IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Ben Hutchings says:
====================
Fixes for sh_eth #3
I'm continuing review and testing of Ethernet support on the R-Car H2
chip. This series fixes the last of the more serious issues I've found.
These are not tested on any of the other supported chips.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use the return value of dma_map_single(), rather than calling
virt_to_page() separately
- Check for mapping failue
- Call dma_unmap_single() rather than dma_sync_single_for_cpu()
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_map_single() may fail if an IOMMU or swiotlb is in use, so
we need to check for this.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we try to clear EDRRR and EDTRR and immediately continue to
free buffers. This is unsafe because:
- In general, register writes are not serialised with DMA, so we still
have to wait for DMA to complete somehow
- The R8A7790 (R-Car H2) manual states that the TX running flag cannot
be cleared by writing to EDTRR
- The same manual states that clearing the RX running flag only stops
RX DMA at the next packet boundary
I applied this patch to the driver to detect DMA writes to freed
buffers:
> --- a/drivers/net/ethernet/renesas/sh_eth.c
> +++ b/drivers/net/ethernet/renesas/sh_eth.c
> @@ -1098,7 +1098,14 @@ static void sh_eth_ring_free(struct net_device *ndev)
> /* Free Rx skb ringbuffer */
> if (mdp->rx_skbuff) {
> for (i = 0; i < mdp->num_rx_ring; i++)
> + memcpy(mdp->rx_skbuff[i]->data,
> + "Hello, world", 12);
> + msleep(100);
> + for (i = 0; i < mdp->num_rx_ring; i++) {
> + WARN_ON(memcmp(mdp->rx_skbuff[i]->data,
> + "Hello, world", 12));
> dev_kfree_skb(mdp->rx_skbuff[i]);
> + }
> }
> kfree(mdp->rx_skbuff);
> mdp->rx_skbuff = NULL;
then ran the loop:
while ethtool -G eth0 rx 128 ; ethtool -G eth0 rx 64; do echo -n .; done
and 'ping -f' toward the sh_eth port from another machine. The
warning fired several times a minute.
To fix these issues:
- Deactivate all TX descriptors rather than writing to EDTRR
- As there seems to be no way of telling when RX DMA is stopped,
perform a soft reset to ensure that both DMA enginess are stopped
- To reduce the possibility of the reset truncating a transmitted
frame, disable egress and wait a reasonable time to reach a
packet boundary before resetting
- Update statistics before resetting
(The 'reasonable time' does not allow for CS/CD in half-duplex
mode, but half-duplex no longer seems reasonable!)
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If RX traffic is overflowing the FIFO or DMA ring, logging every time
this happens just makes things worse. These errors are visible in the
statistics anyway.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=S/gP
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-3.19-20150127' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-01-27
this is another pull request for net/master which consists of 4 patches.
All 4 patches are contributed by Ahmed S. Darwish, he fixes more problems in
the kvaser_usb driver.
David, please merge net/master to net-next/master, as we have more kvaser_usb
patches in the queue, that target net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
An exception is seen in ICMP ping receive path where the skb
destructor sock_rfree() tries to access a freed socket. This happens
because ping_rcv() releases socket reference with sock_put() and this
internally frees up the socket. Later icmp_rcv() will try to free the
skb and as part of this, skb destructor is called and which leads
to a kernel panic as the socket is freed already in ping_rcv().
-->|exception
-007|sk_mem_uncharge
-007|sock_rfree
-008|skb_release_head_state
-009|skb_release_all
-009|__kfree_skb
-010|kfree_skb
-011|icmp_rcv
-012|ip_local_deliver_finish
Fix this incorrect free by cloning this skb and processing this cloned
skb instead.
This patch was suggested by Eric Dumazet
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on rhashtable walking I noticed that the UDP diag
dumping code is buggy. In particular, the socket skipping within
a chain never happens, even though we record the number of sockets
that should be skipped.
As this code was supposedly copied from TCP, this patch does what
TCP does and resets num before we walk a chain.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While being in an ERROR_WARNING state, and receiving further
bus error events with error counters still in the ERROR_WARNING
range of 97-127 inclusive, the state handling code erroneously
reverts back to ERROR_ACTIVE.
Per the CAN standard, only revert to ERROR_ACTIVE when the
error counters are less than 96.
Moreover, in certain Kvaser models, the BUS_ERROR flag is
always set along with undefined bits in the M16C status
register. Thus use bitwise operators instead of full equality
for checking that register against bus errors.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On some x86 laptops, plugging a Kvaser device again after an
unplug makes the firmware always ignore the very first command.
For such a case, provide some room for retries instead of
completely exiting the driver init code.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Send expected argument to the URB completion hander: a CAN
netdevice instead of the network interface private context
`kvaser_usb_net_priv'.
This was discovered by having some garbage in the kernel
log in place of the netdevice names: can0 and can1.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Upon receiving a hardware event with the BUS_RESET flag set,
the driver kills all of its anchored URBs and resets all of
its transmit URB contexts.
Unfortunately it does so under the context of URB completion
handler `kvaser_usb_read_bulk_callback()', which is often
called in an atomic context.
While the device is flooded with many received error packets,
usb_kill_urb() typically sleeps/reschedules till the transfer
request of each killed URB in question completes, leading to
the sleep in atomic bug. [3]
In v2 submission of the original driver patch [1], it was
stated that the URBs kill and tx contexts reset was needed
since we don't receive any tx acknowledgments later and thus
such resources will be locked down forever. Fortunately this
is no longer needed since an earlier bugfix in this patch
series is now applied: all tx URB contexts are reset upon CAN
channel close. [2]
Moreover, a BUS_RESET is now treated _exactly_ like a BUS_OFF
event, which is the recommended handling method advised by
the device manufacturer.
[1] http://article.gmane.org/gmane.linux.network/239442http://www.webcitation.org/6Vr2yagAQ
[2] can: kvaser_usb: Reset all URB tx contexts upon channel close
889b77f7fd
[3] Stacktrace:
<IRQ> [<ffffffff8158de87>] dump_stack+0x45/0x57
[<ffffffff8158b60c>] __schedule_bug+0x41/0x4f
[<ffffffff815904b1>] __schedule+0x5f1/0x700
[<ffffffff8159360a>] ? _raw_spin_unlock_irqrestore+0xa/0x10
[<ffffffff81590684>] schedule+0x24/0x70
[<ffffffff8147d0a5>] usb_kill_urb+0x65/0xa0
[<ffffffff81077970>] ? prepare_to_wait_event+0x110/0x110
[<ffffffff8147d7d8>] usb_kill_anchored_urbs+0x48/0x80
[<ffffffffa01f4028>] kvaser_usb_unlink_tx_urbs+0x18/0x50 [kvaser_usb]
[<ffffffffa01f45d0>] kvaser_usb_rx_error+0xc0/0x400 [kvaser_usb]
[<ffffffff8108b14a>] ? vprintk_default+0x1a/0x20
[<ffffffffa01f5241>] kvaser_usb_read_bulk_callback+0x4c1/0x5f0 [kvaser_usb]
[<ffffffff8147a73e>] __usb_hcd_giveback_urb+0x5e/0xc0
[<ffffffff8147a8a1>] usb_hcd_giveback_urb+0x41/0x110
[<ffffffffa0008748>] finish_urb+0x98/0x180 [ohci_hcd]
[<ffffffff810cd1a7>] ? acct_account_cputime+0x17/0x20
[<ffffffff81069f65>] ? local_clock+0x15/0x30
[<ffffffffa000a36b>] ohci_work+0x1fb/0x5a0 [ohci_hcd]
[<ffffffff814fbb31>] ? process_backlog+0xb1/0x130
[<ffffffffa000cd5b>] ohci_irq+0xeb/0x270 [ohci_hcd]
[<ffffffff81479fc1>] usb_hcd_irq+0x21/0x30
[<ffffffff8108bfd3>] handle_irq_event_percpu+0x43/0x120
[<ffffffff8108c0ed>] handle_irq_event+0x3d/0x60
[<ffffffff8108ec84>] handle_fasteoi_irq+0x74/0x110
[<ffffffff81004dfd>] handle_irq+0x1d/0x30
[<ffffffff81004727>] do_IRQ+0x57/0x100
[<ffffffff8159482a>] common_interrupt+0x6a/0x6a
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
* fix station double-removal when suspending while associating
* fix the HT (802.11n) header length calculation
* fix the CCK radiotap flag used for monitoring, a pretty
old regression but a simple one-liner
* fix per-station group-key handling
-----BEGIN PGP SIGNATURE-----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=DhIp
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2015-01-23' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Another set of last-minute fixes:
* fix station double-removal when suspending while associating
* fix the HT (802.11n) header length calculation
* fix the CCK radiotap flag used for monitoring, a pretty
old regression but a simple one-liner
* fix per-station group-key handling
Signed-off-by: David S. Miller <davem@davemloft.net>
Not caching dst_entries which cause redirects could be exploited by hosts
on the same subnet, causing a severe DoS attack. This effect aggravated
since commit f886497212 ("ipv4: fix dst race in sk_dst_get()").
Lookups causing redirects will be allocated with DST_NOCACHE set which
will force dst_release to free them via RCU. Unfortunately waiting for
RCU grace period just takes too long, we can end up with >1M dst_entries
waiting to be released and the system will run OOM. rcuos threads cannot
catch up under high softirq load.
Attaching the flag to emit a redirect later on to the specific skb allows
us to cache those dst_entries thus reducing the pressure on allocation
and deallocation.
This issue was discovered by Marcelo Leitner.
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Marcelo Leitner <mleitner@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
bpf: fix two bugs
Michael Holzheu caught two issues (in bpf syscall and in the test).
Fix them. Details in corresponding patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
hash map is unordered, so get_next_key() iterator shouldn't
rely on particular order of elements. So relax this test.
Fixes: ffb65f27a1 ("bpf: add a testsuite for eBPF maps")
Reported-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BUG: sleeping function called from invalid context at mm/memory.c:3732
in_atomic(): 0, irqs_disabled(): 0, pid: 671, name: test_maps
1 lock held by test_maps/671:
#0: (rcu_read_lock){......}, at: [<0000000000264190>] map_lookup_elem+0xe8/0x260
Call Trace:
([<0000000000115b7e>] show_trace+0x12e/0x150)
[<0000000000115c40>] show_stack+0xa0/0x100
[<00000000009b163c>] dump_stack+0x74/0xc8
[<000000000017424a>] ___might_sleep+0x23a/0x248
[<00000000002b58e8>] might_fault+0x70/0xe8
[<0000000000264230>] map_lookup_elem+0x188/0x260
[<0000000000264716>] SyS_bpf+0x20e/0x840
Fix it by allocating temporary buffer to store map element value.
Fixes: db20fd2b01 ("bpf: add lookup/update/delete/iterate methods to BPF maps")
Reported-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hitting an INIT collision case during the 4WHS with AUTH enabled, as
already described in detail in commit 1be9a950c6 ("net: sctp: inherit
auth_capable on INIT collisions"), it can happen that we occasionally
still remotely trigger the following panic on server side which seems to
have been uncovered after the fix from commit 1be9a950c6 ...
[ 533.876389] BUG: unable to handle kernel paging request at 00000000ffffffff
[ 533.913657] IP: [<ffffffff811ac385>] __kmalloc+0x95/0x230
[ 533.940559] PGD 5030f2067 PUD 0
[ 533.957104] Oops: 0000 [#1] SMP
[ 533.974283] Modules linked in: sctp mlx4_en [...]
[ 534.939704] Call Trace:
[ 534.951833] [<ffffffff81294e30>] ? crypto_init_shash_ops+0x60/0xf0
[ 534.984213] [<ffffffff81294e30>] crypto_init_shash_ops+0x60/0xf0
[ 535.015025] [<ffffffff8128c8ed>] __crypto_alloc_tfm+0x6d/0x170
[ 535.045661] [<ffffffff8128d12c>] crypto_alloc_base+0x4c/0xb0
[ 535.074593] [<ffffffff8160bd42>] ? _raw_spin_lock_bh+0x12/0x50
[ 535.105239] [<ffffffffa0418c11>] sctp_inet_listen+0x161/0x1e0 [sctp]
[ 535.138606] [<ffffffff814e43bd>] SyS_listen+0x9d/0xb0
[ 535.166848] [<ffffffff816149a9>] system_call_fastpath+0x16/0x1b
... or depending on the the application, for example this one:
[ 1370.026490] BUG: unable to handle kernel paging request at 00000000ffffffff
[ 1370.026506] IP: [<ffffffff811ab455>] kmem_cache_alloc+0x75/0x1d0
[ 1370.054568] PGD 633c94067 PUD 0
[ 1370.070446] Oops: 0000 [#1] SMP
[ 1370.085010] Modules linked in: sctp kvm_amd kvm [...]
[ 1370.963431] Call Trace:
[ 1370.974632] [<ffffffff8120f7cf>] ? SyS_epoll_ctl+0x53f/0x960
[ 1371.000863] [<ffffffff8120f7cf>] SyS_epoll_ctl+0x53f/0x960
[ 1371.027154] [<ffffffff812100d3>] ? anon_inode_getfile+0xd3/0x170
[ 1371.054679] [<ffffffff811e3d67>] ? __alloc_fd+0xa7/0x130
[ 1371.080183] [<ffffffff816149a9>] system_call_fastpath+0x16/0x1b
With slab debugging enabled, we can see that the poison has been overwritten:
[ 669.826368] BUG kmalloc-128 (Tainted: G W ): Poison overwritten
[ 669.826385] INFO: 0xffff880228b32e50-0xffff880228b32e50. First byte 0x6a instead of 0x6b
[ 669.826414] INFO: Allocated in sctp_auth_create_key+0x23/0x50 [sctp] age=3 cpu=0 pid=18494
[ 669.826424] __slab_alloc+0x4bf/0x566
[ 669.826433] __kmalloc+0x280/0x310
[ 669.826453] sctp_auth_create_key+0x23/0x50 [sctp]
[ 669.826471] sctp_auth_asoc_create_secret+0xcb/0x1e0 [sctp]
[ 669.826488] sctp_auth_asoc_init_active_key+0x68/0xa0 [sctp]
[ 669.826505] sctp_do_sm+0x29d/0x17c0 [sctp] [...]
[ 669.826629] INFO: Freed in kzfree+0x31/0x40 age=1 cpu=0 pid=18494
[ 669.826635] __slab_free+0x39/0x2a8
[ 669.826643] kfree+0x1d6/0x230
[ 669.826650] kzfree+0x31/0x40
[ 669.826666] sctp_auth_key_put+0x19/0x20 [sctp]
[ 669.826681] sctp_assoc_update+0x1ee/0x2d0 [sctp]
[ 669.826695] sctp_do_sm+0x674/0x17c0 [sctp]
Since this only triggers in some collision-cases with AUTH, the problem at
heart is that sctp_auth_key_put() on asoc->asoc_shared_key is called twice
when having refcnt 1, once directly in sctp_assoc_update() and yet again
from within sctp_auth_asoc_init_active_key() via sctp_assoc_update() on
the already kzfree'd memory, which is also consistent with the observation
of the poison decrease from 0x6b to 0x6a (note: the overwrite is detected
at a later point in time when poison is checked on new allocation).
Reference counting of auth keys revisited:
Shared keys for AUTH chunks are being stored in endpoints and associations
in endpoint_shared_keys list. On endpoint creation, a null key is being
added; on association creation, all endpoint shared keys are being cached
and thus cloned over to the association. struct sctp_shared_key only holds
a pointer to the actual key bytes, that is, struct sctp_auth_bytes which
keeps track of users internally through refcounting. Naturally, on assoc
or enpoint destruction, sctp_shared_key are being destroyed directly and
the reference on sctp_auth_bytes dropped.
User space can add keys to either list via setsockopt(2) through struct
sctp_authkey and by passing that to sctp_auth_set_key() which replaces or
adds a new auth key. There, sctp_auth_create_key() creates a new sctp_auth_bytes
with refcount 1 and in case of replacement drops the reference on the old
sctp_auth_bytes. A key can be set active from user space through setsockopt()
on the id via sctp_auth_set_active_key(), which iterates through either
endpoint_shared_keys and in case of an assoc, invokes (one of various places)
sctp_auth_asoc_init_active_key().
sctp_auth_asoc_init_active_key() computes the actual secret from local's
and peer's random, hmac and shared key parameters and returns a new key
directly as sctp_auth_bytes, that is asoc->asoc_shared_key, plus drops
the reference if there was a previous one. The secret, which where we
eventually double drop the ref comes from sctp_auth_asoc_set_secret() with
intitial refcount of 1, which also stays unchanged eventually in
sctp_assoc_update(). This key is later being used for crypto layer to
set the key for the hash in crypto_hash_setkey() from sctp_auth_calculate_hmac().
To close the loop: asoc->asoc_shared_key is freshly allocated secret
material and independant of the sctp_shared_key management keeping track
of only shared keys in endpoints and assocs. Hence, also commit 4184b2a79a
("net: sctp: fix memory leak in auth key management") is independant of
this bug here since it concerns a different layer (though same structures
being used eventually). asoc->asoc_shared_key is reference dropped correctly
on assoc destruction in sctp_association_free() and when active keys are
being replaced in sctp_auth_asoc_init_active_key(), it always has a refcount
of 1. Hence, it's freed prematurely in sctp_assoc_update(). Simple fix is
to remove that sctp_auth_key_put() from there which fixes these panics.
Fixes: 730fc3d05c ("[SCTP]: Implete SCTP-AUTH parameter processing")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 69ad0dd7af
Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Date: Mon May 19 13:59:59 2014 -0300
net: mv643xx_eth: Use dma_map_single() to map the skb fragments
caused a nasty regression by removing the support for highmem skb
fragments. By using page_address() to get the address of a fragment's
page, we are assuming a lowmem page. However, such assumption is incorrect,
as fragments can be in highmem pages, resulting in very nasty issues.
This commit fixes this by using the skb_frag_dma_map() helper,
which takes care of mapping the skb fragment properly. Additionally,
the type of mapping is now tracked, so it can be unmapped using
dma_unmap_page or dma_unmap_single when appropriate.
This commit also fixes the error path in txq_init() to release the
resources properly.
Fixes: 69ad0dd7af ("net: mv643xx_eth: Use dma_map_single() to map the skb fragments")
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
Fixes for sh_eth #2
I'm continuing review and testing of Ethernet support on the R-Car H2
chip. This series fixes more of the issues I've found, but it won't be
the last set.
These are not tested on any of the other supported chips.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to stop the RX path accessing the RX ring while it's being
stopped or resized, we clear the interrupt mask (EESIPR) and then call
free_irq() or synchronise_irq(). This is insufficient because the
interrupt handler or NAPI poller may set EESIPR again after we clear
it. Also, in sh_eth_set_ringparam() we currently don't disable NAPI
polling at all.
I could easily trigger a crash by running the loop:
while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done
and 'ping -f' toward the sh_eth port from another machine.
To fix this:
- Add a software flag (irq_enabled) to signal whether interrupts
should be enabled
- In the interrupt handler, if the flag is clear then clear EESIPR
and return
- In the NAPI poller, if the flag is clear then don't set EESIPR
- Set the flag before enabling interrupts in sh_eth_dev_init() and
sh_eth_set_ringparam()
- Clear the flag and serialise with the interrupt and NAPI
handlers before clearing EESIPR in sh_eth_close() and
sh_eth_set_ringparam()
After this, I could run the loop for 100,000 iterations successfully.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device is down then no packet buffers should be allocated.
We also must not touch its registers as it may be powered off.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned. Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.
What's more, sh_eth_tx_timeout() will likely crash if called while
we're resizing the TX ring.
I could easily trigger this by running the loop:
while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an skb to be transmitted is shorter than the minimum Ethernet frame
length, we currently set the DMA descriptor length to the minimum but
do not add zero-padding. This could result in leaking sensitive
data. We also pass different lengths to dma_map_single() and
dma_unmap_single().
Use skb_padto() to pad properly, before calling dma_map_single().
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Dual EMAC, the default VLANs are used to segregate Rx packets between
the ports, so adding the same default VLAN to the switch will affect the
normal packet transfers. So returning error on addition of dual EMAC
default VLANs.
Even if EMAC 0 default port VLAN is added to EMAC 1, it will lead to
break dual EMAC port separations.
Fixes: d9ba8f9e62 (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <stable@vger.kernel.org> # v3.9+
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
Two cls_bpf fixes
Found them while doing a review on act_bpf and going over the
cls_bpf code again. Will also address the first issue in act_bpf
as it needs to be fixed there, too.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating a bpf classifier in tc with priority collisions and
invoking automatic unique handle assignment, cls_bpf_grab_new_handle()
will return a wrong handle id which in fact is non-unique. Usually
altering of specific filters is being addressed over major id, but
in case of collisions we result in a filter chain, where handle ids
address individual cls_bpf_progs inside the classifier.
Issue is, in cls_bpf_grab_new_handle() we probe for head->hgen handle
in cls_bpf_get() and in case we found a free handle, we're supposed
to use exactly head->hgen. In case of insufficient numbers of handles,
we bail out later as handle id 0 is not allowed.
Fixes: 7d1d65cb84 ("net: sched: cls_bpf: add BPF-based classifier")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In cls_bpf_modify_existing(), we read out the number of filter blocks,
do some sanity checks, allocate a block on that size, and copy over the
BPF instruction blob from user space, then pass everything through the
classic BPF checker prior to installation of the classifier.
We should reject mismatches here, there are 2 scenarios: the number of
filter blocks could be smaller than the provided instruction blob, so
we do a partial copy of the BPF program, and thus the instructions will
either be rejected from the verifier or a valid BPF program will be run;
in the other case, we'll end up copying more than we're supposed to,
and most likely the trailing garbage will be rejected by the verifier
as well (i.e. we need to fit instruction pattern, ret {A,K} needs to be
last instruction, load/stores must be correct, etc); in case not, we
would leak memory when dumping back instruction patterns. The code should
have only used nla_len() as Dave noted to avoid this from the beginning.
Anyway, lets fix it by rejecting such load attempts.
Fixes: 7d1d65cb84 ("net: sched: cls_bpf: add BPF-based classifier")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=k63Q
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-3.19-20150121' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-01-21
this is a pull request for v3.19, net/master, which consists of a single patch.
Viktor Babrian fixes the issue in the c_can dirver, that the CAN interface
might continue to send frames after the interface has been shut down.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun says:
====================
s390/qeth patches for net
here are two s390/qeth patches built for net.
One patch is quite large, but we would like to fix the locking warning
seen in recent kernels as soon as possible. But if you want me to submit
these patches for net-next, I will do.
Or Gerlitz says:
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not wait for channel command buffers in IPA commands.
The potential wait could be done while holding a spin lock and causes
in recent kernels such a bug if kernel lock debugging is enabled:
kernel: BUG: sleeping function called from invalid context at drivers/s390/net/qeth_core_main.c:
794
kernel: in_atomic(): 1, irqs_disabled(): 0, pid: 2031, name: NetworkManager
kernel: 2 locks held by NetworkManager/2031:
kernel: #0: (rtnl_mutex){+.+.+.}, at: [<00000000006e0d7a>] rtnetlink_rcv+0x32/0x50
kernel: #1: (_xmit_ETHER){+.....}, at: [<00000000006cfe90>] dev_set_rx_mode+0x30/0x50
kernel: CPU: 0 PID: 2031 Comm: NetworkManager Not tainted 3.18.0-rc5-next-20141124 #1
kernel: 00000000275fb1f0 00000000275fb280 0000000000000002 0000000000000000
00000000275fb320 00000000275fb298 00000000275fb298 00000000007e326a
0000000000000000 000000000099ce2c 00000000009b4988 000000000000000b
00000000275fb2e0 00000000275fb280 0000000000000000 0000000000000000
0000000000000000 00000000001129c8 00000000275fb280 00000000275fb2e0
kernel: Call Trace:
kernel: ([<00000000001128b0>] show_trace+0xf8/0x158)
kernel: [<000000000011297a>] show_stack+0x6a/0xe8
kernel: [<00000000007e995a>] dump_stack+0x82/0xb0
kernel: [<000000000017d668>] ___might_sleep+0x170/0x228
kernel: [<000003ff80026f0e>] qeth_wait_for_buffer+0x36/0xd0 [qeth]
kernel: [<000003ff80026fe2>] qeth_get_ipacmd_buffer+0x3a/0xc0 [qeth]
kernel: [<000003ff80105078>] qeth_l3_send_setdelmc+0x58/0xf8 [qeth_l3]
kernel: [<000003ff8010b1fe>] qeth_l3_set_ip_addr_list+0x2c6/0x848 [qeth_l3]
kernel: [<000003ff8010bbb4>] qeth_l3_set_multicast_list+0x434/0xc48 [qeth_l3]
kernel: [<00000000006cfe9a>] dev_set_rx_mode+0x3a/0x50
kernel: [<00000000006cff90>] __dev_open+0xe0/0x140
kernel: [<00000000006d02a0>] __dev_change_flags+0xa0/0x178
kernel: [<00000000006d03a8>] dev_change_flags+0x30/0x70
kernel: [<00000000006e14ee>] do_setlink+0x346/0x9a0
...
The device driver has plenty of command buffers available
per channel for channel command communication.
In the extremely rare case when there is no command buffer
available, return a NULL pointer and issue a warning
in the kernel log. The caller handles the case when
a NULL pointer is encountered and returns an error.
In the case the wait for command buffer is possible
(because no lock is held as in the OSN case), still wait
until a channel command buffer is available.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Reviewed-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the functions that are registering and unregistering MAC
addresses in the qeth-handled hardware, remove callback functions
that are unnesessary, as only the return code is analyzed.
Translate hardware response codes to semi-standard 'errno'-like
codes for readability.
Add kernel-doc description to the internal API function
qeth_send_control_data().
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Reviewed-by: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In my last commit (a3c00e4: ipv6: Remove BACKTRACK macro), the changes in
__ip6_route_redirect is incorrect. The following case is missed:
1. The for loop tries to find a valid gateway rt. If it fails to find
one, rt will be NULL.
2. When rt is NULL, it is set to the ip6_null_entry.
3. The newly added 'else if', from a3c00e4, will stop the backtrack from
happening.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When registering a mdio bus, Linux assumes than every port has a PHY and tries
to scan it. If a switch port has no PHY registered, DSA will fail to register
the slave MII bus. To fix this, set the slave MII bus PHY mask to the switch
PHYs mask.
As an example, if we use a Marvell MV88E6352 (which is a 7-port switch with no
registered PHYs for port 5 and port 6), with the following declared names:
static struct dsa_chip_data switch_cdata = {
[...]
.port_names[0] = "sw0",
.port_names[1] = "sw1",
.port_names[2] = "sw2",
.port_names[3] = "sw3",
.port_names[4] = "sw4",
.port_names[5] = "cpu",
};
DSA will fail to create the switch instance. With the PHY mask set for the
slave MII bus, only the PHY for ports 0-4 will be scanned and the instance will
be successfully created.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip6_route_output() always returns a valid dst pointer unlike in IPv4
case. So the validation has to be different from the IPv4 path. Correcting
that error in this patch.
This was picked up by a static checker with a following warning -
drivers/net/ipvlan/ipvlan_core.c:380 ipvlan_process_v6_outbound()
warn: 'dst' isn't an ERR_PTR
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timeout entries are sizeof(int) rather than sizeof(long), which
means that when they were getting read we'd also leak kernel memory
to userspace along with the timeout values.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAPI poll logic now enforces that a poller returns exactly the budget
when it wants to be called again.
If a driver limits TX completion, it has to return budget as well when
the limit is hit, not the number of received packets.
Reported-and-tested-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: d75b1ade56 ("net: less interrupt masking in NAPI")
Cc: Manish Chopra <manish.chopra@qlogic.com>
Acked-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the commit d75b1ade56 ("net: less interrupt masking in NAPI") napi repoll
is done only when work_done == budget. When we are in busy_poll we return 0 in
napi_poll. We should return budget.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix an IRQ storm caused by commit 872b5d814f
iwlwifi:
* A fix for scan that fixes a firmware assertion
* A fix that improves roaming behavior. Same fix has been tested for
a while in iwldvm. This is a bit of a work around, but the real fix
should be in mac80211 and will come later.
* A fix for BARs that avoids a WARNING.
* one fix for rfkill while scheduled scan is running.
Linus's system hit this issue. WiFi would be unavailable
after this has happpened because of bad state in cfg80211.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUvhf2AAoJEG4XJFUm622blNIH/3JlfJZxjfFs5nCkLPRS03m1
GNMhwHuoFDUSHNUCO57kROVcoryvd3D9kNA5bDGXkNHQIS1DQj4K44mZFKfF6L1K
Kon/OP+pxJXpDV+5G42zF5QSRLg6uGb/cvxKEXyU9MhISXcWIIyncqAwZZWzoaFS
ZcjqhvO0iUbdywrbU8nAAOH8+8zwL16A5nZxadeBF6yMf939EUsDzcDW9WoSNSsE
vYZlHTRsymx2TANquoFBo8/mSeB0jcd+1eBr6mMetzUJLfjvxihbyP9Ci+C31ov4
592s9dGQpxgri/qbRMt0XjwxAXRYnXluu2Rcf4jmmilQON7cZiZKZQnukpgIu3I=
=cq2e
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2015-01-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
ath9k:
* fix an IRQ storm caused by commit 872b5d814f
iwlwifi:
* A fix for scan that fixes a firmware assertion
* A fix that improves roaming behavior. Same fix has been tested for
a while in iwldvm. This is a bit of a work around, but the real fix
should be in mac80211 and will come later.
* A fix for BARs that avoids a WARNING.
* one fix for rfkill while scheduled scan is running.
Linus's system hit this issue. WiFi would be unavailable
after this has happpened because of bad state in cfg80211.
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit (3d125f9c91) cause i.MX6SX sdb enet cannot work. The cause is
the commit add mdio node with un-correct phy address.
The patch just correct i.MX6sx sdb board enet phy address.
V2:
* As Shawn's suggestion that unit-address should match 'reg' property, so
update ethernet-phy unit-address.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updated hardware documention shows the Rx flow control settings were
moved from the Rx queue operation mode register to a new Rx queue flow
control register. The old flow control settings are now reserved areas
of the Rx queue operation mode register. Update the code to use the new
register.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case userspace attempts to obtain key information for or delete a
unicast key, this is currently erroneously rejected unless the driver
sets the WIPHY_FLAG_IBSS_RSN flag. Apparently enough drivers do so it
was never noticed.
Fix that, and while at it fix a potential memory leak: the error path
in the get_key() function was placed after allocating a message but
didn't free it - move it to a better place. Luckily admin permissions
are needed to call this operation.
Cc: stable@vger.kernel.org
Fixes: e31b82136d ("cfg80211/mac80211: allow per-station GTKs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix a regression introduced by commit a5e70697d0 ("mac80211: add radiotap flag
and handling for 5/10 MHz") where the IEEE80211_CHAN_CCK channel type flag was
incorrectly replaced by the IEEE80211_CHAN_OFDM flag. This commit fixes that by
using the CCK flag again.
Cc: stable@vger.kernel.org
Fixes: a5e70697d0 ("mac80211: add radiotap flag and handling for 5/10 MHz")
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
HT Control field may also be present in management frames, as defined
in 8.2.4.1.10 of 802.11-2012. Account for this in calculation of header
length.
Signed-off-by: Fred Chou <fred.chou.nd@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In normal cases (i.e. when we are fully associated), cfg80211 takes
care of removing all the stations before calling suspend in mac80211.
But in the corner case when we suspend during authentication or
association, mac80211 needs to roll back the station states. But we
shouldn't roll back the station states in the suspend function,
because this is taken care of in other parts of the code, except for
WDS interfaces. For AP types of interfaces, cfg80211 takes care of
disconnecting all stations before calling the driver's suspend code.
For station interfaces, this is done in the quiesce code.
For WDS interfaces we still need to do it here, so move the code into
a new switch case for WDS.
Cc: stable@kernel.org [3.15+]
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Put controller into init mode in network stop to end pending transmissions. The
issue is observed in cases when transmitted frame is not acked.
Signed-off-by: Viktor Babrian <babrian.viktor@renyi.mta.hu>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
- Fix two deadlocks around the pin control mutexes,
a long-standing issue that manifest itself in
plug/unplug of pin controllers. (Tagged for stable.)
- Handle an error path with zero functions in the
Qualcomm pin controller.
- Drop a bogus second GPIO chip added in the Lantiq
driver.
- Fix sudden IRQ loss on Rockchip pin controllers.
- Register the GIT tree in MAINTAINERS.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YGym
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here is a (hopefully final) slew of pin control fixes for the v3.19
series. The deadlock fix is kind of serious and tagged for stable,
the rest is business as usual.
- Fix two deadlocks around the pin control mutexes, a long-standing
issue that manifest itself in plug/unplug of pin controllers.
(Tagged for stable.)
- Handle an error path with zero functions in the Qualcomm pin
controller.
- Drop a bogus second GPIO chip added in the Lantiq driver.
- Fix sudden IRQ loss on Rockchip pin controllers.
- Register the GIT tree in MAINTAINERS"
* tag 'pinctrl-v3.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: MAINTAINERS: add git tree reference
pinctrl: qcom: Don't iterate past end of function array
pinctrl: lantiq: remove bogus of_gpio_chip_add
pinctrl: Fix two deadlocks
pinctrl: rockchip: Avoid losing interrupts when supporting both edges
Pull networking fixes from David Miller:
1) Socket addresses returned in the error queue need to be fully
initialized before being passed on to userspace, fix from Willem de
Bruijn.
2) Interrupt handling fixes to davinci_emac driver from Tony Lindgren.
3) Fix races between receive packet steering and cpu hotplug, from Eric
Dumazet.
4) Allowing netlink sockets to subscribe to unknown multicast groups
leads to crashes, don't allow it. From Johannes Berg.
5) One to many socket races in SCTP fixed by Daniel Borkmann.
6) Put in a guard against the mis-use of ipv6 atomic fragments, from
Hagen Paul Pfeifer.
7) Fix promisc mode and ethtool crashes in sh_eth driver, from Ben
Hutchings.
8) NULL deref and double kfree fix in sxgbe driver from Girish K.S and
Byungho An.
9) cfg80211 deadlock fix from Arik Nemtsov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
s2io: use snprintf() as a safety feature
r8152: remove sram_read
r8152: remove generic_ocp_read before writing
bgmac: activate irqs only if there is nothing to poll
bgmac: register napi before the device
sh_eth: Fix ethtool operation crash when net device is down
sh_eth: Fix promiscuous mode on chips without TSU
ipv6: stop sending PTB packets for MTU < 1280
net: sctp: fix race for one-to-many sockets in sendmsg's auto associate
genetlink: synchronize socket closing and family removal
genetlink: disallow subscribing to unknown mcast groups
genetlink: document parallel_ops
net: rps: fix cpu unplug
net: davinci_emac: Add support for emac on dm816x
net: davinci_emac: Fix ioremap for devices with MDIO within the EMAC address space
net: davinci_emac: Fix incomplete code for getting the phy from device tree
net: davinci_emac: Free clock after checking the frequency
net: davinci_emac: Fix runtime pm calls for davinci_emac
net: davinci_emac: Fix hangs with interrupts
ip: zero sockaddr returned on error queue
...
Pull crypto fix from Herbert Xu:
"This fixes a regression that arose from the change to add a crypto
prefix to module names which was done to prevent the loading of
arbitrary modules through the Crypto API.
In particular, a number of modules were missing the crypto prefix
which meant that they could no longer be autoloaded"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: add missing crypto module aliases
"sp->desc[i]" has 25 characters. "dev->name" has 15 characters. If we
used all 15 characters then the sprintf() would overflow.
I changed the "sprintf(sp->name, "%s Neterion %s"" to snprintf(), as
well, even though it can't overflow just to be consistent.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
