IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 4127caee89612a84adedd78c9453089138cd5afe ]
There are mainly two reasons that thp_get_unmapped_area() should be
used for EROFS as other filesystems:
- It's needed to enable PMD mappings as a FSDAX filesystem, see
commit 74d2fad1334d ("thp, dax: add thp_get_unmapped_area for pmd
mappings");
- It's useful together with large folios and
CONFIG_READ_ONLY_THP_FOR_FS which enable THPs for mmapped files
(e.g. shared libraries) even without FSDAX. See commit 1854bc6e2420
("mm/readahead: Align file mappings for non-DAX").
Fixes: 06252e9ce05b ("erofs: dax support for non-tailpacking regular file")
Fixes: ce529cc25b18 ("erofs: enable large folios for iomap mode")
Fixes: e6687b89225e ("erofs: enable large folios for fscache mode")
Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20240306053138.2240206-1-hsiangkao@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 767146637efc528b5e3d31297df115e85a2fd362 ]
UBSAN load reports an exception of BRK#5515 SHIFT_ISSUE:Bitwise shifts
that are out of bounds for their data type.
vmlinux get_bitmap(b=75) + 712
<net/netfilter/nf_conntrack_h323_asn1.c:0>
vmlinux decode_seq(bs=0xFFFFFFD008037000, f=0xFFFFFFD008037018, level=134443100) + 1956
<net/netfilter/nf_conntrack_h323_asn1.c:592>
vmlinux decode_choice(base=0xFFFFFFD0080370F0, level=23843636) + 1216
<net/netfilter/nf_conntrack_h323_asn1.c:814>
vmlinux decode_seq(f=0xFFFFFFD0080371A8, level=134443500) + 812
<net/netfilter/nf_conntrack_h323_asn1.c:576>
vmlinux decode_choice(base=0xFFFFFFD008037280, level=0) + 1216
<net/netfilter/nf_conntrack_h323_asn1.c:814>
vmlinux DecodeRasMessage() + 304
<net/netfilter/nf_conntrack_h323_asn1.c:833>
vmlinux ras_help() + 684
<net/netfilter/nf_conntrack_h323_main.c:1728>
vmlinux nf_confirm() + 188
<net/netfilter/nf_conntrack_proto.c:137>
Due to abnormal data in skb->data, the extension bitmap length
exceeds 32 when decoding ras message then uses the length to make
a shift operation. It will change into negative after several loop.
UBSAN load could detect a negative shift as an undefined behaviour
and reports exception.
So we add the protection to avoid the length exceeding 32. Or else
it will return out of range error and stop decoding.
Fixes: 5e35941d9901 ("[NETFILTER]: Add H.323 conntrack/NAT helper")
Signed-off-by: Lena Wang <lena.wang@mediatek.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99993789966a6eb4f1295193dc543686899892d3 ]
Following is rejected but should be allowed:
table inet t {
ct expectation exp1 {
[..]
l3proto ip
Valid combos are:
table ip t, l3proto ip
table ip6 t, l3proto ip6
table inet t, l3proto ip OR l3proto ip6
Disallow inet pseudeo family, the l3num must be a on-wire protocol known
to conntrack.
Retain NFPROTO_INET case to make it clear its rejected
intentionally rather as oversight.
Fixes: 8059918a1377 ("netfilter: nft_ct: sanitize layer 3 and 4 protocol number in custom expectations")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c055fc00c07be1f0df7375ab0036cebd1106ed38 ]
If connection isn't established yet, get_mr() will fail, trigger connection after
get_mr().
Fixes: 584a8279a44a ("RDS: RDMA: return appropriate error on rdma map failures")
Reported-and-tested-by: syzbot+d4faee732755bba9838e@syzkaller.appspotmail.com
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2487007aa3b9fafbd2cb14068f49791ce1d7ede5 ]
When running an XDP program that is attached to a cpumap entry, we don't
initialise the xdp_rxq_info data structure being used in the xdp_buff
that backs the XDP program invocation. Tobias noticed that this leads to
random values being returned as the xdp_md->rx_queue_index value for XDP
programs running in a cpumap.
This means we're basically returning the contents of the uninitialised
memory, which is bad. Fix this by zero-initialising the rxq data
structure before running the XDP program.
Fixes: 9216477449f3 ("bpf: cpumap: Add the possibility to attach an eBPF program to cpumap")
Reported-by: Tobias Böhm <tobias@aibor.de>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20240305213132.11955-1-toke@redhat.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06e456a05d669ca30b224b8ed962421770c1496c ]
The function ice_bridge_setlink() may encounter a NULL pointer dereference
if nlmsg_find_attr() returns NULL and br_spec is dereferenced subsequently
in nla_for_each_nested(). To address this issue, add a check to ensure that
br_spec is not NULL before proceeding with the nested attribute iteration.
Fixes: b1edc14a3fbf ("ice: Implement ice_bridge_getlink and ice_bridge_setlink")
Signed-off-by: Rand Deeb <rand.sec96@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89d72d4125e94aa3c2140fedd97ce07ba9e37674 ]
Based on the static analyzis of the code it looks like when an entry
from the MAC table was removed, the entry was still used after being
freed. More precise the vid of the mac_entry was used after calling
devm_kfree on the mac_entry.
The fix consists in first using the vid of the mac_entry to delete the
entry from the HW and after that to free it.
Fixes: b37a1bae742f ("net: sparx5: add mactable support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240301080608.3053468-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51270d573a8d9dd5afdc7934de97d66c0e14b5fd ]
I'm updating __assign_str() and will be removing the second parameter. To
make sure that it does not break anything, I make sure that it matches the
__string() field, as that is where the string is actually going to be
saved in. To make sure there's nothing that breaks, I added a WARN_ON() to
make sure that what was used in __string() is the same that is used in
__assign_str().
In doing this change, an error was triggered as __assign_str() now expects
the string passed in to be a char * value. I instead had the following
warning:
include/trace/events/qdisc.h: In function ‘trace_event_raw_event_qdisc_reset’:
include/trace/events/qdisc.h:91:35: error: passing argument 1 of 'strcmp' from incompatible pointer type [-Werror=incompatible-pointer-types]
91 | __assign_str(dev, qdisc_dev(q));
That's because the qdisc_enqueue() and qdisc_reset() pass in qdisc_dev(q)
to __assign_str() and to __string(). But that function returns a pointer
to struct net_device and not a string.
It appears that these events are just saving the pointer as a string and
then reading it as a string as well.
Use qdisc_dev(q)->name to save the device instead.
Fixes: a34dac0b90552 ("net_sched: add tracepoints for qdisc_reset() and qdisc_destroy()")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d562b11c1eac7d73f4c778b4cbe5468f86b1f20d ]
Disable NAPI before shutting down queues that this particular NAPI
contains so that the order of actions in i40e_queue_pair_disable()
mirrors what we do in i40e_queue_pair_enable().
Fixes: 123cecd427b6 ("i40e: added queue pair disable/enable functions")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbf996f52c4e658b3fb4349a869a62fd2d4c3c1c ]
Currently routines that are supposed to toggle state of ring pair do not
take care of associated interrupt with queue vector that these rings
belong to. This causes funky issues such as dead interface due to irq
misconfiguration, as per Pavel's report from Closes: tag.
Add a function responsible for disabling single IRQ in EIMC register and
call this as a very first thing when disabling ring pair during xsk_pool
setup. For enable let's reuse ixgbe_irq_enable_queues(). Besides this,
disable/enable NAPI as first/last thing when dealing with closing or
opening ring pair that xsk_pool is being configured on.
Reported-by: Pavel Vazharov <pavel@x3me.net>
Closes: https://lore.kernel.org/netdev/CAJEV1ijxNyPTwASJER1bcZzS9nMoZJqfR86nu_3jFFVXzZQ4NA@mail.gmail.com/
Fixes: 024aa5800f32 ("ixgbe: added Rx/Tx ring disable/enable functions")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1eecc7ab82c42133b748e1895275942a054a7f67 ]
Current driver has some asymmetry in the runtime PM calls. On lan78xx_open()
it will call usb_autopm_get() and unconditionally usb_autopm_put(). And
on lan78xx_stop() it will call only usb_autopm_put(). So far, it was
working only because this driver do not activate autosuspend by default,
so it was visible only by warning "Runtime PM usage count underflow!".
Since, with current driver, we can't use runtime PM with active link,
execute lan78xx_open()->usb_autopm_put() only in error case. Otherwise,
keep ref counting high as long as interface is open.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b1ba3f9040be5efc4396d86c9752cdc564730be ]
Turning on CONFIG_DMA_API_DEBUG_SG results in the following warning:
DMA-API: mmci-pl18x 48220000.mmc: cacheline tracking EEXIST,
overlapping mappings aren't supported
WARNING: CPU: 1 PID: 51 at kernel/dma/debug.c:568
add_dma_entry+0x234/0x2f4
Modules linked in:
CPU: 1 PID: 51 Comm: kworker/1:2 Not tainted 6.1.28 #1
Hardware name: STMicroelectronics STM32MP257F-EV1 Evaluation Board (DT)
Workqueue: events_freezable mmc_rescan
Call trace:
add_dma_entry+0x234/0x2f4
debug_dma_map_sg+0x198/0x350
__dma_map_sg_attrs+0xa0/0x110
dma_map_sg_attrs+0x10/0x2c
sdmmc_idma_prep_data+0x80/0xc0
mmci_prep_data+0x38/0x84
mmci_start_data+0x108/0x2dc
mmci_request+0xe4/0x190
__mmc_start_request+0x68/0x140
mmc_start_request+0x94/0xc0
mmc_wait_for_req+0x70/0x100
mmc_send_tuning+0x108/0x1ac
sdmmc_execute_tuning+0x14c/0x210
mmc_execute_tuning+0x48/0xec
mmc_sd_init_uhs_card.part.0+0x208/0x464
mmc_sd_init_card+0x318/0x89c
mmc_attach_sd+0xe4/0x180
mmc_rescan+0x244/0x320
DMA API debug brings to light leaking dma-mappings as dma_map_sg and
dma_unmap_sg are not correctly balanced.
If an error occurs in mmci_cmd_irq function, only mmci_dma_error
function is called and as this API is not managed on stm32 variant,
dma_unmap_sg is never called in this error path.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Fixes: 46b723dd867d ("mmc: mmci: add stm32 sdmmc variant")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240207143951.938144-1-christophe.kerello@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 970dc9c11a17994ab878016b536612ab00d1441d ]
In SDIO mode, the sg list for requests can be unaligned with what the
STM32 SDMMC internal DMA can support. In that case, instead of failing,
use a temporary bounce buffer to copy from/to the sg list.
This buffer is limited to 1MB. But for that we need to also limit
max_req_size to 1MB. It has not shown any throughput penalties for
SD-cards or eMMC.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Link: https://lore.kernel.org/r/20220328145114.334577-1-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Stable-dep-of: 6b1ba3f9040b ("mmc: mmci: stm32: fix DMA API overlapping mappings warning")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 10048689def7e40a4405acda16fdc6477d4ecc5c upstream.
when MPTCP server accepts an incoming connection, it clones its listener
socket. However, the pointer to 'inet_opt' for the new socket has the same
value as the original one: as a consequence, on program exit it's possible
to observe the following splat:
BUG: KASAN: double-free in inet_sock_destruct+0x54f/0x8b0
Free of addr ffff888485950880 by task swapper/25/0
CPU: 25 PID: 0 Comm: swapper/25 Kdump: loaded Not tainted 6.8.0-rc1+ #609
Hardware name: Supermicro SYS-6027R-72RF/X9DRH-7TF/7F/iTF/iF, BIOS 3.0 07/26/2013
Call Trace:
<IRQ>
dump_stack_lvl+0x32/0x50
print_report+0xca/0x620
kasan_report_invalid_free+0x64/0x90
__kasan_slab_free+0x1aa/0x1f0
kfree+0xed/0x2e0
inet_sock_destruct+0x54f/0x8b0
__sk_destruct+0x48/0x5b0
rcu_do_batch+0x34e/0xd90
rcu_core+0x559/0xac0
__do_softirq+0x183/0x5a4
irq_exit_rcu+0x12d/0x170
sysvec_apic_timer_interrupt+0x6b/0x80
</IRQ>
<TASK>
asm_sysvec_apic_timer_interrupt+0x16/0x20
RIP: 0010:cpuidle_enter_state+0x175/0x300
Code: 30 00 0f 84 1f 01 00 00 83 e8 01 83 f8 ff 75 e5 48 83 c4 18 44 89 e8 5b 5d 41 5c 41 5d 41 5e 41 5f c3 cc cc cc cc fb 45 85 ed <0f> 89 60 ff ff ff 48 c1 e5 06 48 c7 43 18 00 00 00 00 48 83 44 2b
RSP: 0018:ffff888481cf7d90 EFLAGS: 00000202
RAX: 0000000000000000 RBX: ffff88887facddc8 RCX: 0000000000000000
RDX: 1ffff1110ff588b1 RSI: 0000000000000019 RDI: ffff88887fac4588
RBP: 0000000000000004 R08: 0000000000000002 R09: 0000000000043080
R10: 0009b02ea273363f R11: ffff88887fabf42b R12: ffffffff932592e0
R13: 0000000000000004 R14: 0000000000000000 R15: 00000022c880ec80
cpuidle_enter+0x4a/0xa0
do_idle+0x310/0x410
cpu_startup_entry+0x51/0x60
start_secondary+0x211/0x270
secondary_startup_64_no_verify+0x184/0x18b
</TASK>
Allocated by task 6853:
kasan_save_stack+0x1c/0x40
kasan_save_track+0x10/0x30
__kasan_kmalloc+0xa6/0xb0
__kmalloc+0x1eb/0x450
cipso_v4_sock_setattr+0x96/0x360
netlbl_sock_setattr+0x132/0x1f0
selinux_netlbl_socket_post_create+0x6c/0x110
selinux_socket_post_create+0x37b/0x7f0
security_socket_post_create+0x63/0xb0
__sock_create+0x305/0x450
__sys_socket_create.part.23+0xbd/0x130
__sys_socket+0x37/0xb0
__x64_sys_socket+0x6f/0xb0
do_syscall_64+0x83/0x160
entry_SYSCALL_64_after_hwframe+0x6e/0x76
Freed by task 6858:
kasan_save_stack+0x1c/0x40
kasan_save_track+0x10/0x30
kasan_save_free_info+0x3b/0x60
__kasan_slab_free+0x12c/0x1f0
kfree+0xed/0x2e0
inet_sock_destruct+0x54f/0x8b0
__sk_destruct+0x48/0x5b0
subflow_ulp_release+0x1f0/0x250
tcp_cleanup_ulp+0x6e/0x110
tcp_v4_destroy_sock+0x5a/0x3a0
inet_csk_destroy_sock+0x135/0x390
tcp_fin+0x416/0x5c0
tcp_data_queue+0x1bc8/0x4310
tcp_rcv_state_process+0x15a3/0x47b0
tcp_v4_do_rcv+0x2c1/0x990
tcp_v4_rcv+0x41fb/0x5ed0
ip_protocol_deliver_rcu+0x6d/0x9f0
ip_local_deliver_finish+0x278/0x360
ip_local_deliver+0x182/0x2c0
ip_rcv+0xb5/0x1c0
__netif_receive_skb_one_core+0x16e/0x1b0
process_backlog+0x1e3/0x650
__napi_poll+0xa6/0x500
net_rx_action+0x740/0xbb0
__do_softirq+0x183/0x5a4
The buggy address belongs to the object at ffff888485950880
which belongs to the cache kmalloc-64 of size 64
The buggy address is located 0 bytes inside of
64-byte region [ffff888485950880, ffff8884859508c0)
The buggy address belongs to the physical page:
page:0000000056d1e95e refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff888485950700 pfn:0x485950
flags: 0x57ffffc0000800(slab|node=1|zone=2|lastcpupid=0x1fffff)
page_type: 0xffffffff()
raw: 0057ffffc0000800 ffff88810004c640 ffffea00121b8ac0 dead000000000006
raw: ffff888485950700 0000000000200019 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888485950780: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
ffff888485950800: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffff888485950880: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
^
ffff888485950900: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
ffff888485950980: 00 00 00 00 00 01 fc fc fc fc fc fc fc fc fc fc
Something similar (a refcount underflow) happens with CALIPSO/IPv6. Fix
this by duplicating IP / IPv6 options after clone, so that
ip{,6}_sock_destruct() doesn't end up freeing the same memory area twice.
Fixes: cf7da0d66cc1 ("mptcp: Create SUBFLOW socket for incoming connections")
Cc: stable@vger.kernel.org
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-8-162e87e48497@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a069a90554168ac4cc81af65f000557d2a8a0745 upstream.
This reverts commit 284b4d93daee56dff3e10029ddf2e03227f50dbf.
When using TLS device offload and coming from tls_device_reencrypt()
flow, -EBADMSG error in tls_do_decryption() should not be counted
towards the TLSTlsDecryptError counter.
Move the counter increase back to the decrypt_internal() call site in
decrypt_skb_update().
This also fixes an issue where:
if (n_sgin < 1)
return -EBADMSG;
Errors in decrypt_internal() were not counted after the cited patch.
Fixes: 284b4d93daee ("tls: rx: move counting TlsDecryptErrors for sync")
Cc: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c706b2b5ed74d30436b85cbd8e63e969f6b5873a upstream.
When NIC takes care of crypto (or the record has already
been decrypted) we forget to update darg->async. ->async
is supposed to mean whether record is async capable on
input and whether record has been queued for async crypto
on output.
Reported-by: Gal Pressman <gal@nvidia.com>
Fixes: 3547a1f9d988 ("tls: rx: use async as an in-out argument")
Tested-by: Gal Pressman <gal@nvidia.com>
Link: https://lore.kernel.org/r/20220425233309.344858-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dab4e1f06cabb6834de14264394ccab197007302 upstream.
Extend the bpf_fib_lookup() helper by making it to return the source
IPv4/IPv6 address if the BPF_FIB_LOOKUP_SRC flag is set.
For example, the following snippet can be used to derive the desired
source IP address:
struct bpf_fib_lookup p = { .ipv4_dst = ip4->daddr };
ret = bpf_skb_fib_lookup(skb, p, sizeof(p),
BPF_FIB_LOOKUP_SRC | BPF_FIB_LOOKUP_SKIP_NEIGH);
if (ret != BPF_FIB_LKUP_RET_SUCCESS)
return TC_ACT_SHOT;
/* the p.ipv4_src now contains the source address */
The inability to derive the proper source address may cause malfunctions
in BPF-based dataplanes for hosts containing netdevs with more than one
routable IP address or for multi-homed hosts.
For example, Cilium implements packet masquerading in BPF. If an
egressing netdev to which the Cilium's BPF prog is attached has
multiple IP addresses, then only one [hardcoded] IP address can be used for
masquerading. This breaks connectivity if any other IP address should have
been selected instead, for example, when a public and private addresses
are attached to the same egress interface.
The change was tested with Cilium [1].
Nikolay Aleksandrov helped to figure out the IPv6 addr selection.
[1]: https://github.com/cilium/cilium/pull/28283
Signed-off-by: Martynas Pumputis <m@lambda.lt>
Link: https://lore.kernel.org/r/20231007081415.33502-2-m@lambda.lt
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ad77e72caae22a1ddcfd0c03f2884929e93b7a4 upstream.
Add ability to specify routing table ID to the `bpf_fib_lookup` BPF
helper.
A new field `tbid` is added to `struct bpf_fib_lookup` used as
parameters to the `bpf_fib_lookup` BPF helper.
When the helper is called with the `BPF_FIB_LOOKUP_DIRECT` and
`BPF_FIB_LOOKUP_TBID` flags the `tbid` field in `struct bpf_fib_lookup`
will be used as the table ID for the fib lookup.
If the `tbid` does not exist the fib lookup will fail with
`BPF_FIB_LKUP_RET_NOT_FWDED`.
The `tbid` field becomes a union over the vlan related output fields
in `struct bpf_fib_lookup` and will be zeroed immediately after usage.
This functionality is useful in containerized environments.
For instance, if a CNI wants to dictate the next-hop for traffic leaving
a container it can create a container-specific routing table and perform
a fib lookup against this table in a "host-net-namespace-side" TC program.
This functionality also allows `ip rule` like functionality at the TC
layer, allowing an eBPF program to pick a routing table based on some
aspect of the sk_buff.
As a concrete use case, this feature will be used in Cilium's SRv6 L3VPN
datapath.
When egress traffic leaves a Pod an eBPF program attached by Cilium will
determine which VRF the egress traffic should target, and then perform a
FIB lookup in a specific table representing this VRF's FIB.
Signed-off-by: Louis DeLosSantos <louis.delos.devel@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230505-bpf-add-tbid-fib-lookup-v2-1-0a31c22c748c@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31de4105f00d64570139bc5494a201b0bd57349f upstream.
The bpf_fib_lookup() also looks up the neigh table.
This was done before bpf_redirect_neigh() was added.
In the use case that does not manage the neigh table
and requires bpf_fib_lookup() to lookup a fib to
decide if it needs to redirect or not, the bpf prog can
depend only on using bpf_redirect_neigh() to lookup the
neigh. It also keeps the neigh entries fresh and connected.
This patch adds a bpf_fib_lookup flag, SKIP_NEIGH, to avoid
the double neigh lookup when the bpf prog always call
bpf_redirect_neigh() to do the neigh lookup. The params->smac
output is skipped together when SKIP_NEIGH is set because
bpf_redirect_neigh() will figure out the smac also.
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230217205515.3583372-1-martin.lau@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e3a29b80e9e6df217dd61c670ac42864fa4a0e67 which is
commit 13619170303878e1dae86d9a58b039475c957fcf upstream.
It is reported to cause boot crashes in Android systems, so revert it
from the stable trees for now.
Cc: Rob Clark <robdclark@chromium.org>
Cc: Georgi Djakov <djakov@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 9be2957f014d91088db1eb5dd09d9a03d7184dce which is
commit af42269c3523492d71ebbe11fefae2653e9cdc78 upstream.
It is reported to cause boot crashes in Android systems, so revert it
from the stable trees for now.
Cc: Rob Clark <robdclark@chromium.org>
Cc: Georgi Djakov <djakov@kernel.org>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ec5c54a9d3c4f9c15e647b049fea401ee5258696 ]
Hogs are added *after* ACPI so should be removed *before* in error path.
Fixes: a411e81e61df ("gpiolib: add hogs support for machine code")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 530b1dbd97846b110ea8a94c7cc903eca21786e5 ]
Chip outputs are enabled[1] before actual reset is performed[2] which might
cause pin output value to flip flop if previous pin value was set to 1.
Fix that behavior by making sure chip is fully reset before all outputs are
enabled.
Flip-flop can be noticed when module is removed and inserted again and one of
the pins was changed to 1 before removal. 100 microsecond flipping is
noticeable on oscilloscope (100khz SPI bus).
For a properly reset chip - output is enabled around 100 microseconds (on 100khz
SPI bus) later during probing process hence should be irrelevant behavioral
change.
Fixes: 7ebc194d0fd4 (gpio: 74x164: Introduce 'enable-gpios' property)
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L130 [1]
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L150 [2]
Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit aa82ac51d63328714645c827775d64dbfd9941f3 upstream.
syzbot reported another task hung in __unix_gc(). [0]
The current while loop assumes that all of the left candidates
have oob_skb and calling kfree_skb(oob_skb) releases the remaining
candidates.
However, I missed a case that oob_skb has self-referencing fd and
another fd and the latter sk is placed before the former in the
candidate list. Then, the while loop never proceeds, resulting
the task hung.
__unix_gc() has the same loop just before purging the collected skb,
so we can call kfree_skb(oob_skb) there and let __skb_queue_purge()
release all inflight sockets.
[0]:
Sending NMI from CPU 0 to CPUs 1:
NMI backtrace for cpu 1
CPU: 1 PID: 2784 Comm: kworker/u4:8 Not tainted 6.8.0-rc4-syzkaller-01028-g71b605d32017 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/25/2024
Workqueue: events_unbound __unix_gc
RIP: 0010:__sanitizer_cov_trace_pc+0x0/0x70 kernel/kcov.c:200
Code: 89 fb e8 23 00 00 00 48 8b 3d 84 f5 1a 0c 48 89 de 5b e9 43 26 57 00 0f 1f 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 <f3> 0f 1e fa 48 8b 04 24 65 48 8b 0d 90 52 70 7e 65 8b 15 91 52 70
RSP: 0018:ffffc9000a17fa78 EFLAGS: 00000287
RAX: ffffffff8a0a6108 RBX: ffff88802b6c2640 RCX: ffff88802c0b3b80
RDX: 0000000000000000 RSI: 0000000000000002 RDI: 0000000000000000
RBP: ffffc9000a17fbf0 R08: ffffffff89383f1d R09: 1ffff1100ee5ff84
R10: dffffc0000000000 R11: ffffed100ee5ff85 R12: 1ffff110056d84ee
R13: ffffc9000a17fae0 R14: 0000000000000000 R15: ffffffff8f47b840
FS: 0000000000000000(0000) GS:ffff8880b9500000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffef5687ff8 CR3: 0000000029b34000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<NMI>
</NMI>
<TASK>
__unix_gc+0xe69/0xf40 net/unix/garbage.c:343
process_one_work kernel/workqueue.c:2633 [inline]
process_scheduled_works+0x913/0x1420 kernel/workqueue.c:2706
worker_thread+0xa5f/0x1000 kernel/workqueue.c:2787
kthread+0x2ef/0x390 kernel/kthread.c:388
ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1b/0x30 arch/x86/entry/entry_64.S:242
</TASK>
Reported-and-tested-by: syzbot+ecab4d36f920c3574bf9@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=ecab4d36f920c3574bf9
Fixes: 25236c91b5ab ("af_unix: Fix task hung while purging oob_skb in GC.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit ef4a40953c8076626875ff91c41e210fcee7a6fd which is
commit d89078c37b10f05fa4f4791b71db2572db361b68 upstream.
The commit was applied to make further commits apply cleanly, but the
commit depends on other commits in the same patchset. I.e. the
controlling DSI host would need a change too. Thus one would need to
backport the full patchset changing the DSI hosts and all downstream
DSI device drivers.
Revert the commit and fix up the conflicts with the backported fixes
to the lt8912b driver.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9cd26f640a308ea314ad23532de9a8592cd09d2 upstream.
when inserting not contiguous data in the subflow write queue,
the protocol creates a new skb and prevent the TCP stack from
merging it later with already queued skbs by setting the EOR marker.
Still no push flag is explicitly set at the end of previous GSO
packet, making the aggregation on the receiver side sub-optimal -
and packetdrill self-tests less predictable.
Explicitly mark the end of not contiguous DSS with the push flag.
Fixes: 6d0060f600ad ("mptcp: Write MPTCP DSS headers to outgoing data packets")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-4-162e87e48497@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 584f3894262634596532cf43a5e782e34a0ce374 upstream.
Just the same as userspace PM, a new parameter needs_id is added for
in-kernel PM mptcp_pm_nl_append_new_local_addr() too.
Add a new helper mptcp_pm_has_addr_attr_id() to check whether an address
ID is set from PM or not.
In mptcp_pm_nl_get_local_id(), needs_id is always true, but in
mptcp_pm_nl_add_addr_doit(), pass mptcp_pm_has_addr_attr_id() to
needs_it.
Fixes: efd5a4c04e18 ("mptcp: add the address ID assignment bitmap")
Cc: stable@vger.kernel.org
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59060a47ca50bbdb1d863b73667a1065873ecc06 upstream.
entry->addr.id is u8 with a range from 0 to 255 and MAX_ADDR_ID is 255.
We should drop both false expressions of (entry->addr.id > MAX_ADDR_ID).
We should also remove the obsolete parentheses in the first if branch.
Use U8_MAX for MAX_ADDR_ID and add a comment to show the link to
mptcp_addr_info.id as suggested by Mr. Matthieu Baerts.
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c86fad2cecdc6bf7283ecd298b4d0555bd8b8aa upstream.
Since the commit mentioned below, 'mptcp_join' selftests is using
IPTables to add rules to the Filter table for IPv6.
It is then required to have IP6_NF_FILTER KConfig.
This KConfig is usually enabled by default in many defconfig, but we
recently noticed that some CI were running our selftests without them
enabled.
Fixes: 523514ed0a99 ("selftests: mptcp: add ADD_ADDR IPv6 test cases")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240131-upstream-net-20240131-mptcp-ci-issues-v1-3-4c1c11e571ff@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3645c844902bd4e173d6704fc2a37e8746904d67 upstream.
Since the commit mentioned below, 'mptcp_join' selftests is using
IPTables to add rules to the Filter table.
It is then required to have IP_NF_FILTER KConfig.
This KConfig is usually enabled by default in many defconfig, but we
recently noticed that some CI were running our selftests without them
enabled.
Fixes: 8d014eaa9254 ("selftests: mptcp: add ADD_ADDR timeout test case")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6909dc1c1f4452879278128012da6c76bc186a5 upstream.
The msk socket uses to different timeout to track close related
events and retransmissions. The existing helpers do not indicate
clearly which timer they actually touch, making the related code
quite confusing.
Change the existing helpers name to avoid such confusion. No
functional change intended.
This patch is linked to the next one ("mptcp: fix dangling connection
hang-up"). The two patches are supposed to be backported together.
Cc: stable@vger.kernel.org # v5.11+
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f1a98813b4b686482e5ef3c9d998581cace0ba6 upstream.
On incoming TCP reset, subflow closing could happen before error
propagation. That in turn could cause the socket error being ignored,
and a missing socket state transition, as reported by Daire-Byrne.
Address the issues explicitly checking for subflow socket error at
close time. To avoid code duplication, factor-out of __mptcp_error_report()
a new helper implementing the relevant bits.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/429
Fixes: 15cc10453398 ("mptcp: deliver ssk errors to msk")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5fbeff1ab812b6c473b6924bee8748469462e2c upstream.
This will simplify the next patch ("mptcp: process pending subflow error
on close").
No functional change intended.
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6890cb1ace350b4386c8aee1343dc3b3ddd214da upstream.
MKTME repurposes the high bit of physical address to key id for encryption
key and, even though MAXPHYADDR in CPUID[0x80000008] remains the same,
the valid bits in the MTRR mask register are based on the reduced number
of physical address bits.
detect_tme() in arch/x86/kernel/cpu/intel.c detects TME and subtracts
it from the total usable physical bits, but it is called too late.
Move the call to early_init_intel() so that it is called in setup_arch(),
before MTRRs are setup.
This fixes boot on TDX-enabled systems, which until now only worked with
"disable_mtrr_cleanup". Without the patch, the values written to the
MTRRs mask registers were 52-bit wide (e.g. 0x000fffff_80000800) and
the writes failed; with the patch, the values are 46-bit wide, which
matches the reduced MAXPHYADDR that is shown in /proc/cpuinfo.
Reported-by: Zixi Chen <zixchen@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc:stable@vger.kernel.org
Link: https://lore.kernel.org/all/20240131230902.1867092-3-pbonzini%40redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a93c6cbd5a703d44c414a3c3945a87ce11430ba upstream.
Commit 'e3e56c050ab6 ("soc: qcom: rpmhpd: Make power_on actually enable
the domain")' aimed to make sure that a power-domain that is being
enabled without any particular performance-state requested will at least
turn the rail on, to avoid filling DeviceTree with otherwise unnecessary
required-opps properties.
But in the event that aggregation happens on a disabled power-domain, with
an enabled peer without performance-state, both the local and peer
corner are 0. The peer's enabled_corner is not considered, with the
result that the underlying (shared) resource is disabled.
One case where this can be observed is when the display stack keeps mmcx
enabled (but without a particular performance-state vote) in order to
access registers and sync_state happens in the rpmhpd driver. As mmcx_ao
is flushed the state of the peer (mmcx) is not considered and mmcx_ao
ends up turning off "mmcx.lvl" underneath mmcx. This has been observed
several times, but has been painted over in DeviceTree by adding an
explicit vote for the lowest non-disabled performance-state.
Fixes: e3e56c050ab6 ("soc: qcom: rpmhpd: Make power_on actually enable the domain")
Reported-by: Johan Hovold <johan@kernel.org>
Closes: https://lore.kernel.org/linux-arm-msm/ZdMwZa98L23mu3u6@hovoldconsulting.com/
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240226-rpmhpd-enable-corner-fix-v1-1-68c004cec48c@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e9f25a290ae0016353c9ea13314c95fb3207812 upstream.
Each time SD/mmc phy is initialized, at times, in some of
the attempts, phy fails to completes its initialization
which results into timeout error. Per the HW spec, it is
a pre-requisite to ensure a stable SD clock before a phy
initialization is attempted.
Fixes: 06c8b667ff5b ("mmc: sdhci-xenon: Add support to PHYs of Marvell Xenon SDHC")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Elad Nachman <enachman@marvell.com>
Link: https://lore.kernel.org/r/20240222200930.1277665-1-enachman@marvell.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09e23823ae9a3e2d5d20f2e1efe0d6e48cef9129 upstream.
AC5X spec says PHY init complete bit must be polled until zero.
We see cases in which timeout can take longer than the standard
calculation on AC5X, which is expected following the spec comment above.
According to the spec, we must wait as long as it takes for that bit to
toggle on AC5X.
Cap that with 100 delay loops so we won't get stuck forever.
Fixes: 06c8b667ff5b ("mmc: sdhci-xenon: Add support to PHYs of Marvell Xenon SDHC")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Elad Nachman <enachman@marvell.com>
Link: https://lore.kernel.org/r/20240222191714.1216470-3-enachman@marvell.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff3206d2186d84e4f77e1378ba1d225633f17b9b upstream.
Initializing an eMMC that's connected via a 1-bit bus is current failing,
if the HW (DT) informs that 4-bit bus is supported. In fact this is a
regression, as we were earlier capable of falling back to 1-bit mode, when
switching to 4/8-bit bus failed. Therefore, let's restore the behaviour.
Log for Samsung eMMC 5.1 chip connected via 1bit bus (only D0 pin)
Before patch:
[134509.044225] mmc0: switch to bus width 4 failed
[134509.044509] mmc0: new high speed MMC card at address 0001
[134509.054594] mmcblk0: mmc0:0001 BGUF4R 29.1 GiB
[134509.281602] mmc0: switch to bus width 4 failed
[134509.282638] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.282657] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.284598] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.284602] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.284609] ldm_validate_partition_table(): Disk read failed.
[134509.286495] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.286500] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.288303] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.288308] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.289540] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.289544] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.289553] mmcblk0: unable to read partition table
[134509.289728] mmcblk0boot0: mmc0:0001 BGUF4R 31.9 MiB
[134509.290283] mmcblk0boot1: mmc0:0001 BGUF4R 31.9 MiB
[134509.294577] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[134509.295835] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.295841] Buffer I/O error on dev mmcblk0, logical block 0, async page read
After patch:
[134551.089613] mmc0: switch to bus width 4 failed
[134551.090377] mmc0: new high speed MMC card at address 0001
[134551.102271] mmcblk0: mmc0:0001 BGUF4R 29.1 GiB
[134551.113365] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21
[134551.114262] mmcblk0boot0: mmc0:0001 BGUF4R 31.9 MiB
[134551.114925] mmcblk0boot1: mmc0:0001 BGUF4R 31.9 MiB
Fixes: 577fb13199b1 ("mmc: rework selection of bus speed mode")
Cc: stable@vger.kernel.org
Signed-off-by: Ivan Semenov <ivan@semenov.dev>
Link: https://lore.kernel.org/r/20240206172845.34316-1-ivan@semenov.dev
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87a39071e0b639f45e05d296cc0538eef44ec0bd upstream.
Initialize the qDMA irqs after the registers are configured so that
interrupts that may have been pending from a primary kernel don't get
processed by the irq handler before it is ready to and cause panic with
the following trace:
Call trace:
fsl_qdma_queue_handler+0xf8/0x3e8
__handle_irq_event_percpu+0x78/0x2b0
handle_irq_event_percpu+0x1c/0x68
handle_irq_event+0x44/0x78
handle_fasteoi_irq+0xc8/0x178
generic_handle_irq+0x24/0x38
__handle_domain_irq+0x90/0x100
gic_handle_irq+0x5c/0xb8
el1_irq+0xb8/0x180
_raw_spin_unlock_irqrestore+0x14/0x40
__setup_irq+0x4bc/0x798
request_threaded_irq+0xd8/0x190
devm_request_threaded_irq+0x74/0xe8
fsl_qdma_probe+0x4d4/0xca8
platform_drv_probe+0x50/0xa0
really_probe+0xe0/0x3f8
driver_probe_device+0x64/0x130
device_driver_attach+0x6c/0x78
__driver_attach+0xbc/0x158
bus_for_each_dev+0x5c/0x98
driver_attach+0x20/0x28
bus_add_driver+0x158/0x220
driver_register+0x60/0x110
__platform_driver_register+0x44/0x50
fsl_qdma_driver_init+0x18/0x20
do_one_initcall+0x48/0x258
kernel_init_freeable+0x1a4/0x23c
kernel_init+0x10/0xf8
ret_from_fork+0x10/0x18
Cc: stable@vger.kernel.org
Fixes: b092529e0aa0 ("dmaengine: fsl-qdma: Add qDMA controller driver for Layerscape SoCs")
Signed-off-by: Curtis Klein <curtis.klein@hpe.com>
Signed-off-by: Yi Zhao <yi.zhao@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240201220406.440145-1-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df2515a17914ecfc2a0594509deaf7fcb8d191ac upstream.
The PTDMA driver sets DMA masks in two different places for the same
device inconsistently. First call is in pt_pci_probe(), where it uses
48bit mask. The second call is in pt_dmaengine_register(), where it
uses a 64bit mask. Using 64bit dma mask causes IO_PAGE_FAULT errors
on DMA transfers between main memory and other devices.
Without the extra call it works fine. Additionally the second call
doesn't check the return value so it can silently fail.
Remove the superfluous dma_set_mask() call and only use 48bit mask.
Cc: stable@vger.kernel.org
Fixes: b0b4a6b10577 ("dmaengine: ptdma: register PTDMA controller as a DMA resource")
Reviewed-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Tadeusz Struk <tstruk@gigaio.com>
Link: https://lore.kernel.org/r/20240222163053.13842-1-tstruk@gigaio.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d739bccf261dd93ec1babf82f5c5d71dd4caa3e upstream.
There is chip (ls1028a) errata:
The SoC may hang on 16 byte unaligned read transactions by QDMA.
Unaligned read transactions initiated by QDMA may stall in the NOC
(Network On-Chip), causing a deadlock condition. Stalled transactions will
trigger completion timeouts in PCIe controller.
Workaround:
Enable prefetch by setting the source descriptor prefetchable bit
( SD[PF] = 1 ).
Implement this workaround.
Cc: stable@vger.kernel.org
Fixes: b092529e0aa0 ("dmaengine: fsl-qdma: Add qDMA controller driver for Layerscape SoCs")
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240201215007.439503-1-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9845664b9ee47ce7ee7ea93caf47d39a9d4552c4 upstream.
There's a syzbot report that device name buffers passed to device
replace are not properly checked for string termination which could lead
to a read out of bounds in getname_kernel().
Add a helper that validates both source and target device name buffers.
For devid as the source initialize the buffer to empty string in case
something tries to read it later.
This was originally analyzed and fixed in a different way by Edward Adam
Davis (see links).
Link: https://lore.kernel.org/linux-btrfs/000000000000d1a1d1060cc9c5e7@google.com/
Link: https://lore.kernel.org/linux-btrfs/tencent_44CA0665C9836EF9EEC80CB9E7E206DF5206@qq.com/
CC: stable@vger.kernel.org # 4.19+
CC: Edward Adam Davis <eadavis@qq.com>
Reported-and-tested-by: syzbot+33f23b49ac24f986c9e8@syzkaller.appspotmail.com
Reviewed-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f78c1375339a291cba492a70eaf12ec501d28a8e upstream.
It's currently possible to change the mesh ID when the
interface isn't yet in mesh mode, at the same time as
changing it into mesh mode. This leads to an overwrite
of data in the wdev->u union for the interface type it
currently has, causing cfg80211_change_iface() to do
wrong things when switching.
We could probably allow setting an interface to mesh
while setting the mesh ID at the same time by doing a
different order of operations here, but realistically
there's no userspace that's going to do this, so just
disallow changes in iftype when setting mesh ID.
Cc: stable@vger.kernel.org
Fixes: 29cbe68c516a ("cfg80211/mac80211: add mesh join/leave commands")
Reported-by: syzbot+dd4779978217b1973180@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gao Xiang
Lena Wang
Florian Westphal
Edward Adam Davis
Toke Høiland-Jørgensen
Eric Dumazet
Rand Deeb
Horatiu Vultur
Steven Rostedt (Google)
Maciej Fijalkowski
Oleksij Rempel
Christophe Kerello
Yann Gautier
Greg Kroah-Hartman
Davide Caratti
Gal Pressman
Jakub Kicinski
Martynas Pumputis
Louis DeLosSantos
Martin KaFai Lau
Bartosz Golaszewski
Andy Shevchenko
Arturas Moskvinas
Kuniyuki Iwashima
Max Krummenacher
Oscar Salvador
Baokun Li
Paolo Abeni
Geliang Tang
Jean Sacren
Matthieu Baerts (NGI0)
Paolo Bonzini
Bjorn Andersson
Elad Nachman
Ivan Semenov
Curtis Klein
Tadeusz Struk
Peng Ma
David Sterba
Johannes Berg