IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Avoid spurious link status logs that may ultimately be wrong; for example,
if the link is set to down with the cable plugged, then the cable is
unplugged and after this the link is set to up, the last new log that is
appearing is incorrectly telling that the link is up.
In order to avoid errors, show link status logs after link_reset
processing, and in order to avoid spurious as much as possible, only show
the link loss when some link status change is detected.
cc: stable@vger.kernel.org
Fixes: e2ca90c276e1 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix unintended sign extension and klockwork issues. These are not real
issue but for sanity checks.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TC queues needs to be correctly updated when the number of queues on
a VSI is reconfigured, so netdev's queue and TC settings will be
dynamically adjusted and could accurately represent the underlying
hardware state after changes to the VSI queue counts.
Fixes: 0754d65bd4be ("ice: Add infrastructure for mqprio support via ndo_setup_tc")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Karen Ostrowska <karen.ostrowska@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE1588(ptp) is optional feature for network. Remove it from required
list to fix below CHECK_DTBS warning.
arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dtb: ethernet@f0000: 'ptp-timer' is a required property
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The errata DS80000754 recommends monitoring potential faults in
half-duplex mode for the KSZ9477 family.
half-duplex is not very common so I just added a critical message
when the fault conditions are detected. The switch can be expected
to be unable to communicate anymore in these states and a software
reset of the switch would be required which I did not implement.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Errata DS80000758 states that carrier sense back pressure mode can cause
link down issues in 100BASE-TX half duplex mode. The datasheet also
recommends to always use the collision based back pressure mode.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Woojung Huh <Woojung.huh@microchip.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY_ID_KSZ9477 was supported but not added to the device table passed to
MODULE_DEVICE_TABLE.
Fixes: fc3973a1fa09 ("phy: micrel: add Microchip KSZ 9477 Switch PHY support")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all PSE attributes are used for the pse-set netlink command.
Select only the ones used by ethtool.
Fixes: f8586411e40e ("netlink: specs: Expand the pse netlink command with PoE interface")
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 types of outstanding tx skb's:
Type 1: Packets that are sitting in the drivers ind_buff that are
waiting to be batch sent to the NIC. During a device reset, these are
freed with a call to ibmvnic_tx_scrq_clean_buffer()
Type 2: Packets that have been sent to the NIC and are awaiting a TX
completion IRQ. These are free'd during a reset with a call to
clean_tx_pools()
During any reset which requires us to free the tx irq, ensure that the
Type 2 skb references are freed. Since the irq is released, it is
impossible for the NIC to inform of any completions.
Furthermore, later in the reset process is a call to init_tx_pools()
which marks every entry in the tx pool as free (ie not outstanding).
So if the driver is to make a call to init_tx_pools(), it must first
be sure that the tx pool is empty of skb references.
This issue was discovered by observing the following in the logs during
EEH testing:
TX free map points to untracked skb (tso_pool 0 idx=4)
TX free map points to untracked skb (tso_pool 0 idx=5)
TX free map points to untracked skb (tso_pool 1 idx=36)
Fixes: 65d6470d139a ("ibmvnic: clean pending indirect buffs during reset")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Don't accept TT entries for out-of-spec VIDs, by Sven Eckelmann
- Revert "batman-adv: prefer kfree_rcu() over call_rcu() with free-only
callbacks", by Linus Lüssing
-----BEGIN PGP SIGNATURE-----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=sCft
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-pullrequest-20240621' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are some batman-adv bugfixes:
- Don't accept TT entries for out-of-spec VIDs, by Sven Eckelmann
- Revert "batman-adv: prefer kfree_rcu() over call_rcu() with free-only
callbacks", by Linus Lüssing
* tag 'batadv-net-pullrequest-20240621' of git://git.open-mesh.org/linux-merge:
Revert "batman-adv: prefer kfree_rcu() over call_rcu() with free-only callbacks"
batman-adv: Don't accept TT entries for out-of-spec VIDs
====================
Link: https://patch.msgid.link/20240621143915.49137-1-sw@simonwunderlich.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEUEC6huC2BN0pvD5fKDiiPnotvG8FAmZ1TY8THG1rbEBwZW5n
dXRyb25peC5kZQAKCRAoOKI+ei28b+pXB/9fsvj/6jQtOAyGUHzKlWLGkfqh199P
ecWVL6/zCrAhS/CtE1VY97+6Khd9Ipmz7wXXE9IpuuIhMrfS0AkGy/9f30Kf59XL
PcehYmmOzNlpEPdqTVYbJGc9gOl1LNUTtTfAtJMilOY4NtvGGr02YT+frKsEKjYe
O/qrE6trjeAV3pHThZzqkVDDeTRP68XuMlx6W6NFduQOmCxB6bLluRMd5yqoV5G6
fLjRV5iwdB1qIU8Ny52NYGYrh0JfRqA97eLpMveTxG06/RCu7/zfAkdVJWfGf5ho
6PtRd7qqAh5uF2EZ5qXlzPc1FRyqFB8uhmavMetQ6g3F3UY6u0xSTVtF
=5bED
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-6.10-20240621' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2024-06-21
The first patch is by Oleksij Rempel, it enhances the error handling
for tightly received RTS message in the j1939 protocol.
Shigeru Yoshida's patch fixes a kernel information leak in
j1939_send_one() in the j1939 protocol.
Followed by a patch by Oleksij Rempel for the j1939 protocol, to
properly recover from a CAN bus error during BAM transmission.
A patch by Chen Ni properly propagates errors in the kvaser_usb
driver.
The last patch is by Vitor Soares, that fixes an infinite loop in the
mcp251xfd driver is SPI async sending fails during xmit.
* tag 'linux-can-fixes-for-6.10-20240621' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: mcp251xfd: fix infinite loop when xmit fails
can: kvaser_usb: fix return value for hif_usb_send_regout
net: can: j1939: recover socket queue on CAN bus error during BAM transmission
net: can: j1939: Initialize unused data in j1939_send_one()
net: can: j1939: enhanced error handling for tightly received RTS messages in xtp_rx_rts_session_new
====================
Link: https://patch.msgid.link/20240621121739.434355-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ensure the inner IP header is part of the skb's linear data before
setting old_iph. Otherwise, on a non-linear skb, old_iph could point
outside of the packet data.
Unlike classical VXLAN, which always encapsulates Ethernet packets,
VXLAN-GPE can transport IP packets directly. In that case, we need to
look at skb->protocol to figure out if an Ethernet header is present.
Fixes: d342894c5d2f ("vxlan: virtual extensible lan")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Link: https://patch.msgid.link/2aa75f6fa62ac9dbe4f16ad5ba75dd04a51d4b99.1718804000.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Petr Machata says:
====================
mlxsw: Fixes
This patchset fixes an issue with mlxsw driver initialization, and a
memory corruption issue in shared buffer occupancy handling.
v3:
- Drop the core thermal fix, it's not relevant anymore.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The following two shared buffer operations make use of the Shared Buffer
Status Register (SBSR):
# devlink sb occupancy snapshot pci/0000:01:00.0
# devlink sb occupancy clearmax pci/0000:01:00.0
The register has two masks of 256 bits to denote on which ingress /
egress ports the register should operate on. Spectrum-4 has more than
256 ports, so the register was extended by cited commit with a new
'port_page' field.
However, when filling the register's payload, the driver specifies the
ports as absolute numbers and not relative to the first port of the port
page, resulting in memory corruptions [1].
Fix by specifying the ports relative to the first port of the port page.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_sb_occ_snapshot+0xb6d/0xbc0
Read of size 1 at addr ffff8881068cb00f by task devlink/1566
[...]
Call Trace:
<TASK>
dump_stack_lvl+0xc6/0x120
print_report+0xce/0x670
kasan_report+0xd7/0x110
mlxsw_sp_sb_occ_snapshot+0xb6d/0xbc0
mlxsw_devlink_sb_occ_snapshot+0x75/0xb0
devlink_nl_sb_occ_snapshot_doit+0x1f9/0x2a0
genl_family_rcv_msg_doit+0x20c/0x300
genl_rcv_msg+0x567/0x800
netlink_rcv_skb+0x170/0x450
genl_rcv+0x2d/0x40
netlink_unicast+0x547/0x830
netlink_sendmsg+0x8d4/0xdb0
__sys_sendto+0x49b/0x510
__x64_sys_sendto+0xe5/0x1c0
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
[...]
Allocated by task 1:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x8f/0xa0
copy_verifier_state+0xbc2/0xfb0
do_check_common+0x2c51/0xc7e0
bpf_check+0x5107/0x9960
bpf_prog_load+0xf0e/0x2690
__sys_bpf+0x1a61/0x49d0
__x64_sys_bpf+0x7d/0xc0
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 1:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3b/0x60
poison_slab_object+0x109/0x170
__kasan_slab_free+0x14/0x30
kfree+0xca/0x2b0
free_verifier_state+0xce/0x270
do_check_common+0x4828/0xc7e0
bpf_check+0x5107/0x9960
bpf_prog_load+0xf0e/0x2690
__sys_bpf+0x1a61/0x49d0
__x64_sys_bpf+0x7d/0xc0
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Fixes: f8538aec88b4 ("mlxsw: Add support for more than 256 ports in SBSR register")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cited commit added support for a new reset flow ("all reset") which is
deeper than the existing reset flow ("software reset") and allows the
device's PCI firmware to be upgraded.
In the new flow the driver first tells the firmware that "all reset" is
required by issuing a new reset command (i.e., MRSR.command=6) and then
triggers the reset by having the PCI core issue a secondary bus reset
(SBR).
However, due to a race condition in the device's firmware the device is
not always able to recover from this reset, resulting in initialization
failures [1].
New firmware versions include a fix for the bug and advertise it using a
new capability bit in the Management Capabilities Mask (MCAM) register.
Avoid initialization failures by reading the new capability bit and
triggering the new reset flow only if the bit is set. If the bit is not
set, trigger a normal PCI hot reset by skipping the call to the
Management Reset and Shutdown Register (MRSR).
Normal PCI hot reset is weaker than "all reset", but it results in a
fully operational driver and allows users to flash a new firmware, if
they want to.
[1]
mlxsw_spectrum4 0000:01:00.0: not ready 1023ms after bus reset; waiting
mlxsw_spectrum4 0000:01:00.0: not ready 2047ms after bus reset; waiting
mlxsw_spectrum4 0000:01:00.0: not ready 4095ms after bus reset; waiting
mlxsw_spectrum4 0000:01:00.0: not ready 8191ms after bus reset; waiting
mlxsw_spectrum4 0000:01:00.0: not ready 16383ms after bus reset; waiting
mlxsw_spectrum4 0000:01:00.0: not ready 32767ms after bus reset; waiting
mlxsw_spectrum4 0000:01:00.0: not ready 65535ms after bus reset; giving up
mlxsw_spectrum4 0000:01:00.0: PCI function reset failed with -25
mlxsw_spectrum4 0000:01:00.0: cannot register bus device
mlxsw_spectrum4: probe of 0000:01:00.0 failed with error -25
Fixes: f257c73e5356 ("mlxsw: pci: Add support for new reset flow")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Maksym Yaremchuk <maksymy@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diag_uid selftest failed on NIPA where the received nlmsg_type is
NLMSG_ERROR [0] because CONFIG_UNIX_DIAG is not set [1] by default
and sock_diag_lock_handler() failed to load the module.
# # Starting 2 tests from 2 test cases.
# # RUN diag_uid.uid.1 ...
# # diag_uid.c:159:1:Expected nlh->nlmsg_type (2) == SOCK_DIAG_BY_FAMILY (20)
# # 1: Test terminated by assertion
# # FAIL diag_uid.uid.1
# not ok 1 diag_uid.uid.1
Let's add all AF_UNIX Kconfig to the config file under af_unix dir
so that NIPA consumes it.
Fixes: ac011361bd4f ("af_unix: Add test for sock_diag and UDIAG_SHOW_UID.")
Link: https://netdev-3.bots.linux.dev/vmksft-net/results/644841/104-diag-uid/stdout [0]
Link: https://netdev-3.bots.linux.dev/vmksft-net/results/644841/config [1]
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/netdev/20240617073033.0cbb829d@kernel.org/
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our corporate overlords have been changing the domains around
again and this mailing list has gone away.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Selecting FW_UPLOAD is not sufficient as it allows the firmware loader
API to be built as a module alongside the pd692x0 driver built as builtin.
Add select FW_LOADER to fix this issue.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202406200632.hSChnX0g-lkp@intel.com/
Fixes: 9a9938451890 ("net: pse-pd: Add PD692x0 PSE controller driver")
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __ethtool_get_ts_info function returns directly if the device has a
get_ts_info() method. For bonding with an active slave, this works correctly
as we simply return the real device's timestamping information. However,
when there is no active slave, we only check the slave's TX software
timestamp information. We still need to set the phc index and RX timestamp
information manually. Otherwise, the result will be look like:
Time stamping parameters for bond0:
Capabilities:
software-transmit
PTP Hardware Clock: 0
Hardware Transmit Timestamp Modes: none
Hardware Receive Filter Modes: none
This issue does not affect VLAN or MACVLAN devices, as they only have one
downlink and can directly use the downlink's timestamping information.
Fixes: b8768dc40777 ("net: ethtool: Refactor identical get_ts_info implementations.")
Reported-by: Liang Li <liali@redhat.com>
Closes: https://issues.redhat.com/browse/RHEL-42409
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fill this in so user-space can identify multiple ports on the same CP
unit.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilya found a failure in running check-kernel tests with at_groups=144
(144: conntrack - FTP SNAT orig tuple) in OVS repo. After his further
investigation, the root cause is that the labels sent to userspace
for related ct are incorrect.
The labels for unconfirmed related ct should use its master's labels.
However, the changes made in commit 8c8b73320805 ("openvswitch: set
IPS_CONFIRMED in tmpl status only when commit is set in conntrack")
led to getting labels from this related ct.
So fix it in ovs_ct_get_labels() by changing to copy labels from its
master ct if it is a unconfirmed related ct. Note that there is no
fix needed for ct->mark, as it was already copied from its master
ct for related ct in init_conntrack().
Fixes: 8c8b73320805 ("openvswitch: set IPS_CONFIRMED in tmpl status only when commit is set in conntrack")
Reported-by: Ilya Maximets <i.maximets@ovn.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Ilya Maximets <i.maximets@ovn.org>
Tested-by: Ilya Maximets <i.maximets@ovn.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mcp251xfd_start_xmit() function fails, the driver stops
processing messages, and the interrupt routine does not return,
running indefinitely even after killing the running application.
Error messages:
[ 441.298819] mcp251xfd spi2.0 can0: ERROR in mcp251xfd_start_xmit: -16
[ 441.306498] mcp251xfd spi2.0 can0: Transmit Event FIFO buffer not empty. (seq=0x000017c7, tef_tail=0x000017cf, tef_head=0x000017d0, tx_head=0x000017d3).
... and repeat forever.
The issue can be triggered when multiple devices share the same SPI
interface. And there is concurrent access to the bus.
The problem occurs because tx_ring->head increments even if
mcp251xfd_start_xmit() fails. Consequently, the driver skips one TX
package while still expecting a response in
mcp251xfd_handle_tefif_one().
Resolve the issue by starting a workqueue to write the tx obj
synchronously if err = -EBUSY. In case of another error, decrement
tx_ring->head, remove skb from the echo stack, and drop the message.
Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Cc: stable@vger.kernel.org
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Link: https://lore.kernel.org/all/20240517134355.770777-1-ivitro@gmail.com
[mkl: use more imperative wording in patch description]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As the potential failure of usb_submit_urb(), it should be better to
return the err variable to catch the error.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://lore.kernel.org/all/20240521041020.1519416-1-nichen@iscas.ac.cn
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Addresses an issue where a CAN bus error during a BAM transmission
could stall the socket queue, preventing further transmissions even
after the bus error is resolved. The fix activates the next queued
session after the error recovery, allowing communication to continue.
Fixes: 9d71dd0c70099 ("can: add support of SAE J1939 protocol")
Cc: stable@vger.kernel.org
Reported-by: Alexander Hölzl <alexander.hoelzl@gmx.net>
Tested-by: Alexander Hölzl <alexander.hoelzl@gmx.net>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20240528070648.1947203-1-o.rempel@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch enhances error handling in scenarios with RTS (Request to
Send) messages arriving closely. It replaces the less informative WARN_ON_ONCE
backtraces with a new error handling method. This provides clearer error
messages and allows for the early termination of problematic sessions.
Previously, sessions were only released at the end of j1939_xtp_rx_rts().
Potentially this could be reproduced with something like:
testj1939 -r vcan0:0x80 &
while true; do
# send first RTS
cansend vcan0 18EC8090#1014000303002301;
# send second RTS
cansend vcan0 18EC8090#1014000303002301;
# send abort
cansend vcan0 18EC8090#ff00000000002301;
done
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Reported-by: syzbot+daa36413a5cedf799ae4@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20231117124959.961171-1-o.rempel@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The very first flush in any port will flush all learned addresses in all
ports. This can be observed by unplugging the cable from one port while
additional ports are connected and dumping the fdb entries.
This problem is caused by the initially wrong value programmed to the
REG_SW_LUE_CTRL_1 register. Setting SW_FLUSH_STP_TABLE and
SW_FLUSH_MSTP_TABLE bits does not have an immediate effect. It is when
ksz9477_flush_dyn_mac_table() is called then the SW_FLUSH_STP_TABLE bit
takes effect and flushes all learned entries. After that call both bits
are reset and so the next port flush will not cause such problem again.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://patch.msgid.link/1718756202-2731-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current release - regressions:
- ipv6: bring NLM_DONE out to a separate recv() again
Current release - new code bugs:
- wifi: cfg80211: wext: set ssids=NULL for passive scans via old wext API
Previous releases - regressions:
- wifi: mac80211: fix monitor channel setting with chanctx emulation
(probably most awaited of the fixes in this PR, tracked by Thorsten)
- usb: ax88179_178a: bring back reset on init, if PHY is disconnected
- bpf: fix UML x86_64 compile failure with BPF
- bpf: avoid splat in pskb_pull_reason(), sanity check added can be hit
with malicious BPF
- eth: mvpp2: use slab_build_skb() for packets in slab, driver was
missed during API refactoring
- wifi: iwlwifi: add missing unlock of mvm mutex
Previous releases - always broken:
- ipv6: add a number of missing null-checks for in6_dev_get(), in case
IPv6 disabling races with the datapath
- bpf: fix reg_set_min_max corruption of fake_reg
- sched: act_ct: add netns as part of the key of tcf_ct_flow_table
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Lb9b
-----END PGP SIGNATURE-----
Merge tag 'net-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless, bpf and netfilter.
Happy summer solstice! The line count is a bit inflated by a selftest
and update to a driver's FW interface header, in reality this is
slightly below average for us. We are expecting one driver fix from
Intel, but there are no big known issues.
Current release - regressions:
- ipv6: bring NLM_DONE out to a separate recv() again
Current release - new code bugs:
- wifi: cfg80211: wext: set ssids=NULL for passive scans via old wext API
Previous releases - regressions:
- wifi: mac80211: fix monitor channel setting with chanctx emulation
(probably most awaited of the fixes in this PR, tracked by Thorsten)
- usb: ax88179_178a: bring back reset on init, if PHY is disconnected
- bpf: fix UML x86_64 compile failure with BPF
- bpf: avoid splat in pskb_pull_reason(), sanity check added can be hit
with malicious BPF
- eth: mvpp2: use slab_build_skb() for packets in slab, driver was
missed during API refactoring
- wifi: iwlwifi: add missing unlock of mvm mutex
Previous releases - always broken:
- ipv6: add a number of missing null-checks for in6_dev_get(), in case
IPv6 disabling races with the datapath
- bpf: fix reg_set_min_max corruption of fake_reg
- sched: act_ct: add netns as part of the key of tcf_ct_flow_table"
* tag 'net-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (63 commits)
net: usb: rtl8150 fix unintiatilzed variables in rtl8150_get_link_ksettings
selftests: virtio_net: add forgotten config options
bnxt_en: Restore PTP tx_avail count in case of skb_pad() error
bnxt_en: Set TSO max segs on devices with limits
bnxt_en: Update firmware interface to 1.10.3.44
net: stmmac: Assign configured channel value to EXTTS event
net: do not leave a dangling sk pointer, when socket creation fails
net/tcp_ao: Don't leak ao_info on error-path
ice: Fix VSI list rule with ICE_SW_LKUP_LAST type
ipv6: bring NLM_DONE out to a separate recv() again
selftests: add selftest for the SRv6 End.DX6 behavior with netfilter
selftests: add selftest for the SRv6 End.DX4 behavior with netfilter
netfilter: move the sysctl nf_hooks_lwtunnel into the netfilter core
seg6: fix parameter passing when calling NF_HOOK() in End.DX4 and End.DX6 behaviors
netfilter: ipset: Fix suspicious rcu_dereference_protected()
selftests: openvswitch: Set value to nla flags.
octeontx2-pf: Fix linking objects into multiple modules
octeontx2-pf: Add error handling to VLAN unoffload handling
virtio_net: fixing XDP for fully checksummed packets handling
virtio_net: checksum offloading handling fix
...
Lots of small HD-audio quirks and fixes (mostly Realtek codec and
Cirrus stuff). Also a small MIDI 2.0 fix and a fix for missing
module description are included.
-----BEGIN PGP SIGNATURE-----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=E//p
-----END PGP SIGNATURE-----
Merge tag 'sound-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Lots of small HD-audio quirks and fixes (mostly Realtek codec and
Cirrus stuff).
Also a small MIDI 2.0 fix and a fix for missing module description
are included"
* tag 'sound-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda: cs35l56: Select SERIAL_MULTI_INSTANTIATE
ALSA: hda/realtek: Add more codec ID to no shutup pins list
sound/oss/dmasound: add missing MODULE_DESCRIPTION() macro
ALSA: hda/realtek: Add quirk for Lenovo Yoga Pro 7 14ARP8
ALSA: hda/realtek: Enable headset mic on IdeaPad 330-17IKB 81DM
ALSA: hda: tas2781: Component should be unbound before deconstruction
ALSA: hda: cs35l41: Component should be unbound before deconstruction
ALSA: hda: cs35l56: Component should be unbound before deconstruction
ALSA/hda: intel-dsp-config: Document AVS as dsp_driver option
ALSA: hda/realtek: Support Lenovo Thinkbook 13x Gen 4
ALSA: hda/realtek: Support Lenovo Thinkbook 16P Gen 5
ALSA: hda: cs35l41: Support Lenovo Thinkbook 13x Gen 4
ALSA: hda: cs35l41: Support Lenovo Thinkbook 16P Gen 5
ALSA: hda/realtek: Remove Framework Laptop 16 from quirks
ALSA: hda/realtek: Limit mic boost on N14AP7
ALSA: hda/realtek: fix mute/micmute LEDs don't work for ProBook 445/465 G11.
ALSA: seq: ump: Fix missing System Reset message handling
ALSA: hda: cs35l41: Possible null pointer dereference in cs35l41_hda_unbind()
ALSA: hda: cs35l56: Fix lifecycle of codec pointer
- Fix AXP717 PMIC probe and by extension it's consumers
-----BEGIN PGP SIGNATURE-----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=KVSG
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull mfd fix from Lee Jones:
- Fix AXP717 PMIC probe and by extension its consumers
* tag 'mfd-fixes-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: axp20x: AXP717: Fix missing IRQ status registers range
One may use tools/testing/selftests/drivers/net/virtio_net/config
for example for vng build command like this one:
$ vng -v -b -f tools/testing/selftests/drivers/net/virtio_net/config
In that case, the needed kernel config options are not turned on.
Add the missed kernel config options.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/netdev/20240617072614.75fe79e7@kernel.org/
Reported-by: Matthieu Baerts <matttbe@kernel.org>
Closes: https://lore.kernel.org/netdev/1a63f209-b1d4-4809-bc30-295a5cafa296@kernel.org/
Fixes: ccfaed04db5e ("selftests: virtio_net: add initial tests")
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20240619061748.1869404-1-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Chan says:
====================
bnxt_en: Bug fixes for net
The first firmware interface update is needed by the second patch to
limit the number of TSO segments on the 5760X chips. The third patch
fixes the TX error path for PTP packets.
====================
Link: https://lore.kernel.org/r/20240618215313.29631-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current code only restores PTP tx_avail count when we get DMA
mapping errors. Fix it so that the PTP tx_avail count will be
restored for both DMA mapping errors and skb_pad() errors.
Otherwise PTP TX timestamp will not be available after a PTP
packet hits the skb_pad() error.
Fixes: 83bb623c968e ("bnxt_en: Transmit and retrieve packet timestamps")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240618215313.29631-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Firmware will now advertise a non-zero TSO max segments if the
device has a limit. 0 means no limit. The latest 5760X chip
(early revs) has a limit of 2047 that cannot be exceeded. If
exceeded, the chip will send out just a small number of segments.
Call netif_set_tso_max_segs() if the device has a limit.
Fixes: 2012a6abc876 ("bnxt_en: Add 5760X (P7) PCI IDs")
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240618215313.29631-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The relevant change is the max_tso_segs value returned by firmware
in the HWRM_FUNC_QCAPS response. This value will be used in the next
patch to cap the TSO segments.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240618215313.29631-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Assign the configured channel value to the EXTTS event in the timestamp
interrupt handler. Without assigning the correct channel, applications
like ts2phc will refuse to accept the event, resulting in errors such
as:
...
ts2phc[656.834]: config item end1.ts2phc.pin_index is 0
ts2phc[656.834]: config item end1.ts2phc.channel is 3
ts2phc[656.834]: config item end1.ts2phc.extts_polarity is 2
ts2phc[656.834]: config item end1.ts2phc.extts_correction is 0
...
ts2phc[656.862]: extts on unexpected channel
ts2phc[658.141]: extts on unexpected channel
ts2phc[659.140]: extts on unexpected channel
Fixes: f4da56529da60 ("net: stmmac: Add support for external trigger timestamping")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://lore.kernel.org/r/20240618073821.619751-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=hdot
-----END PGP SIGNATURE-----
Merge tag 'nf-24-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
Patch #1 fixes the suspicious RCU usage warning that resulted from the
recent fix for the race between namespace cleanup and gc in
ipset left out checking the pernet exit phase when calling
rcu_dereference_protected(), from Jozsef Kadlecsik.
Patch #2 fixes incorrect input and output netdevice in SRv6 prerouting
hooks, from Jianguo Wu.
Patch #3 moves nf_hooks_lwtunnel sysctl toggle to the netfilter core.
The connection tracking system is loaded on-demand, this
ensures availability of this knob regardless.
Patch #4-#5 adds selftests for SRv6 netfilter hooks also from Jianguo Wu.
netfilter pull request 24-06-19
* tag 'nf-24-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
selftests: add selftest for the SRv6 End.DX6 behavior with netfilter
selftests: add selftest for the SRv6 End.DX4 behavior with netfilter
netfilter: move the sysctl nf_hooks_lwtunnel into the netfilter core
seg6: fix parameter passing when calling NF_HOOK() in End.DX4 and End.DX6 behaviors
netfilter: ipset: Fix suspicious rcu_dereference_protected()
====================
Link: https://lore.kernel.org/r/20240619170537.2846-1-pablo@netfilter.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ACPI IDs used in the CS35L56 HDA drivers are all handled by the
serial multi-instantiate driver which starts multiple Linux device
instances from a single ACPI Device() node.
As serial multi-instantiate is not an optional part of the system add it
as a dependency in Kconfig so that it is not overlooked.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Link: https://lore.kernel.org/20240619161602.117452-1-simont@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adding/updating VSI list rule, as well as allocating/freeing VSI list
resource are called several times with type ICE_SW_LKUP_LAST, which fails
because ice_update_vsi_list_rule() and ice_aq_alloc_free_vsi_list()
consider it invalid. Allow calling these functions with ICE_SW_LKUP_LAST.
This fixes at least one issue in switchdev mode, where the same rule with
different action cannot be added, e.g.:
tc filter add dev $PF1 ingress protocol arp prio 0 flower skip_sw \
dst_mac ff:ff:ff:ff:ff:ff action mirred egress redirect dev $VF1_PR
tc filter add dev $PF1 ingress protocol arp prio 0 flower skip_sw \
dst_mac ff:ff:ff:ff:ff:ff action mirred egress redirect dev $VF2_PR
Fixes: 0f94570d0cae ("ice: allow adding advanced rules")
Suggested-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240618210206.981885-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit under Fixes optimized the number of recv() calls
needed during RTM_GETROUTE dumps, but we got multiple
reports of applications hanging on recv() calls.
Applications expect that a route dump will be terminated
with a recv() reading an individual NLM_DONE message.
Coalescing NLM_DONE is perfectly legal in netlink,
but even tho reporters fixed the code in respective
projects, chances are it will take time for those
applications to get updated. So revert to old behavior
(for now)?
This is an IPv6 version of commit 460b0d33cf10 ("inet: bring
NLM_DONE out to a separate recv() again").
Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Link: https://lore.kernel.org/all/CANP3RGc1RG71oPEBXNx_WZFP9AyphJefdO4paczN92n__ds4ow@mail.gmail.com
Reported-by: Stefano Brivio <sbrivio@redhat.com>
Link: https://lore.kernel.org/all/20240315124808.033ff58d@elisabeth
Reported-by: Ilya Maximets <i.maximets@ovn.org>
Link: https://lore.kernel.org/all/02b50aae-f0e9-47a4-8365-a977a85975d3@ovn.org
Fixes: 5fc68320c1fb ("ipv6: remove RTNL protection from inet6_dump_fib()")
Tested-by: Ilya Maximets <i.maximets@ovn.org>
Link: https://lore.kernel.org/r/20240618193914.561782-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Restrict gen-API tests for synthetic and kprobe events to only be built as
modules, as they generate dynamic events that cannot be removed, causing
ftracetest and startup selftests to fail.
-----BEGIN PGP SIGNATURE-----
iQFPBAABCgA5FiEEh7BulGwFlgAOi5DV2/sHvwUrPxsFAmZy6HobHG1hc2FtaS5o
aXJhbWF0c3VAZ21haWwuY29tAAoJENv7B78FKz8bqtYIAMLap5hV/w9Gh5b32hOF
/FS/oqGTIs8wfvZq2PBOruFmmvhrqjvpbZVTU9aNUr2lywYALM+jgO3ElSLIoZdz
5s8Wsnic5a2DvG23r/S5u80f85Gxy14e5fvCcCT/3Bvw1ip65XdMXqUwh9oM4zHh
i8rmeIIJmVspHD9bxTREsosB8/LKvSx6GNzLrHwHyL5UepDgj/r5hLvyEuY3fyuo
hazbvsZbHi+aduAS3it+BnhMoFLgLzqrYi8dl1fPY+xmnGI2LZZkds1mfD1JmjBB
AVm9gOWKpW+HHoxeMEMcAs8mhithR7VGA2V2zdsOmRzndytKhUghHWvgcrBZWvl6
D5Y=
=BNpD
-----END PGP SIGNATURE-----
Merge tag 'probes-fixes-v6.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull probes fix from Masami Hiramatsu:
- Restrict gen-API tests for synthetic and kprobe events to only be
built as modules, as they generate dynamic events that cannot be
removed, causing ftracetest and startup selftests to fail
* tag 'probes-fixes-v6.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Build event generation tests only as modules
this selftest is designed for evaluating the SRv6 End.DX6 behavior
used with netfilter(rpfilter), in this example, for implementing
IPv6 L3 VPN use cases.
Signed-off-by: Jianguo Wu <wujianguo@chinatelecom.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
this selftest is designed for evaluating the SRv6 End.DX4 behavior
used with netfilter(rpfilter), in this example, for implementing
IPv4 L3 VPN use cases.
Signed-off-by: Jianguo Wu <wujianguo@chinatelecom.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Jose Ignacio Tornos Martinez
Ratheesh Kannoth
Jan Sokolowski
Frank Li
David S. Miller
Enguerrand de Ribaucourt
Kory Maincent
Nick Child
Jakub Kicinski
Guillaume Nault
Ido Schimmel
Kuniyuki Iwashima
Shannon Nelson
Eric Dumazet
Taehee Yoo
Hangbin Liu
Aryan Srivastava
Xin Long
Vitor Soares
Chen Ni
Oleksij Rempel
Shigeru Yoshida
Tristram Ha
Linus Torvalds
Oliver Neukum
Jiri Pirko
Pavan Chebbi
Michael Chan
Paolo Abeni
Ignat Korchagin
Simon Trimmer
Dmitry Safonov
Marcin Szycik
Jianguo Wu