IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The open delay time has to be applied only on the first sample of the
X/Y coordinates because on the following samples the ADC channel is not
changed. Removing this time from the samples after the first one,
"ti,coordinate-readouts" greater than 1, decreases the total acquisition
time, allowing to increase the number of acquired coordinates in the time
unit.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-4-dariobin@libero.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Z2 step configuration doesn't erase the SEL_INP_SWC_3_0 bit-field
before setting the ADC channel. This way its value could be corrupted by
the ADC channel selected for the Z1 coordinate.
Fixes: 8c896308feae ("input: ti_am335x_adc: use only FIFO0 and clean up a little")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-3-dariobin@libero.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As reported by the STEPCONFIG[1-16] registered field descriptions of the
TI reference manual, for the ADC "in single ended, SEL_INM_SWC_3_0 must
be 1xxx".
Unlike the Y and Z coordinates, this bit has not been set for the step
configuration registers used to sample the X coordinate.
Fixes: 1b8be32e6914 ("Input: add support for TI Touchscreen controller")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-2-dariobin@libero.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some Silead touchscreens have support for an active (battery powered)
pen, add support for this.
So far pen-support has only been seen on X86/ACPI (non devicetree) devs,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new properties are deliberately not added
to the existing silead devicetree-bindings documentation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211122220637.11386-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unfortunately, at the time of writing this commit message, we have been
unable to get permission from Silead, or from device OEMs, to distribute
the necessary Silead firmware files in linux-firmware.
On a whole bunch of devices the UEFI BIOS code contains a touchscreen
driver, which contains an embedded copy of the firmware. The fw-loader
code has a "platform" fallback mechanism, which together with info on the
firmware from drivers/platform/x86/touchscreen_dmi.c will use the firmware
from the UEFI driver when the firmware is missing from /lib/firmware. This
makes the touchscreen work OOTB without users needing to manually download
the firmware.
The firmware bundled with the original Windows/Android is usually newer
then the firmware in the UEFI driver and it is better calibrated. This
better calibration can lead to significant differences in the reported
min/max coordinates.
Add support for a new (optional) "silead,efi-fw-min-max" property which
provides a set of alternative min/max values to use for the x/y axis when
the EFI embedded firmware is used.
The new property is only used on (x86) devices which do not use devicetree,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new property is deliberately not added to the
existing silead devicetree-bindings documentation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211122220637.11386-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2 small fixes for pen support
1. Set the id.vendor field for the pen input_dev
2. Fix a typo in a comment
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211212124242.81019-5-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
goodix_get_gpio_config() errors are fatal (abort probe()) so log them
at KERN_ERR level rather then as debug messages.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211212124242.81019-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmF/AjYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1hkIAJ6sFDbvb4M4LMwf
Slh2NVL9o5sLMBDzVwnVlyMSKDbMn1WBKreGssaLgZjGDc74lxsdSmw5l9MZm0JN
xlq95Q6XFiuu+0qDHPWwfDz3JFO4TqW2ZLLPWk9NnkNbRXqccSrlVRi1RpgE1t3/
NUtS8CQLu6A2BYMc6mkk3aV6IwSNKOkWbM5eBHSvU4j8B6lLbNQop0AfO/wyY1xB
U6LiVE1RpN/b7Yv+75ITtNzuHzVIBx6305FvSnOlKbMKKvIClt96Vd2OeuoEkK+6
wGU8JraB1+fc0GckAhynNrjWQWdvi0MAhFWWEJxjS20OGcV1rXDduNfkVNauO1Zn
+dNyJ3s=
=g9fz
-----END PGP SIGNATURE-----
Merge tag 'v5.15' into next
Sync up with the mainline to get the latest APIs and DT bindings.
When converting a rumble into a periodic effect, for compatibility,
the magnitude is effectively calculated using:
magnitude = max(strong_rubble / 3 + weak_rubble / 6, 0x7fff);
The rumble magnitudes are both u16 and the resulting magnitude is
s16. The max is presumably an attempt to limit the result of the
calculation to the maximum possible magnitude for the s16 result,
and thus should be a min.
However in the case of strong = weak = 0xffff, the result of the first
part of the calculation is 0x7fff, meaning that the min would be
redundant anyway, so simply remove the current max.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211130135039.13726-1-ckeepax@opensource.cirrus.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Don't populate a couple of arrays on the stack but instead make them
static const. Also makes the object code smaller by a few hundred
bytes.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20211129231749.619469-1-colin.i.king@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes: 487358627825 ("Input: iforce - use DMA-safe buffer when getting IDs from USB")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 5.3
Link: https://lore.kernel.org/r/20211025115501.5190-1-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Modern devices may redraw display at 60 Hz, make sure we have one input
sample per one frame. Reduce sample period to 15ms, so we would get up
to 66.6 samples per second, although realistically with all the jitter
and extra scheduling wiggle room, we would end up just above 60 samples
per second. This should be a good compromise between sampling too often
and sampling too seldom.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108114145.84118-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently the ili210x driver implements a threaded interrupt handler which
starts upon edge on the interrupt line, and then polls the touch controller
for samples. Every time a sample is obtained from the controller, the thread
function checks whether further polling is required, and if so, waits fixed
amount of time before polling for next sample.
The delay between consecutive samples can thus vary greatly, because the
I2C transfer required to retrieve the sample from the controller takes
different amount of time on different platforms. Furthermore, different
models of the touch controllers supported by this driver require different
delays during retrieval of samples too.
Instead of waiting fixed amount of time before polling for next sample,
determine how much time passed since the beginning of sampling cycle and
then wait only the remaining amount of time within the sampling cycle.
This makes the driver deliver samples with equal spacing between them.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005216.480525-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ili251x touch controller needs 5ms delay between sending I2C device
address and register address, and, writing or reading register data.
According to downstream ili251x example code, this 5ms delay is not
required when reading touch samples out of the controller. Implement
such a special case.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005259.480545-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some firmwares occasionally report bogus data from trackpoint, with X or Y
displacement being too large (outside of [-127, 127] range). Let's drop such
packets so that we do not generate jumps.
Signed-off-by: Phoenix Huang <phoenix@emc.com.tw>
Tested-by: Yufei Du <yufeidu@cs.unc.edu>
Link: https://lore.kernel.org/r/20210729010940.5752-1-phoenix@emc.com.tw
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The created rmi device is orphan, which breaks the real device
hierarchy, and can cause some trouble, especially during suspend
and resume sequences. E.g. in case of I2C, rmi dev should be child
of the I2C client device.
Fix this, assigning the transport device as parent of the rmi device.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1635514971-18415-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fujitsu Lifebook T725 laptop requires, like a few other similar
models, the nomux and notimeout options to probe the touchpad
properly. This patch adds the corresponding quirk entries.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1191980
Tested-by: Neal Gompa <ngompa13@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20211103070019.13374-1-tiwai@suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to the datasheet "The CAP1206 is pin- and register-compatible
with the CAP1106, with the exception of the GAIN[1:0] bits and ALT_POL
bit"(57). So, this patch aims to disable them as they are no longer
used.
Signed-off-by: Jesse Taube <mr.bossman075@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 83b41248ed04 ("Input: cy8ctmg110_ts - switch to using gpiod API")
remove the last use of <linux/input/cy8ctmg110_pdata.h> but left the header
file behind. Nothing uses it now, delete it.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20211102220203.940290-6-corbet@lwn.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- Fix compilation of callchain related code on powerpc with gcc11+.
- Fix PERF_SAMPLE_WEIGHT_STRUCT support in 'perf script'
- Check session->header.env.arch before using it, fixing a segmentation fault.
- Suppress 'rm dlfilter' build messages.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCYX7NvgAKCRCyPKLppCJ+
J0kmAQCAuh2Pt2eL+KUat/RgHXG+on5EkFfqlHVzebjmTv3/nwD/eyKF5AcgvTfb
DGIntW5QskCeAal05g9Po1+xPdU2aQU=
=3oio
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-fixes-for-v5.15-2021-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Fix compilation of callchain related code on powerpc with gcc11+
- Fix PERF_SAMPLE_WEIGHT_STRUCT support in 'perf script'
- Check session->header.env.arch before using it, fixing a segmentation
fault
- Suppress 'rm dlfilter' build messages
* tag 'perf-tools-fixes-for-v5.15-2021-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf script: Fix PERF_SAMPLE_WEIGHT_STRUCT support
perf callchain: Fix compilation on powerpc with gcc11+
perf script: Check session->header.env.arch before using it
perf build: Suppress 'rm dlfilter' build message
* Fixes for Xen emulator bugs showing up as debug kernel WARNs
* Fix another issue with SEV/ES string I/O VMGEXITs
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmF6uGIUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNRagf/Srvk9lNcRh4cEzsczErKMyr3xOqA
jgsTSqgl1ExJI9sBLMpVYBOFGILMaMSrhLPIltKPy0Bj/E+hw8WOQwPa44QjWlSD
MAUxO1Nryt9Luc2L8uSd1c//g4fr4V1BhOaumk1lM14Q8EDfQBcDIMI2ZKueMU1+
2Q+n8/AsG63jQIINwKNidof0dzRtbfcE30Wq/8QHttIPo5wt6l0YClOlOikqNY8N
5+WSQFmuutHIXftq5Jb/Ldn/+HVukWZyZOEVwLnBpM9uBvIubNgcEakqvxsaVtAn
FHdvnA+Bk99/Xuhl+wRLQo8ofzQIQ13RQv3HPArJAJv34oAJZx2rNObVlA==
=6ofB
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
- Fixes for s390 interrupt delivery
- Fixes for Xen emulator bugs showing up as debug kernel WARNs
- Fix another issue with SEV/ES string I/O VMGEXITs
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Take srcu lock in post_kvm_run_save()
KVM: SEV-ES: fix another issue with string I/O VMGEXITs
KVM: x86/xen: Fix kvm_xen_has_interrupt() sleeping in kvm_vcpu_block()
KVM: x86: switch pvclock_gtod_sync_lock to a raw spinlock
KVM: s390: preserve deliverable_mask in __airqs_kick_single_vcpu
KVM: s390: clear kicked_mask before sleeping again
-F weight in perf script is broken.
# ./perf mem record
# ./perf script -F weight
Samples for 'dummy:HG' event do not have WEIGHT attribute set. Cannot
print 'weight' field.
The sample type, PERF_SAMPLE_WEIGHT_STRUCT, is an alternative of the
PERF_SAMPLE_WEIGHT sample type. They share the same space, weight. The
lower 32 bits are exactly the same for both sample type. The higher 32
bits may be different for different architecture. For a new kernel on
x86, the PERF_SAMPLE_WEIGHT_STRUCT is used. For an old kernel or other
ARCHs, the PERF_SAMPLE_WEIGHT is used.
With -F weight, current perf script will only check the input string
"weight" with the PERF_SAMPLE_WEIGHT sample type. Because the commit
ea8d0ed6eae3 ("perf tools: Support PERF_SAMPLE_WEIGHT_STRUCT") didn't
update the PERF_SAMPLE_WEIGHT_STRUCT sample type for perf script. For a
new kernel on x86, the check fails.
Use PERF_SAMPLE_WEIGHT_TYPE, which supports both sample types, to
replace PERF_SAMPLE_WEIGHT
Fixes: ea8d0ed6eae37b01 ("perf tools: Support PERF_SAMPLE_WEIGHT_STRUCT")
Reported-by: Joe Mario <jmario@redhat.com>
Reviewed-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Tested-by: Joe Mario <jmario@redhat.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Joe Mario <jmario@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Link: https://lore.kernel.org/r/1632929894-102778-1-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Got following build fail on powerpc:
CC arch/powerpc/util/skip-callchain-idx.o
In function ‘check_return_reg’,
inlined from ‘check_return_addr’ at arch/powerpc/util/skip-callchain-idx.c:213:7,
inlined from ‘arch_skip_callchain_idx’ at arch/powerpc/util/skip-callchain-idx.c:265:7:
arch/powerpc/util/skip-callchain-idx.c:54:18: error: ‘dwarf_frame_register’ accessing 96 bytes \
in a region of size 64 [-Werror=stringop-overflow=]
54 | result = dwarf_frame_register(frame, ra_regno, ops_mem, &ops, &nops);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/powerpc/util/skip-callchain-idx.c: In function ‘arch_skip_callchain_idx’:
arch/powerpc/util/skip-callchain-idx.c:54:18: note: referencing argument 3 of type ‘Dwarf_Op *’
In file included from /usr/include/elfutils/libdwfl.h:32,
from arch/powerpc/util/skip-callchain-idx.c:10:
/usr/include/elfutils/libdw.h:1069:12: note: in a call to function ‘dwarf_frame_register’
1069 | extern int dwarf_frame_register (Dwarf_Frame *frame, int regno,
| ^~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
The dwarf_frame_register args changed with [1],
Updating ops_mem accordingly.
[1] https://sourceware.org/git/?p=elfutils.git;a=commit;h=5621fe5443da23112170235dd5cac161e5c75e65
Reviewed-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Mark Wieelard <mjw@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20210928195253.1267023-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When perf.data is not written cleanly, we would like to process existing
data as much as possible (please see f_header.data.size == 0 condition
in perf_session__read_header). However, perf.data with partial data may
crash perf. Specifically, we see crash in 'perf script' for NULL
session->header.env.arch.
Fix this by checking session->header.env.arch before using it to determine
native_arch. Also split the if condition so it is easier to read.
Committer notes:
If it is a pipe, we already assume is a native arch, so no need to check
session->header.env.arch.
Signed-off-by: Song Liu <songliubraving@fb.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: kernel-team@fb.com
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/20211004053238.514936-1-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The following build message:
rm dlfilters/dlfilter-test-api-v0.o
is unwanted.
The object file is being treated as an intermediate file and being
automatically removed. Mark the object file as .SECONDARY to prevent
removal and hence the message.
Requested-by: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lore.kernel.org/lkml/20210930062849.110416-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Three small fixes, all in drivers, and one sizeable update to the UFS
driver to remove the HPB 2.0 feature that has been objected to by Jens
and Christoph. Although the UFS patch is large and last minute, it's
essentially the least intrusive way of resolving the objections in
time for the 5.15 release.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYX25RSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQSWAP48whPB
LUQx2tffOVmf18q5HA22mFXz/KTjgmvTVvNJtAEAn8OPN3OAnndPgBYDXAKhChI9
iMvhn3UwYGM+6DQ9bHo=
=qS2s
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three small fixes, all in drivers, and one sizeable update to the UFS
driver to remove the HPB 2.0 feature that has been objected to by Jens
and Christoph.
Although the UFS patch is large and last minute, it's essentially the
least intrusive way of resolving the objections in time for the 5.15
release"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: ufshpb: Remove HPB2.0 flows
scsi: mpt3sas: Fix reference tag handling for WRITE_INSERT
scsi: ufs: ufs-exynos: Correct timeout value setting registers
scsi: ibmvfc: Fix up duplicate response detection
to use the determine_rate instead of round_rate clk op by default. This
caused lots of problems on Rockchip SoCs because they heavily use
the composite clk code to model the clk tree.
-----BEGIN PGP SIGNATURE-----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=5b/O
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One fix for the composite clk that broke when we changed this clk type
to use the determine_rate instead of round_rate clk op by default.
This caused lots of problems on Rockchip SoCs because they heavily use
the composite clk code to model the clk tree"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: composite: Also consider .determine_rate for rate + mux composites
* A fix to ensure the trap vector's address is aligned.
* A fix to avoid re-populating the KASAN shadow memory.
* A fix to allow kasan to build without warnings, which have recently
become errors.
-----BEGIN PGP SIGNATURE-----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=BArU
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
"These are pretty late, but they do fix concrete issues.
- ensure the trap vector's address is aligned.
- avoid re-populating the KASAN shadow memory.
- allow kasan to build without warnings, which have recently become
errors"
* tag 'riscv-for-linus-5.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix asan-stack clang build
riscv: Do not re-populate shadow memory with kasan_populate_early_shadow
riscv: fix misalgned trap vector base address
The Host Performance Buffer feature allows UFS read commands to carry the
physical media addresses along with the LBAs, thus allowing less internal
L2P-table switches in the device. HPB1.0 allowed a single LBA, while
HPB2.0 increases this capacity up to 255 blocks.
Carrying more than a single record, the read operation is no longer purely
of type "read" but a "hybrid" command: Writing the physical address to the
device in one operation and reading back the required payload in another.
The JEDEC HPB spec defines two commands for this operation:
HPB-WRITE-BUFFER (0x2) to write the physical addresses to device, and
HPB-READ to read the payload.
With the current HPB design the UFS driver has no alternative but to divide
the READ request into 2 separate commands: HPB-WRITE-BUFFER and HPB-READ.
This causes a great deal of aggravation to the block layer guys who
demanded that we completely revert the entire HPB driver regardless of the
huge amount of corporate effort already invested in it.
As a compromise, remove only the pieces that implement the 2.0
specification. This is done as a matter of urgency for the final 5.15
release.
Link: https://lore.kernel.org/r/20211030062301.248-1-avri.altman@wdc.com
Tested-by: Avri Altman <avri.altman@wdc.com>
Tested-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Co-developed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Three commits fixing some issues introduced with the recent IOMMU changes we merged.
Thanks to: Alexey Kardashevskiy
-----BEGIN PGP SIGNATURE-----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=R9Yq
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.15-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Three commits fixing some issues introduced with the recent IOMMU
changes we merged.
Thanks to Alexey Kardashevskiy"
* tag 'powerpc-5.15-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries/iommu: Create huge DMA window if no MMIO32 is present
powerpc/pseries/iommu: Check if the default window in use before removing it
powerpc/pseries/iommu: Use correct vfree for it_map
- fix the return value check when parsing the ngpios property in gpio-xgs-iproc
- check the return value of bgpio_init() in gpio-mlxbf2
-----BEGIN PGP SIGNATURE-----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=Sxrc
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- fix the return value check when parsing the ngpios property in
gpio-xgs-iproc
- check the return value of bgpio_init() in gpio-mlxbf2
* tag 'gpio-fixes-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: mlxbf2.c: Add check for bgpio_init failure
gpio: xgs-iproc: fix parsing of ngpios property
Testing revealed a problem with how the reference tag was handled for
a WRITE_INSERT operation. The SCSI_PROT_REF_CHECK flag is not set when
the controller is asked to generate the protection information
(i.e. not DIX). And as a result the initial reference tag would not be
set in the WRITE_INSERT case.
Separate handling of the REF_CHECK and REF_INCREMENT flags to align
with both the DIX spec and the MPI implementation.
Link: https://lore.kernel.org/r/20211028034202.24225-1-martin.petersen@oracle.com
Fixes: b3e2c72af1d5 ("scsi: mpt3sas: Use the proper SCSI midlayer interfaces for PI")
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- tmio: Re-enable card irqs after a reset
- mtk-sd: Fixup probing of cqhci for crypto
- cqhci: Fix support for suspend/resume
- vub300: Fix control-message timeouts
- dw_mmc-exynos: Fix support for tuning
- winbond: Silences build errors on M68K
- sdhci-esdhc-imx: Fix support for tuning
- sdhci-pci: Read card detect from ACPI for Intel Merrifield
- sdhci: Fix eMMC support for Thundercomm TurboX CM2290
-----BEGIN PGP SIGNATURE-----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=SM2+
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- tmio: Re-enable card irqs after a reset
- mtk-sd: Fixup probing of cqhci for crypto
- cqhci: Fix support for suspend/resume
- vub300: Fix control-message timeouts
- dw_mmc-exynos: Fix support for tuning
- winbond: Silences build errors on M68K
- sdhci-esdhc-imx: Fix support for tuning
- sdhci-pci: Read card detect from ACPI for Intel Merrifield
- sdhci: Fix eMMC support for Thundercomm TurboX CM2290
* tag 'mmc-v5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: tmio: reenable card irqs after the reset callback
mmc: mediatek: Move cqhci init behind ungate clock
mmc: cqhci: clear HALT state after CQE enable
mmc: vub300: fix control-message timeouts
mmc: dw_mmc: exynos: fix the finding clock sample value
mmc: winbond: don't build on M68K
mmc: sdhci-esdhc-imx: clear the buffer_read_ready to reset standard tuning circuit
mmc: sdhci-pci: Read card detect from ACPI for Intel Merrifield
mmc: sdhci: Map more voltage level to SDHCI_POWER_330
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE8rQSAMVO+zA4DBdWxWXV+ddtWDsFAmF72q0ACgkQxWXV+ddt
WDvFOxAAkcryx2FP5aqaoMzBKfoCtMFHO3uAvm+rsMcglWe5kaXhBnHa2HPzoyEh
YqEx2TeXMTuA2I15bU8KV1RMhQzzRjC4NhdRqY6uaKAcKgON6sJlK5qsq2BnB+V3
nrue1jppM2Vv8wNzjMNeVETQNC7pmg29yQP/fvWaB36Yar2tyfyWDF11e42HR7cU
yLQUedg30WEayz3Mp6MTBF36h09WXQrZSs7Iwk1JMQbpxWcpn2CjXrO+vIZOMdvH
XZZsxBTNB8GJIaJlXssgsq3OP2wspK1lrVHNfi5PYtcZEaFrhkPaVB6enDfd41YV
zXwj1dnemCni9fh88gZprel9bLyB37dSVfIqq2Ly3hQbSAN4dmHIpxGwPSRIr+Hl
Bn3UfClHpAftbpd/Y77U7GgcYnkuRo3Bd4mGTF3ZuPDLVrf/QX5BlfGa2dmJYoml
NfBit7Ha4UrxLW6C8RC6fyEbLQxpNYFY55Ra0Tj0BBO/uhWiqtQGZwC/qbyPKfzN
YZFcPR6iTILoCHXNan3iZIuLeASMT0djgAtunXXf/BuFnxGfnOuqL3bKt2vojh3+
rsqpeIxSP/VklKv4JcP3axeLmUK6cA8/9dV2ES0M0Fc0o341jfh+AoVw0GleFeus
gXlDFPRJeE8yyXmjKyW4shctOczqoeMIq3umebXPP9R4jd/LU/g=
=YWGa
-----END PGP SIGNATURE-----
Merge tag 'for-5.15-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Last minute fixes for crash on 32bit architectures when compression is
in use. It's a regression introduced in 5.15-rc and I'd really like
not let this into the final release, fixes via stable trees would add
unnecessary delay.
The problem is on 32bit architectures with highmem enabled, the pages
for compression may need to be kmapped, while the patches removed that
as we don't use GFP_HIGHMEM allocations anymore. The pages that don't
come from local allocation still may be from highmem. Despite being on
32bit there's enough such ARM machines in use so it's not a marginal
issue.
I did full reverts of the patches one by one instead of a huge one.
There's one exception for the "lzo" revert as there was an
intermediate patch touching the same code to make it compatible with
subpage. I can't revert that one too, so the revert in lzo.c is
manual. Qu Wenruo has worked on that with me and verified the changes"
* tag 'for-5.15-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Revert "btrfs: compression: drop kmap/kunmap from lzo"
Revert "btrfs: compression: drop kmap/kunmap from zlib"
Revert "btrfs: compression: drop kmap/kunmap from zstd"
Revert "btrfs: compression: drop kmap/kunmap from generic helpers"
- Some bots have informed me that some of the ftrace functions kernel-doc
has formatting issues.
- Also, fix my snake instinct.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYXwAqxQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qpl+AQDn8QTG2RN9+jWVTNkCcWNNQDKPi5Ij
QYquG/clrCVnwgEAtxUoC+ZAcnsadBm5gXwjzCi62aWfAb9apkTHb6fZAgc=
=H3GU
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.15-rc6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing comment fixes from Steven Rostedt:
- Some bots have informed me that some of the ftrace functions
kernel-doc has formatting issues.
- Also, fix my snake instinct.
* tag 'trace-v5.15-rc6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix misspelling of "missing"
ftrace: Fix kernel-doc formatting issues
Pull crypto fix from Herbert Xu:
"Fix a build-time warning in x86/sm4"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: x86/sm4 - Fix invalid section entry size
Merge misc fixes from Andrew Morton:
"11 patches.
Subsystems affected by this patch series: mm (memcg, memory-failure,
oom-kill, secretmem, vmalloc, hugetlb, damon, and tools), and ocfs2"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
tools/testing/selftests/vm/split_huge_page_test.c: fix application of sizeof to pointer
mm/damon/core-test: fix wrong expectations for 'damon_split_regions_of()'
mm: khugepaged: skip huge page collapse for special files
mm, thp: bail out early in collapse_file for writeback page
mm/vmalloc: fix numa spreading for large hash tables
mm/secretmem: avoid letting secretmem_users drop to zero
ocfs2: fix race between searching chunks and release journal_head from buffer_head
mm/oom_kill.c: prevent a race between process_mrelease and exit_mmap
mm: filemap: check if THP has hwpoisoned subpage for PMD page fault
mm: hwpoison: remove the unnecessary THP check
memcg: page_alloc: skip bulk allocator for __GFP_ACCOUNT
Nathan reported that because KASAN_SHADOW_OFFSET was not defined in
Kconfig, it prevents asan-stack from getting disabled with clang even
when CONFIG_KASAN_STACK is disabled: fix this by defining the
corresponding config.
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Fixes: 8ad8b72721d0 ("riscv: Add KASAN support")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
When calling this function, all the shadow memory is already populated
with kasan_early_shadow_pte which has PAGE_KERNEL protection.
kasan_populate_early_shadow write-protects the mapping of the range
of addresses passed in argument in zero_pte_populate, which actually
write-protects all the shadow memory mapping since kasan_early_shadow_pte
is used for all the shadow memory at this point. And then when using
memblock API to populate the shadow memory, the first write access to the
kernel stack triggers a trap. This becomes visible with the next commit
that contains a fix for asan-stack.
We already manually populate all the shadow memory in kasan_early_init
and we write-protect kasan_early_shadow_pte at the end of kasan_init
which makes the calls to kasan_populate_early_shadow superfluous so
we can remove them.
Signed-off-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Fixes: e178d670f251 ("riscv/kasan: add KASAN_VMALLOC support")
Fixes: 8ad8b72721d0 ("riscv: Add KASAN support")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Some functions had kernel-doc that used a comma instead of a hash to
separate the function name from the one line description.
Also, the "ftrace_is_dead()" had an incomplete description.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This reverts commit 8c945d32e60427cbc0859cf7045bbe6196bb03d8.
The kmaps in compression code are still needed and cause crashes on
32bit machines (ARM, x86). Reproducible eg. by running fstest btrfs/004
with enabled LZO or ZSTD compression.
The revert does not apply cleanly due to changes in a6e66e6f8c1b
("btrfs: rework lzo_decompress_bio() to make it subpage compatible")
that reworked the page iteration so the revert is done to be equivalent
to the original code.
Link: https://lore.kernel.org/all/CAJCQCtT+OuemovPO7GZk8Y8=qtOObr0XTDp8jh4OHD6y84AFxw@mail.gmail.com/
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=214839
Tested-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This reverts commit bbaf9715f3f5b5ff0de71da91fcc34ee9c198ed8.
The kmaps in compression code are still needed and cause crashes on
32bit machines (ARM, x86). Reproducible eg. by running fstest btrfs/004
with enabled LZO or ZSTD compression.
Example stacktrace with ZSTD on a 32bit ARM machine:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c4159ed3
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 210 Comm: kworker/u2:3 Not tainted 5.14.0-rc79+ #12
Hardware name: Allwinner sun4i/sun5i Families
Workqueue: btrfs-delalloc btrfs_work_helper
PC is at mmiocpy+0x48/0x330
LR is at ZSTD_compressStream_generic+0x15c/0x28c
(mmiocpy) from [<c0629648>] (ZSTD_compressStream_generic+0x15c/0x28c)
(ZSTD_compressStream_generic) from [<c06297dc>] (ZSTD_compressStream+0x64/0xa0)
(ZSTD_compressStream) from [<c049444c>] (zstd_compress_pages+0x170/0x488)
(zstd_compress_pages) from [<c0496798>] (btrfs_compress_pages+0x124/0x12c)
(btrfs_compress_pages) from [<c043c068>] (compress_file_range+0x3c0/0x834)
(compress_file_range) from [<c043c4ec>] (async_cow_start+0x10/0x28)
(async_cow_start) from [<c0475c3c>] (btrfs_work_helper+0x100/0x230)
(btrfs_work_helper) from [<c014ef68>] (process_one_work+0x1b4/0x418)
(process_one_work) from [<c014f210>] (worker_thread+0x44/0x524)
(worker_thread) from [<c0156aa4>] (kthread+0x180/0x1b0)
(kthread) from [<c0100150>]
Link: https://lore.kernel.org/all/CAJCQCtT+OuemovPO7GZk8Y8=qtOObr0XTDp8jh4OHD6y84AFxw@mail.gmail.com/
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=214839
Signed-off-by: David Sterba <dsterba@suse.com>
