IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit f22725c95e ]
Corentin Labbe reports that the SSI 1328 does not work when allowing
the PHY to operate at gigabit speeds, but does work with the generic
PHY driver.
This appears to be because m88e1118_config_init() writes a fixed value
to the MSCR register, claiming that this is to enable 1G speeds.
However, this always sets bits 4 and 5, enabling RGMII transmit and
receive delays. The suspicion is that the original board this was
added for required the delays to make 1G speeds work.
Add the necessary configuration for RGMII delays for the 88E1118 to
bring this into line with the requirements for RGMII support, and thus
make the SSI 1328 work.
Corentin Labbe has tested this on gemini-ssi1328 and gemini-ns2502.
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d43e427174 ]
Locally generated packets ingress the device through its CPU port. When
the CPU port is congested and there are not enough credits in its
headroom buffer, packets can be dropped.
While this might be acceptable for data packets that traverse the
network, configuration packets exchanged between the host and the device
(EMADs) should not be subjected to this flow control.
The "sdq_lp" bit in the SDQ (Send Descriptor Queue) context allows the
host to instruct the device to treat packets sent on this queue as
"local processing" and always process them, regardless of the state of
the CPU port's headroom.
Add the definition of this bit and set it for the dedicated SDQ reserved
for the transmission of EMAD packets. This makes the "local processing"
bit in the WQE (Work Queue Element) redundant, so clear it.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04be6d337d ]
Some AP can possibly try non-standard VHT rate and mac80211 warns and drops
packets, and leads low TCP throughput.
Rate marked as a VHT rate but data is invalid: MCS: 10, NSS: 2
WARNING: CPU: 1 PID: 7817 at net/mac80211/rx.c:4856 ieee80211_rx_list+0x223/0x2f0 [mac8021
Since commit c27aa56a72 ("cfg80211: add VHT rate entries for MCS-10 and MCS-11")
has added, mac80211 adds this support as well.
After this patch, throughput is good and iw can get the bitrate:
rx bitrate: 975.1 MBit/s VHT-MCS 10 80MHz short GI VHT-NSS 2
or
rx bitrate: 1083.3 MBit/s VHT-MCS 11 80MHz short GI VHT-NSS 2
Buglink: https://bugzilla.suse.com/show_bug.cgi?id=1192891
Reported-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20220103013623.17052-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f05c09d6b ]
If we're looking for leafs that point to a data extent we want to record
the extent items that point at our bytenr. At this point we have the
reference and we know for a fact that this leaf should have a reference
to our bytenr. However if there's some sort of corruption we may not
find any references to our leaf, and thus could end up with eie == NULL.
Replace this BUG_ON() with an ASSERT() and then return -EUCLEAN for the
mortals.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcba0120ed ]
We search for an extent entry with .offset = -1, which shouldn't be a
thing, but corruption happens. Add an ASSERT() for the developers,
return -EUCLEAN for mortals.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e96c1197ac ]
The EC/ACPI firmware on Lenovo ThinkPads used to report a status
of "Unknown" when the battery is between the charge start and
charge stop thresholds. On Windows, it reports "Not Charging"
so the quirk has been added to also report correctly.
Now the "status" attribute returns "Not Charging" when the
battery on ThinkPads is not physicaly charging.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11c9cc95f8 ]
== Description ==
Setting values of pm attributes through sysfs
should not be allowed in SRIOV mode.
These calls will not be processed by FW anyway,
but error handling on sysfs level should be improved.
== Changes ==
This patch prohibits performing of all set commands
in SRIOV mode on sysfs level.
It offers better error handling as calls that are
not allowed will not be propagated further.
== Test ==
Writing to any sysfs file in passthrough mode will succeed.
Writing to any sysfs file in ONEVF mode will yield error:
"calling process does not have sufficient permission to execute a command".
Signed-off-by: Marina Nikolic <Marina.Nikolic@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11544d77e3 ]
Some boards(like RX550) seem to have garbage in the upper
16 bits of the vram size register. Check for
this and clamp the size properly. Fixes
boards reporting bogus amounts of vram.
after add this patch,the maximum GPU VRAM size is 64GB,
otherwise only 64GB vram size will be used.
Signed-off-by: Zongmin Zhou<zhouzongmin@kylinos.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d4e0b3abb ]
ACPICA commit 3dd7e1f3996456ef81bfe14cba29860e8d42949e
According to ACPI 6.4, Section 16.2, the CPU cache flushing is
required on entering to S1, S2, and S3, but the ACPICA code
flushes the CPU cache regardless of the sleep state.
Blind cache flush on entering S5 causes problems for TDX.
Flushing happens with WBINVD that is not supported in the TDX
environment.
TDX only supports S5 and adjusting ACPICA code to conform to the
spec more strictly fixes the issue.
Link: https://github.com/acpica/acpica/commit/3dd7e1f3
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a3b8655db ]
ACPICA commit 41be6afacfdaec2dba3a5ed368736babc2a7aa5c
With the PCC Opregion in the firmware and we are hitting below kernel crash:
-->8
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
Workqueue: pm pm_runtime_work
pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __memcpy+0x54/0x260
lr : acpi_ex_write_data_to_field+0xb8/0x194
Call trace:
__memcpy+0x54/0x260
acpi_ex_store_object_to_node+0xa4/0x1d4
acpi_ex_store+0x44/0x164
acpi_ex_opcode_1A_1T_1R+0x25c/0x508
acpi_ds_exec_end_op+0x1b4/0x44c
acpi_ps_parse_loop+0x3a8/0x614
acpi_ps_parse_aml+0x90/0x2f4
acpi_ps_execute_method+0x11c/0x19c
acpi_ns_evaluate+0x1ec/0x2b0
acpi_evaluate_object+0x170/0x2b0
acpi_device_set_power+0x118/0x310
acpi_dev_suspend+0xd4/0x180
acpi_subsys_runtime_suspend+0x28/0x38
__rpm_callback+0x74/0x328
rpm_suspend+0x2d8/0x624
pm_runtime_work+0xa4/0xb8
process_one_work+0x194/0x25c
worker_thread+0x260/0x49c
kthread+0x14c/0x30c
ret_from_fork+0x10/0x20
Code: f9000006 f81f80a7 d65f03c0 361000c2 (b9400026)
---[ end trace 24d8a032fa77b68a ]---
The reason for the crash is that the PCC channel index passed via region.address
in acpi_ex_store_object_to_node is interpreted as the channel subtype
incorrectly.
Assuming the PCC op_region support is not used by any other type, let us
remove the subtype check as the AML has no access to the subtype information.
Once we remove it, the kernel crash disappears and correctly complains about
missing PCC Opregion handler.
ACPI Error: No handler for Region [PFRM] ((____ptrval____)) [PCC] (20210730/evregion-130)
ACPI Error: Region PCC (ID=10) has no handler (20210730/exfldio-261)
ACPI Error: Aborting method \_SB.ETH0._PS3 due to previous error (AE_NOT_EXIST) (20210730/psparse-531)
Link: https://github.com/acpica/acpica/commit/41be6afa
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24ea5f90ec ]
ACPICA commit d984f12041392fa4156b52e2f7e5c5e7bc38ad9e
If Operand[0] is a reference of the ACPI_REFCLASS_REFOF class,
acpi_ex_opcode_1A_0T_1R () calls acpi_ns_get_attached_object () to
obtain return_desc which may require additional resolution with
the help of acpi_ex_read_data_from_field (). If the latter fails,
the reference counter of the original return_desc is decremented
which is incorrect, because acpi_ns_get_attached_object () does not
increment the reference counter of the object returned by it.
This issue may lead to premature deletion of the attached object
while it is still attached and a use-after-free and crash in the
host OS. For example, this may happen when on evaluation of ref_of()
a local region field where there is no registered handler for the
given Operation Region.
Fix it by making acpi_ex_opcode_1A_0T_1R () return Status right away
after a acpi_ex_read_data_from_field () failure.
Link: https://github.com/acpica/acpica/commit/d984f120
Link: https://github.com/acpica/acpica/pull/685
Reported-by: Lenny Szubowicz <lszubowi@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cdfe9e346 ]
ACPICA commit c11af67d8f7e3d381068ce7771322f2b5324d687
If original_count is 0 in acpi_ut_update_ref_count (),
acpi_ut_delete_internal_obj () is invoked for the target object, which is
incorrect, because that object has been deleted once already and the
memory allocated to store it may have been reclaimed and allocated
for a different purpose by the host OS. Moreover, a confusing debug
message following the "Reference Count is already zero, cannot
decrement" warning is printed in that case.
To fix this issue, make acpi_ut_update_ref_count () return after finding
that original_count is 0 and printing the above warning.
Link: https://github.com/acpica/acpica/commit/c11af67d
Link: https://github.com/acpica/acpica/pull/652
Reported-by: Mark Asselstine <mark.asselstine@windriver.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f81bdeaf81 ]
ACPICA commit bc02c76d518135531483dfc276ed28b7ee632ce1
The current ACPI_ACCESS_*_WIDTH defines do not provide a way to
test that size is small enough to not cause an overflow when
applied to a 32-bit integer.
Rather than adding more magic numbers, add ACPI_ACCESS_*_SHIFT,
ACPI_ACCESS_*_MAX, and ACPI_ACCESS_*_DEFAULT #defines and
redefine ACPI_ACCESS_*_WIDTH in terms of the new #defines.
This was inititally reported on Linux where a size of 102 in
ACPI_ACCESS_BIT_WIDTH caused an overflow error in the SPCR
initialization code.
Link: https://github.com/acpica/acpica/commit/bc02c76d
Signed-off-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa39cc6757 ]
GC task can deadlock in read_cache_page() because it may attempt
to release a page that is actually allocated by another task in
jffs2_write_begin().
The reason is that in jffs2_write_begin() there is a small window
a cache page is allocated for use but not set Uptodate yet.
This ends up with a deadlock between two tasks:
1) A task (e.g. file copy)
- jffs2_write_begin() locks a cache page
- jffs2_write_end() tries to lock "alloc_sem" from
jffs2_reserve_space() <-- STUCK
2) GC task (jffs2_gcd_mtd3)
- jffs2_garbage_collect_pass() locks "alloc_sem"
- try to lock the same cache page in read_cache_page() <-- STUCK
So to avoid this deadlock, hold "alloc_sem" in jffs2_write_begin()
while reading data in a cache page.
Signed-off-by: Kyeong Yoo <kyeong.yoo@alliedtelesis.co.nz>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdd156955f ]
Some GPU heavy test programs manage to trigger the hangcheck quite often.
If there are no other GPU users in the system and the test program
exhibits a very regular structure in the commandstreams that are being
submitted, we can end up with two distinct submits managing to trigger
the hangcheck with the FE in a very similar address range. This leads
the hangcheck to believe that the GPU is stuck, while in reality the GPU
is already busy working on a different job. To avoid those spurious
GPU resets, also remember and consider the last completed fence seqno
in the hang check.
Reported-by: Joerg Albert <joerg.albert@iav.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e484b3e96 ]
Kernel generates mapping change message, XFRM_MSG_MAPPING,
when a source port chage is detected on a input state with UDP
encapsulation set. Kernel generates a message for each IPsec packet
with new source port. For a high speed flow per packet mapping change
message can be excessive, and can overload the user space listener.
Introduce rate limiting for XFRM_MSG_MAPPING message to the user space.
The rate limiting is configurable via netlink, when adding a new SA or
updating it. Use the new attribute XFRMA_MTIMER_THRESH in seconds.
v1->v2 change:
update xfrm_sa_len()
v2->v3 changes:
use u32 insted unsigned long to reduce size of struct xfrm_state
fix xfrm_ompat size Reported-by: kernel test robot <lkp@intel.com>
accept XFRM_MSG_MAPPING only when XFRMA_ENCAP is present
Co-developed-by: Thomas Egerer <thomas.egerer@secunet.com>
Signed-off-by: Thomas Egerer <thomas.egerer@secunet.com>
Signed-off-by: Antony Antony <antony.antony@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfb4c313be ]
This set HCI_QUIRK_VALID_LE_STATES quirk which is required for the likes
of experimental LE simultaneous roles.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ce708f54c ]
Large pkt_len can lead to out-out-bound memcpy. Current
ath9k_hif_usb_rx_stream allows combining the content of two urb
inputs to one pkt. The first input can indicate the size of the
pkt. Any remaining size is saved in hif_dev->rx_remain_len.
While processing the next input, memcpy is used with rx_remain_len.
4-byte pkt_len can go up to 0xffff, while a single input is 0x4000
maximum in size (MAX_RX_BUF_SIZE). Thus, the patch adds a check for
pkt_len which must not exceed 2 * MAX_RX_BUG_SIZE.
BUG: KASAN: slab-out-of-bounds in ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
Read of size 46393 at addr ffff888018798000 by task kworker/0:1/23
CPU: 0 PID: 23 Comm: kworker/0:1 Not tainted 5.6.0 #63
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS rel-1.10.2-0-g5f4c7b1-prebuilt.qemu-project.org 04/01/2014
Workqueue: events request_firmware_work_func
Call Trace:
<IRQ>
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
? ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
__kasan_report.cold+0x37/0x7c
? ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
kasan_report+0xe/0x20
check_memory_region+0x15a/0x1d0
memcpy+0x20/0x50
ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
? hif_usb_mgmt_cb+0x2d9/0x2d9 [ath9k_htc]
? _raw_spin_lock_irqsave+0x7b/0xd0
? _raw_spin_trylock_bh+0x120/0x120
? __usb_unanchor_urb+0x12f/0x210
__usb_hcd_giveback_urb+0x1e4/0x380
usb_giveback_urb_bh+0x241/0x4f0
? __hrtimer_run_queues+0x316/0x740
? __usb_hcd_giveback_urb+0x380/0x380
tasklet_action_common.isra.0+0x135/0x330
__do_softirq+0x18c/0x634
irq_exit+0x114/0x140
smp_apic_timer_interrupt+0xde/0x380
apic_timer_interrupt+0xf/0x20
I found the bug using a custome USBFuzz port. It's a research work
to fuzz USB stack/drivers. I modified it to fuzz ath9k driver only,
providing hand-crafted usb descriptors to QEMU.
After fixing the value of pkt_tag to ATH_USB_RX_STREAM_MODE_TAG in QEMU
emulation, I found the KASAN report. The bug is triggerable whenever
pkt_len is above two MAX_RX_BUG_SIZE. I used the same input that crashes
to test the driver works when applying the patch.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/YXsidrRuK6zBJicZ@10-18-43-117.dynapool.wireless.nyu.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0055858638 ]
When a new USB device gets plugged to nested hubs, the affected hub,
which connects to usb 2-1.4-port2, doesn't report there's any change,
hence the nested hubs go back to runtime suspend like nothing happened:
[ 281.032951] usb usb2: usb wakeup-resume
[ 281.032959] usb usb2: usb auto-resume
[ 281.032974] hub 2-0:1.0: hub_resume
[ 281.033011] usb usb2-port1: status 0263 change 0000
[ 281.033077] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.049797] usb 2-1: usb wakeup-resume
[ 281.069800] usb 2-1: Waited 0ms for CONNECT
[ 281.069810] usb 2-1: finish resume
[ 281.070026] hub 2-1:1.0: hub_resume
[ 281.070250] usb 2-1-port4: status 0203 change 0000
[ 281.070272] usb usb2-port1: resume, status 0
[ 281.070282] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.089813] usb 2-1.4: usb wakeup-resume
[ 281.109792] usb 2-1.4: Waited 0ms for CONNECT
[ 281.109801] usb 2-1.4: finish resume
[ 281.109991] hub 2-1.4:1.0: hub_resume
[ 281.110147] usb 2-1.4-port2: status 0263 change 0000
[ 281.110234] usb 2-1-port4: resume, status 0
[ 281.110239] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.110266] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.110426] hub 2-1.4:1.0: hub_suspend
[ 281.110565] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.130998] hub 2-1:1.0: hub_suspend
[ 281.137788] usb 2-1: usb auto-suspend, wakeup 1
[ 281.142935] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.177828] usb 2-1: usb wakeup-resume
[ 281.197839] usb 2-1: Waited 0ms for CONNECT
[ 281.197850] usb 2-1: finish resume
[ 281.197984] hub 2-1:1.0: hub_resume
[ 281.198203] usb 2-1-port4: status 0203 change 0000
[ 281.198228] usb usb2-port1: resume, status 0
[ 281.198237] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.217835] usb 2-1.4: usb wakeup-resume
[ 281.237834] usb 2-1.4: Waited 0ms for CONNECT
[ 281.237845] usb 2-1.4: finish resume
[ 281.237990] hub 2-1.4:1.0: hub_resume
[ 281.238067] usb 2-1.4-port2: status 0263 change 0000
[ 281.238148] usb 2-1-port4: resume, status 0
[ 281.238152] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.238166] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.238385] hub 2-1.4:1.0: hub_suspend
[ 281.238523] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.258076] hub 2-1:1.0: hub_suspend
[ 281.265744] usb 2-1: usb auto-suspend, wakeup 1
[ 281.285976] hub 2-0:1.0: hub_suspend
[ 281.285988] usb usb2: bus auto-suspend, wakeup 1
USB 3.2 spec, 9.2.5.4 "Changing Function Suspend State" says that "If
the link is in a non-U0 state, then the device must transition the link
to U0 prior to sending the remote wake message", but the hub only
transits the link to U0 after signaling remote wakeup.
So be more forgiving and use a 20ms delay to let the link transit to U0
for remote wakeup.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20211215120108.336597-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 521223d8b3 ]
The min and max frequency QoS requests in the cpufreq core are
initialized to whatever the current min and max frequency values are
at the init time, but if any of these values change later (for
example, cpuinfo.max_freq is updated by the driver), these initial
request values will be limiting the CPU frequency unnecessarily
unless they are changed by user space via sysfs.
To address this, initialize min_freq_req and max_freq_req to
FREQ_QOS_MIN_DEFAULT_VALUE and FREQ_QOS_MAX_DEFAULT_VALUE,
respectively, so they don't really limit anything until user
space updates them.
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1579e6119 ]
Because refcount_dec_not_one() returns true if the target refcount
becomes saturated, it is generally unsafe to use its return value as
a loop termination condition, but that is what happens when a device
link's supplier device is released during runtime PM suspend
operations and on device link removal.
To address this, introduce pm_runtime_release_supplier() to be used
in the above cases which will check the supplier device's runtime
PM usage counter in addition to the refcount_dec_not_one() return
value, so the loop can be terminated in case the rpm_active refcount
value becomes invalid, and update the code in question to use it as
appropriate.
This change is not expected to have any visible functional impact.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b14cbd643 ]
The Tegra186 CCPLEX cluster register region is 4 MiB is length, not 4
MiB - 1. This was likely presumed to be the "limit" rather than length.
Fix it up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f110f5306 ]
Due to the audit control mutex necessary for serializing audit
userspace messages we haven't been able to block/penalize userspace
processes that attempt to send audit records while the system is
under audit pressure. The result is that privileged userspace
applications have a priority boost with respect to audit as they are
not bound by the same audit queue throttling as the other tasks on
the system.
This patch attempts to restore some balance to the system when under
audit pressure by blocking these privileged userspace tasks after
they have finished their audit processing, and dropped the audit
control mutex, but before they return to userspace.
Reported-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Tested-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c3e5b74b9 ]
The mmc core takes a specific path to support initializing of a
non-standard SDIO card. This is triggered by looking for the card-quirk,
MMC_QUIRK_NONSTD_SDIO.
In mmc_sdio_init_card() this gets rather messy, as it causes the code to
bail out earlier, compared to the usual path. This leads to that the OCR
doesn't get saved properly in card->ocr. Fortunately, only omap_hsmmc has
been using the MMC_QUIRK_NONSTD_SDIO and is dealing with the issue, by
assigning a hardcoded value (0x80) to card->ocr from an ->init_card() ops.
To make the behaviour consistent, let's instead rely on the core to save
the OCR in card->ocr during initialization.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/e7936cff7fc24d187ef2680d3b4edb0ade58f293.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3af86b0469 ]
In hexium_attach(dev, info), saa7146_vv_init() is called to allocate
a new memory for dev->vv_data. saa7146_vv_release() will be called on
failure of saa7146_register_device(). There is a dereference of
dev->vv_data in saa7146_vv_release(), which could lead to a NULL
pointer dereference on failure of saa7146_vv_init().
Fix this bug by adding a check of saa7146_vv_init().
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_VIDEO_HEXIUM_GEMINI=m show no new warnings,
and our static analyzer no longer warns about this code.
Link: https://lore.kernel.org/linux-media/20211203154030.111210-1-zhou1615@umn.edu
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fede658e7 ]
Without this, some IR will be missing mid-stream and we might decode
something which never really occurred.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cbad98903 ]
The WARN_ONCE() in bpf_warn_invalid_xdp_action() can be triggered by
any bugged program, and even attaching a correct program to a NIC
not supporting the given action.
The resulting splat, beyond polluting the logs, fouls automated tools:
e.g. a syzkaller reproducers using an XDP program returning an
unsupported action will never pass validation.
Replace the WARN_ONCE with a less intrusive pr_warn_once().
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/016ceec56e4817ebb2a9e35ce794d5c917df572c.1638189075.git.pabeni@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c7ce80a81 ]
And allow instrumentation inside it because it does calls to other
facilities which will not be tagged noinstr.
Fixes
vmlinux.o: warning: objtool: do_machine_check()+0xc73: call to mce_panic() leaves .noinstr.text section
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20211208111343.8130-8-bp@alien8.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5992f373c ]
Commit 32f6e5da83 ("selftests/ftrace: Add kprobe profile testcase")
added a new kprobes testcase, but has a description which does not
describe what the test case is doing and is duplicating the description
of another test case.
Therefore change the test case description, so it is unique and then
allows easily to tell which test case actually passed or failed.
Reported-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61a7904b6a ]
The gpio-aspeed driver implements an irq_chip which need to be invoked
from hardirq context. Since spin_lock() can sleep with PREEMPT_RT, it is
no longer legal to invoke it while interrupts are disabled.
This also causes lockdep to complain about:
[ 0.649797] [ BUG: Invalid wait context ]
because aspeed_gpio.lock (spin_lock_t) is taken under irq_desc.lock
(raw_spinlock_t).
Let's use of raw_spinlock_t instead of spinlock_t.
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f20f94f7f5 ]
The PHY settings table is supposed to be sorted by descending match
priority - in other words, earlier entries are preferred over later
entries.
The order of 1000baseKX/Full and 1000baseT/Full is such that we
prefer 1000baseKX/Full over 1000baseT/Full, but 1000baseKX/Full is
a lot rarer than 1000baseT/Full, and thus is much less likely to
be preferred.
This causes phylink problems - it means a fixed link specifying a
speed of 1G and full duplex gets an ethtool linkmode of 1000baseKX/Full
rather than 1000baseT/Full as would be expected - and since we offer
userspace a software emulation of a conventional copper PHY, we want
to offer copper modes in preference to anything else. However, we do
still want to allow the rarer modes as well.
Hence, let's reorder these two modes to prefer copper.
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/E1muvFO-00F6jY-1K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7dac08341 ]
When updating Rx and Tx queue kobjects, the queue count should always be
updated to match the queue kobjects count. This was not done in the net
device unregistration path, fix it. Tracking all queue count updates
will allow in a following up patch to detect illegal updates.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
