IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
In read_domain_devices(), acpi_bus_get_device() is called to obtain
the ACPI device object attached to the given ACPI handle and
subsequently that object is passed to get_device() for reference
counting, but there is a window between the acpi_bus_get_device()
and get_device() calls in which the ACPI device object in question
may go away.
To address this issue, make read_domain_devices() use
acpi_bus_get_acpi_device() to reference count and return the given
ACPI device object in one go and export that function to modules.
While at it, also make read_domain_devices() and
remove_domain_devices() use acpi_dev_put() instead of calling
put_device() directly on the ACPI device objects returned by
acpi_bus_get_acpi_device().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/11871063.O9o76ZdvQC@kreacher
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The nominal speed of each fan can be obtained with
i8k_get_fan_nominal_speed(), however the result is not available
from userspace.
Change that by adding fanX_min, fanX_max and fanX_target attributes.
All are RO since fan control happens over pwm.
Tested on a Dell Inspiron 3505 and a Dell Latitude C600.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210926221044.14327-2-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Recent patch added possibility to disable selected channels. That would
only make sure that the ENODATA is returned for those channels but would
not configure the actual hardware.
With this patch, the config register is written to make sure the
channels are disabled also at hardware level.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Link: https://lore.kernel.org/r/d451cacdf21bf8eff38a47c055aad8c0c6e8755a.1634206677.git.krzysztof.adamski@nokia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Previous patches added a way to specify some channel specific parameters
in DT and n-factor is definitely one of them. This calibration mechanism
is board specific as its value depends on the diodes/transistors being
connected to the sensor and thus the DT seems like a right fit for that
information. It is very similar to the value of shunt resistor that some
drivers allows specifying in DT.
This patch adds a possibility to set n-factor for each channel via
"n-factor" DT property in each channel subnode.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Link: https://lore.kernel.org/r/69d0bfcc5ba27c67f21d3eabfb100656a14c75b9.1634206677.git.krzysztof.adamski@nokia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The previous patch introduced per channel subnodes in DT that let us
specify some channel specific properties. This built a ground for easily
disabling individual channels of the sensor that may not be connected to
any external diode and thus are not returning any meaningful data.
This patch adds support for parsing the "status" property of channels DT
subnodes and makes sure the -ENODATA is returned when disabled channels
value is read.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Link: https://lore.kernel.org/r/a85d623f0792b862870933a875bdf802f4c017f1.1634206677.git.krzysztof.adamski@nokia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
tmp42x is a multichannel temperature sensor with several external
channels. Since those channels can be used to connect diodes placed
anywhere in the system, their meaning will vary depending on the
project. For this case, the hwmon framework has an idea of labels which
allows us to assign the meaning to each channel.
The similar concept is already implemented in ina3221 - the label for
each channel can be defined via device tree. See commit a9e9dd9c6de5
("hwmon: (ina3221) Read channel input source info from DT")
This patch adds support for similar feature to tmp421.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Link: https://lore.kernel.org/r/dab0fda6ac0e8d7f163c3762a7fb1e595a4d8159.1634206677.git.krzysztof.adamski@nokia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Up to now adt7x10_remove() returns zero unconditionally. Make it return
void instead which makes it easier to see in the callers that there is
no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211011132754.2479853-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Document bindings for NXP SE97B, a DDR memory module temperature sensor
with integrated SPD and EEPROM via Atmel's AT24 interface.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210920182114.339419-6-krzysztof.kozlowski@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We have bool so use it consistently in all the drivers.
The following Coccinelle script was used:
@@
identifier T;
type t = { char, int };
@@
struct T {
...
- t valid;
+ bool valid;
...
}
@@
identifier v;
@@
(
- v->valid = 0
+ v->valid = false
|
- v->valid = 1
+ v->valid = true
)
followed by sed to fixup the comments:
sed '/bool valid;/{s/!=0/true/;s/zero/false/}'
Few whitespace changes were fixed manually. All modified drivers were
compile-tested.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20210924195202.27917-1-fercerpav@gmail.com
[groeck: Fixed up 'u8 valid' to 'boool valid' in atxp1.c]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Provide different names for cooling devices registration to allow
binding each cooling devices to relevant thermal zone. Thus, specific
cooling device can be associated with related thermal sensor by setting
thermal cooling device type for example to "mlxreg_fan2" and passing
this type to thermal_zone_bind_cooling_device() through 'cdev->type'.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210926053541.1806937-3-vadimp@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Validate PWM connectivity only for additional PWM - "pwm1" is connected
on all systems, while "pwm2" - "pwm4" are optional. Validate
connectivity only for optional attributes by reading of related "pwm{n}"
registers - in case "pwm{n}" is not connected, register value is
supposed to be 0xff.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210926053541.1806937-2-vadimp@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ASUS Pro WS X570-ACE board has got an nct6775 chip, but by default
there's no use of it because of resource conflict:
```
ACPI Warning: SystemIO range 0x0000000000000295-0x0000000000000296 conflicts with OpRegion 0x0000000000000290-0x0000000000000299 (\AMW0.SHWM) (20210604/utaddress-204
)
ACPI: OSL: Resource conflict; ACPI support missing from driver?
ACPI: OSL: Resource conflict: System may be unstable or behave erratically
```
A workaround is to use `acpi_enforce_resources=lax`, but a proper
support needs to be added instead.
This commit adds Pro WS X570-ACE to the list of boards that can be monitored
using ASUS WMI.
Tested by me on this hardware:
```
Base Board Information
Manufacturer: ASUSTeK COMPUTER INC.
Product Name: Pro WS X570-ACE
BIOS Information
Vendor: American Megatrends Inc.
Version: 3801
Release Date: 07/30/2021
```
Signed-off-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Link: https://lore.kernel.org/r/20211003133344.9036-2-oleksandr@natalenko.name
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There are multiple power supplies that will indicate
CFFPS_CCIN_VERSION_1, use the manufacturer ID to determine if it should
be treated as version cffps1 or version cffps2.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Link: https://lore.kernel.org/r/20211004144339.2634330-2-bjwyman@gmail.com
[groeck: Fixed continuation line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The appropriate mantissa values for the lm25066 family's direct-format
current and power readings are a function of the sense resistor
employed between the SENSE and VIN pins of the chip. Instead of
assuming that resistance is always the same 1mOhm as used in the
datasheet, allow it to be configured via a device-tree property
("shunt-resistor-micro-ohms").
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210928092242.30036-8-zev@bewilderbeest.net
[groeck: Fixed checkpatch warnings]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210928092242.30036-7-zev@bewilderbeest.net
[groeck: Replaced reference to reasoning with reasoning, fixed checkpatch
warnings, fixed compile warning comparing of_id->data w/ i2c_id->driver_data]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Maintaining this manually is error prone (there are currently only
five chips supported, not six); gcc can do it for us automatically.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 666c14906b49 ("hwmon: (pmbus/lm25066) Drop support for LM25063")
Link: https://lore.kernel.org/r/20210928092242.30036-5-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
At least as of Revision J, the datasheet has a slightly different
value than what we'd had in the driver.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210928092242.30036-3-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
With the exception of the lm5066i, all the devices handled by this
driver had been missing their offset ('b') coefficients for direct
format readings.
Cc: stable@vger.kernel.org
Fixes: 58615a94f6a1 ("hwmon: (pmbus/lm25066) Add support for LM25056")
Fixes: e53e6497fc9f ("hwmon: (pmbus/lm25066) Refactor device specific coefficients")
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210928092242.30036-2-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The IBM Common Form Factor Power Supply Versions 1 and 2 bindings are
trivial, so they can be integrated into trivial devices bindings.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210921102832.143352-3-krzysztof.kozlowski@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This converts the NTC thermistor DT bindings to YAML. Some care had to
be taken since I had to add some illustrations to make the connection
layouts graspable.
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Johannes Pointner <johannes.pointner@gmail.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210922233901.1871274-1-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There are few places where the maximal number of channels is used define
the size of arrays but when raw number is used it is not clear that they
really related to this quantity.
This commit introduces MAX_CHANNELS define and uses it those places to
give some context to the number.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Link: https://lore.kernel.org/r/abc1a213a25b890b799b35ad94bb543a2ade7fc8.1632473318.git.krzysztof.adamski@nokia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The hih6130 bindings are trivial, so it can be integrated into trivial
devices bindings.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210920182114.339419-4-krzysztof.kozlowski@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The dps650ab bindings are trivial, so it can be integrated into trivial
devices bindings.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210920182114.339419-3-krzysztof.kozlowski@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
gmt,g751 is covered by LM75 sensor bindings. This fixes warning:
arch/arm/boot/dts/gemini-dlink-dns-313.dt.yaml: temperature-sensor@48:
'#thermal-sensor-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210920182114.339419-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The TI TMP102 temperature sensor does not fit into trivial devices
bindings due to additional properties. Add separate bindings for it.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210921102832.143352-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The lm70 thermometer bindings are trivial, so like many other I2C/SPI
temperature sensors can be integrated into trivial devices bindings.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210920182114.339419-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The LM90-like sensors usually need VCC supply, however this can be
hard-wired to the board main supply (like in SiFive HiFive Unmatched
RISC-V board). Original bindings made VCC supply as required but in
practice several other boards skipped it. Make it optional.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210920181913.338772-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Array fan->pwm[] is MLXREG_FAN_MAX_PWM elements in size, however the
for-loop has a off-by-one error causing index i to be out of range
causing an out of bounds read on the array. Fix this by replacing
the <= operator with < in the for-loop.
Addresses-Coverity: ("Out-of-bounds read")
Reported-by: Vadim Pasternak <vadimp@nvidia.com>
Fixes: 35edbaab3bbf ("hwmon: (mlxreg-fan) Extend driver to support multiply cooling devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210920180921.16246-1-colin.king@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Support accessing the NCT677x via Asus WMI functions.
On mainboards that support this way of accessing the chip, the driver will
usually not work without this option since in these mainboards, ACPI will
mark the I/O port as used.
Code uses ACPI firmware interface to communicate with sensors with ASUS
motherboards:
* PRIME B460-PLUS,
* ROG CROSSHAIR VIII IMPACT,
* ROG STRIX B550-E GAMING,
* ROG STRIX B550-F GAMING,
* ROG STRIX B550-F GAMING (WI-FI),
* ROG STRIX Z490-I GAMING,
* TUF GAMING B550M-PLUS,
* TUF GAMING B550M-PLUS (WI-FI),
* TUF GAMING B550-PLUS,
* TUF GAMING X570-PLUS,
* TUF GAMING X570-PRO (WI-FI).
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204807
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
Co-developed-by: Bernhard Seibold <mail@bernhard-seibold.de>
Signed-off-by: Bernhard Seibold <mail@bernhard-seibold.de>
Tested-by: Pär Ekholm <pehlm@pekholm.org>
Tested-by: <to.eivind@gmail.com>
Tested-by: Artem S. Tashkinov <aros@gmx.com>
Tested-by: Vittorio Roberto Alfieri <me@rebtoor.com>
Tested-by: Sahan Fernando <sahan.h.fernando@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210917220240.56553-4-pauk.denis@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
