IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-12-08 (ice)
Jacob Keller says:
This series of patches primarily consists of changes to fix some corner
cases that can cause Tx timestamp failures. The issues were discovered and
reported by Siddaraju DH and primarily affect E822 hardware, though this
series also includes some improvements that affect E810 hardware as well.
The primary issue is regarding the way that E822 determines when to generate
timestamp interrupts. If the driver reads timestamp indexes which do not
have a valid timestamp, the E822 interrupt tracking logic can get stuck.
This is due to the way that E822 hardware tracks timestamp index reads
internally. I was previously unaware of this behavior as it is significantly
different in E810 hardware.
Most of the fixes target refactors to ensure that the ice driver does not
read timestamp indexes which are not valid on E822 hardware. This is done by
using the Tx timestamp ready bitmap register from the PHY. This register
indicates what timestamp indexes have outstanding timestamps waiting to be
captured.
Care must be taken in all cases where we read the timestamp registers, and
thus all flows which might have read these registers are refactored. The
ice_ptp_tx_tstamp function is modified to consolidate as much of the logic
relating to these registers as possible. It now handles discarding stale
timestamps which are old or which occurred after a PHC time update. This
replaces previously standalone thread functions like the periodic work
function and the ice_ptp_flush_tx_tracker function.
In addition, some minor cleanups noticed while writing these refactors are
included.
The remaining patches refactor the E822 implementation to remove the
"bypass" mode for timestamps. The E822 hardware has the ability to provide a
more precise timestamp by making use of measurements of the precise way that
packets flow through the hardware pipeline. These measurements are known as
"Vernier" calibration. The "bypass" mode disables many of these measurements
in favor of a faster start up time for Tx and Rx timestamping. Instead, once
these measurements were captured, the driver tries to reconfigure the PHY to
enable the vernier calibrations.
Unfortunately this recalibration does not work. Testing indicates that the
PHY simply remains in bypass mode without the increased timestamp precision.
Remove the attempt at recalibration and always use vernier mode. This has
one disadvantage that Tx and Rx timestamps cannot begin until after at least
one packet of that type goes through the hardware pipeline. Because of this,
further refactor the driver to separate Tx and Rx vernier calibration.
Complete the Tx and Rx independently, enabling the appropriate type of
timestamp as soon as the relevant packet has traversed the hardware
pipeline. This was reported by Milena Olech.
Note that although these might be considered "bug fixes", the required
changes in order to appropriately resolve these issues is large. Thus it
does not feel suitable to send this series to net.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: reschedule ice_ptp_wait_for_offset_valid during reset
ice: make Tx and Rx vernier offset calibration independent
ice: only check set bits in ice_ptp_flush_tx_tracker
ice: handle flushing stale Tx timestamps in ice_ptp_tx_tstamp
ice: cleanup allocations in ice_ptp_alloc_tx_tracker
ice: protect init and calibrating check in ice_ptp_request_ts
ice: synchronize the misc IRQ when tearing down Tx tracker
ice: check Tx timestamp memory register for ready timestamps
ice: handle discarding old Tx requests in ice_ptp_tx_tstamp
ice: always call ice_ptp_link_change and make it void
ice: fix misuse of "link err" with "link status"
ice: Reset TS memory for all quads
ice: Remove the E822 vernier "bypass" logic
ice: Use more generic names for ice_ptp_tx fields
====================
Link: https://lore.kernel.org/r/20221208213932.1274143-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support to count upall packets, when kmod of openvswitch
upcall to count the number of packets for upcall succeed and
failed, which is a better way to see how many packets upcalled
on every interfaces.
Signed-off-by: wangchuanlei <wangchuanlei@inspur.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rhashtable currently only does bh-safe synchronization making it impossible
to use from irq-safe contexts. Switch it to use irq-safe synchronization to
remove the restriction.
v2: Update the lock functions to return the ulong flags value and unlock
functions to take the value directly instead of passing around the
pointer. Suggested by Linus.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: David Vernet <dvernet@meta.com>
Acked-by: Josh Don <joshdon@google.com>
Acked-by: Hao Luo <haoluo@google.com>
Acked-by: Barret Rhoden <brho@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pedro Tammela says:
====================
net/sched: retpoline wrappers for tc
In tc all qdics, classifiers and actions can be compiled as modules.
This results today in indirect calls in all transitions in the tc hierarchy.
Due to CONFIG_RETPOLINE, CPUs with mitigations=on might pay an extra cost on
indirect calls. For newer Intel cpus with IBRS the extra cost is
nonexistent, but AMD Zen cpus and older x86 cpus still go through the
retpoline thunk.
Known built-in symbols can be optimized into direct calls, thus
avoiding the retpoline thunk. So far, tc has not been leveraging this
build information and leaving out a performance optimization for some
CPUs. In this series we wire up 'tcf_classify()' and 'tcf_action_exec()'
with direct calls when known modules are compiled as built-in as an
opt-in optimization.
We measured these changes in one AMD Zen 4 cpu (Retpoline), one AMD Zen 3 cpu (Retpoline),
one Intel 10th Gen CPU (IBRS), one Intel 3rd Gen cpu (Retpoline) and one
Intel Xeon CPU (IBRS) using pktgen with 64b udp packets. Our test setup is a
dummy device with clsact and matchall in a kernel compiled with every
tc module as built-in. We observed a 3-8% speed up on the retpoline CPUs,
when going through 1 tc filter, and a 60-100% speed up when going through 100 filters.
For the IBRS cpus we observed a 1-2% degradation in both scenarios, we believe
the extra branches check introduced a small overhead therefore we added
a static key that bypasses the wrapper on kernels not using the retpoline mitigation,
but compiled with CONFIG_RETPOLINE.
1 filter:
CPU | before (pps) | after (pps) | diff
R9 7950X | 5914980 | 6380227 | +7.8%
R9 5950X | 4237838 | 4412241 | +4.1%
R9 5950X | 4265287 | 4413757 | +3.4% [*]
i5-3337U | 1580565 | 1682406 | +6.4%
i5-10210U | 3006074 | 3006857 | +0.0%
i5-10210U | 3160245 | 3179945 | +0.6% [*]
Xeon 6230R | 3196906 | 3197059 | +0.0%
Xeon 6230R | 3190392 | 3196153 | +0.01% [*]
100 filters:
CPU | before (pps) | after (pps) | diff
R9 7950X | 373598 | 820396 | +119.59%
R9 5950X | 313469 | 633303 | +102.03%
R9 5950X | 313797 | 633150 | +101.77% [*]
i5-3337U | 127454 | 211210 | +65.71%
i5-10210U | 389259 | 381765 | -1.9%
i5-10210U | 408812 | 412730 | +0.9% [*]
Xeon 6230R | 415420 | 406612 | -2.1%
Xeon 6230R | 416705 | 405869 | -2.6% [*]
[*] In these tests we ran pktgen with clone set to 1000.
On the 7950x system we also tested the impact of filters if iteration order
placement varied, first by compiling a kernel with the filter under test being
the first one in the static iteration and then repeating it with being last (of 15 classifiers existing today).
We saw a difference of +0.5-1% in pps between being the first in the iteration vs being the last.
Therefore we order the classifiers and actions according to relevance per our current thinking.
v5->v6:
- Address Eric Dumazet suggestions
v4->v5:
- Rebase
v3->v4:
- Address Eric Dumazet suggestions
v2->v3:
- Address suggestions by Jakub, Paolo and Eric
- Dropped RFC tag (I forgot to add it on v2)
v1->v2:
- Fix build errors found by the bots
- Address Kuniyuki Iwashima suggestions
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose the necessary tc classifier functions and wire up cls_api to use
direct calls in retpoline kernels.
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose the necessary tc act functions and wire up act_api to use
direct calls in retpoline kernels.
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On kernels using retpoline as a spectrev2 mitigation,
optimize actions and filters that are compiled as built-ins into a direct call.
On subsequent patches we expose the classifiers and actions functions
and wire up the wrapper into tc.
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The type definition should be visible even in configurations not using
CONFIG_NET_CLS_ACT.
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete a few lines of "depends on PHYLIB" since they are inside
an "if PHYLIB / endif # PHYLIB" block, i.e., they are redundant
and the other 50+ drivers there don't use "depends on PHYLIB"
since it is not needed.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Link: https://lore.kernel.org/r/20221207044257.30036-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add an option to initialize SOF_TIMESTAMPING_OPT_ID for TCP from
write_seq sockets instead of snd_una.
This should have been the behavior from the start. Because processes
may now exist that rely on the established behavior, do not change
behavior of the existing option, but add the right behavior with a new
flag. It is encouraged to always set SOF_TIMESTAMPING_OPT_ID_TCP on
stream sockets along with the existing SOF_TIMESTAMPING_OPT_ID.
Intuitively the contract is that the counter is zero after the
setsockopt, so that the next write N results in a notification for
the last byte N - 1.
On idle sockets snd_una == write_seq and this holds for both. But on
sockets with data in transmission, snd_una records the unacked offset
in the stream. This depends on the ACK response from the peer. A
process cannot learn this in a race free manner (ioctl SIOCOUTQ is one
racy approach).
write_seq records the offset at the last byte written by the process.
This is a better starting point. It matches the intuitive contract in
all circumstances, unaffected by external behavior.
The new timestamp flag necessitates increasing sk_tsflags to 32 bits.
Move the field in struct sock to avoid growing the socket (for some
common CONFIG variants). The UAPI interface so_timestamping.flags is
already int, so 32 bits wide.
Reported-by: Sotirios Delimanolis <sotodel@meta.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20221207143701.29861-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lorenzo Bianconi says:
====================
fix possible deadlock during WED attach
Fix a possible deadlock in mtk_wed_attach if mtk_wed_wo_init routine fails.
Check wo pointer is properly allocated before running mtk_wed_wo_reset() and
mtk_wed_wo_deinit().
====================
Link: https://lore.kernel.org/r/cover.1670421354.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce __mtk_wed_detach() in order to avoid a deadlock in
mtk_wed_attach routine if mtk_wed_wo_init fails since both
mtk_wed_attach and mtk_wed_detach run holding hw_lock mutex.
Fixes: 4c5de09eb0d0 ("net: ethernet: mtk_wed: add configure wed wo support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix possible NULL pointer dereference in mtk_wed_detach routine checking
wo pointer is properly allocated before running mtk_wed_wo_reset() and
mtk_wed_wo_deinit().
Even if it is just a theoretical issue at the moment check wo pointer is
not NULL in mtk_wed_mcu_msg_update.
Moreover, honor mtk_wed_mcu_send_msg return value in mtk_wed_wo_reset()
Fixes: 799684448e3e ("net: ethernet: mtk_wed: introduce wed wo support")
Fixes: 4c5de09eb0d0 ("net: ethernet: mtk_wed: add configure wed wo support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a spelling mistake in a nn_dp_warn message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20221207094312.2281493-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The BPF Makefile in net/bpf did incorrect path substitution for O=dir
builds, e.g.
make O=/tmp/kselftest headers
make O=/tmp/kselftest -C tools/testing/selftests
would fail in selftest builds [1] net/ with
clang-16: error: no such file or directory: 'kselftest/net/bpf/nat6to4.c'
clang-16: error: no input files
Add a pattern prerequisite and an order-only-prerequisite (for
creating the directory), to resolve the issue.
[1] https://lore.kernel.org/all/202212060009.34CkQmCN-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 837a3d66d698 ("selftests: net: Add cross-compilation support for BPF programs")
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20221206102838.272584-1-bjorn@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Petr Machata says:
====================
mlxsw: Add Spectrum-1 ip6gre support
Ido Schimmel writes:
Currently, mlxsw only supports ip6gre offload on Spectrum-2 and newer
ASICs. Spectrum-1 can also offload ip6gre tunnels, but it needs double
entry router interfaces (RIFs) for the RIFs representing these tunnels.
In addition, the RIF index needs to be even. This is handled in
patches #1-#3.
The implementation can otherwise be shared between all Spectrum
generations. This is handled in patches #4-#5.
Patch #6 moves a mlxsw ip6gre selftest to a shared directory, as ip6gre
is no longer only supported on Spectrum-2 and newer ASICs.
This work is motivated by users that require multiple GRE tunnels that
all share the same underlay VRF. Currently, mlxsw only supports
decapsulation based on the underlay destination IP (i.e., not taking the
GRE key into account), so users need to configure these tunnels with
different source IPs and IPv6 addresses are easier to spare than IPv4.
Tested using existing ip6gre forwarding selftests.
====================
Link: https://lore.kernel.org/r/cover.1670414573.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that Spectrum-1 gained ip6gre support we can move the test out of
the Spectrum-2 directory.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in the previous patch, the existing Spectrum-2 ip6gre
implementation can be reused for Spectrum-1. Change the Spectrum-1
ip6gre operations structure to use the common operations.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are two main differences between Spectrum-1 and newer ASICs in
terms of IP-in-IP support:
1. In Spectrum-1, RIFs representing ip6gre tunnels require two entries
in the RIF table.
2. In Spectrum-2 and newer ASICs, packets ingress the underlay (during
encapsulation) and egress the underlay (during decapsulation) via a
special generic loopback RIF.
The first difference was handled in previous patches by adding the
'double_rif_entry' field to the Spectrum-1 operations structure of
ip6gre RIFs. The second difference is handled during RIF creation, by
only creating a generic loopback RIF in Spectrum-2 and newer ASICs.
Therefore, the ip6gre operations can be shared between Spectrum-1 and
newer ASIC in a similar fashion to how the ipgre operations are shared.
Rename the operations to not be Spectrum-2 specific and move them
earlier in the file so that they could later be used for Spectrum-1.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In Spectrum-1, loopback router interfaces (RIFs) used for IP-in-IP
encapsulation with an IPv6 underlay require two RIF entries and the RIF
index must be even.
Prepare for this change by extending the RIF parameters structure with a
'double_entry' field that indicates if the RIF being created requires
two RIF entries or not. Only set it for RIFs representing ip6gre tunnels
in Spectrum-1.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, each router interface (RIF) consumes one entry in the RIFs
table. This is going to change in subsequent patches where some RIFs
will consume two table entries.
Prepare for this change by parametrizing the RIF allocation size. For
now, always pass '1'.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, each router interface (RIF) consumes one entry in the RIFs
table and there are no alignment constraints. This is going to change in
subsequent patches where some RIFs will consume two table entries and
their indexes will need to be aligned to the allocation size (even).
Prepare for this change by converting the RIF index allocation to use
gen_pool with the 'gen_pool_first_fit_order_align' algorithm.
No Kconfig changes necessary as mlxsw already selects
'GENERIC_ALLOCATOR'.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current release - new code bugs:
- bonding: ipv6: correct address used in Neighbour Advertisement
parsing (src vs dst typo)
- fec: properly scope IRQ coalesce setup during link up to supported
chips only
Previous releases - regressions:
- Bluetooth fixes for fake CSR clones (knockoffs):
- re-add ERR_DATA_REPORTING quirk
- fix crash when device is replugged
- Bluetooth:
- silence a user-triggerable dmesg error message
- L2CAP: fix u8 overflow, oob access
- correct vendor codec definition
- fix support for Read Local Supported Codecs V2
- ti: am65-cpsw: fix RGMII configuration at SPEED_10
- mana: fix race on per-CQ variable NAPI work_done
Previous releases - always broken:
- af_unix: diag: fetch user_ns from in_skb in unix_diag_get_exact(),
avoid null-deref
- af_can: fix NULL pointer dereference in can_rcv_filter
- can: slcan: fix UAF with a freed work
- can: can327: flush TX_work on ldisc .close()
- macsec: add missing attribute validation for offload
- ipv6: avoid use-after-free in ip6_fragment()
- nft_set_pipapo: actually validate intervals in fields
after the first one
- mvneta: prevent oob access in mvneta_config_rss()
- ipv4: fix incorrect route flushing when table ID 0 is used,
or when source address is deleted
- phy: mxl-gpy: add workaround for IRQ bug on GPY215B and GPY215C
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=+mCl
-----END PGP SIGNATURE-----
Merge tag 'net-6.1-rc9' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth, can and netfilter.
Current release - new code bugs:
- bonding: ipv6: correct address used in Neighbour Advertisement
parsing (src vs dst typo)
- fec: properly scope IRQ coalesce setup during link up to supported
chips only
Previous releases - regressions:
- Bluetooth fixes for fake CSR clones (knockoffs):
- re-add ERR_DATA_REPORTING quirk
- fix crash when device is replugged
- Bluetooth:
- silence a user-triggerable dmesg error message
- L2CAP: fix u8 overflow, oob access
- correct vendor codec definition
- fix support for Read Local Supported Codecs V2
- ti: am65-cpsw: fix RGMII configuration at SPEED_10
- mana: fix race on per-CQ variable NAPI work_done
Previous releases - always broken:
- af_unix: diag: fetch user_ns from in_skb in unix_diag_get_exact(),
avoid null-deref
- af_can: fix NULL pointer dereference in can_rcv_filter
- can: slcan: fix UAF with a freed work
- can: can327: flush TX_work on ldisc .close()
- macsec: add missing attribute validation for offload
- ipv6: avoid use-after-free in ip6_fragment()
- nft_set_pipapo: actually validate intervals in fields after the
first one
- mvneta: prevent oob access in mvneta_config_rss()
- ipv4: fix incorrect route flushing when table ID 0 is used, or when
source address is deleted
- phy: mxl-gpy: add workaround for IRQ bug on GPY215B and GPY215C"
* tag 'net-6.1-rc9' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (77 commits)
net: dsa: sja1105: avoid out of bounds access in sja1105_init_l2_policing()
s390/qeth: fix use-after-free in hsci
macsec: add missing attribute validation for offload
net: mvneta: Fix an out of bounds check
net: thunderbolt: fix memory leak in tbnet_open()
ipv6: avoid use-after-free in ip6_fragment()
net: plip: don't call kfree_skb/dev_kfree_skb() under spin_lock_irq()
net: phy: mxl-gpy: add MDINT workaround
net: dsa: mv88e6xxx: accept phy-mode = "internal" for internal PHY ports
xen/netback: don't call kfree_skb() under spin_lock_irqsave()
dpaa2-switch: Fix memory leak in dpaa2_switch_acl_entry_add() and dpaa2_switch_acl_entry_remove()
ethernet: aeroflex: fix potential skb leak in greth_init_rings()
tipc: call tipc_lxc_xmit without holding node_read_lock
can: esd_usb: Allow REC and TEC to return to zero
can: can327: flush TX_work on ldisc .close()
can: slcan: fix freed work crash
can: af_can: fix NULL pointer dereference in can_rcv_filter
net: dsa: sja1105: fix memory leak in sja1105_setup_devlink_regions()
ipv4: Fix incorrect route flushing when table ID 0 is used
ipv4: Fix incorrect route flushing when source address is deleted
...
Eric Dumazet says:
====================
mlx4: better BIG-TCP support
mlx4 uses a bounce buffer in TX whenever the tx descriptors
wrap around the right edge of the ring.
Size of this bounce buffer was hard coded and can be
increased if/when needed.
====================
Link: https://lore.kernel.org/r/20221207141237.2575012-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test against MLX4_MAX_DESC_TXBBS only matters if the TX
bounce buffer is going to be used.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Google production kernel has increased MAX_SKB_FRAGS to 45
for BIG-TCP rollout.
Unfortunately mlx4 TX bounce buffer is not big enough whenever
an skb has up to 45 page fragments.
This can happen often with TCP TX zero copy, as one frag usually
holds 4096 bytes of payload (order-0 page).
Tested:
Kernel built with MAX_SKB_FRAGS=45
ip link set dev eth0 gso_max_size 185000
netperf -t TCP_SENDFILE
I made sure that "ethtool -G eth0 tx 64" was properly working,
ring->full_size being set to 15.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Wei Wang <weiwan@google.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MAX_DESC_SIZE is really the size of the bounce buffer used
when reaching the right side of TX ring buffer.
MAX_DESC_TXBBS get a MLX4_ prefix.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the ice_ptp_wait_for_offest_valid function is scheduled to run while the
driver is resetting, it will exit without completing calibration. The work
function gets scheduled by ice_ptp_port_phy_restart which will be called as
part of the reset recovery process.
It is possible for the first execution to occur before the driver has
completely cleared its resetting flags. Ensure calibration completes by
rescheduling the task until reset is fully completed.
Reported-by: Siddaraju DH <siddaraju.dh@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The Tx and Rx calibration and timestamp generation blocks are independent.
However, the ice driver waits until both blocks are ready before
configuring either block.
This can result in delay of configuring one block because we have not yet
received a packet in the other block.
There is no reason to wait to finish programming Tx just because we haven't
received a packet. Similarly there is no reason to wait to program Rx just
because we haven't transmitted a packet.
Instead of checking both offset status before programming either block,
refactor the ice_phy_cfg_tx_offset_e822 and ice_phy_cfg_rx_offset_e822
functions so that they perform their own offset status checks.
Additionally, make them also check the offset ready bit to determine if
the offset values have already been programmed.
Call the individual configure functions directly in
ice_ptp_wait_for_offset_valid. The functions will now correctly check
status, and program the offsets if ready. Once the offset is programmed,
the functions will exit quickly after just checking the offset ready
register.
Remove the ice_phy_calc_vernier_e822 in ice_ptp_hw.c, as well as the offset
valid check functions in ice_ptp.c entirely as they are no longer
necessary.
With this change, the Tx and Rx blocks will each be enabled as soon as
possible without waiting for the other block to complete calibration. This
can enable timestamps faster in setups which have a low rate of transmitted
or received packets. In particular, it can stop a situation where one port
never receives traffic, and thus never finishes calibration of the Tx
block, resulting in continuous faults reported by the ptp4l daemon
application.
Signed-off-by: Siddaraju DH <siddaraju.dh@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_ptp_flush_tx_tracker function is called to clear all outstanding Tx
timestamp requests when the port is being brought down. This function
iterates over the entire list, but this is unnecessary. We only need to
check the bits which are actually set in the ready bitmap.
Replace this logic with for_each_set_bit, and follow a similar flow as in
ice_ptp_tx_tstamp_cleanup. Note that it is safe to call dev_kfree_skb_any
on a NULL pointer as it will perform a no-op so we do not need to verify
that the skb is actually NULL.
The new implementation also avoids clearing (and thus reading!) the PHY
timestamp unless the index is marked as having a valid timestamp in the
timestamp status bitmap. This ensures that we properly clear the status
registers as appropriate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In the event of a PTP clock time change due to .adjtime or .settime, the
ice driver needs to update the cached copy of the PHC time and also discard
any outstanding Tx timestamps.
This is required because otherwise the wrong copy of the PHC time will be
used when extending the Tx timestamp. This could result in reporting
incorrect timestamps to the stack.
The current approach taken to handle this is to call
ice_ptp_flush_tx_tracker, which will discard any timestamps which are not
yet complete.
This is problematic for two reasons:
1) it could lead to a potential race condition where the wrong timestamp is
associated with a future packet.
This can occur with the following flow:
1. Thread A gets request to transmit a timestamped packet, and picks an
index and transmits the packet
2. Thread B calls ice_ptp_flush_tx_tracker and sees the index in use,
marking is as disarded. No timestamp read occurs because the status
bit is not set, but the index is released for re-use
3. Thread A gets a new request to transmit another timestamped packet,
picks the same (now unused) index and transmits that packet.
4. The PHY transmits the first packet and updates the timestamp slot and
generates an interrupt.
5. The ice_ptp_tx_tstamp thread executes and sees the interrupt and a
valid timestamp but associates it with the new Tx SKB and not the one
that actual timestamp for the packet as expected.
This could result in the previous timestamp being assigned to a new
packet producing incorrect timestamps and leading to incorrect behavior
in PTP applications.
This is most likely to occur when the packet rate for Tx timestamp
requests is very high.
2) on E822 hardware, we must avoid reading a timestamp index more than once
each time its status bit is set and an interrupt is generated by
hardware.
We do have some extensive checks for the unread flag to ensure that only
one of either the ice_ptp_flush_tx_tracker or ice_ptp_tx_tstamp threads
read the timestamp. However, even with this we can still have cases
where we "flush" a timestamp that was actually completed in hardware.
This can lead to cases where we don't read the timestamp index as
appropriate.
To fix both of these issues, we must avoid calling ice_ptp_flush_tx_tracker
outside of the teardown path.
Rather than using ice_ptp_flush_tx_tracker, introduce a new state bitmap,
the stale bitmap. Start this as cleared when we begin a new timestamp
request. When we're about to extend a timestamp and send it up to the
stack, first check to see if that stale bit was set. If so, drop the
timestamp without sending it to the stack.
When we need to update the cached PHC timestamp out of band, just mark all
currently outstanding timestamps as stale. This will ensure that once
hardware completes the timestamp we'll ignore it correctly and avoid
reporting bogus timestamps to userspace.
With this change, we fix potential issues caused by calling
ice_ptp_flush_tx_tracker during normal operation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_ptp_alloc_tx_tracker function must allocate the timestamp array and
the bitmap for tracking the currently in use indexes. A future change is
going to add yet another allocation to this function.
If these allocations fail we need to ensure that we properly cleanup and
ensure that the pointers in the ice_ptp_tx structure are NULL.
Simplify this logic by allocating to local variables first. If any
allocation fails, then free everything and exit. Only update the ice_ptp_tx
structure if all allocations succeed.
This ensures that we have no side effects on the Tx structure unless all
allocations have succeeded. Thus, no code will see an invalid pointer and
we don't need to re-assign NULL on cleanup.
This is safe because kernel "free" functions are designed to be NULL safe
and perform no action if passed a NULL pointer. Thus its safe to simply
always call kfree or bitmap_free even if one of those pointers was NULL.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When requesting a new timestamp, the ice_ptp_request_ts function does not
hold the Tx tracker lock while checking init and calibrating. This means
that we might issue a new timestamp request just after the Tx timestamp
tracker starts being deinitialized. This could lead to incorrect access of
the timestamp structures. Correct this by moving the init and calibrating
checks under the lock, and updating the flows which modify these fields to
use the lock.
Note that we do not need to hold the lock while checking for tx->init in
ice_ptp_tx_tstamp. This is because the teardown function will use
synchronize_irq after clearing the flag to ensure that the threaded
interrupt completes. Either a) the tx->init flag will be cleared before the
ice_ptp_tx_tstamp function starts, thus it will exit immediately, or b) the
threaded interrupt will be executing and the synchronize_irq will wait
until the threaded interrupt has completed at which point we know the init
field has definitely been set and new interrupts will not execute the Tx
timestamp thread function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Saeed Mahameed says:
====================
Support tc police jump conform-exceed attribute
The tc police action conform-exceed option defines how to handle
packets which exceed or conform to the configured bandwidth limit.
One of the possible conform-exceed values is jump, which skips over
a specified number of actions.
This series adds support for conform-exceed jump action.
The series adds platform support for branching actions by providing
true/false flow attributes to the branching action.
This is necessary for supporting police jump, as each branch may
execute a different action list.
The first five patches are preparation patches:
- Patches 1 and 2 add support for actions with no destinations (e.g. drop)
- Patch 3 refactor the code for subsequent function reuse
- Patch 4 defines an abstract way for identifying terminating actions
- Patch 5 updates action list validations logic considering branching actions
The following three patches introduce an interface for abstracting branching
actions:
- Patch 6 introduces an abstract api for defining branching actions
- Patch 7 generically instantiates the branching flow attributes using
the abstract API
Patch 8 adds the platform support for jump actions, by executing the following
sequence:
a. Store the jumping flow attr
b. Identify the jump target action while iterating the actions list.
c. Instantiate a new flow attribute after the jump target action.
This is the flow attribute that the branching action should jump to.
d. Set the target post action id on:
d.1. The jumping attribute, thus realizing the jump functionality.
d.2. The attribute preceding the target jump attr, if not terminating.
The next patches apply the platform's branching attributes to the police
action:
- Patch 9 is a refactor patch
- Patch 10 initializes the post meter table with the red/green flow attributes,
as were initialized by the platform
- Patch 11 enables the offload of meter actions using jump conform-exceed
value.
====================
Link: https://lore.kernel.org/all/20221203221337.29267-1-saeed@kernel.org/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Separate the matchall police action validation from flower validation.
Isolate the action validation logic in the police action parser.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221203221337.29267-12-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instantiate the post meter actions with the platform initialized branching
action attributes.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221203221337.29267-11-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently post meter supports only the pipe/drop conform-exceed policy.
This assumption is reflected in several variable names.
Rename the following variables as a pre-step for using the generalized
branching action platform.
Rename fwd_green_rule/drop_red_rule to green_rule/red_rule respectively.
Repurpose red_counter/green_counter to act_counter/drop_counter to allow
police conform-exceed configurations that do not drop.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221203221337.29267-10-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Identify the jump target action when iterating the action list.
Initialize the jump target attr with the jumping attribute during the
parsing phase. Initialize the jumping attr post action with the target
during the offload phase.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221203221337.29267-9-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Initialize flow attribute for drop, accept, pipe and jump branching actions.
Instantiate a flow attribute instance according to the specified branch
control action. Store the branching attributes on the branching action
flow attribute during the parsing phase. Then, during the offload phase,
allocate the relevant mod header objects to the branching actions.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221203221337.29267-8-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend the act tc api to set the branch control params aligning with
the police conform/exceed use case.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221203221337.29267-7-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the entire flow action list is validate for offload limitations.
For example, flow with both forward and drop actions are declared invalid
due to hardware restrictions.
However, a multi-table hardware model changes the limitations from a flow
scope to a single flow attribute scope.
Apply offload limitations to flow attributes instead of the entire flow.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221203221337.29267-6-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend act api to identify actions that terminate action list.
Pre-step for terminating branching actions.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221203221337.29267-5-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After the tc action parsing phase the flow attribute is initialized with
relevant eswitch offload objects such as tunnel, vlan, header modify and
counter attributes. The post processing is done both for fdb and post-action
attributes.
Reuse the flow attribute post parsing logic by both fdb and post-action
offloads.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221203221337.29267-4-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently create_flow_handle() assumes a null dest pointer when there
are no destinations.
This might not be the case as the caller may pass an allocated dest
array while setting the dest_num parameter to 0.
Assert null dest array for flow rules that have no destinations (e.g. drop
rule).
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221203221337.29267-3-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rules with drop action are not required to have a destination.
Currently the destination list is allocated with the maximum number of
destinations and passed to the fs_core layer along with the actual number
of destinations.
Remove redundant passing of dest pointer when count of dest is 0.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221203221337.29267-2-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=eEFh
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2022120801' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
"A regression fix for handling Logitech HID++ devices and memory
corruption fixes:
- regression fix (revert) for catch-all handling of Logitech HID++
Bluetooth devices; there are devices that turn out not to work with
this, and the root cause is yet to be properly understood. So we
are dropping it for now, and it will be revisited for 6.2 or 6.3
(Benjamin Tissoires)
- memory corruption fix in HID core (ZhangPeng)
- memory corruption fix in hid-lg4ff (Anastasia Belova)
- Kconfig fix for I2C_HID (Benjamin Tissoires)
- a few device-id specific quirks that piggy-back on top of the
important fixes above"
* tag 'for-linus-2022120801' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
Revert "HID: logitech-hidpp: Enable HID++ for all the Logitech Bluetooth devices"
Revert "HID: logitech-hidpp: Remove special-casing of Bluetooth devices"
HID: usbhid: Add ALWAYS_POLL quirk for some mice
HID: core: fix shift-out-of-bounds in hid_report_raw_event
HID: uclogic: Add HID_QUIRK_HIDINPUT_FORCE quirk
HID: fix I2C_HID not selected when I2C_HID_OF_ELAN is
HID: hid-lg4ff: Add check for empty lbuf
HID: ite: Enable QUIRK_TOUCHPAD_ON_OFF_REPORT on Acer Aspire Switch V 10
HID: uclogic: Fix frame templates for big endian architectures
One last build fix came in, addressing a link failure when
building without CONFIG_OUTER_CACHE
-----BEGIN PGP SIGNATURE-----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=5lcR
-----END PGP SIGNATURE-----
Merge tag 'soc-fixes-6.1-5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fix from Arnd Bergmann:
"One last build fix came in, addressing a link failure when building
without CONFIG_OUTER_CACHE"
* tag 'soc-fixes-6.1-5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: at91: fix build for SAMA5D3 w/o L2 cache
This reverts commit 532223c8ac57605a10e46dc0ab23dcf01c9acb43.
As reported in [0], hid-logitech-hidpp now binds on all bluetooth mice,
but there are corner cases where hid-logitech-hidpp just gives up on
the mouse. This leads the end user with a dead mouse.
Given that we are at -rc8, we are definitively too late to find a proper
fix. We already identified 2 issues less than 24 hours after the bug
report. One in that ->match() was never designed to be used anywhere else
than in hid-generic, and the other that hid-logitech-hidpp has corner
cases where it gives up on devices it is not supposed to.
So we have no choice but postpone this patch to the next kernel release.
[0] https://lore.kernel.org/linux-input/CAJZ5v0g-_o4AqMgNwihCb0jrwrcJZfRrX=jv8aH54WNKO7QB8A@mail.gmail.com/
Reported-by: Rafael J . Wysocki <rjw@rjwysocki.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 8544c812e43ab7bdf40458411b83987b8cba924d.
We need to revert commit 532223c8ac57 ("HID: logitech-hidpp: Enable HID++
for all the Logitech Bluetooth devices") because that commit might make
hid-logitech-hidpp bind on mice that are not well enough supported by
hid-logitech-hidpp, and the end result is that the probe of those mice
is now returning -ENODEV, leaving the end user with a dead mouse.
Given that commit 8544c812e43a ("HID: logitech-hidpp: Remove special-casing
of Bluetooth devices") is a direct dependency of 532223c8ac57, revert it
too.
Note that this also adapt according to commit 908d325e1665 ("HID:
logitech-hidpp: Detect hi-res scrolling support") to re-add support of
the devices that were removed from that commit too.
I have locally an MX Master and I tested this device with that revert,
ensuring we still have high-res scrolling.
Reported-by: Rafael J . Wysocki <rjw@rjwysocki.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
