IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Currently this simple setup with DSA:
ip link add br0 type bridge vlan_filtering 1
ip link add bond0 type bond
ip link set bond0 master br0
ip link set swp0 master bond0
will not work because the bridge has created the PVID in br_add_if ->
nbp_vlan_init, and it has notified switchdev of the existence of VLAN 1,
but that was too early, since swp0 was not yet a lower of bond0, so it
had no reason to act upon that notification.
We need a helper in the bridge to replay the switchdev VLAN objects that
were notified since the bridge port creation, because some of them may
have been missed.
As opposed to the br_mdb_replay function, the vg->vlan_list write side
protection is offered by the rtnl_mutex which is sleepable, so we don't
need to queue up the objects in atomic context, we can replay them right
away.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a switchdev port starts offloading a LAG that is already in a
bridge and has an FDB entry pointing to it:
ip link set bond0 master br0
bridge fdb add dev bond0 00:01:02:03:04:05 master static
ip link set swp0 master bond0
the switchdev driver will have no idea that this FDB entry is there,
because it missed the switchdev event emitted at its creation.
Ido Schimmel pointed this out during a discussion about challenges with
switchdev offloading of stacked interfaces between the physical port and
the bridge, and recommended to just catch that condition and deny the
CHANGEUPPER event:
https://lore.kernel.org/netdev/20210210105949.GB287766@shredder.lan/
But in fact, we might need to deal with the hard thing anyway, which is
to replay all FDB addresses relevant to this port, because it isn't just
static FDB entries, but also local addresses (ones that are not
forwarded but terminated by the bridge). There, we can't just say 'oh
yeah, there was an upper already so I'm not joining that'.
So, similar to the logic for replaying MDB entries, add a function that
must be called by individual switchdev drivers and replays local FDB
entries as well as ones pointing towards a bridge port. This time, we
use the atomic switchdev notifier block, since that's what FDB entries
expect for some reason.
Reported-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have a system with DSA ports, and udhcpcd is configured to bring
interfaces up as soon as they are created.
I create a bridge as follows:
ip link add br0 type bridge
As soon as I create the bridge and udhcpcd brings it up, I also have
avahi which automatically starts sending IPv6 packets to advertise some
local services, and because of that, the br0 bridge joins the following
IPv6 groups due to the code path detailed below:
33:33:ff:6d:c1:9c vid 0
33:33:00:00:00:6a vid 0
33:33:00:00:00:fb vid 0
br_dev_xmit
-> br_multicast_rcv
-> br_ip6_multicast_add_group
-> __br_multicast_add_group
-> br_multicast_host_join
-> br_mdb_notify
This is all fine, but inside br_mdb_notify we have br_mdb_switchdev_host
hooked up, and switchdev will attempt to offload the host joined groups
to an empty list of ports. Of course nobody offloads them.
Then when we add a port to br0:
ip link set swp0 master br0
the bridge doesn't replay the host-joined MDB entries from br_add_if,
and eventually the host joined addresses expire, and a switchdev
notification for deleting it is emitted, but surprise, the original
addition was already completely missed.
The strategy to address this problem is to replay the MDB entries (both
the port ones and the host joined ones) when the new port joins the
bridge, similar to what vxlan_fdb_replay does (in that case, its FDB can
be populated and only then attached to a bridge that you offload).
However there are 2 possibilities: the addresses can be 'pushed' by the
bridge into the port, or the port can 'pull' them from the bridge.
Considering that in the general case, the new port can be really late to
the party, and there may have been many other switchdev ports that
already received the initial notification, we would like to avoid
delivering duplicate events to them, since they might misbehave. And
currently, the bridge calls the entire switchdev notifier chain, whereas
for replaying it should just call the notifier block of the new guy.
But the bridge doesn't know what is the new guy's notifier block, it
just knows where the switchdev notifier chain is. So for simplification,
we make this a driver-initiated pull for now, and the notifier block is
passed as an argument.
To emulate the calling context for mdb objects (deferred and put on the
blocking notifier chain), we must iterate under RCU protection through
the bridge's mdb entries, queue them, and only call them once we're out
of the RCU read-side critical section.
There was some opportunity for reuse between br_mdb_switchdev_host_port,
br_mdb_notify and the newly added br_mdb_queue_one in how the switchdev
mdb object is created, so a helper was created.
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SWITCHDEV_ATTR_ID_BRIDGE_AGEING_TIME attribute is only emitted from:
sysfs/ioctl/netlink
-> br_set_ageing_time
-> __set_ageing_time
therefore not at bridge port creation time, so:
(a) switchdev drivers have to hardcode the initial value for the address
ageing time, because they didn't get any notification
(b) that hardcoded value can be out of sync, if the user changes the
ageing time before enslaving the port to the bridge
We need a helper in the bridge, such that switchdev drivers can query
the current value of the bridge ageing time when they start offloading
it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It may happen that we have the following topology with DSA or any other
switchdev driver with LAG offload:
ip link add br0 type bridge stp_state 1
ip link add bond0 type bond
ip link set bond0 master br0
ip link set swp0 master bond0
ip link set swp1 master bond0
STP decides that it should put bond0 into the BLOCKING state, and
that's that. The ports that are actively listening for the switchdev
port attributes emitted for the bond0 bridge port (because they are
offloading it) and have the honor of seeing that switchdev port
attribute can react to it, so we can program swp0 and swp1 into the
BLOCKING state.
But if then we do:
ip link set swp2 master bond0
then as far as the bridge is concerned, nothing has changed: it still
has one bridge port. But this new bridge port will not see any STP state
change notification and will remain FORWARDING, which is how the
standalone code leaves it in.
We need a function in the bridge driver which retrieves the current STP
state, such that drivers can synchronize to it when they may have missed
switchdev events.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem:
The "lapb_t1timer_running" function in "lapb_timer.c" is used in only
one place: in the "lapb_kick" function in "lapb_out.c". "lapb_kick" calls
"lapb_t1timer_running" to check if the timer is already pending, and if
it is not, schedule it to run.
However, if the timer has already fired and is running, and is waiting to
get the "lapb->lock" lock, "lapb_t1timer_running" will not detect this,
and "lapb_kick" will then schedule a new timer. The old timer will then
abort when it sees a new timer pending.
I think this is not right. The purpose of "lapb_kick" should be ensuring
that the actual work of the timer function is scheduled to be done.
If the timer function is already running but waiting for the lock,
"lapb_kick" should not abort and reschedule it.
Changes made:
I added a new field "t1timer_running" in "struct lapb_cb" for
"lapb_t1timer_running" to use. "t1timer_running" will accurately reflect
whether the actual work of the timer is pending. If the timer has fired
but is still waiting for the lock, "t1timer_running" will still correctly
reflect whether the actual work is waiting to be done.
The old "t1timer_stop" field, whose only responsibility is to ask a timer
(that is already running but waiting for the lock) to abort, is no longer
needed, because the new "t1timer_running" field can fully take over its
responsibility. Therefore "t1timer_stop" is deleted.
"t1timer_running" is not simply a negation of the old "t1timer_stop".
At the end of the timer function, if it does not reschedule itself,
"t1timer_running" is set to false to indicate that the timer is stopped.
For consistency of the code, I also added "t2timer_running" and deleted
"t2timer_stop".
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the driver name, ASIC ID and the switch name via devlink. This is a
useful information for user space tooling.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following batch contains Netfilter updates for net-next:
1) Split flowtable workqueues per events, from Oz Shlomo.
2) fall-through warnings for clang, from Gustavo A. R. Silva
3) Remove unused declaration in conntrack, from YueHaibing.
4) Consolidate skb_try_make_writable() in flowtable datapath,
simplify some of the existing codebase.
5) Call dst_check() to fall back to static classic forwarding path.
6) Update table flags from commit phase.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding CONFIG_PCPU_DEV_REFCNT, I forgot that the
initial net device refcount was 0.
When CONFIG_PCPU_DEV_REFCNT is not set, this means
the first dev_hold() triggers an illegal refcount
operation (addition on 0)
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 0 PID: 1 at lib/refcount.c:25 refcount_warn_saturate+0x128/0x1a4
Fix is to change initial (and final) refcount to be 1.
Also add a missing kerneldoc piece, as reported by
Stephen Rothwell.
Fixes: 919067cc845f ("net: add CONFIG_PCPU_DEV_REFCNT")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Guenter Roeck <groeck@google.com>
Tested-by: Guenter Roeck <groeck@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei says:
====================
dpaa2-switch: offload bridge port flags to device
Add support for offloading bridge port flags to the switch. With this
patch set, the learning, broadcast flooding and unknown ucast/mcast
flooding states will be user configurable.
Apart from that, the last patch is a small fix that configures the
offload_fwd_mark if the switch port is under a bridge or not.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If a switch port is under a bridge, the offload_fwd_mark should be setup
before sending the skb towards the stack so that the bridge does not try
to flood the packet on the other switch ports.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring per port unknown flooding by accepting both
BR_FLOOD and BR_MCAST_FLOOD as offloadable bridge port flags.
The DPAA2 switch does not support at the moment configuration of unknown
multicast flooding independently of unknown unicast flooding, therefore
check that both BR_FLOOD and BR_MCAST_FLOOD have the same state.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BR_BCAST_FLOOD bridge port flag is now accepted by the driver and a
change in its state will determine a reconfiguration of the broadcast
egress flooding list on the FDB associated with the port.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring the learning state of a switch port.
When the user requests the HW learning to be disabled, a fast-age
procedure on that specific port is run so that previously learnt
addresses do not linger.
At device probe as well as on a bridge leave action, the ports are
configured with HW learning disabled since they are basically a
standalone port.
At the same time, at bridge join we inherit the bridge port BR_LEARNING
flag state and configure it on the switch port.
There were already some MC firmware ABI functions for changing the
learning state, but those were per FDB (bridging domain) and not per
port so we need to adjust those to use the new MC fw command which is
per port.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the code that determines the list of egress flood interfaces for
a specific flood type into a new function -
dpaa2_switch_fdb_get_flood_cfg().
This will help us to not duplicate code when the broadcast and
unknown ucast/mcast flooding domains will be individually configurable.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid a forward declaration in the next patches, move the
dpaa2_switch_fdb_set_egress_flood() function to the top of the file.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aleksander Jan Bajkowski says:
====================
net: dsa: lantiq: add support for xRX300 and xRX330
Changed since v3:
* fixed last compilation warning
Changed since v2:
* fixed compilation warnings
* removed example bindings for xrx330
* patches has been refactored due to upstream changes
Changed since v1:
* gswip_mii_mask_cfg() can now change port 3 on xRX330
* changed alowed modes on port 0 and 5 for xRX300 and xRX330
* moved common part of phylink validation into gswip_phylink_set_capab()
* verify the compatible string against the hardware
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add compatible string for xRX300 and xRX330 SoCs.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify compatible string against hardware.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to use all PHYs on GRX300 and GRX330. The ARX300
has 3 and the GRX330 has 4 integrated PHYs connected to different
ports compared to VRX200. Each integrated PHY can work as single
Gigabit Ethernet PHY (GMII) or as double Fast Ethernet PHY (MII).
Allowed port configurations:
xRX200:
GMAC0: RGMII, MII, REVMII or RMII port
GMAC1: RGMII, MII, REVMII or RMII port
GMAC2: GPHY0 (GMII)
GMAC3: GPHY0 (MII)
GMAC4: GPHY1 (GMII)
GMAC5: GPHY1 (MII) or RGMII port
xRX300:
GMAC0: RGMII port
GMAC1: GPHY2 (GMII)
GMAC2: GPHY0 (GMII)
GMAC3: GPHY0 (MII)
GMAC4: GPHY1 (GMII)
GMAC5: GPHY1 (MII) or RGMII port
xRX330:
GMAC0: RGMII, GMII or RMII port
GMAC1: GPHY2 (GMII)
GMAC2: GPHY0 (GMII)
GMAC3: GPHY0 (MII) or GPHY3 (GMII)
GMAC4: GPHY1 (GMII)
GMAC5: GPHY1 (MII), RGMII or RMII port
Tested on D-Link DWR966 (xRX330) with OpenWRT.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-03-22
This series contains updates to ice and iavf drivers.
Haiyue Wang says:
The Intel E810 Series supports a programmable pipeline for a domain
specific protocols classification, for example GTP by Dynamic Device
Personalization (DDP) profile.
The E810 PF has introduced flex-bytes support by ethtool user-def option
allowing for packet deeper matching based on an offset and value for DDP
usage.
For making VF also benefit from this flexible protocol classification,
some new virtchnl messages are defined and handled by PF, so VF can
query this new flow director capability, and use ethtool with extending
the user-def option to configure Rx flow classification.
The new user-def 0xAAAABBBBCCCCDDDD: BBBB is the 2 byte pattern while
AAAA corresponds to its offset in the packet. Similarly DDDD is the 2
byte pattern with CCCC being the corresponding offset. The offset ranges
from 0x0 to 0x1F7 (up to 504 bytes into the packet). The offset starts
from the beginning of the packet.
This feature can be used to allow customers to set flow director rules
for protocols headers that are beyond standard ones supported by
ethtool (e.g. PFCP or GTP-U).
Like for matching GTP-U's TEID value 0x10203040:
ethtool -N ens787f0v0 flow-type udp4 dst-port 2152 \
user-def 0x002e102000303040 action 13
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Preparations for resilient nexthop groups
This patchset contains preparations for resilient nexthop groups support in
mlxsw. A follow-up patchset will add support and selftests. Most of the
patches are trivial and small to make review easier.
Patchset overview:
Patch #1 removes RTNL assertion in nexthop notifier block since it is
not needed. The assertion will trigger when mlxsw starts processing
notifications related to resilient groups as not all are emitted with
RTNL held.
Patches #2-#9 gradually add support for nexthops with trap action. Up
until now mlxsw did not program nexthops whose neighbour entry was not
resolved. This will not work with resilient groups as their size is
fixed and the nexthop mapped to each bucket is determined by the nexthop
code. Therefore, nexthops whose neighbour entry is not resolved will be
programmed to trap packets to the CPU in order to trigger neighbour
resolution.
Patch #10 is a non-functional change to allow for code reuse between
regular nexthop groups and resilient ones.
Patch #11 avoids unnecessary neighbour updates in hardware. See the
commit message for a detailed explanation.
Patches #12-#14 add support for additional nexthop group sizes that are
supported by Spectrum-{2,3} ASICs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-{2,3} support different adjacency group size ranges compared to
Spectrum-1. Add an array describing these ranges and change the common
code to use the array which was set during the per-ASIC initialization.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device supports a fixed set of adjacency group sizes. Encode these
sizes in an array, so that the next patch will be able to split it
between Spectrum-1 and Spectrum-{2,3}, which support different size
ranges.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several differences in the router module between Spectrum-1
and Spectrum-{2,3}. Currently, this is only apparent in the router
interface (RIF) operations that are split between these ASICs.
A subsequent patch is going to introduce another difference between
these ASICs.
Create per-ASIC router operations that will encapsulate all these
differences. For now, these operations are only used to set the per-ASIC
RIF operations in 'mlxsw_sp->router->rif_ops_arr'. Note that this fields
was unused since commit 1f5b23033937 ("mlxsw: spectrum: Set RIF ops per
ASIC type").
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid updating neighbour and adjacency entries in hardware when the
neighbour is already connected and its MAC address did not change. This
can happen, for example, when neighbour transitions between valid states
such as 'NUD_REACHABLE' and 'NUD_DELAY'.
This is especially important for resilient hashing as these updates will
result in adjacency entries being marked as active.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The validation of a nexthop group entry is also necessary for resilient
nexthop groups, so break the validation to a separate function to allow
for code reuse in subsequent patches.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Encapsulate this functionality in a separate function, so that it could
be invoked by follow-up patches, when replacing a nexthop bucket that is
part of a resilient nexthop group.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw_sp_nexthop_update() is used to update the configuration of
Ethernet-type nexthops, as opposed to mlxsw_sp_nexthop_ipip_update(),
which is used to update IPinIP-type nexthops.
Rename the function to mlxsw_sp_nexthop_eth_update(), so that it is
consistent with mlxsw_sp_nexthop_ipip_update().
It will allow us to introduce mlxsw_sp_nexthop_update() in a follow-up
patch, which calls either of above mentioned function based on the
nexthop's type.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, nexthops are programmed with either forward or discard action
(for blackhole nexthops). Nexthops that do not have a valid MAC address
(neighbour) or router interface (RIF) are simply not written to the
adjacency table.
In resilient nexthop groups, the size of the group must remain fixed and
the kernel is in complete control of the layout of the adjacency table.
A nexthop without a valid MAC or RIF will therefore be written with a
trap action, to trigger neighbour resolution.
Allow such nexthops to be programmed to the adjacency table to enable
above mentioned use case.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nexthops that need to be programmed with a trap action might not have a
valid router interface (RIF) associated with them. Therefore, use the
loopback RIF created during initialization to program them to the
device.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the action associated with the nexthop is assumed to be
'forward' unless the 'discard' bit is set.
Instead, simplify this by introducing a dedicated field to represent the
action of the nexthop. This will allow us to more easily introduce more
actions, such as trap.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comments assume that nexthops are simple Ethernet nexthops
that are programmed to forward packets to the associated neighbour. This
is no longer the case, as both IPinIP and blackhole nexthops are now
supported.
Adjust the comments to reflect these changes.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The helper returns the MAC address associated with the nexthop. It is
only valid when the nexthop forwards packets and when it is an Ethernet
nexthop. Reflect this in the checks the helper is performing.
This is not an issue because the sole caller of the function only
invokes it for such nexthops.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The helper mlxsw_sp_nexthop_offload() is actually interested in finding
out if the nexthop is both written to the adjacency table and forwarding
packets (as opposed to discarding them).
Rename it to mlxsw_sp_nexthop_is_forward() and remove
mlxsw_sp_nexthop_is_discard().
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the RTNL assertion in the nexthop notifier block. The assertion
is not needed given RTNL is never assumed to be taken.
This is a preparation for future patches where mlxsw will start handling
nexthop events that are not always sent with RTNL held.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently we had an interop issue where RARP packets got suppressed with
bridge neigh suppression enabled, but the check in the code was meant to
suppress GARP. Exclude RARP packets from it which would allow some VMWare
setups to work, to quote the report:
"Those RARP packets usually get generated by vMware to notify physical
switches when vMotion occurs. vMware may use random sip/tip or just use
sip=tip=0. So the RARP packet sometimes get properly flooded by the vtep
and other times get dropped by the logic"
Reported-by: Amer Abdalamer <amer@nvidia.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xps_queue_show is mostly made of an RCU read-side critical section and
calls bitmap_zalloc with GFP_KERNEL in the middle of it. That is not
allowed as this call may sleep and such behaviours aren't allowed in RCU
read-side critical sections. Fix this by using GFP_NOWAIT instead.
Fixes: 5478fcd0f483 ("net: embed nr_ids in the xps maps")
Reported-by: kernel test robot <oliver.sang@intel.com>
Suggested-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the CONFIG_PM_SLEEP ifdefery to fix the build error
and use __maybe_unused for the suspend()/resume() hooks to avoid
build warning:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:769:21:
error: 'stmmac_runtime_suspend' undeclared here (not in a function); did you mean 'stmmac_suspend'?
769 | SET_RUNTIME_PM_OPS(stmmac_runtime_suspend, stmmac_runtime_resume, NULL)
| ^~~~~~~~~~~~~~~~~~~~~~
./include/linux/pm.h:342:21: note: in definition of macro 'SET_RUNTIME_PM_OPS'
342 | .runtime_suspend = suspend_fn, \
| ^~~~~~~~~~
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:769:45:
error: 'stmmac_runtime_resume' undeclared here (not in a function)
769 | SET_RUNTIME_PM_OPS(stmmac_runtime_suspend, stmmac_runtime_resume, NULL)
| ^~~~~~~~~~~~~~~~~~~~~
./include/linux/pm.h:343:20: note: in definition of macro 'SET_RUNTIME_PM_OPS'
343 | .runtime_resume = resume_fn, \
| ^~~~~~~~~
Fixes: 5ec55823438e ("net: stmmac: add clocks management for gmac driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
s/verifed/verified/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc warns about a pointless condition:
drivers/isdn/hardware/mISDN/hfcmulti.c: In function 'hfcmulti_interrupt':
drivers/isdn/hardware/mISDN/hfcmulti.c:2752:17: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
2752 | ; /* external IRQ */
As the check has no effect, just remove it.
Suggested-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ptype_all and ptype_base are declared in net/core/dev.c as non-static,
because they are used by net-procfs.c too. However, a "make W=1" build
complains that there was no previous declaration of ptype_all and
ptype_base in a header file, so this way of declaring things constitutes
a violation of coding style.
Let's move the extern declarations of ptype_all and ptype_base to the
linux/netdevice.h file, which is included by net-procfs.c too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since their introduction in commit 04157469b7b8 ("net: Use static_key
for XPS maps"), xps_needed and xps_rxqs_needed were never used outside
net/core/dev.c, so I don't really understand why they were exported as
symbols in the first place.
This is needed in order to silence a "make W=1" warning about these
static keys not being declared as static variables, but not having a
previous declaration in a header file nonetheless.
Cc: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only caller of br_vlan_tunnel_lookup, br_handle_ingress_vlan_tunnel,
extracts the tunnel_id from struct ip_tunnel_info::struct ip_tunnel_key::
tun_id which is a __be64 value.
The exact endianness does not seem to matter, because the tunnel id is
just used as a lookup key for the VLAN group's tunnel hash table, and
the value is not interpreted directly per se. Moreover,
rhashtable_lookup_fast treats the key argument as a const void *.
Therefore, there is no functional change associated with this patch,
just one to silence "make W=1" builds.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warnings:
./drivers/net/ethernet/chelsio/cxgb4/cudbg_lib.c:3540:2-8: WARNING: NULL
check before some freeing functions is not needed.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0b5294483c35 ("net: dsa: mv88e6xxx: scratch: Fixup kerneldoc")
has addressed some but not all kerneldoc warnings for the Global 2
Scratch register accessors. Namely, we have some mismatches between
the function names in the kerneldoc and the ones in the actual code.
Let's adjust the comments so that they match the functions they're
sitting next to.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Error recovery improvements.
This series contains some improvements for error recovery. The main
changes are:
1. Keep better track of the health register mappings with the
"status_reliable" flag.
2. Don't wait for firmware responses if firmware is not healthy.
3. Better retry logic of the first firmware message.
4. Set the proper flag early to let the RDMA driver know that firmware
reset has been detected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Two enhancements:
1. Read the health status first before sending the first
HWRM_VER_GET message to firmware instead of the other way around.
This guarantees we got the accurate health status before we attempt
to send the message.
2. We currently only retry sending the first HWRM_VER_GET message to
the firmware if the firmware is in the process of booting. If the
firmware is in error state and is doing core dump for example, the
driver should also retry if the health register has the RECOVERING
flag set. This flag indicates the firmware will undergo recovery
soon. Modify the retry logic to retry for this case as well.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once the chip goes through reset, the register mapping may be lost
and any read of the mapped health registers may return garbage value
until the registers are mapped again in the init path.
Reading BNXT_FW_RESET_INPROG_REG after firmware reset will likely
return garbage value due to the above reason. Reading this register
is for information purpose only so remove it.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During ifup, if the driver detects that firmware has gone through a
reset, it will go through a re-probe sequence. If the RDMA driver is
loaded, the re-probe sequence includes calling the RDMA driver to stop.
We need to set the BNXT_STATE_FW_RESET_DET flag earlier so that it is
visible to the RDMA driver. The RDMA driver's stop sequence is
different if firmware has gone through a reset.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: P B S Naresh Kumar <nareshkumar.pbs@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
