IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit ec2a29593c83ed71a7f16e3243941ebfcf75fdf6 ]
5fdc7db644 ("module: setup load info before module_sig_check()")
moved the ELF setup, so that it was done before the signature
check. This made the module name available to signature error
messages.
However, the checks for ELF correctness in setup_load_info
are not sufficient to prevent bad memory references due to
corrupted offset fields, indices, etc.
So, there's a regression in behavior here: a corrupt and unsigned
(or badly signed) module, which might previously have been rejected
immediately, can now cause an oops/crash.
Harden ELF handling for module loading by doing the following:
- Move the signature check back up so that it comes before ELF
initialization. It's best to do the signature check to see
if we can trust the module, before using the ELF structures
inside it. This also makes checks against info->len
more accurate again, as this field will be reduced by the
length of the signature in mod_check_sig().
The module name is now once again not available for error
messages during the signature check, but that seems like
a fair tradeoff.
- Check if sections have offset / size fields that at least don't
exceed the length of the module.
- Check if sections have section name offsets that don't fall
outside the section name table.
- Add a few other sanity checks against invalid section indices,
etc.
This is not an exhaustive consistency check, but the idea is to
at least get through the signature and blacklist checks without
crashing because of corrupted ELF info, and to error out gracefully
for most issues that would have caused problems later on.
Fixes: 5fdc7db6448a ("module: setup load info before module_sig_check()")
Signed-off-by: Frank van der Linden <fllinden@amazon.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10ccd1abb808599a6dc7c9389560016ea3568085 ]
Let's move the common handling of the non-fatal errors after the *switch*
statement -- this avoids *goto*s inside that *switch*...
Suggested-by: Joe Perches <joe@perches.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 705e9195187d85249fbb0eaa844b1604a98fbc9a ]
The 'reason' variable in module_sig_check() points to 3 strings across
the *switch* statement, all needlessly starting with the same text.
Let's put the starting text into the pr_notice() call -- it saves 21
bytes of the object code (x86 gcc 10.2.1).
Suggested-by: Joe Perches <joe@perches.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9f35f634e099894f4d6c3b039cd3de5281ee637 ]
It is useful to know which module failed signature verification, so
print the module name along with the error message.
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcc32f4f183ab8479041b23a1525d48233df1d43 ]
This reverts commit 6af1799aaf3f1bc8defedddfa00df3192445bbf3.
Commit 6af1799aaf3f ("ipv6: drop incoming packets having a v4mapped
source address") introduced an input check against v4mapped addresses.
Use of such addresses on the wire is indeed questionable and not
allowed on public Internet. As the commit pointed out
https://tools.ietf.org/html/draft-itojun-v6ops-v4mapped-harmful-02
lists potential issues.
Unfortunately there are applications which use v4mapped addresses,
and breaking them is a clear regression. For example v4mapped
addresses (or any semi-valid addresses, really) may be used
for uni-direction event streams or packet export.
Since the issue which sparked the addition of the check was with
TCP and request_socks in particular push the check down to TCPv6
and DCCP. This restores the ability to receive UDPv6 packets with
v4mapped address as the source.
Keep using the IPSTATS_MIB_INHDRERRORS statistic to minimize the
user-visible changes.
Fixes: 6af1799aaf3f ("ipv6: drop incoming packets having a v4mapped source address")
Reported-by: Sunyi Shao <sunyishao@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f935e8e72ec28dddb2dc0650b3b6626a293d94b ]
For AF_VSOCK, accept() currently returns sockets that are unlabelled.
Other socket families derive the child's SID from the SID of the parent
and the SID of the incoming packet. This is typically done as the
connected socket is placed in the queue that accept() removes from.
Reuse the existing 'security_sk_clone' hook to copy the SID from the
parent (server) socket to the child. There is no packet SID in this
case.
Fixes: d021c344051a ("VSOCK: Introduce VM Sockets")
Signed-off-by: David Brazdil <dbrazdil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a846738f8c3788d846ed1f587270d2f2e3d32432 upstream.
The fix for XSA-365 zapped too many of the ->persistent_gnt[] entries.
Ones successfully obtained should not be overwritten, but instead left
for xen_blkbk_unmap_prepare() to pick up and put.
This is XSA-371.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Wei Liu <wl@xen.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d7047ed6b7214fbabc16d8712a822e256b1aa44 upstream.
In commit 6417f03132a6 ("module: remove never implemented
MODULE_SUPPORTED_DEVICE") the MODULE_SUPPORTED_DEVICE macro was
removed from the kerne entirely. Shortly before this patch was applied
mainline the commit 59ec7b89ed3e ("can: peak_usb: add forgotten
supported devices") was added to net/master. As this would result in a
merge conflict, let's revert this patch.
Fixes: 59ec7b89ed3e ("can: peak_usb: add forgotten supported devices")
Link: https://lore.kernel.org/r/20210320192649.341832-1-mkl@pengutronix.de
Suggested-by: Leon Romanovsky <leon@kernel.org>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 163f0ec1df33cf468509ff38cbcbb5eb0d7fac60 upstream.
Syzbot is reporting that ext4 can enter fs reclaim from kvmalloc() while
the transaction is started like:
fs_reclaim_acquire+0x117/0x150 mm/page_alloc.c:4340
might_alloc include/linux/sched/mm.h:193 [inline]
slab_pre_alloc_hook mm/slab.h:493 [inline]
slab_alloc_node mm/slub.c:2817 [inline]
__kmalloc_node+0x5f/0x430 mm/slub.c:4015
kmalloc_node include/linux/slab.h:575 [inline]
kvmalloc_node+0x61/0xf0 mm/util.c:587
kvmalloc include/linux/mm.h:781 [inline]
ext4_xattr_inode_cache_find fs/ext4/xattr.c:1465 [inline]
ext4_xattr_inode_lookup_create fs/ext4/xattr.c:1508 [inline]
ext4_xattr_set_entry+0x1ce6/0x3780 fs/ext4/xattr.c:1649
ext4_xattr_ibody_set+0x78/0x2b0 fs/ext4/xattr.c:2224
ext4_xattr_set_handle+0x8f4/0x13e0 fs/ext4/xattr.c:2380
ext4_xattr_set+0x13a/0x340 fs/ext4/xattr.c:2493
This should be impossible since transaction start sets PF_MEMALLOC_NOFS.
Add some assertions to the code to catch if something isn't working as
expected early.
Link: https://lore.kernel.org/linux-ext4/000000000000563a0205bafb7970@google.com/
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20210222171626.21884-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d45c36bafb94e72fdb6dee437279b61b6d97e706 upstream.
The bcm_sf2 driver uses the b53 driver as a library but does not make
usre of the b53_setup() function, this made it fail to inherit the
vlan_filtering_is_global attribute. Fix this by moving the assignment to
b53_switch_alloc() which is used by bcm_sf2.
Fixes: 7228b23e68f7 ("net: dsa: b53: Let DSA handle mismatched VLAN filtering settings")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a5ca857079ea022e0b1b17fc154f7ad7dbc150f upstream.
When a non-initial netns is destroyed, the usual policy is to delete
all virtual network interfaces contained, but move physical interfaces
back to the initial netns. This keeps the physical interface visible
on the system.
CAN devices are somewhat special, as they define rtnl_link_ops even
if they are physical devices. If a CAN interface is moved into a
non-initial netns, destroying that netns lets the interface vanish
instead of moving it back to the initial netns. default_device_exit()
skips CAN interfaces due to having rtnl_link_ops set. Reproducer:
ip netns add foo
ip link set can0 netns foo
ip netns delete foo
WARNING: CPU: 1 PID: 84 at net/core/dev.c:11030 ops_exit_list+0x38/0x60
CPU: 1 PID: 84 Comm: kworker/u4:2 Not tainted 5.10.19 #1
Workqueue: netns cleanup_net
[<c010e700>] (unwind_backtrace) from [<c010a1d8>] (show_stack+0x10/0x14)
[<c010a1d8>] (show_stack) from [<c086dc10>] (dump_stack+0x94/0xa8)
[<c086dc10>] (dump_stack) from [<c086b938>] (__warn+0xb8/0x114)
[<c086b938>] (__warn) from [<c086ba10>] (warn_slowpath_fmt+0x7c/0xac)
[<c086ba10>] (warn_slowpath_fmt) from [<c0629f20>] (ops_exit_list+0x38/0x60)
[<c0629f20>] (ops_exit_list) from [<c062a5c4>] (cleanup_net+0x230/0x380)
[<c062a5c4>] (cleanup_net) from [<c0142c20>] (process_one_work+0x1d8/0x438)
[<c0142c20>] (process_one_work) from [<c0142ee4>] (worker_thread+0x64/0x5a8)
[<c0142ee4>] (worker_thread) from [<c0148a98>] (kthread+0x148/0x14c)
[<c0148a98>] (kthread) from [<c0100148>] (ret_from_fork+0x14/0x2c)
To properly restore physical CAN devices to the initial netns on owning
netns exit, introduce a flag on rtnl_link_ops that can be set by drivers.
For CAN devices setting this flag, default_device_exit() considers them
non-virtual, applying the usual namespace move.
The issue was introduced in the commit mentioned below, as at that time
CAN devices did not have a dellink() operation.
Fixes: e008b5fc8dc7 ("net: Simplfy default_device_exit and improve batching.")
Link: https://lore.kernel.org/r/20210302122423.872326-1-martin@strongswan.org
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8249d17d3194eac064a8ca5bc5ca0abc86feecde upstream.
The pfn variable contains the page frame number as returned by the
pXX_pfn() functions, shifted to the right by PAGE_SHIFT to remove the
page bits. After page protection computations are done to it, it gets
shifted back to the physical address using page_level_shift().
That is wrong, of course, because that function determines the shift
length based on the level of the page in the page table but in all the
cases, it was shifted by PAGE_SHIFT before.
Therefore, shift it back using PAGE_SHIFT to get the correct physical
address.
[ bp: Rewrite commit message. ]
Fixes: dfaaec9033b8 ("x86: Add support for changing memory encryption attribute in early boot")
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/81abbae1657053eccc535c16151f63cd049dcb97.1616098294.git.isaku.yamahata@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 291da9d4a9eb3a1cb0610b7f4480f5b52b1825e7 upstream.
If CONFIG_DEBUG_LOCK_ALLOC=n then mutex_lock_io_nested() maps to
mutex_lock() which is clearly wrong because mutex_lock() lacks the
io_schedule_prepare()/finish() invocations.
Map it to mutex_lock_io().
Fixes: f21860bac05b ("locking/mutex, sched/wait: Fix the mutex_lock_io_nested() define")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/878s6fshii.fsf@nanos.tec.linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3401ecf7fc1b9458a19d42c0e26a228f18ac7dda ]
When kzalloc() returns NULL, no error return code of mpt3sas_base_attach()
is assigned. To fix this bug, r is assigned with -ENOMEM in this case.
Link: https://lore.kernel.org/r/20210308035241.3288-1-baijiaju1990@gmail.com
Fixes: c696f7b83ede ("scsi: mpt3sas: Implement device_remove_in_progress check in IOCTL path")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f69953837ca5d98aa983a138dc0b90a411e9c763 ]
When kzalloc() returns NULL to qedi->global_queues[i], no error return code
of qedi_alloc_global_queues() is assigned. To fix this bug, status is
assigned with -ENOMEM in this case.
Link: https://lore.kernel.org/r/20210308033024.27147-1-baijiaju1990@gmail.com
Fixes: ace7f46ba5fd ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39c0c8553bfb5a3d108aa47f1256076d507605e3 ]
Calling vha->hw->tgt.tgt_ops->free_cmd() from qlt_xmit_response() is wrong
since the command for which a response is sent must remain valid until the
SCSI target core calls .release_cmd(). It has been observed that the
following scenario triggers a kernel crash:
- qlt_xmit_response() calls qlt_check_reserve_free_req()
- qlt_check_reserve_free_req() returns -EAGAIN
- qlt_xmit_response() calls vha->hw->tgt.tgt_ops->free_cmd(cmd)
- transport_handle_queue_full() tries to retransmit the response
Fix this crash by reverting the patch that introduced it.
Link: https://lore.kernel.org/r/20210320232359.941-2-bvanassche@acm.org
Fixes: 0dcec41acb85 ("scsi: qla2xxx: Make sure that aborted commands are freed")
Cc: Quinn Tran <qutran@marvell.com>
Cc: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a958937ff166fc60d1c3a721036f6ff41bfa2821 ]
When a stacked block device inserts a request into another block device
using blk_insert_cloned_request, the request's nr_phys_segments field gets
recalculated by a call to blk_recalc_rq_segments in
blk_cloned_rq_check_limits. But blk_recalc_rq_segments does not know how to
handle multi-segment discards. For disk types which can handle
multi-segment discards like nvme, this results in discard requests which
claim a single segment when it should report several, triggering a warning
in nvme and causing nvme to fail the discard from the invalid state.
WARNING: CPU: 5 PID: 191 at drivers/nvme/host/core.c:700 nvme_setup_discard+0x170/0x1e0 [nvme_core]
...
nvme_setup_cmd+0x217/0x270 [nvme_core]
nvme_loop_queue_rq+0x51/0x1b0 [nvme_loop]
__blk_mq_try_issue_directly+0xe7/0x1b0
blk_mq_request_issue_directly+0x41/0x70
? blk_account_io_start+0x40/0x50
dm_mq_queue_rq+0x200/0x3e0
blk_mq_dispatch_rq_list+0x10a/0x7d0
? __sbitmap_queue_get+0x25/0x90
? elv_rb_del+0x1f/0x30
? deadline_remove_request+0x55/0xb0
? dd_dispatch_request+0x181/0x210
__blk_mq_do_dispatch_sched+0x144/0x290
? bio_attempt_discard_merge+0x134/0x1f0
__blk_mq_sched_dispatch_requests+0x129/0x180
blk_mq_sched_dispatch_requests+0x30/0x60
__blk_mq_run_hw_queue+0x47/0xe0
__blk_mq_delay_run_hw_queue+0x15b/0x170
blk_mq_sched_insert_requests+0x68/0xe0
blk_mq_flush_plug_list+0xf0/0x170
blk_finish_plug+0x36/0x50
xlog_cil_committed+0x19f/0x290 [xfs]
xlog_cil_process_committed+0x57/0x80 [xfs]
xlog_state_do_callback+0x1e0/0x2a0 [xfs]
xlog_ioend_work+0x2f/0x80 [xfs]
process_one_work+0x1b6/0x350
worker_thread+0x53/0x3e0
? process_one_work+0x350/0x350
kthread+0x11b/0x140
? __kthread_bind_mask+0x60/0x60
ret_from_fork+0x22/0x30
This patch fixes blk_recalc_rq_segments to be aware of devices which can
have multi-segment discards. It calculates the correct discard segment
count by counting the number of bio as each discard bio is considered its
own segment.
Fixes: 1e739730c5b9 ("block: optionally merge discontiguous discard bios into a single request")
Signed-off-by: David Jeffery <djeffery@redhat.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Link: https://lore.kernel.org/r/20210211143807.GA115624@redhat
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b410ed2a8572d41c68bd9208555610e4b07d0703 ]
The only requirement of an auxtrace queue is that the buffers are in
time order. That is achieved by making separate queues for separate
perf buffer or AUX area buffer mmaps.
That generally means a separate queue per cpu for per-cpu contexts, and
a separate queue per thread for per-task contexts.
When buffers are added to a queue, perf checks that the buffer cpu and
thread id (tid) match the queue cpu and thread id.
However, generally, that need not be true, and perf will queue buffers
correctly anyway, so the check is not needed.
In addition, the check gets erroneously hit when using sample mode to
trace multiple threads.
Consequently, fix that case by removing the check.
Fixes: e502789302a6 ("perf auxtrace: Add helpers for queuing AUX area tracing data")
Reported-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lore.kernel.org/lkml/20210308151143.18338-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb50aaf960e3bedfef79063411ffd670da94b84b ]
The decrementation of acpi_device_bus_id->instance_no
in acpi_device_del() is incorrect, because it may cause
a duplicate instance number to be allocated next time
a device with the same acpi_device_bus_id is added.
Replace above mentioned approach by using IDA framework.
While at it, define the instance range to be [0, 4096).
Fixes: e49bd2dd5a50 ("ACPI: use PNPID:instance_no as bus_id of ACPI device")
Fixes: ca9dc8d42b30 ("ACPI / scan: Fix acpi_bus_id_list bookkeeping")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1013ff7a5472db637c56bb6237f8343398c03a7 ]
The upfront allocation of new_bus_id is done to avoid allocating
memory under acpi_device_lock, but it doesn't really help,
because (1) it leads to many unnecessary memory allocations for
_ADR devices, (2) kstrdup_const() is run under that lock anyway and
(3) it complicates the code.
Rearrange acpi_device_add() to allocate memory for a new struct
acpi_device_bus_id instance only when necessary, eliminate a redundant
local variable from it and reduce the number of labels in there.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abe7034b9a8d57737e80cc16d60ed3666990bdbf ]
This reverts commit 443d6e86f821a165fae3fc3fc13086d27ac140b1.
This (and the following) patch basically re-implemented the RCU
mechanisms of patch 784544739a25. That patch was replaced because of the
performance problems that it created when replacing tables. Now, we have
the same issue: the call to synchronize_rcu() makes replacing tables
slower by as much as an order of magnitude.
Revert these patches and fix the issue in a different way.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 175e476b8cdf2a4de7432583b49c871345e4f8a1 ]
When a new table value was assigned, it was followed by a write memory
barrier. This ensured that all writes before this point would complete
before any writes after this point. However, to determine whether the
rules are unused, the sequence counter is read. To ensure that all
writes have been done before these reads, a full memory barrier is
needed, not just a write memory barrier. The same argument applies when
incrementing the counter, before the rules are read.
Changing to using smp_mb() instead of smp_wmb() fixes the kernel panic
reported in cc00bcaa5899 (which is still present), while still
maintaining the same speed of replacing tables.
The smb_mb() barriers potentially slow the packet path, however testing
has shown no measurable change in performance on a 4-core MIPS64
platform.
Fixes: 7f5c6d4f665b ("netfilter: get rid of atomic ops in fast path")
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3d40f237480abf3268956daf18cdc56edd32834 ]
This reverts commit cc00bcaa589914096edef7fb87ca5cee4a166b5c.
This (and the preceding) patch basically re-implemented the RCU
mechanisms of patch 784544739a25. That patch was replaced because of the
performance problems that it created when replacing tables. Now, we have
the same issue: the call to synchronize_rcu() makes replacing tables
slower by as much as an order of magnitude.
Prior to using RCU a script calling "iptables" approx. 200 times was
taking 1.16s. With RCU this increased to 11.59s.
Revert these patches and fix the issue in a different way.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05a68ce5fa51a83c360381630f823545c5757aa2 ]
For kuprobe and tracepoint bpf programs, kernel calls
trace_call_bpf() which calls BPF_PROG_RUN_ARRAY_CHECK()
to run the program array. Currently, BPF_PROG_RUN_ARRAY_CHECK()
also calls bpf_cgroup_storage_set() to set percpu
cgroup local storage with NULL value. This is
due to Commit 394e40a29788 ("bpf: extend bpf_prog_array to store
pointers to the cgroup storage") which modified
__BPF_PROG_RUN_ARRAY() to call bpf_cgroup_storage_set()
and this macro is also used by BPF_PROG_RUN_ARRAY_CHECK().
kuprobe and tracepoint programs are not allowed to call
bpf_get_local_storage() helper hence does not
access percpu cgroup local storage. Let us
change BPF_PROG_RUN_ARRAY_CHECK() not to
modify percpu cgroup local storage.
The issue is observed when I tried to debug [1] where
percpu data is overwritten due to
preempt_disable -> migration_disable
change. This patch does not completely fix the above issue,
which will be addressed separately, e.g., multiple cgroup
prog runs may preempt each other. But it does fix
any potential issue caused by tracing program
overwriting percpu cgroup storage:
- in a busy system, a tracing program is to run between
bpf_cgroup_storage_set() and the cgroup prog run.
- a kprobe program is triggered by a helper in cgroup prog
before bpf_get_local_storage() is called.
[1] https://lore.kernel.org/bpf/CAKH8qBuXCfUz=w8L+Fj74OaUpbosO29niYwTki7e3Ag044_aww@mail.gmail.com/T
Fixes: 394e40a29788 ("bpf: extend bpf_prog_array to store pointers to the cgroup storage")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Roman Gushchin <guro@fb.com>
Link: https://lore.kernel.org/bpf/20210309185028.3763817-1-yhs@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3408be145a5d6418ff955fe5badde652be90e700 ]
Not setting the ipv6 bit while destroying ipv6 listening servers may
result in potential fatal adapter errors due to lookup engine memory hash
errors. Therefore always set ipv6 field while destroying ipv6 listening
servers.
Fixes: 830662f6f032 ("RDMA/cxgb4: Add support for active and passive open connection with IPv6 address")
Link: https://lore.kernel.org/r/20210324190453.8171-1-bharat@chelsio.com
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb9d62b27ab1e07d625591549c314b7d406d21df ]
The debugfs directory '/sys/kernel/debug/energy_model' is needed before
the Energy Model registration can happen. With the recent change in
debugfs subsystem it's not allowed to create this directory at early
stage (core_initcall). Thus creating this directory would fail.
Postpone the creation of the EM debug dir to later stage: fs_initcall.
It should be safe since all clients: CPUFreq drivers, Devfreq drivers
will be initialized in later stages.
The custom debug log below prints the time of creation the EM debug dir
at fs_initcall and successful registration of EMs at later stages.
[ 1.505717] energy_model: creating rootdir
[ 3.698307] cpu cpu0: EM: created perf domain
[ 3.709022] cpu cpu1: EM: created perf domain
Fixes: 56348560d495 ("debugfs: do not attempt to create a new file before the filesystem is initalized")
Reported-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5244f5e2d801259af877ee759e8c22364c607072 ]
Because the PM-runtime status of the device is not updated in
__rpm_callback(), attempts to suspend the suppliers of the given
device triggered by the rpm_put_suppliers() call in there may
cause a supplier to be suspended completely before the status of
the consumer is updated to RPM_SUSPENDED, which is confusing.
To avoid that (1) modify __rpm_callback() to only decrease the
PM-runtime usage counter of each supplier and (2) make rpm_suspend()
try to suspend the suppliers after changing the consumer's status to
RPM_SUSPENDED, in analogy with the device's parent.
Link: https://lore.kernel.org/linux-pm/CAPDyKFqm06KDw_p8WXsM4dijDbho4bb6T4k50UqqvR1_COsp8g@mail.gmail.com/
Fixes: 21d5c57b3726 ("PM / runtime: Use device links")
Reported-by: elaine.zhang <zhangqing@rock-chips.com>
Diagnosed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 141f8202cfa4192c3af79b6cbd68e7760bb01b5a ]
The ppos points to a position in the old kernel memory (and in case of
arm64 in the crash kernel since elfcorehdr is passed as a segment). The
function should update the ppos by the amount that was read. This bug is
not exposed by accident, but other platforms update this value properly.
So, fix it in ARM64 version of elfcorehdr_read() as well.
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Fixes: e62aaeac426a ("arm64: kdump: provide /proc/vmcore file")
Reviewed-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Link: https://lore.kernel.org/r/20210319205054.743368-1-pasha.tatashin@soleen.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 901ee1d750f29a335423eeb9463c3ca461ca18c2 ]
The vmlinux.h generated from BTF is invalid when building
drivers/phy/ti/phy-gmii-sel.c with clang:
vmlinux.h:61702:27: error: array type has incomplete element type ‘struct reg_field’
61702 | const struct reg_field (*regfields)[3];
| ^~~~~~~~~
bpftool generates a forward declaration for this struct regfield, which
compilers aren't happy about. Here's a simplified reproducer:
struct inner {
int val;
};
struct outer {
struct inner (*ptr_to_array)[2];
} A;
After build with clang -> bpftool btf dump c -> clang/gcc:
./def-clang.h:11:23: error: array has incomplete element type 'struct inner'
struct inner (*ptr_to_array)[2];
Member ptr_to_array of struct outer is a pointer to an array of struct
inner. In the DWARF generated by clang, struct outer appears before
struct inner, so when converting BTF of struct outer into C, bpftool
issues a forward declaration to struct inner. With GCC the DWARF info is
reversed so struct inner gets fully defined.
That forward declaration is not sufficient when compilers handle an
array of the struct, even when it's only used through a pointer. Note
that we can trigger the same issue with an intermediate typedef:
struct inner {
int val;
};
typedef struct inner inner2_t[2];
struct outer {
inner2_t *ptr_to_array;
} A;
Becomes:
struct inner;
typedef struct inner inner2_t[2];
And causes:
./def-clang.h:10:30: error: array has incomplete element type 'struct inner'
typedef struct inner inner2_t[2];
To fix this, clear through_ptr whenever we encounter an intermediate
array, to make the inner struct part of a strong link and force full
declaration.
Fixes: 351131b51c7a ("libbpf: add btf_dump API for BTF-to-C conversion")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210319112554.794552-2-jean-philippe@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5aa3c334a449bab24519c4967f5ac2b3304c8dcf ]
The ECN bit defines ECT(1) = 1, ECT(0) = 2. So inner 0x02 + outer 0x01
should be inner ECT(0) + outer ECT(1). Based on the description of
__INET_ECN_decapsulate, the final decapsulate value should be
ECT(1). So fix the test expect value to 0x01.
Before the fix:
TEST: VXLAN: ECN decap: 01/02->0x02 [FAIL]
Expected to capture 10 packets, got 0.
After the fix:
TEST: VXLAN: ECN decap: 01/02->0x01 [ OK ]
Fixes: a0b61f3d8ebf ("selftests: forwarding: vxlan_bridge_1d: Add an ECN decap test")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 014dfa26ce1c647af09bf506285ef67e0e3f0a6b ]
MTU cannot be changed on dwmac-sun8i. (ip link set eth0 mtu xxx returning EINVAL)
This is due to tx_fifo_size being 0, since this value is used to compute valid
MTU range.
Like dwmac-sunxi (with commit 806fd188ce2a ("net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes"))
dwmac-sun8i need to have tx and rx fifo sizes set.
I have used values from datasheets.
After this patch, setting a non-default MTU (like 1000) value works and network is still useable.
Tested-on: sun8i-h3-orangepi-pc
Tested-on: sun8i-r40-bananapi-m2-ultra
Tested-on: sun50i-a64-bananapi-m64
Tested-on: sun50i-h5-nanopi-neo-plus2
Tested-on: sun50i-h6-pine-h64
Fixes: 9f93ac8d408 ("net-next: stmmac: Add dwmac-sun8i")
Reported-by: Belisko Marek <marek.belisko@gmail.com>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f91a50d8b51b5c8ef1cfb08115a005bba4250507 ]
If the USB host controller is EHCI, the throughput is reduced from
300Mb/s to 60Mb/s, when the rx buffer size is modified from 16K to
32K.
According to the EHCI spec, the maximum size of the qTD is 20K.
Therefore, when the driver uses more than 20K buffer, the latency
time of EHCI would be increased. And, it let the RTL8153A get worse
throughput.
However, the driver uses alloc_pages() for rx buffer, so I limit
the rx buffer to 16K rather than 20K.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205923
Fixes: ec5791c202ac ("r8152: separate the rx buffer size")
Reported-by: Robert Davies <robdavies1977@gmail.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c79a707072fe3fea0e3c92edee6ca85c1e53c29f ]
Set the disconnected flag before releasing the data interface in case
netdev registration fails to avoid having the disconnect callback try to
deregister the never registered netdev (and trigger a WARN_ON()).
Fixes: 87cf65601e17 ("USB host CDC Phonet network interface driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64451b98306bf1334a62bcd020ec92bdb4cb68db ]
unmapping npc counter works in a way by traversing all mcam
entries to find which mcam rule is associated with counter.
But loop cursor variable 'entry' is not incremented before
checking next mcam entry which resulting in infinite loop.
This in turn hogs the kworker thread forever and no other
mbox message is processed by AF driver after that.
Fix this by updating entry value before checking next
mcam entry.
Fixes: a958dd59f9ce ("octeontx2-af: Map or unmap NPC MCAM entry and counter")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae2619dd4fccdad9876aa5f900bd85484179c50f ]
Current devlink code try to free already freed irqs as the
irq_allocate flag is not cleared after free leading to kernel
crash while removing rvu driver. The patch fixes the irq free
sequence and clears the irq_allocate flag on free.
Fixes: 7304ac4567bc ("octeontx2-af: Add mailbox IRQ and msg handlers")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58bfd95b554f1a23d01228672f86bb489bdbf4ba ]
Otherwise, there exists a small window between the opening and closing
of the socket fd where it may leak into processes launched by some other
thread.
Fixes: 949abbe88436 ("libbpf: add function to setup XDP")
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20210317115857.6536-1-memxor@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8ce0275e45ec809a33f98fc080fe7921b720dfb ]
pre_tun_rule flows does not follow the usual add-flow path, instead
they are used to update the pre_tun table on the firmware. This means
that if the mask-id gets allocated here the firmware will never see the
"NFP_FL_META_FLAG_MANAGE_MASK" flag for the specific mask id, which
triggers the allocation on the firmware side. This leads to the firmware
mask being corrupted and causing all sorts of strange behaviour.
Fixes: f12725d98cbe ("nfp: flower: offload pre-tunnel rules")
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1944015fe9c1d9fa5e9eb7ffbbb5ef8954d6753b ]
Coverity reported the strange "if (~...)" condition that's
always true. It suggested that ! was intended instead of ~,
but upon further analysis I'm convinced that what really was
intended was a comparison to 0xff/0xffff (in HT/VHT cases
respectively), since this indicates that all of the rates
are enabled.
Change the comparison accordingly.
I'm guessing this never really mattered because a reset to
not having a rate mask is basically equivalent to having a
mask that enables all rates.
Reported-by: Colin Ian King <colin.king@canonical.com>
Fixes: 2ffbe6d33366 ("mac80211: fix and optimize MCS mask handling")
Fixes: b119ad6e726c ("mac80211: add rate mask logic for vht rates")
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210212112213.36b38078f569.I8546a20c80bc1669058eb453e213630b846e107b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e98d9ee64ee2cc9b1d1a8e26610ec4d0392ebe50 ]
For M_CAN peripherals, m_can_rx_handler() was called with quota = 1,
which caused any error handling to block RX from taking place until
the next time the IRQ handler is called. This had been observed to
cause RX to be blocked indefinitely in some cases.
This is fixed by calling m_can_rx_handler with a sensibly high quota.
Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework")
Link: https://lore.kernel.org/r/20210303144350.4093750-1-torin@maxiluxsystems.com
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0e399f3baf42279f48991554240af8c457535d1 ]
Message loss from RX FIFO 0 is already handled in
m_can_handle_lost_msg(), with netdev output included.
Removing this warning also improves driver performance under heavy
load, where m_can_do_rx_poll() may be called many times before this
interrupt is cleared, causing this message to be output many
times (thanks Mariusz Madej for this report).
Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support")
Link: https://lore.kernel.org/r/20210303103151.3760532-1-torin@maxiluxsystems.com
Reported-by: Mariusz Madej <mariusz.madej@xtrack.com>
Signed-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e2fe01dd6f98da6cae8b07cd5cfa67abc70d97d ]
Currently doing modprobe c_can_pci will make the kernel complain:
Unbalanced pm_runtime_enable!
this is caused by pm_runtime_enable() called before pm is initialized.
This fix is similar to 227619c3ff7c, move those pm_enable/disable code
to c_can_platform.
Fixes: 4cdd34b26826 ("can: c_can: Add runtime PM support to Bosch C_CAN/D_CAN controller")
Link: http://lore.kernel.org/r/20210302025542.987600-1-ztong0001@gmail.com
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0429d6d89f97ebff4f17f13f5b5069c66bde8138 ]
There is a UAF in c_can_pci_remove(). dev is released by
free_c_can_dev() and is used by pci_iounmap(pdev, priv->base) later.
To fix this issue, save the mmio address before releasing dev.
Fixes: 5b92da0443c2 ("c_can_pci: generic module for C_CAN/D_CAN on PCI")
Link: https://lore.kernel.org/r/20210301024512.539039-1-ztong0001@gmail.com
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c6e6bce08f918b64459415f58061d4d6df44994 ]
Under certain circumstances, when switching from Kvaser's linuxcan driver
(kvpciefd) to the SocketCAN driver (kvaser_pciefd), the bus load reporting
is not disabled.
This is flooding the kernel log with prints like:
[3485.574677] kvaser_pciefd 0000:02:00.0: Received unexpected packet type 0x00000009
Always put the controller in the expected state, instead of assuming that
bus load reporting is inactive.
Note: If bus load reporting is enabled when the driver is loaded, you will
still get a number of bus load packages (and printouts), before it is
disabled.
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Link: https://lore.kernel.org/r/20210309091724.31262-1-jimmyassarsson@gmail.com
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47c5e474bc1e1061fb037d13b5000b38967eb070 ]
For cases when flexcan is built-in, bitrate is still not set at
registering. So flexcan_chip_freeze() generates:
[ 1.860000] *** ZERO DIVIDE *** FORMAT=4
[ 1.860000] Current process id is 1
[ 1.860000] BAD KERNEL TRAP: 00000000
[ 1.860000] PC: [<402e70c8>] flexcan_chip_freeze+0x1a/0xa8
To allow chip freeze, using an hardcoded timeout when bitrate is still
not set.
Fixes: ec15e27cc890 ("can: flexcan: enable RX FIFO after FRZ/HALT valid")
Link: https://lore.kernel.org/r/20210315231510.650593-1-angelo@kernel-space.org
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
[mkl: use if instead of ? operator]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59ec7b89ed3e921cd0625a8c83f31a30d485fdf8 ]
Since the peak_usb driver also supports the CAN-USB interfaces
"PCAN-USB X6" and "PCAN-Chip USB" from PEAK-System GmbH, this patch adds
their names to the list of explicitly supported devices.
Fixes: ea8b65b596d7 ("can: usb: Add support of PCAN-Chip USB stamp module")
Fixes: f00b534ded60 ("can: peak: Add support for PCAN-USB X6 USB interface")
Link: https://lore.kernel.org/r/20210309082128.23125-3-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
