IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
I introduced this check here because it looked wrong in HOST only
configurions. The timer would remove that session bit and will never
come back and so there would not be another session.
Now that I played with OTG for a while I belive this workaround is
only required for the OTG mode because we have to end the session and
then we have to try to start manually.
Therefore, this patch limits this timer to the OTG only port mode so we
don't need to poll around in device only mode.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the comments, we rely on the OTG timer because the core
does not expose some important OTG details. So far this is all I
know. After playing with OTG I stumbled over a problem:
musb is recognized as a B-device without a problem. Whenever a cable is
plugged, the VBUS rises, musb recognizes this as a starting session,
sets the MUSB_DEVCTL_SESSION bit by itself and a RESET interrupt occurs,
the session starts. Good.
After a disconnect, the timer is started and re-starts itself because
it remains in B_IDLE with the BDEVICE set. I didn't figure the the
reason or the need for it. Nothing changes here except for OTG state
from B to A device if the BDEVICE bit disappears. This doesn't make much
sense to me because nothing happens after this. _IF_ we receive an
interrupt before the state change then we may act on wrong condition.
Plugging a B-device (and letting MUSB act as host) doesn't work here.
The reason seems to be that the MUSB tries to start a session, it fails
and then it removes the bit. So we never start as a host.
This patch sets the MUSB_DEVCTL_SESSION bit in the IDLE state so musb
can try to establish a session as host. After the bit is set, musb tries
to start a session and if it fails it clears the bit. Therefore it will
try over and over again until a session either as host or as device is
established.
The readout of the MUSB_DEVCTL register after the removal the
MUSB_DEVCTL_SESSION (in A_WAIT_BCON) has been removed because it did not
contain the BDEVICE bit set (in the second read) leading to A_IDLE. After
plugging a host musb assumed that it is also a host and complained about
a missing reset. However a third read of the register has has the BDEVICE
bit set so it seems that it is not stable.
This mostly what da8xx.c is doing except that we set the timer also
after A_WAIT_BCON so the session bit can be triggered.
Whit this change I was able to keep am335x-evm in OTG mode and plug in
either a HOST or a DEVICE and in a random order and the device was
recognized.
Cc: stable@vger.kernel.org # v3.11
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves dsps_musb_try_idle() before dsps_musb_enable() so the
declaration (of dsps_musb_try_idle() can be removed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The timer is initialized right after musb is probed. There is actually
no need to have this timer running because _nothing_ will happen until
we have the gadget loaded. Also we need this timer only if we run in OTG
mode _and_ we need it also after the gadget has been replaced with
another one.
I've been looking at am35x.c, da8xx.c, omap2430.c, tusb6010.c. da8xx
seem to have the same problem as dsps and doing mostly the same thing.
tusb6010 seem to do something different and do some actual "idle / power
saving" work so I am not too comfortable to remove
musb_platform_try_idle() from musb_gadget_setup().
Therefore this patch does not start the timer if there is no gadget
active (which is at musb_gadget_setup() at time). In order to have the
timer active after the gadget is loaded it will be triggered from
dsps_musb_enable().
Cc: stable@vger.kernel.org # v3.11
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In commit 001dd84 ("usb: musb: start musb on the udc side, too") it was
ensured that the state engine is started also in OTG mode after a
removal / insertion of the gadget.
Unfortunately this change also introduced a bug: If the device is
configured as OTG and it connected with a remote host _without_ loading
a gadget then we bug() later (because musb->otg->gadget is not
initialized).
Initially I assumed it might be nice to have the host part of musb in
OTG mode working without having a gadget loaded. This bug and fact that
it wasn't working like this before the host/gadget split made me realize
that this was a silly idea.
This patch now introduces back the old behavior where in OTG mode the
host mode is only working after the gadget has been loaded.
Cc: stable@vger.kernel.org # v3.11
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So I captured this:
|WARNING: CPU: 0 PID: 2078 at /home/bigeasy/work/new/TI/linux/lib/debugobjects.c:260 debug_print_object+0x94/0xc4()
|ODEBUG: free active (active state 0) object type: work_struct hint: musb_irq_work+0x0/0x38 [musb_hdrc]
|CPU: 0 PID: 2078 Comm: rmmod Not tainted 3.12.0-rc4+ #338
|[<c0014d38>] (unwind_backtrace+0x0/0xf4) from [<c001249c>] (show_stack+0x14/0x1c)
|[<c001249c>] (show_stack+0x14/0x1c) from [<c0037720>] (warn_slowpath_common+0x64/0x84)
|[<c0037720>] (warn_slowpath_common+0x64/0x84) from [<c00377d4>] (warn_slowpath_fmt+0x30/0x40)
|[<c00377d4>] (warn_slowpath_fmt+0x30/0x40) from [<c022ae90>] (debug_print_object+0x94/0xc4)
|[<c022ae90>] (debug_print_object+0x94/0xc4) from [<c022b7e0>] (debug_check_no_obj_freed+0x1c0/0x228)
|[<c022b7e0>] (debug_check_no_obj_freed+0x1c0/0x228) from [<c00f1f38>] (kfree+0xf8/0x228)
|[<c00f1f38>] (kfree+0xf8/0x228) from [<c02921c4>] (release_nodes+0x1a8/0x248)
|[<c02921c4>] (release_nodes+0x1a8/0x248) from [<c028f70c>] (__device_release_driver+0x98/0xf0)
|[<c028f70c>] (__device_release_driver+0x98/0xf0) from [<c028f840>] (device_release_driver+0x24/0x34)
|[<c028f840>] (device_release_driver+0x24/0x34) from [<c028ebe8>] (bus_remove_device+0x148/0x15c)
|[<c028ebe8>] (bus_remove_device+0x148/0x15c) from [<c028d120>] (device_del+0x104/0x1c0)
|[<c028d120>] (device_del+0x104/0x1c0) from [<c02911e4>] (platform_device_del+0x18/0xac)
|[<c02911e4>] (platform_device_del+0x18/0xac) from [<c029179c>] (platform_device_unregister+0xc/0x18)
|[<c029179c>] (platform_device_unregister+0xc/0x18) from [<bf1902fc>] (dsps_remove+0x20/0x4c [musb_dsps])
|[<bf1902fc>] (dsps_remove+0x20/0x4c [musb_dsps]) from [<c0290d7c>] (platform_drv_remove+0x1c/0x24)
|[<c0290d7c>] (platform_drv_remove+0x1c/0x24) from [<c028f704>] (__device_release_driver+0x90/0xf0)
|[<c028f704>] (__device_release_driver+0x90/0xf0) from [<c028f818>] (driver_detach+0xb4/0xb8)
|[<c028f818>] (driver_detach+0xb4/0xb8) from [<c028e6e8>] (bus_remove_driver+0x98/0xec)
|[<c028e6e8>] (bus_remove_driver+0x98/0xec) from [<c008fc70>] (SyS_delete_module+0x1e0/0x24c)
|[<c008fc70>] (SyS_delete_module+0x1e0/0x24c) from [<c000e680>] (ret_fast_syscall+0x0/0x48)
|---[ end trace d79045419a3e51ec ]---
The workqueue is only scheduled from the ep0 and never canceled in case
the musb is removed before the work has a chance to run.
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This removes the DEV_PM_OPS macro and brings this file in line with the
other musb platform drivers.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This makes bfin_pm_ops const and will stub the struct out in case
CONFIG_PM_SLEEP is not set.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This makes am35x_pm_ops const and will stub the struct out in case
CONFIG_PM_SLEEP is not set.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Ravi B <ravibabu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After commit 09fc7d22b024692b2fe8a943b246de1af307132b (usb: musb: fix incorrect
usage of resource pointer), CPPI DMA driver on DaVinci DM6467 can't detect its
dedicated IRQ and so the MUSB IRQ is erroneously used instead. This is because
only 2 resources are passed to the MUSB driver from the DaVinci glue layer, so
fix this by always copying 3 resources (it's safe since a placeholder for the
3rd resource is always there) and passing 'pdev->num_resources' instead of the
size of musb_resources[] to platform_device_add_resources().
Cc: <stable@vger.kernel.org> # 3.11+
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use platform_device_register_full() for those drivers which can, to
avoid messing directly with DMA masks. This can only be done when
the driver does not need to access the allocated musb platform device
from within its callbacks, which may be called during the musb
device probing.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
More power supply drivers depends on vbus events and without it they not
working. Power supply drivers using usb_register_notifier, so to deliver
events it is needed to call atomic_notifier_call_chain.
So without atomic notifier power supply driver isp1704 not retrieving
vbus status and reporting bogus values to userspace and also to board
platform data functions. Without proper data charger drivers trying to
charge battery also when charger is disconnected or do not start charging
when wallcharger connects.
Atomic notifier in musb driver was used before v3.5 and was replaced with
omap mailbox. This patch adding atomic_notifier_call_chain call from
function omap_musb_set_mailbox.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The Kconfig help text is talking about the U5500 which is no
longer supported by the kernel. Name the help text after the
config symbol which is more correct.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Dan Carpenter's automatic Smatch checker found an anomaly in the ux500
MUSB driver, whereby board data was checked before use in all but one
occasion. It is believed that it needs to be checked every time.
Smatch complaint:
drivers/usb/musb/ux500_dma.c:335 ux500_dma_controller_start()
error: we previously assumed 'data' could be null (see line 313)
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is what I observe:
On the first connect, the musb starts with DEVCTL.Session set. On
disconnect, musb_core calls try_idle. That functions removes the Session
bit signalizing that the session is over (something that only in OTG is
required). A new device, that is plugged, is no longer recognized.
I've setup a timer and checked the DEVCTL register and I haven't seen a
change in VBus and I saw the B-Device bit set. After setting the IDDIG
into A mode and forcing the device to behave like a A device, I didn't
see a change.
Neither VBUS goes to 0b11 nor does a session start request comes.
In the TI-v3.2 kernel they skip to call musb_platform_try_idle() in the
OTG_STATE_A_WAIT_BCON state while not in OTG mode.
Since the second port hast a standard A plug the patch changes the port
to run in host mode only and skips the timer which would remove
DEVCTL.Session so we can reconnect to another device later.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Quite early on init there is an vbus / drvvbus interrupt comming and the
dsps code sets is_active to one. As a result we see a lot of
|musb_bus_suspend 2459: trying to suspend as a_wait_bcon while active
until a device is plugged in with pm_runtime enabled in the kernel.
After checking davinci, am35, da8xx I noticed that dsps is actually the
only one doing this.
So remove it and we won't flooded with mesages and the idle port can be
suspended.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This relfects the code and dts requires changes due to recent .dts
binding updates:
- use mg prefix for the Metor Graphics specific attributes
- use power in mA not in mA/2 as specifed in the USB2.0 specification
- remove the child node for USB. This is driver specific on won't be
reflected in the device tree
- use the "mentor" prefix instead of "mg".
- use "dr_mode" istead of "mg,port-mode" for the port mode. The former
is used by a few other drivers.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb_shutdown() removes always USB host and device.
musb_init_controller() adds host and device depending on port_mode. If
port mode is set to HOST then the removal of UDC leads only to:
|(NULL device *): gadget not registered.
and nothing else happens. If port mode is set to DEVICE and we remove
the host then we oops in usb_remove_hcd().
This patch ensures that we only remove host in OTG/host mode and device
only in OTG/device mode to avoid any trouble.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
devm_ioremap_resource returns an ERR_PTR value, not NULL, on failure.
Furthermore, the value returned by devm_ioremap_resource should be tested.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1;
statement S;
@@
*e = devm_ioremap_resource(...);
if (!e1) S
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since commit 511f3c53 (usb: gadget: udc-core: fix a regression during
gadget driver unbinding) usb_gadget_remove_driver will pass NULL for
the driver argument.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add the missing unlock before return from function cppi41_dma_callback()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since dma_map_single() may fail it is good to actually check the return
code to see if it succeeded.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
All patches here have been pending on linux-usb
and sitting in linux-next for a while now.
The biggest things in this tag are:
DWC3 learned proper usage of threaded IRQ
handlers and now we spend very little time
in hardirq context.
MUSB now has proper support for BeagleBone and
Beaglebone Black.
Tegra's USB support also got quite a bit of love
and is learning to use PHY layer and generic DT
attributes.
Other than that, the usual pack of cleanups and
non-critical fixes follow.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=3NS9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.12 merge window
All patches here have been pending on linux-usb
and sitting in linux-next for a while now.
The biggest things in this tag are:
DWC3 learned proper usage of threaded IRQ
handlers and now we spend very little time
in hardirq context.
MUSB now has proper support for BeagleBone and
Beaglebone Black.
Tegra's USB support also got quite a bit of love
and is learning to use PHY layer and generic DT
attributes.
Other than that, the usual pack of cleanups and
non-critical fixes follow.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/gadget/udc-core.c
drivers/usb/host/ehci-tegra.c
drivers/usb/musb/omap2430.c
drivers/usb/musb/tusb6010.c
Since the musb-gadget code now calls the dma engine properly it is
possible to enable it for the TX path in device mode.
AM335x Advisory 1.0.13 says that we may lose the toggle bit on multiple
RX transfers. There is a workaround in host mode but none in device mode
and therefore RX transfers are disabled.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch makes use of the two function is_cppi_enabled() and
tusb_dma_omap() instead of the ifdef for the proper DMA implementation
setup code. It basically shifts the code right by one indention level
and adds a few line breaks once the chars are crossed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This driver is currently used by musb' cppi41 couter part. I may merge
both dma engine user of musb at some point but not just yet.
The driver seems to work in RX/TX mode in host mode, tested on mass
storage. I increaed the size of the TX / RX transfers and waited for the
core code to cancel a transfers and it seems to recover.
v2..3:
- use mall transfers on RX side and check data toggle.
- use rndis mode on tx side so we haveon interrupt for 4096 transfers.
- remove custom "transferred" hack and use dmaengine_tx_status() to
compute the total amount of data that has been transferred.
- cancel transfers and reclaim descriptors
v1..v2:
- RX path added
- dma mode 0 & 1 is working
- device tree nodes re-created.
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This moves the two instances from the big node into two child nodes. The
glue layer ontop does almost nothing.
There is one devices containing the control module for USB (2) phy,
(2) usb and later the dma engine. The usb device is the "glue device"
which contains the musb device as a child. This is what we do ever since.
The new file musb_am335x is just here to prob the new bus and populate
child devices.
There are a lot of changes to the dsps file as a result of the changes:
- musb_core_offset
This is gone. The device tree provides memory ressources information
for the device there is no need to "fix" things
- instances
This is gone as well. If we have two instances then we have have two
child enabled nodes in the device tree. For instance the SoC in beagle
bone has two USB instances but only one has been wired up so there is
no need to load and init the second instance since it won't be used.
- dsps_glue is now per glue device
In the past there was one of this structs but with an array of two and
each instance accessed its variable depending on the platform device
id.
- no unneeded copy of structs
I do not know why struct dsps_musb_wrapper is copied but it is not
necessary. The same goes for musb_hdrc_platform_data which allocated
on demand and then again by platform_device_add_data(). One copy is
enough.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dsps uses a nop driver which is added in dsps itself and does the PHY
on/off calls within dsps. Since those calls are now moved the nop driver
itself, we can now request the phy proper phy and remove those calls.
Currently only the first musb interface is used so we only add one phy
node for now.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The "nop" driver isn't a do-nothing-stub but supports a couple functions
like clock on/off or is able to use a voltage regulator. This patch
simply renames the driver to "generic" since it is easy possible to
extend it by a simple function istead of writing a complete driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The EOI register is not present in the AM335x memory space according to
the TRM and thus removed.
Should any platform using the EOI register get merged then it may be
used again if the register address is not zero.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The ti81xx platform is not fully supported right now. This patch renames
the date structure to a am33xx prefix which is actually used.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 8d2421e ("usb: musb: kill global and static for multi instance")
removed the global dma_mask copy and replaced by parent's DMA mask. The
problem here is that if the parent does not have a dma_mask then
musb_remove() goes kaboom.
Instead trying to fix this I was thinking we do we need to erase
dma_mask in the first place?
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ti81xx does not have a baseport mainline i.e. it should not boot. The
amount of rework that is required makes it easier to simply remove that
platform (i.e. that possible platform device) and add it later once it
comes back with DT support.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the init / shutdown function of the phy moves out of dsps into the
phy driver, then dsps needs to call the callbacks of the phy driver to
ensure that this happens.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The musb driver no longer uses procfs, so get rid of the proc_dir_entry
variable in struct musb.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the descriptor is missing the reqeust is never unmapped. This patch
changes this and renames the cleanup label to unlock since there is no
cleanup done. The cleanup would revert the allocation of ressource (i.e.
this dma mapping) but it does not, it simply unlocks and returns.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The cleanup in the error is missing the dma controller. The structure is
allocated at runtime and ux500 allocates even a little more than just
this struct. So cleanup!
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes is_dma_capable() and an ifdef in the init/exit path
around init/de-init of the dma_controller. Since we have the empty stubs
in the PIO code we can call it without gcc trouble. Earlier we had an
ifdef and the is_dma_capable() macro where gcc ignored the if (0) path
even that the function was not around :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add a dma_controller_create() returning NULL so a few ifdefs can
dropped.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The core code creates a controller and immediately after that it calls
the ->start() callback. This one might drop an error but nobody cares.
The same thing happens in the destroy corner: First ->stop() called
followed by destroy callback. So why not merge those two into the same
function since there is no difference.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This check is hardly required and alas is wrong. 'c' might be NULL but
the chances are low that 'controller' after the container_of() becomes
NULL.
Since no other DMA implementation is doing that and musb-core does not
call it with a NULL pointer it can dropped.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The ifdef reads somehow better than an ifndef
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
None of these USB files need idr.h, so don't include it.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
