <+31>: test %eax,%eax
0xffffffff817be991 <+33>: jne 0xffffffff817be9ba <lock_sock_nested+74>
0xffffffff817be993 <+35>: movl $0x1,0x8c(%rbp)
0xffffffff817be99d <+45>: mov %rbx,%rdi
0xffffffff817be9a0 <+48>: callq 0xffffffff810a0c20 <__raw_callee_save___pv_queued_spin_unlock>
0xffffffff817be9a5 <+53>: xchg %ax,%ax
0xffffffff817be9a7 <+55>: pop %rbx
0xffffffff817be9a8 <+56>: pop %rbp
0xffffffff817be9a9 <+57>: mov $0x200,%esi
0xffffffff817be9ae <+62>: mov $0xffffffff817be993,%rdi
0xffffffff817be9b5 <+69>: jmpq 0xffffffff81063aa0 <__local_bh_enable_ip>
0xffffffff817be9ba <+74>: mov %rbp,%rdi
0xffffffff817be9bd <+77>: callq 0xffffffff817be8c0 <__lock_sock>
0xffffffff817be9c2 <+82>: jmp 0xffffffff817be993 <lock_sock_nested+35>
End of assembler dump.
NATIVE:
(gdb) disassemble lock_sock_nested
Dump of assembler code for function lock_sock_nested:
0xffffffff817be970 <+0>: push %rbp
0xffffffff817be971 <+1>: mov %rdi,%rbp
0xffffffff817be974 <+4>: push %rbx
0xffffffff817be975 <+5>: lea 0x88(%rbp),%rbx
0xffffffff817be97c <+12>: callq 0xffffffff819f7160 <_cond_resched>
0xffffffff817be981 <+17>: mov %rbx,%rdi
0xffffffff817be984 <+20>: callq 0xffffffff819fbb00 <_raw_spin_lock_bh>
0xffffffff817be989 <+25>: mov 0x8c(%rbp),%eax
0xffffffff817be98f <+31>: test %eax,%eax
0xffffffff817be991 <+33>: jne 0xffffffff817be9ba <lock_sock_nested+74>
0xffffffff817be993 <+35>: movl $0x1,0x8c(%rbp)
0xffffffff817be99d <+45>: mov %rbx,%rdi
0xffffffff817be9a0 <+48>: movb $0x0,(%rdi)
0xffffffff817be9a3 <+51>: nopl 0x0(%rax)
0xffffffff817be9a7 <+55>: pop %rbx
0xffffffff817be9a8 <+56>: pop %rbp
0xffffffff817be9a9 <+57>: mov $0x200,%esi
0xffffffff817be9ae <+62>: mov $0xffffffff817be993,%rdi
0xffffffff817be9b5 <+69>: jmpq 0xffffffff81063ae0 <__local_bh_enable_ip>
0xffffffff817be9ba <+74>: mov %rbp,%rdi
0xffffffff817be9bd <+77>: callq 0xffffffff817be8c0 <__lock_sock>
0xffffffff817be9c2 <+82>: jmp 0xffffffff817be993 <lock_sock_nested+35>
End of assembler dump.
Fixes: 63f70270ccd9 ("[PATCH] i386: PARAVIRT: add common patching machinery")
Fixes: 3010a0663fd9 ("x86/paravirt, objtool: Annotate indirect calls")
Reported-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eight fixes. The most important one is the mpt3sas fix which makes
the driver work again on big endian systems. The rest are mostly
minor error path or checker issues and the vmw_scsi one fixes a
performance problem.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW28FqCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishRC9AP9sRmgl
MunaMCjubXaN2jkmyoga43ZckSVXz0wQUALI9gD+PE0At8vCbWx0tFTQLN5/QEtC
HsVMiAdHSZ87wF7ZQtw=
=ehub
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Eight fixes.
The most important one is the mpt3sas fix which makes the driver work
again on big endian systems. The rest are mostly minor error path or
checker issues and the vmw_scsi one fixes a performance problem"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: vmw_pvscsi: Return DID_RESET for status SAM_STAT_COMMAND_TERMINATED
scsi: sr: Avoid that opening a CD-ROM hangs with runtime power management enabled
scsi: mpt3sas: Swap I/O memory read value back to cpu endianness
scsi: fcoe: clear FC_RP_STARTED flags when receiving a LOGO
scsi: fcoe: drop frames in ELS LOGO error path
scsi: fcoe: fix use-after-free in fcoe_ctlr_els_send
scsi: qedi: Fix a potential buffer overflow
scsi: qla2xxx: Fix memory leak for allocating abort IOCB
This is purely a preparatory patch for upcoming changes during the 4.19
merge window.
We have a function called "boot_cpu_state_init()" that isn't really
about the bootup cpu state: that is done much earlier by the similarly
named "boot_cpu_init()" (note lack of "state" in name).
This function initializes some hotplug CPU state, and needs to run after
the percpu data has been properly initialized. It even has a comment to
that effect.
Except it _doesn't_ actually run after the percpu data has been properly
initialized. On x86 it happens to do that, but on at least arm and
arm64, the percpu base pointers are initialized by the arch-specific
'smp_prepare_boot_cpu()' hook, which ran _after_ boot_cpu_state_init().
This had some unexpected results, and in particular we have a patch
pending for the merge window that did the obvious cleanup of using
'this_cpu_write()' in the cpu hotplug init code:
- per_cpu_ptr(&cpuhp_state, smp_processor_id())->state = CPUHP_ONLINE;
+ this_cpu_write(cpuhp_state.state, CPUHP_ONLINE);
which is obviously the right thing to do. Except because of the
ordering issue, it actually failed miserably and unexpectedly on arm64.
So this just fixes the ordering, and changes the name of the function to
be 'boot_cpu_hotplug_init()' to make it obvious that it's about cpu
hotplug state, because the core CPU state was supposed to have already
been done earlier.
Marked for stable, since the (not yet merged) patch that will show this
problem is marked for stable.
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Mian Yousaf Kaukab <yousaf.kaukab@suse.com>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs fixes from Al Viro:
"A bunch of race fixes, mostly around lazy pathwalk.
All of it is -stable fodder, a large part going back to 2013"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
make sure that __dentry_kill() always invalidates d_seq, unhashed or not
fix __legitimize_mnt()/mntput() race
fix mntput/mntput race
root dentries need RCU-delayed freeing
Pull networking fixes from David Miller:
"Last bit of straggler fixes...
1) Fix btf library licensing to LGPL, from Martin KaFai lau.
2) Fix error handling in bpf sockmap code, from Daniel Borkmann.
3) XDP cpumap teardown handling wrt. execution contexts, from Jesper
Dangaard Brouer.
4) Fix loss of runtime PM on failed vlan add/del, from Ivan
Khoronzhuk.
5) xen-netfront caches skb_shinfo(skb) across a __pskb_pull_tail()
call, which potentially changes the skb's data buffer, and thus
skb_shinfo(). Fix from Juergen Gross"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
xen/netfront: don't cache skb_shinfo()
net: ethernet: ti: cpsw: fix runtime_pm while add/kill vlan
net: ethernet: ti: cpsw: clear all entries when delete vid
xdp: fix bug in devmap teardown code path
samples/bpf: xdp_redirect_cpu adjustment to reproduce teardown race easier
xdp: fix bug in cpumap teardown code path
bpf, sockmap: fix cork timeout for select due to epipe
bpf, sockmap: fix leak in bpf_tcp_sendmsg wait for mem path
bpf, sockmap: fix bpf_tcp_sendmsg sock error handling
bpf: btf: Change tools/lib/bpf/btf to LGPL
skb_shinfo() can change when calling __pskb_pull_tail(): Don't cache
its return value.
Cc: stable@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko says:
====================
net: ethernet: ti: cpsw: fix runtime pm while add/del reserved vid
Here 2 not critical fixes for:
- vlan ale table leak while error if deleting vlan (simplifies next fix)
- runtime pm while try to set reserved vlan
====================
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's exclusive with normal behaviour but if try to set vlan to one of
the reserved values is made, the cpsw runtime pm is broken.
Fixes: a6c5d14f5136 ("drivers: net: cpsw: ndev: fix accessing to suspended device")
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In cases if some of the entries were not found in forwarding table
while killing vlan, the rest not needed entries still left in the
table. No need to stop, as entry was deleted anyway. So fix this by
returning error only after all was cleaned. To implement this, return
-ENOENT in cpsw_ale_del_mcast() as it's supposed to be.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If zram supports writeback feature, it's no longer a
BD_CAP_SYNCHRONOUS_IO device beause zram does asynchronous IO operations
for incompressible pages.
Do not pretend to be synchronous IO device. It makes the system very
sluggish due to waiting for IO completion from upper layers.
Furthermore, it causes a user-after-free problem because swap thinks the
opearion is done when the IO functions returns so it can free the page
(e.g., lock_page_or_retry and goto out_release in do_swap_page) but in
fact, IO is asynchronous so the driver could access a just freed page
afterward.
This patch fixes the problem.
BUG: Bad page state in process qemu-system-x86 pfn:3dfab21
page:ffffdfb137eac840 count:0 mapcount:0 mapping:0000000000000000 index:0x1
flags: 0x17fffc000000008(uptodate)
raw: 017fffc000000008 dead000000000100 dead000000000200 0000000000000000
raw: 0000000000000001 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set
bad because of flags: 0x8(uptodate)
CPU: 4 PID: 1039 Comm: qemu-system-x86 Tainted: G B 4.18.0-rc5+ #1
Hardware name: Supermicro Super Server/X10SRL-F, BIOS 2.0b 05/02/2017
Call Trace:
dump_stack+0x5c/0x7b
bad_page+0xba/0x120
get_page_from_freelist+0x1016/0x1250
__alloc_pages_nodemask+0xfa/0x250
alloc_pages_vma+0x7c/0x1c0
do_swap_page+0x347/0x920
__handle_mm_fault+0x7b4/0x1110
handle_mm_fault+0xfc/0x1f0
__get_user_pages+0x12f/0x690
get_user_pages_unlocked+0x148/0x1f0
__gfn_to_pfn_memslot+0xff/0x3c0 [kvm]
try_async_pf+0x87/0x230 [kvm]
tdp_page_fault+0x132/0x290 [kvm]
kvm_mmu_page_fault+0x74/0x570 [kvm]
kvm_arch_vcpu_ioctl_run+0x9b3/0x1990 [kvm]
kvm_vcpu_ioctl+0x388/0x5d0 [kvm]
do_vfs_ioctl+0xa2/0x630
ksys_ioctl+0x70/0x80
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x55/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Link: https://lore.kernel.org/lkml/0516ae2d-b0fd-92c5-aa92-112ba7bd32fc@contabo.de/
Link: http://lkml.kernel.org/r/20180802051112.86174-1-minchan@kernel.org
[minchan@kernel.org: fix changelog, add comment]
Link: https://lore.kernel.org/lkml/0516ae2d-b0fd-92c5-aa92-112ba7bd32fc@contabo.de/
Link: http://lkml.kernel.org/r/20180802051112.86174-1-minchan@kernel.org
Link: http://lkml.kernel.org/r/20180805233722.217347-1-minchan@kernel.org
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reported-by: Tino Lehnig <tino.lehnig@contabo.de>
Tested-by: Tino Lehnig <tino.lehnig@contabo.de>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org> [4.15+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ioremap_prot() can return NULL which could lead to an oops.
Link: http://lkml.kernel.org/r/1533195441-58594-1-git-send-email-chenjie6@huawei.com
Signed-off-by: chen jie <chenjie6@huawei.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: chenjie <chenjie6@huawei.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With gcc-8 fsanitize=null become very noisy. GCC started to complain
about things like &a->b, where 'a' is NULL pointer. There is no NULL
dereference, we just calculate address to struct member. It's
technically undefined behavior so UBSAN is correct to report it. But as
long as there is no real NULL-dereference, I think, we should be fine.
-fno-delete-null-pointer-checks compiler flag should protect us from any
consequences. So let's just no use -fsanitize=null as it's not useful
for us. If there is a real NULL-deref we will see crash. Even if
userspace mapped something at NULL (root can do this), with things like
SMAP should catch the issue.
Link: http://lkml.kernel.org/r/20180802153209.813-1-aryabinin@virtuozzo.com
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This entry was created with my personal e-mail address. Update this entry
to my open-source kernel.org account.
Link: http://lkml.kernel.org/r/20180806143904.4716-4-kieran.bingham@ideasonboard.com
Signed-off-by: Kieran Bingham <kbingham@kernel.org>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull i2c fix from Wolfram Sang:
"A single driver bugfix for I2C.
The bug was found by systematically stress testing the driver, so I am
confident to merge it that late in the cycle although it is probably
unusually large"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: xlp9xx: Fix case where SSIF read transaction completes early
Daniel Borkmann says:
====================
pull-request: bpf 2018-08-10
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix cpumap and devmap on teardown as they're under RCU context
and won't have same assumption as running under NAPI protection,
from Jesper.
2) Fix various sockmap bugs in bpf_tcp_sendmsg() code, e.g. we had
a bug where socket error was not propagated correctly, from Daniel.
3) Fix incompatible libbpf header license for BTF code and match it
before it gets officially released with the rest of libbpf which
is LGPL-2.1, from Martin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
RCU pathwalk relies upon the assumption that anything that changes
->d_inode of a dentry will invalidate its ->d_seq. That's almost
true - the one exception is that the final dput() of already unhashed
dentry does *not* touch ->d_seq at all. Unhashing does, though,
so for anything we'd found by RCU dcache lookup we are fine.
Unfortunately, we can *start* with an unhashed dentry or jump into
it.
We could try and be careful in the (few) places where that could
happen. Or we could just make the final dput() invalidate the damn
thing, unhashed or not. The latter is much simpler and easier to
backport, so let's do it that way.
Reported-by: "Dae R. Jeong" <threeearcat@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
__legitimize_mnt() has two problems - one is that in case of success
the check of mount_lock is not ordered wrt preceding increment of
refcount, making it possible to have successful __legitimize_mnt()
on one CPU just before the otherwise final mntpu() on another,
with __legitimize_mnt() not seeing mntput() taking the lock and
mntput() not seeing the increment done by __legitimize_mnt().
Solved by a pair of barriers.
Another is that failure of __legitimize_mnt() on the second
read_seqretry() leaves us with reference that'll need to be
dropped by caller; however, if that races with final mntput()
we can end up with caller dropping rcu_read_lock() and doing
mntput() to release that reference - with the first mntput()
having freed the damn thing just as rcu_read_lock() had been
dropped. Solution: in "do mntput() yourself" failure case
grab mount_lock, check if MNT_DOOMED has been set by racing
final mntput() that has missed our increment and if it has -
undo the increment and treat that as "failure, caller doesn't
need to drop anything" case.
It's not easy to hit - the final mntput() has to come right
after the first read_seqretry() in __legitimize_mnt() *and*
manage to miss the increment done by __legitimize_mnt() before
the second read_seqretry() in there. The things that are almost
impossible to hit on bare hardware are not impossible on SMP
KVM, though...
Reported-by: Oleg Nesterov <oleg@redhat.com>
Fixes: 48a066e72d97 ("RCU'd vsfmounts")
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
mntput_no_expire() does the calculation of total refcount under mount_lock;
unfortunately, the decrement (as well as all increments) are done outside
of it, leading to false positives in the "are we dropping the last reference"
test. Consider the following situation:
* mnt is a lazy-umounted mount, kept alive by two opened files. One
of those files gets closed. Total refcount of mnt is 2. On CPU 42
mntput(mnt) (called from __fput()) drops one reference, decrementing component
* After it has looked at component #0, the process on CPU 0 does
mntget(), incrementing component #0, gets preempted and gets to run again -
on CPU 69. There it does mntput(), which drops the reference (component #69)
and proceeds to spin on mount_lock.
* On CPU 42 our first mntput() finishes counting. It observes the
decrement of component #69, but not the increment of component #0. As the
result, the total it gets is not 1 as it should've been - it's 0. At which
point we decide that vfsmount needs to be killed and proceed to free it and
shut the filesystem down. However, there's still another opened file
on that filesystem, with reference to (now freed) vfsmount, etc. and we are
screwed.
It's not a wide race, but it can be reproduced with artificial slowdown of
the mnt_get_count() loop, and it should be easier to hit on SMP KVM setups.
Fix consists of moving the refcount decrement under mount_lock; the tricky
part is that we want (and can) keep the fast case (i.e. mount that still
has non-NULL ->mnt_ns) entirely out of mount_lock. All places that zero
mnt->mnt_ns are dropping some reference to mnt and they call synchronize_rcu()
before that mntput(). IOW, if mntput() observes (under rcu_read_lock())
a non-NULL ->mnt_ns, it is guaranteed that there is another reference yet to
be dropped.
Reported-by: Jann Horn <jannh@google.com>
Tested-by: Jann Horn <jannh@google.com>
Fixes: 48a066e72d97 ("RCU'd vsfmounts")
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
