IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 6045ab5fea4c849153ebeb0acb532da5f29d69c4 upstream.
bFLT binaries are usually created using elf2flt.
The linker script used by elf2flt has defined the .data section like the
following for the last 19 years:
.data : {
_sdata = . ;
__data_start = . ;
data_start = . ;
*(.got.plt)
*(.got)
FILL(0) ;
. = ALIGN(0x20) ;
LONG(-1)
. = ALIGN(0x20) ;
...
}
It places the .got.plt input section before the .got input section.
The same is true for the default linker script (ld --verbose) on most
architectures except x86/x86-64.
The binfmt_flat loader should relocate all GOT entries until it encounters
a -1 (the LONG(-1) in the linker script).
The problem is that the .got.plt input section starts with a GOTPLT header
(which has size 16 bytes on elf64-riscv and 8 bytes on elf32-riscv), where
the first word is set to -1. See the binutils implementation for riscv [1].
This causes the binfmt_flat loader to stop relocating GOT entries
prematurely and thus causes the application to crash when running.
Fix this by skipping the whole GOTPLT header, since the whole GOTPLT header
is reserved for the dynamic linker.
The GOTPLT header will only be skipped for bFLT binaries with flag
FLAT_FLAG_GOTPIC set. This flag is unconditionally set by elf2flt if the
supplied ELF binary has the symbol _GLOBAL_OFFSET_TABLE_ defined.
ELF binaries without a .got input section should thus remain unaffected.
Tested on RISC-V Canaan Kendryte K210 and RISC-V QEMU nommu_virt_defconfig.
[1] https://sourceware.org/git/?p=binutils-gdb.git;a=blob;f=bfd/elfnn-riscv.c;hb=binutils-2_38#l3275
Cc: <stable@vger.kernel.org>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Link: https://lore.kernel.org/r/20220414091018.896737-1-niklas.cassel@wdc.com
Fixed-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/202204182333.OIUOotK8-lkp@intel.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45969b4152c1752089351cd6836a42a566d49bcf upstream.
The data length of skb frags + frag_list may be greater than 0xffff, and
skb_header_pointer can not handle negative offset. So, here INT_MAX is used
to check the validity of offset. Add the same change to the related function
skb_store_bytes.
Fixes: 05c74e5e53f6 ("bpf: add bpf_skb_load_bytes helper")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20220416105801.88708-2-liujian56@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce3c4ad7f4ce5db7b4f08a1e237d8dd94b39180b upstream.
nfsd4_release_lockowner() holds clp->cl_lock when it calls
check_for_locks(). However, check_for_locks() calls nfsd_file_get()
/ nfsd_file_put() to access the backing inode's flc_posix list, and
nfsd_file_put() can sleep if the inode was recently removed.
Let's instead rely on the stateowner's reference count to gate
whether the release is permitted. This should be a reliable
indication of locks-in-use since file lock operations and
->lm_get_owner take appropriate references, which are released
appropriately when file locks are removed.
Reported-by: Dai Ngo <dai.ngo@oracle.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 452284407c18d8a522c3039339b1860afa0025a8 upstream.
We need to filter out ENOMEM in nfs_error_is_fatal_on_server(), because
running out of memory on our client is not a server error.
Reported-by: Olga Kornievskaia <aglo@umich.edu>
Fixes: 2dc23afffbca ("NFS: ENOMEM should also be a fatal error.")
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d5aa418b3bd42cdccc36e94ee199af423ef7c84 upstream.
The reference to `explicit_in_reply_to` is pointless as when the
reference was added in the form of "#15" [1], Section 15) was "The
canonical patch format".
The reference of "#15" had not been properly updated in a couple of
reorganizations during the plain-text SubmittingPatches era.
Fix it by using `the_canonical_patch_format`.
[1]: 2ae19acaa50a ("Documentation: Add "how to write a good patch summary" to SubmittingPatches")
Signed-off-by: Akira Yokosawa <akiyks@gmail.com>
Fixes: 5903019b2a5e ("Documentation/SubmittingPatches: convert it to ReST markup")
Fixes: 9b2c76777acc ("Documentation/SubmittingPatches: enrich the Sphinx output")
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: stable@vger.kernel.org # v4.9+
Link: https://lore.kernel.org/r/64e105a5-50be-23f2-6cae-903a2ea98e18@gmail.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0dc1a7100f19121f6e7450f9cdda11926aa3838 upstream.
Currently it returns zero when CRQ response timed out, it should return
an error code instead.
Fixes: d8d74ea3c002 ("tpm: ibmvtpm: Wait for buffer to be set before proceeding")
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e57b2523bd37e6434f4e64c7a685e3715ad21e9a upstream.
Under certain conditions uninitialized memory will be accessed.
As described by TCG Trusted Platform Module Library Specification,
rev. 1.59 (Part 3: Commands), if a TPM2_GetCapability is received,
requesting a capability, the TPM in field upgrade mode may return a
zero length list.
Check the property count in tpm2_get_tpm_pt().
Fixes: 2ab3241161b3 ("tpm: migrate tpm2_get_tpm_pt() to use struct tpm_buf")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Mahnke-Hartmann <stefan.mahnke-hartmann@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d07cef7fd7599450b3d03e1915efc2a96e1f03f upstream.
The Google Whiskers touchpad does not work properly with the default
multitouch configuration. Instead, use the same configuration as Google
Rose.
Signed-off-by: Marek Maslanka <mm@semihalf.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57668f0a4cc4083a120cc8c517ca0055c4543b59 upstream.
Raid456 module had allowed to achieve failed state. It was fixed by
fb73b357fb9 ("raid5: block failing device if raid will be failed").
This fix introduces a bug, now if raid5 fails during IO, it may result
with a hung task without completion. Faulty flag on the device is
necessary to process all requests and is checked many times, mainly in
analyze_stripe().
Allow to set faulty on drive again and set MD_BROKEN if raid is failed.
As a result, this level is allowed to achieve failed state again, but
communication with userspace (via -EBUSY status) will be preserved.
This restores possibility to fail array via #mdadm --set-faulty command
and will be fixed by additional verification on mdadm side.
Reproduction steps:
mdadm -CR imsm -e imsm -n 3 /dev/nvme[0-2]n1
mdadm -CR r5 -e imsm -l5 -n3 /dev/nvme[0-2]n1 --assume-clean
mkfs.xfs /dev/md126 -f
mount /dev/md126 /mnt/root/
fio --filename=/mnt/root/file --size=5GB --direct=1 --rw=randrw
--bs=64k --ioengine=libaio --iodepth=64 --runtime=240 --numjobs=4
--time_based --group_reporting --name=throughput-test-job
--eta-newline=1 &
echo 1 > /sys/block/nvme2n1/device/device/remove
echo 1 > /sys/block/nvme1n1/device/device/remove
[ 1475.787779] Call Trace:
[ 1475.793111] __schedule+0x2a6/0x700
[ 1475.799460] schedule+0x38/0xa0
[ 1475.805454] raid5_get_active_stripe+0x469/0x5f0 [raid456]
[ 1475.813856] ? finish_wait+0x80/0x80
[ 1475.820332] raid5_make_request+0x180/0xb40 [raid456]
[ 1475.828281] ? finish_wait+0x80/0x80
[ 1475.834727] ? finish_wait+0x80/0x80
[ 1475.841127] ? finish_wait+0x80/0x80
[ 1475.847480] md_handle_request+0x119/0x190
[ 1475.854390] md_make_request+0x8a/0x190
[ 1475.861041] generic_make_request+0xcf/0x310
[ 1475.868145] submit_bio+0x3c/0x160
[ 1475.874355] iomap_dio_submit_bio.isra.20+0x51/0x60
[ 1475.882070] iomap_dio_bio_actor+0x175/0x390
[ 1475.889149] iomap_apply+0xff/0x310
[ 1475.895447] ? iomap_dio_bio_actor+0x390/0x390
[ 1475.902736] ? iomap_dio_bio_actor+0x390/0x390
[ 1475.909974] iomap_dio_rw+0x2f2/0x490
[ 1475.916415] ? iomap_dio_bio_actor+0x390/0x390
[ 1475.923680] ? atime_needs_update+0x77/0xe0
[ 1475.930674] ? xfs_file_dio_aio_read+0x6b/0xe0 [xfs]
[ 1475.938455] xfs_file_dio_aio_read+0x6b/0xe0 [xfs]
[ 1475.946084] xfs_file_read_iter+0xba/0xd0 [xfs]
[ 1475.953403] aio_read+0xd5/0x180
[ 1475.959395] ? _cond_resched+0x15/0x30
[ 1475.965907] io_submit_one+0x20b/0x3c0
[ 1475.972398] __x64_sys_io_submit+0xa2/0x180
[ 1475.979335] ? do_io_getevents+0x7c/0xc0
[ 1475.986009] do_syscall_64+0x5b/0x1a0
[ 1475.992419] entry_SYSCALL_64_after_hwframe+0x65/0xca
[ 1476.000255] RIP: 0033:0x7f11fc27978d
[ 1476.006631] Code: Bad RIP value.
[ 1476.073251] INFO: task fio:3877 blocked for more than 120 seconds.
Cc: stable@vger.kernel.org
Fixes: fb73b357fb9 ("raid5: block failing device if raid will be failed")
Reviewd-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@linux.intel.com>
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4caae58406f8ceb741603eee460d79bacca9b1b5 upstream.
The device-mapper framework provides a mechanism to mark targets as
immutable (and hence fail table reloads that try to change the target
type). Add the DM_TARGET_IMMUTABLE flag to the dm-verity target's
feature flags to prevent switching the verity target with a different
target type.
Fixes: a4ffc152198e ("dm: add verity target")
Cc: stable@vger.kernel.org
Signed-off-by: Sarthak Kukreti <sarthakkukreti@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfe2b0146c4d0230b68f5c71a64380ff8d361f8b upstream.
dm-stats can be used with a very large number of entries (it is only
limited by 1/4 of total system memory), so add rescheduling points to
the loops that iterate over the entries.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 567dd8f34560fa221a6343729474536aa7ede4fd upstream.
The device mapper dm-crypt target is using scnprintf("%02x", cc->key[i]) to
report the current key to userspace. However, this is not a constant-time
operation and it may leak information about the key via timing, via cache
access patterns or via the branch predictor.
Change dm-crypt's key printing to use "%c" instead of "%02x". Also
introduce hex2asc() that carefully avoids any branching or memory
accesses when converting a number in the range 0 ... 15 to an ascii
character.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3f2a14b8906df913cb04a706367b012db94a6e8 upstream.
The "r" variable shadows an earlier "r" that has function scope. It
means that we accidentally return success instead of an error code.
Smatch has a warning for this:
drivers/md/dm-integrity.c:4503 dm_integrity_ctr()
warn: missing error code 'r'
Fixes: 7eada909bfd7 ("dm: add integrity target")
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2505a981114dcb715f8977b8433f7540854851d8 upstream.
The asynchronous zspage free worker tries to lock a zspage's entire page
list without defending against page migration. Since pages which haven't
yet been locked can concurrently migrate off the zspage page list while
lock_zspage() churns away, lock_zspage() can suffer from a few different
lethal races.
It can lock a page which no longer belongs to the zspage and unsafely
dereference page_private(), it can unsafely dereference a torn pointer to
the next page (since there's a data race), and it can observe a spurious
NULL pointer to the next page and thus not lock all of the zspage's pages
(since a single page migration will reconstruct the entire page list, and
create_page_chain() unconditionally zeroes out each list pointer in the
process).
Fix the races by using migrate_read_lock() in lock_zspage() to synchronize
with page migration.
Link: https://lkml.kernel.org/r/20220509024703.243847-1-sultan@kerneltoast.com
Fixes: 77ff465799c602 ("zsmalloc: zs_page_migrate: skip unnecessary loops but not return -EBUSY if zspage is not inuse")
Signed-off-by: Sultan Alsawaf <sultan@kerneltoast.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56b14ecec97f39118bf85c9ac2438c5a949509ed upstream.
In case the conntrack is clashing, insertion can free skb->_nfct and
set skb->_nfct to the already-confirmed entry.
This wasn't found before because the conntrack entry and the extension
space used to free'd after an rcu grace period, plus the race needs
events enabled to trigger.
Reported-by: <syzbot+793a590957d9c1b96620@syzkaller.appspotmail.com>
Fixes: 71d8c47fc653 ("netfilter: conntrack: introduce clash resolution on insertion race")
Fixes: 2ad9d7747c10 ("netfilter: conntrack: free extension area immediately")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcd46d897adb70d63e025f175a00a89797d31a43 upstream.
Quoting[1] Ariadne Conill:
"In several other operating systems, it is a hard requirement that the
second argument to execve(2) be the name of a program, thus prohibiting
a scenario where argc < 1. POSIX 2017 also recommends this behaviour,
but it is not an explicit requirement[2]:
The argument arg0 should point to a filename string that is
associated with the process being started by one of the exec
functions.
...
Interestingly, Michael Kerrisk opened an issue about this in 2008[3],
but there was no consensus to support fixing this issue then.
Hopefully now that CVE-2021-4034 shows practical exploitative use[4]
of this bug in a shellcode, we can reconsider.
This issue is being tracked in the KSPP issue tracker[5]."
While the initial code searches[6][7] turned up what appeared to be
mostly corner case tests, trying to that just reject argv == NULL
(or an immediately terminated pointer list) quickly started tripping[8]
existing userspace programs.
The next best approach is forcing a single empty string into argv and
adjusting argc to match. The number of programs depending on argc == 0
seems a smaller set than those calling execve with a NULL argv.
Account for the additional stack space in bprm_stack_limits(). Inject an
empty string when argc == 0 (and set argc = 1). Warn about the case so
userspace has some notice about the change:
process './argc0' launched './argc0' with NULL argv: empty string added
Additionally WARN() and reject NULL argv usage for kernel threads.
[1] https://lore.kernel.org/lkml/20220127000724.15106-1-ariadne@dereferenced.org/
[2] https://pubs.opengroup.org/onlinepubs/9699919799/functions/exec.html
[3] https://bugzilla.kernel.org/show_bug.cgi?id=8408
[4] https://www.qualys.com/2022/01/25/cve-2021-4034/pwnkit.txt
[5] https://github.com/KSPP/linux/issues/176
[6] https://codesearch.debian.net/search?q=execve%5C+*%5C%28%5B%5E%2C%5D%2B%2C+*NULL&literal=0
[7] https://codesearch.debian.net/search?q=execlp%3F%5Cs*%5C%28%5B%5E%2C%5D%2B%2C%5Cs*NULL&literal=0
[8] https://lore.kernel.org/lkml/20220131144352.GE16385@xsang-OptiPlex-9020/
Reported-by: Ariadne Conill <ariadne@dereferenced.org>
Reported-by: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Christian Brauner <brauner@kernel.org>
Acked-by: Ariadne Conill <ariadne@dereferenced.org>
Acked-by: Andy Lutomirski <luto@kernel.org>
Link: https://lore.kernel.org/r/20220201000947.2453721-1-keescook@chromium.org
[vegard: fixed conflicts due to missing
886d7de631da71e30909980fdbf318f7caade262^- and
3950e975431bc914f7e81b8f2a2dbdf2064acb0f^-]
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 336feb502a715909a8136eb6a62a83d7268a353b upstream.
Fix the following -Wstringop-overflow warnings when building with GCC-11:
drivers/gpu/drm/i915/intel_pm.c:3106:9: warning: ‘intel_read_wm_latency’ accessing 16 bytes in a region of size 10 [-Wstringop-overflow=]
3106 | intel_read_wm_latency(dev_priv, dev_priv->wm.pri_latency);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/intel_pm.c:3106:9: note: referencing argument 2 of type ‘u16 *’ {aka ‘short unsigned int *’}
drivers/gpu/drm/i915/intel_pm.c:2861:13: note: in a call to function ‘intel_read_wm_latency’
2861 | static void intel_read_wm_latency(struct drm_i915_private *dev_priv,
| ^~~~~~~~~~~~~~~~~~~~~
by removing the over-specified array size from the argument declarations.
It seems that this code is actually safe because the size of the
array depends on the hardware generation, and the function checks
for that.
Notice that wm can be an array of 5 elements:
drivers/gpu/drm/i915/intel_pm.c:3109: intel_read_wm_latency(dev_priv, dev_priv->wm.pri_latency);
or an array of 8 elements:
drivers/gpu/drm/i915/intel_pm.c:3131: intel_read_wm_latency(dev_priv, dev_priv->wm.skl_latency);
and the compiler legitimately complains about that.
This helps with the ongoing efforts to globally enable
-Wstringop-overflow.
Link: https://github.com/KSPP/linux/issues/181
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b7b3ac8ff3317cdcf07a1c413de9bdb68019c2b upstream.
We used to set regulatory info before the registration of
the device and then the regulatory info didn't get set, because
the device isn't registered so there isn't a device to set the
regulatory info for. So set the regulatory info after the device
registration.
Call reg_process_self_managed_hints() once again after the device
registration because it does nothing before it.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.c96eadcffe80.I86799c2c866b5610b4cf91115c21d8ceb525c5aa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1dc87763f406d4e67caf16dbe438a5647692395 upstream.
A rare BUG_ON triggered in assoc_array_gc:
[3430308.818153] kernel BUG at lib/assoc_array.c:1609!
Which corresponded to the statement currently at line 1593 upstream:
BUG_ON(assoc_array_ptr_is_meta(p));
Using the data from the core dump, I was able to generate a userspace
reproducer[1] and determine the cause of the bug.
[1]: https://github.com/brenns10/kernel_stuff/tree/master/assoc_array_gc
After running the iterator on the entire branch, an internal tree node
looked like the following:
NODE (nr_leaves_on_branch: 3)
SLOT [0] NODE (2 leaves)
SLOT [1] NODE (1 leaf)
SLOT [2..f] NODE (empty)
In the userspace reproducer, the pr_devel output when compressing this
node was:
-- compress node 0x5607cc089380 --
free=0, leaves=0
[0] retain node 2/1 [nx 0]
[1] fold node 1/1 [nx 0]
[2] fold node 0/1 [nx 2]
[3] fold node 0/2 [nx 2]
[4] fold node 0/3 [nx 2]
[5] fold node 0/4 [nx 2]
[6] fold node 0/5 [nx 2]
[7] fold node 0/6 [nx 2]
[8] fold node 0/7 [nx 2]
[9] fold node 0/8 [nx 2]
[10] fold node 0/9 [nx 2]
[11] fold node 0/10 [nx 2]
[12] fold node 0/11 [nx 2]
[13] fold node 0/12 [nx 2]
[14] fold node 0/13 [nx 2]
[15] fold node 0/14 [nx 2]
after: 3
At slot 0, an internal node with 2 leaves could not be folded into the
node, because there was only one available slot (slot 0). Thus, the
internal node was retained. At slot 1, the node had one leaf, and was
able to be folded in successfully. The remaining nodes had no leaves,
and so were removed. By the end of the compression stage, there were 14
free slots, and only 3 leaf nodes. The tree was ascended and then its
parent node was compressed. When this node was seen, it could not be
folded, due to the internal node it contained.
The invariant for compression in this function is: whenever
nr_leaves_on_branch < ASSOC_ARRAY_FAN_OUT, the node should contain all
leaf nodes. The compression step currently cannot guarantee this, given
the corner case shown above.
To fix this issue, retry compression whenever we have retained a node,
and yet nr_leaves_on_branch < ASSOC_ARRAY_FAN_OUT. This second
compression will then allow the node in slot 1 to be folded in,
satisfying the invariant. Below is the output of the reproducer once the
fix is applied:
-- compress node 0x560e9c562380 --
free=0, leaves=0
[0] retain node 2/1 [nx 0]
[1] fold node 1/1 [nx 0]
[2] fold node 0/1 [nx 2]
[3] fold node 0/2 [nx 2]
[4] fold node 0/3 [nx 2]
[5] fold node 0/4 [nx 2]
[6] fold node 0/5 [nx 2]
[7] fold node 0/6 [nx 2]
[8] fold node 0/7 [nx 2]
[9] fold node 0/8 [nx 2]
[10] fold node 0/9 [nx 2]
[11] fold node 0/10 [nx 2]
[12] fold node 0/11 [nx 2]
[13] fold node 0/12 [nx 2]
[14] fold node 0/13 [nx 2]
[15] fold node 0/14 [nx 2]
internal nodes remain despite enough space, retrying
-- compress node 0x560e9c562380 --
free=14, leaves=1
[0] fold node 2/15 [nx 0]
after: 3
Changes
=======
DH:
- Use false instead of 0.
- Reorder the inserted lines in a couple of places to put retained before
next_slot.
ver #2)
- Fix typo in pr_devel, correct comparison to "<="
Fixes: 3cb989501c26 ("Add a generic associative array implementation.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Andrew Morton <akpm@linux-foundation.org>
cc: keyrings@vger.kernel.org
Link: https://lore.kernel.org/r/20220511225517.407935-1-stephen.s.brennan@oracle.com/ # v1
Link: https://lore.kernel.org/r/20220512215045.489140-1-stephen.s.brennan@oracle.com/ # v2
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 03a35bc856ddc09f2cc1f4701adecfbf3b464cb3 ]
Due to i2c->adap.dev.fwnode not being set, ACPI_COMPANION() wasn't properly
found for TWSI controllers.
Signed-off-by: Szymon Balcerak <sbalcerak@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17a0f3acdc6ec8b89ad40f6e22165a4beee25663 ]
Before sending a MSI the hardware writes information pertinent to the
interrupt cause to a memory location pointed by SMTICL register. This
memory holds three double words where the least significant bit tells
whether the interrupt cause of master/target/error is valid. The driver
does not use this but we need to set it up because otherwise it will
perform DMA write to the default address (0) and this will cause an
IOMMU fault such as below:
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write] Request device [00:12.0] PASID ffffffff fault addr 0
[fault reason 05] PTE Write access is not set
To prevent this from happening, provide a proper DMA buffer for this
that then gets mapped by the IOMMU accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: From: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fd45e79e8b93b8d22fb8fe22c32fbad7e9190bd ]
The AST2600 when using the i210 NIC over NC-SI has been observed to
produce incorrect checksum results with specific MTU values. This was
first observed when sending data across a long distance set of networks.
On a local network, the following test was performed using a 1MB file of
random data.
On the receiver run this script:
#!/bin/bash
while [ 1 ]; do
# Zero the stats
nstat -r > /dev/null
nc -l 9899 > test-file
# Check for checksum errors
TcpInCsumErrors=$(nstat | grep TcpInCsumErrors)
if [ -z "$TcpInCsumErrors" ]; then
echo No TcpInCsumErrors
else
echo TcpInCsumErrors = $TcpInCsumErrors
fi
done
On an AST2600 system:
# nc <IP of receiver host> 9899 < test-file
The test was repeated with various MTU values:
# ip link set mtu 1410 dev eth0
The observed results:
1500 - good
1434 - bad
1400 - good
1410 - bad
1420 - good
The test was repeated after disabling tx checksumming:
# ethtool -K eth0 tx-checksumming off
And all MTU values tested resulted in transfers without error.
An issue with the driver cannot be ruled out, however there has been no
bug discovered so far.
David has done the work to take the original bug report of slow data
transfer between long distance connections and triaged it down to this
test case.
The vendor suspects this this is a hardware issue when using NC-SI. The
fixes line refers to the patch that introduced AST2600 support.
Reported-by: David Wilder <wilder@us.ibm.com>
Reviewed-by: Dylan Hung <dylan_hung@aspeedtech.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 015c44d7bff3f44d569716117becd570c179ca32 ]
Since the recent introduction supporting the SM3 and SM4 hash algos for IPsec, the kernel
produces invalid pfkey acquire messages, when these encryption modules are disabled. This
happens because the availability of the algos wasn't checked in all necessary functions.
This patch adds these checks.
Signed-off-by: Thomas Bartschies <thomas.bartschies@cvk.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa8785e5931367e2b43f2c507f26bcf3e281c0ca ]
Change suniv f1c100s pinctrl,PD14 multiplexing function lvds1 to uart2
When the pin PD13 and PD14 is setting up to uart2 function in dts,
there's an error occurred:
1c20800.pinctrl: unsupported function uart2 on pin PD14
Because 'uart2' is not any one multiplexing option of PD14,
and pinctrl don't know how to configure it.
So change the pin PD14 lvds1 function to uart2.
Signed-off-by: IotaHydrae <writeforever@foxmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/tencent_70C1308DDA794C81CAEF389049055BACEC09@qq.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1bbc21785b7336619fb6a67f1fff5afdaf229acc upstream.
Currently the sysfs interface maps the BERT error region as "memory"
(through acpi_os_map_memory()) in order to copy the error records into
memory buffers through memory operations (eg memory_read_from_buffer()).
The OS system cannot detect whether the BERT error region is part of
system RAM or it is "device memory" (eg BMC memory) and therefore it
cannot detect which memory attributes the bus to memory support (and
corresponding kernel mapping, unless firmware provides the required
information).
The acpi_os_map_memory() arch backend implementation determines the
mapping attributes. On arm64, if the BERT error region is not present in
the EFI memory map, the error region is mapped as device-nGnRnE; this
triggers alignment faults since memcpy unaligned accesses are not
allowed in device-nGnRnE regions.
The ACPI sysfs code cannot therefore map by default the BERT error
region with memory semantics but should use a safer default.
Change the sysfs code to map the BERT error region as MMIO (through
acpi_os_map_iomem()) and use the memcpy_fromio() interface to read the
error region into the kernel buffer.
Link: https://lore.kernel.org/linux-arm-kernel/31ffe8fc-f5ee-2858-26c5-0fd8bdd68702@arm.com
Link: https://lore.kernel.org/linux-acpi/CAJZ5v0g+OVbhuUUDrLUCfX_mVqY_e8ubgLTU98=jfjTeb4t+Pw@mail.gmail.com
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Veronika Kabatova <vkabatov@redhat.com>
Tested-by: Aristeu Rozanski <aris@redhat.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bdd56d7d8931e842775d2e5b93d426a8d1940e33 upstream.
Sparse is not happy about address space in use in acpi_data_show():
drivers/acpi/sysfs.c:428:14: warning: incorrect type in assignment (different address spaces)
drivers/acpi/sysfs.c:428:14: expected void [noderef] __iomem *base
drivers/acpi/sysfs.c:428:14: got void *
drivers/acpi/sysfs.c:431:59: warning: incorrect type in argument 4 (different address spaces)
drivers/acpi/sysfs.c:431:59: expected void const *from
drivers/acpi/sysfs.c:431:59: got void [noderef] __iomem *base
drivers/acpi/sysfs.c:433:30: warning: incorrect type in argument 1 (different address spaces)
drivers/acpi/sysfs.c:433:30: expected void *logical_address
drivers/acpi/sysfs.c:433:30: got void [noderef] __iomem *base
Indeed, acpi_os_map_memory() returns a void pointer with dropped specific
address space. Hence, we don't need to carry out __iomem in acpi_data_show().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a28dce222a6ece725689ad58c0cf4a1b48894f4 upstream.
Before the video device node is registered, the v4l2_dev.mdev
pointer must be set in order to correctly associate the video
device with the media device. Move the initialization of the
media device up.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf7f34777a5b4100a3a44ff95f3d949c62892bdd upstream.
Prevent NULL (or close to NULL) pointer dereference in various places by
registering the video device only when the V4L2 m2m framework has been set
up.
Fixes: commit 96d8eab5d0a1 ("V4L/DVB: [v5,2/2] v4l: Add a mem-to-mem videobuf framework test device")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2d057560b8107c633b39aabe517ff9d93f285e3 upstream.
SipHash replaced MD5 in secure_ipv{4,6}_port_ephemeral() via commit
7cd23e5300c1 ("secure_seq: use SipHash in place of MD5"), but the output
remained truncated to 32-bit only. In order to exploit more bits from the
hash, let's make the functions return the full 64-bit of siphash_3u32().
We also make sure the port offset calculation in __inet_hash_connect()
remains done on 32-bit to avoid the need for div_u64_rem() and an extra
cost on 32-bit systems.
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Moshe Kol <moshe.kol@mail.huji.ac.il>
Cc: Yossi Gilad <yossi.gilad@mail.huji.ac.il>
Cc: Amit Klein <aksecurity@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[SG: Adjusted context]
Signed-off-by: Stefan Ghinea <stefan.ghinea@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 190cc82489f46f9d88e73c81a47e14f80a791e1a upstream.
RFC 6056 (Recommendations for Transport-Protocol Port Randomization)
provides good summary of why source selection needs extra care.
David Dworken reminded us that linux implements Algorithm 3
as described in RFC 6056 3.3.3
Quoting David :
In the context of the web, this creates an interesting info leak where
websites can count how many TCP connections a user's computer is
establishing over time. For example, this allows a website to count
exactly how many subresources a third party website loaded.
This also allows:
- Distinguishing between different users behind a VPN based on
distinct source port ranges.
- Tracking users over time across multiple networks.
- Covert communication channels between different browsers/browser
profiles running on the same computer
- Tracking what applications are running on a computer based on
the pattern of how fast source ports are getting incremented.
Section 3.3.4 describes an enhancement, that reduces
attackers ability to use the basic information currently
stored into the shared 'u32 hint'.
This change also decreases collision rate when
multiple applications need to connect() to
different destinations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: David Dworken <ddworken@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stefan Ghinea <stefan.ghinea@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24ef83f6e31d20fc121a7cd732b04b498475fca3 upstream.
The goodix panel sends spurious interrupts after a 'finger up' event,
which always cause a timeout.
We were exiting the interrupt handler by reporting touch_num == 0, but
this was still processed as valid and caused the code to use the
uninitialised point_data, creating spurious key release events.
Report an error from the interrupt handler so as to avoid processing
invalid point_data further.
Signed-off-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200316075302.3759-2-dmastykin@astralinux.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code has a check to prevent read overflow but it needs another
check to prevent writing beyond the end of the ->Ssid[] array.
Fixes: 554c0a3abf21 ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Denis Efremov (Oracle) <efremov@linux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e0815b3e09986d2fe651199363e135b9358132a upstream.
When a XEN_HVM guest uses the XEN PIRQ/Eventchannel mechanism, then
PCI/MSI[-X] masking is solely controlled by the hypervisor, but contrary to
XEN_PV guests this does not disable PCI/MSI[-X] masking in the PCI/MSI
layer.
This can lead to a situation where the PCI/MSI layer masks an MSI[-X]
interrupt and the hypervisor grants the write despite the fact that it
already requested the interrupt. As a consequence interrupt delivery on the
affected device is not happening ever.
Set pci_msi_ignore_mask to prevent that like it's done for XEN_PV guests
already.
Fixes: 809f9267bbab ("xen: map MSIs into pirqs")
Reported-by: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com>
Reported-by: Dusty Mabe <dustymabe@redhat.com>
Reported-by: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Noah Meyerhans <noahm@debian.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87tuaduxj5.ffs@tglx
[nmeyerha@amazon.com: backported to 5.4]
Signed-off-by: Noah Meyerhans <nmeyerha@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eadb2f47a3ced5c64b23b90fd2a3463f63726066 upstream.
KGDB and KDB allow read and write access to kernel memory, and thus
should be restricted during lockdown. An attacker with access to a
serial port (for example, via a hypervisor console, which some cloud
vendors provide over the network) could trigger the debugger so it is
important that the debugger respect the lockdown mode when/if it is
triggered.
Fix this by integrating lockdown into kdb's existing permissions
mechanism. Unfortunately kgdb does not have any permissions mechanism
(although it certainly could be added later) so, for now, kgdb is simply
and brutally disabled by immediately exiting the gdb stub without taking
any action.
For lockdowns established early in the boot (e.g. the normal case) then
this should be fine but on systems where kgdb has set breakpoints before
the lockdown is enacted than "bad things" will happen.
CVE: CVE-2022-21499
Co-developed-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Signed-off-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2aeb8c86d49967552394d5e723f87454cb53f501 ]
If a callback break occurs (change notification), afs_getattr() needs to
issue an FS.FetchStatus RPC operation to update the status of the file
being examined by the stat-family of system calls.
Fix afs_getattr() to do this if AFS_VNODE_CB_PROMISED has been cleared
on a vnode by a callback break. Skip this if AT_STATX_DONT_SYNC is set.
This can be tested by appending to a file on one AFS client and then
using "stat -L" to examine its length on a machine running kafs. This
can also be watched through tracing on the kafs machine. The callback
break is seen:
kworker/1:1-46 [001] ..... 978.910812: afs_cb_call: c=0000005f YFSCB.CallBack
kworker/1:1-46 [001] ...1. 978.910829: afs_cb_break: 100058:23b4c:242d2c2 b=2 s=1 break-cb
kworker/1:1-46 [001] ..... 978.911062: afs_call_done: c=0000005f ret=0 ab=0 [0000000082994ead]
And then the stat command generated no traffic if unpatched, but with
this change a call to fetch the status can be observed:
stat-4471 [000] ..... 986.744122: afs_make_fs_call: c=000000ab 100058:023b4c:242d2c2 YFS.FetchStatus
stat-4471 [000] ..... 986.745578: afs_call_done: c=000000ab ret=0 ab=0 [0000000087fc8c84]
Fixes: 08e0e7c82eea ("[AF_RXRPC]: Make the in-kernel AFS filesystem use AF_RXRPC.")
Reported-by: Markus Suvanto <markus.suvanto@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
Tested-by: kafs-testing+fedora34_64checkkafs-build-496@auristor.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216010
Link: https://lore.kernel.org/r/165308359800.162686.14122417881564420962.stgit@warthog.procyon.org.uk/ # v1
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9af9dcf11bda3e2c0e24c1acaacb8685ad974e93 upstream.
The asm_cpu_bringup_and_idle() function is required to push the return
value on the stack in order to make ORC happy, but the only reason
objtool doesn't complain is because of a happy accident.
The thing is that asm_cpu_bringup_and_idle() doesn't return, so
validate_branch() never terminates and falls through to the next
function, which in the normal case is the hypercall_page. And that, as
it happens, is 4095 NOPs and a RET.
Make asm_cpu_bringup_and_idle() terminate on it's own, by making the
function it calls as a dead-end. This way we no longer rely on what
code happens to come after.
Fixes: c3881eb58d56 ("x86/xen: Make the secondary CPU idle tasks reliable")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Link: https://lore.kernel.org/r/20210624095147.693801717@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6f34f4c6b4a962eb7a86c923fea206f866a40be upstream.
Commit 2f62f36e62daec ("x86/xen: Make the boot CPU idle task reliable")
introduced a regression for booting 32 bit Xen PV guests: the address
of the initial stack needs to be a virtual one.
Fixes: 2f62f36e62daec ("x86/xen: Make the boot CPU idle task reliable")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20200409070001.16675-1-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 901c7280ca0d5e2b4a8929fbe0bfb007ac2a6544 upstream.
Halil Pasic points out [1] that the full revert of that commit (revert
in bddac7c1e02b), and that a partial revert that only reverts the
problematic case, but still keeps some of the cleanups is probably
better. 
And that partial revert [2] had already been verified by Oleksandr
Natalenko to also fix the issue, I had just missed that in the long
discussion.
So let's reinstate the cleanups from commit aa6f8dcbab47 ("swiotlb:
rework "fix info leak with DMA_FROM_DEVICE""), and effectively only
revert the part that caused problems.
Link: https://lore.kernel.org/all/20220328013731.017ae3e3.pasic@linux.ibm.com/ [1]
Link: https://lore.kernel.org/all/20220324055732.GB12078@lst.de/ [2]
Link: https://lore.kernel.org/all/4386660.LvFx2qVVIh@natalenko.name/ [3]
Suggested-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Cc: Christoph Hellwig" <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[OP: backport to 5.4: adjusted context]
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4cb7df64c732b2b9918424095c11660c2a8c4a33 upstream.
The audio_mclk_root_clk was added as a gate with the CCGR121 (0x4790),
but according to the reference manual, there is no such gate. Moreover,
the consumer driver of the mentioned clock might gate it and leave
the ECSPI2 (the true owner of that gate) hanging. So lets use the
audio_mclk_post_div, which is the parent.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
[ps: backport to 5.4]
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 581dd69830341d299b0c097fc366097ab497d679 upstream.
Device drivers may decide to not load firmware when probed to avoid
slowing down the boot process should the firmware filesystem not be
available yet. In this case, the firmware loading request may be done
when a device file associated with the driver is first accessed. The
credentials of the userspace process accessing the device file may be
used to validate access to the firmware files requested by the driver.
Ensure that the kernel assumes the responsibility of reading the
firmware.
This was observed on Android for a graphic driver loading their firmware
when the device file (e.g. /dev/mali0) was first opened by userspace
(i.e. surfaceflinger). The security context of surfaceflinger was used
to validate the access to the firmware file (e.g.
/vendor/firmware/mali.bin).
Previously, Android configurations were not setting up the
firmware_class.path command line argument and were relying on the
userspace fallback mechanism. In this case, the security context of the
userspace daemon (i.e. ueventd) was consistently used to read firmware
files. More Android devices are now found to set firmware_class.path
which gives the kernel the opportunity to read the firmware directly
(via kernel_read_file_from_path_initns). In this scenario, the current
process credentials were used, even if unrelated to the loading of the
firmware file.
Signed-off-by: Thiébaud Weksteen <tweek@google.com>
Cc: <stable@vger.kernel.org> # 5.10
Reviewed-by: Paul Moore <paul@paul-moore.com>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20220502004952.3970800-1-tweek@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47f753c1108e287edb3e27fad8a7511a9d55578e upstream.
Based on DesignWare Ethernet QoS datasheet, we are seeing the limitation
of Split Header (SPH) feature is not supported for Ipv4 fragmented packet.
This SPH limitation will cause ping failure when the packets size exceed
the MTU size. For example, the issue happens once the basic ping packet
size is larger than the configured MTU size and the data is lost inside
the fragmented packet, replaced by zeros/corrupted values, and leads to
ping fail.
So, disable the Split Header for Intel platforms.
v2: Add fixes tag in commit message.
Fixes: 67afd6d1cfdf("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Cc: <stable@vger.kernel.org> # 5.10.x
Suggested-by: Ong, Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 866663b7b52d2da267b28e12eed89ee781b8fed1 upstream.
When merging one bio to request, if they are discard IO and the queue
supports multi-range discard, we need to return ELEVATOR_DISCARD_MERGE
because both block core and related drivers(nvme, virtio-blk) doesn't
handle mixed discard io merge(traditional IO merge together with
discard merge) well.
Fix the issue by returning ELEVATOR_DISCARD_MERGE in this situation,
so both blk-mq and drivers just need to handle multi-range discard.
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Fixes: 2705dfb20947 ("block: fix discard request merge")
Link: https://lore.kernel.org/r/20210729034226.1591070-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4920d42ce0e9c8aafb7f64b6d9d4ae02161e51e upstream.
According to Ilitek "231x & ILI251x Programming Guide" Version: 2.30
"2.1. Power Sequence", "T4 Chip Reset and discharge time" is minimum
10ms and "T2 Chip initial time" is maximum 150ms. Adjust the reset
timings such that T4 is 12ms and T2 is 160ms to fit those figures.
This prevents sporadic touch controller start up failures when some
systems with at least ILI251x controller boot, without this patch
the systems sometimes fail to communicate with the touch controller.
Fixes: 201f3c803544c ("Input: ili210x - add reset GPIO support")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220518204901.93534-1-marex@denx.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2120b7f4d128433ad8c5f503a9584deba0684901 ]
Bounds check hw_head index provided by NIC to verify it lies
within the TX buffer ring.
Reported-by: Aashay Shringarpure <aashay@google.com>
Reported-by: Yi Chou <yich@google.com>
Reported-by: Shervin Oloumi <enlightened@google.com>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51ca86b4c9c7c75f5630fa0dbe5f8f0bd98e3c3e ]
Fix the missing pci_disable_device() before return
from tulip_init_one() in the error handling case.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220506094250.3630615-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
