IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Instead of doing the full DASH check each time r8168_check_dash() is
called, let's do it once in probe and store DASH capabilities in a
new rtl8169_private member.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend the mask to include the checksum failure bits. This allows to
simplify the condition in rtl8169_rx_csum().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At least from chip version 25 the vendor driver sets these rx flags
for all chip versions if WOL is enabled. Therefore I wouldn't consider
it a quirk, so let's rename the function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PHYLIB must be selected to provide mdiobus_*() functions, and the
MICREL_PHY is necessary too, as that is the only possible PHY attached
to the KS8851 (it is the internal PHY).
Fixes: ef3631220d2b ("net: ks8851: Register MDIO bus and the internal PHY")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210111125046.36326-1-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Patch didn't fix any issue, just improve parse flow
and align ipv4 parse flow with ipv6 parse flow.
Currently ipv4 kenguru parser first check IP protocol(TCP/UDP)
and then destination IP address.
Patch introduce reverse ipv4 parse, first destination IP address parsed
and only then IP protocol.
This would allow extend capability for packet L4 parsing and align ipv4
parsing flow with ipv6.
Suggested-by: Liron Himi <liron@marvell.com>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Link: https://lore.kernel.org/r/1610289059-14962-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
List of things fixed:
- Two of the socket options were idented with spaces instead of tabs.
- Trailing whitespace in some lines.
- Improper spacing around parenthesis caught by checkpatch.pl.
- Mix of space and tabs in tcp_word_hdr union.
Signed-off-by: Danilo Carvalho <doak@google.com>
Link: https://lore.kernel.org/r/20210108222104.2079472-1-doak@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bareudp_dellink() only needs the device list to hand it to
unregister_netdevice_queue(). We can pass NULL in, and
unregister_netdevice_queue() will do the unregistering.
There is no chance for batching on the error path, anyway.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Link: https://lore.kernel.org/r/20210111052922.2145003-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit says:
====================
r8169: improve PLL power-down handling
This series includes improvements to handling of PLL power-down.
====================
Link: https://lore.kernel.org/r/1608dfa3-c4a5-0e92-31f7-76674b3c173a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clean up the remainings of rtl_pll_power_down/up and rename
rtl_pll_power_down() to rtl_prepare_power_down().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Realtek provided a description of bits 6 and 7 in register PMCH.
They configure whether the chip powers down certain PLL in D3hot and
D3cold respectively. They do not actually power down the PLL.
Reflect this in the code and configure D3 PLL powerdown based on
whether WOL is enabled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's no known reason why PLL powerdown on D3 shouldn't be enabled
on chip versions 34, 35, 36, and 42. At least the vendor driver doesn't
exclude any of these chip versions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
So far we don't increase the max read request size if we switch to
jumbo mode before bringing up the interface for the first time.
Let's change this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Align behavior with r8168 vendor driver and don't reduce max read
request size for RTL8168e in jumbo mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert at803x_clk_out_config() to use phy_modify_mmd().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1kyc72-0008Pq-1x@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend the bitrate-derived support to include 2500BASE-X for modules
that report a bitrate of 2500Mbaud.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1kyYQf-0004iY-Gh@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SFP MSA defines two option bits in byte 65 to indicate how the
Rx_LOS signal on SFP pin 8 behaves:
bit 2 - Loss of Signal implemented, signal inverted from standard
definition in SFP MSA (often called "Signal Detect").
bit 1 - Loss of Signal implemented, signal as defined in SFP MSA
(often called "Rx_LOS").
Clearly, setting both bits results in a meaningless situation: it would
mean that LOS is implemented in both the normal sense (1 = signal loss)
and inverted sense (0 = signal loss).
Unfortunately, there are modules out there which set both bits, which
will be initially interpret as "inverted" sense, and then, if the LOS
signal changes state, we will toggle between LINK_UP and WAIT_LOS
states.
Change our LOS handling to give well defined behaviour: only interpret
these bits as meaningful if exactly one is set, otherwise treat it as
if LOS is not implemented.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1kyYQa-0004iR-CU@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The code that sets the DMA mask to 64 bits is bogus, it is taken from
the enetc driver together with the rest of the PCI probing boilerplate.
Since this patch is touching the error path to delete err_dma, let's
also change the err_alloc_felix label which was incorrect. The kzalloc
failure does not need a kfree, but it doesn't hurt either, since kfree
works with NULL pointers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210109203415.2120142-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean says:
====================
Get rid of the switchdev transactional model
Changes in v4:
- Fixed build error in dsa_loop and build warning in hellcreek driver.
- Scheduling the mlxsw SPAN work item regardless of the VLAN add return
code, as per Ido's and Petr's request.
Changes in v3:
- Resolved a build warning in mv88e6xxx and tested that it actually
works properly, which resulted in an extra patch (02/11).
- Addressed Ido's minor feedback in commit 10/11 relating to a comment.
Changes in v2:
- Got rid of the vid_begin -> vid_end range too from the switchdev API.
- Actually propagating errors from DSA MDB and VLAN notifiers.
This series comes after the late realization that the prepare/commit
separation imposed by switchdev does not help literally anybody:
https://patchwork.kernel.org/project/netdevbpf/patch/20201212203901.351331-1-vladimir.oltean@nxp.com/
We should kill it before it inflicts even more damage to the error
handling logic in drivers.
Also remove the unused VLAN ranges feature from the switchdev VLAN
objects, which simplifies all drivers by quite a bit.
====================
Link: https://lore.kernel.org/r/20210109000156.1246735-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that all users of struct switchdev_trans have been modified to do
without it, we can remove this structure and the two helpers to determine
the phase.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As of commit 457e20d65924 ("mlxsw: spectrum_switchdev: Avoid returning
errors in commit phase"), the mlxsw driver performs the VLAN object
offloading during the prepare phase. So conversion just seems to be a
matter of removing the code that was running in the commit phase.
Ido Schimmel explains that the reason why mlxsw_sp_span_respin is called
unconditionally is because the bridge driver will ignore -EOPNOTSUPP and
actually add the VLAN on the bridge device - see commit 9c86ce2c1ae3
("net: bridge: Notify about bridge VLANs") and commit ea4721751977
("mlxsw: spectrum_switchdev: Ignore bridge VLAN events"). Since the VLAN
was successfully added on the bridge device, mlxsw_sp_span_respin_work()
should be able to resolve the egress port for a packet that is mirrored
to a gre tap and passes through the bridge device. Therefore keep the
logic as it is.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that all port object notifiers were converted to be non-transactional,
we can remove the comments that say otherwise.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It should be the driver's business to logically separate its VLAN
offloading into a preparation and a commit phase, and some drivers don't
need / can't do this.
So remove the transactional shim from DSA and let drivers propagate
errors directly from the .port_vlan_add callback.
It would appear that the code has worse error handling now than it had
before. DSA is the only in-kernel user of switchdev that offloads one
switchdev object to more than one port: for every VLAN object offloaded
to a user port, that VLAN is also offloaded to the CPU port. So the
"prepare for user port -> check for errors -> prepare for CPU port ->
check for errors -> commit for user port -> commit for CPU port"
sequence appears to make more sense than the one we are using now:
"offload to user port -> check for errors -> offload to CPU port ->
check for errors", but it is really a compromise. In the new way, we can
catch errors from the commit phase that we previously had to ignore.
But we have our hands tied and cannot do any rollback now: if we add a
VLAN on the CPU port and it fails, we can't do the rollback by simply
deleting it from the user port, because the switchdev API is not so nice
with us: it could have simply been there already, even with the same
flags. So we don't even attempt to rollback anything on addition error,
just leave whatever VLANs managed to get offloaded right where they are.
This should not be a problem at all in practice.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For many drivers, the .port_mdb_prepare callback was not a good opportunity
to avoid any error condition, and they would suppress errors found during
the actual commit phase.
Where a logical separation between the prepare and the commit phase
existed, the function that used to implement the .port_mdb_prepare
callback still exists, but now it is called directly from .port_mdb_add,
which was modified to return an int code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Wallei <linus.walleij@linaro.org> # RTL8366
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the shim introduced in DSA for offloading the bridge ageing time
from switchdev, by first checking whether the ageing time is within the
range limits requested by the driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the introduction of the switchdev API, port attributes were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.
Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8eceffc1 ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.
It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.
This patch removes the struct switchdev_trans member from switchdev port
attribute notifier structures, and converts drivers to not look at this
member.
In part, this patch contains a revert of my previous commit 2e554a7a5d8a
("net: dsa: propagate switchdev vlan_filtering prepare phase to
drivers").
For the most part, the conversion was trivial except for:
- Rocker's world implementation based on Broadcom OF-DPA had an odd
implementation of ofdpa_port_attr_bridge_flags_set. The conversion was
done mechanically, by pasting the implementation twice, then only
keeping the code that would get executed during prepare phase on top,
then only keeping the code that gets executed during the commit phase
on bottom, then simplifying the resulting code until this was obtained.
- DSA's offloading of STP state, bridge flags, VLAN filtering and
multicast router could be converted right away. But the ageing time
could not, so a shim was introduced and this was left for a further
commit.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> # RTL8366RB
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After the removal of the transactional model inside
switchdev_port_obj_add_now, it has no added value and we can just call
switchdev_port_obj_notify directly, bypassing this function. Let's
delete it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the introduction of the switchdev API, port objects were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.
Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8eceffc1 ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.
It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.
This patch removes the struct switchdev_trans member from switchdev port
object notifier structures, and converts drivers to not look at this
member.
Where driver conversion is trivial (like in the case of the Marvell
Prestera driver, NXP DPAA2 switch, TI CPSW, and Rocker drivers), it is
done in this patch.
Where driver conversion needs more attention (DSA, Mellanox Spectrum),
the conversion is left for subsequent patches and here we only fake the
prepare/commit phases at a lower level, just not in the switchdev
notifier itself.
Where the code has a natural structure that is best left alone as a
preparation and a commit phase (as in the case of the Ocelot switch),
that structure is left in place, just made to not depend upon the
switchdev transactional model.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mv88e6xxx apparently has a problem offloading VID 0, which the 8021q
module tries to install as part of commit ad1afb003939 ("vlan_dev: VLAN
0 should be treated as "no vlan tag" (802.1p packet)"). That mv88e6xxx
restriction seems to have been introduced by the "VTU GetNext VID-1
trick to retrieve a single entry" - see commit 2fb5ef09de7c ("net: dsa:
mv88e6xxx: extract single VLAN retrieval").
There is one more problem. The mv88e6xxx CPU port and DSA links do not
report properly in the prepare phase what are the VLANs that they can
offload. They'll say they can offload everything:
mv88e6xxx_port_vlan_prepare
-> mv88e6xxx_port_check_hw_vlan:
/* DSA and CPU ports have to be members of multiple vlans */
if (dsa_is_dsa_port(ds, port) || dsa_is_cpu_port(ds, port))
return 0;
Except that if you actually try to commit to it, they'll error out and
print this message:
[ 32.802438] mv88e6085 d0032004.mdio-mii:12: p9: failed to add VLAN 0t
which comes from:
mv88e6xxx_port_vlan_add
-> mv88e6xxx_port_vlan_join:
if (!vid)
return -EOPNOTSUPP;
What prevents this condition from triggering in real life? The fact that
when a DSA_NOTIFIER_VLAN_ADD is emitted, it never targets a DSA link
directly. Instead, the notifier will always target either a user port or
a CPU port. DSA links just happen to get dragged in by:
static bool dsa_switch_vlan_match(struct dsa_switch *ds, int port,
struct dsa_notifier_vlan_info *info)
{
...
if (dsa_is_dsa_port(ds, port))
return true;
...
}
So for every DSA VLAN notifier, during the prepare phase, it will just
so happen that there will be somebody to say "no, don't do that".
This will become a problem when the switchdev prepare/commit transactional
model goes away. Every port needs to think on its own. DSA links can no
longer bluff and rely on the fact that the prepare phase will not go
through to the end, because there will be no prepare phase any longer.
Fix this issue before it becomes a problem, by having the "vid == 0"
check earlier than the check whether we are a CPU port / DSA link or not.
Also, the "vid == 0" check becomes unnecessary in the .port_vlan_add
callback, so we can remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The call path of a switchdev VLAN addition to the bridge looks something
like this today:
nbp_vlan_init
| __br_vlan_set_default_pvid
| | |
| | br_afspec |
| | | |
| | v |
| | br_process_vlan_info |
| | | |
| | v |
| | br_vlan_info |
| | / \ /
| | / \ /
| | / \ /
| | / \ /
v v v v v
nbp_vlan_add br_vlan_add ------+
| ^ ^ | |
| / | | |
| / / / |
\ br_vlan_get_master/ / v
\ ^ / / br_vlan_add_existing
\ | / / |
\ | / / /
\ | / / /
\ | / / /
\ | / / /
v | | v /
__vlan_add /
/ | /
/ | /
v | /
__vlan_vid_add | /
\ | /
v v v
br_switchdev_port_vlan_add
The ranges UAPI was introduced to the bridge in commit bdced7ef7838
("bridge: support for multiple vlans and vlan ranges in setlink and
dellink requests") (Jan 10 2015). But the VLAN ranges (parsed in br_afspec)
have always been passed one by one, through struct bridge_vlan_info
tmp_vinfo, to br_vlan_info. So the range never went too far in depth.
Then Scott Feldman introduced the switchdev_port_bridge_setlink function
in commit 47f8328bb1a4 ("switchdev: add new switchdev bridge setlink").
That marked the introduction of the SWITCHDEV_OBJ_PORT_VLAN, which made
full use of the range. But switchdev_port_bridge_setlink was called like
this:
br_setlink
-> br_afspec
-> switchdev_port_bridge_setlink
Basically, the switchdev and the bridge code were not tightly integrated.
Then commit 41c498b9359e ("bridge: restore br_setlink back to original")
came, and switchdev drivers were required to implement
.ndo_bridge_setlink = switchdev_port_bridge_setlink for a while.
In the meantime, commits such as 0944d6b5a2fa ("bridge: try switchdev op
first in __vlan_vid_add/del") finally made switchdev penetrate the
br_vlan_info() barrier and start to develop the call path we have today.
But remember, br_vlan_info() still receives VLANs one by one.
Then Arkadi Sharshevsky refactored the switchdev API in 2017 in commit
29ab586c3d83 ("net: switchdev: Remove bridge bypass support from
switchdev") so that drivers would not implement .ndo_bridge_setlink any
longer. The switchdev_port_bridge_setlink also got deleted.
This refactoring removed the parallel bridge_setlink implementation from
switchdev, and left the only switchdev VLAN objects to be the ones
offloaded from __vlan_vid_add (basically RX filtering) and __vlan_add
(the latter coming from commit 9c86ce2c1ae3 ("net: bridge: Notify about
bridge VLANs")).
That is to say, today the switchdev VLAN object ranges are not used in
the kernel. Refactoring the above call path is a bit complicated, when
the bridge VLAN call path is already a bit complicated.
Let's go off and finish the job of commit 29ab586c3d83 by deleting the
bogus iteration through the VLAN ranges from the drivers. Some aspects
of this feature never made too much sense in the first place. For
example, what is a range of VLANs all having the BRIDGE_VLAN_INFO_PVID
flag supposed to mean, when a port can obviously have a single pvid?
This particular configuration _is_ denied as of commit 6623c60dc28e
("bridge: vlan: enforce no pvid flag in vlan ranges"), but from an API
perspective, the driver still has to play pretend, and only offload the
vlan->vid_end as pvid. And the addition of a switchdev VLAN object can
modify the flags of another, completely unrelated, switchdev VLAN
object! (a VLAN that is PVID will invalidate the PVID flag from whatever
other VLAN had previously been offloaded with switchdev and had that
flag. Yet switchdev never notifies about that change, drivers are
supposed to guess).
Nonetheless, having a VLAN range in the API makes error handling look
scarier than it really is - unwinding on errors and all of that.
When in reality, no one really calls this API with more than one VLAN.
It is all unnecessary complexity.
And despite appearing pretentious (two-phase transactional model and
all), the switchdev API is really sloppy because the VLAN addition and
removal operations are not paired with one another (you can add a VLAN
100 times and delete it just once). The bridge notifies through
switchdev of a VLAN addition not only when the flags of an existing VLAN
change, but also when nothing changes. There are switchdev drivers out
there who don't like adding a VLAN that has already been added, and
those checks don't really belong at driver level. But the fact that the
API contains ranges is yet another factor that prevents this from being
addressed in the future.
Of the existing switchdev pieces of hardware, it appears that only
Mellanox Spectrum supports offloading more than one VLAN at a time,
through mlxsw_sp_port_vlan_set. I have kept that code internal to the
driver, because there is some more bookkeeping that makes use of it, but
I deleted it from the switchdev API. But since the switchdev support for
ranges has already been de facto deleted by a Mellanox employee and
nobody noticed for 4 years, I'm going to assume it's not a biggie.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com> # switchdev and mlxsw
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RTL8168dp is ancient anyway, and I haven't seen any trace of its early
version 27 yet. This chip versions needs quite some special handling,
therefore it would facilitate driver maintenance if support for it
could be dropped. For now just disable detection of this chip version.
If nobody complains we can remove support for it in the near future.
v2:
- extend unknown chip version error message
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/ca98f018-a0e1-8762-e95c-f0ad773a0271@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM4908 family SoCs come with integrated Starfighter 2 switch. Its
registers layout it a mix of BCM7278 and BCM7445. It has 5 integrated
PHYs and 8 ports. It also supports RGMII and SerDes.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210106213202.17459-3-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This helps validating DTS files. Only the current (not deprecated one)
binding was converted.
Minor changes:
1. Dropped dsa/dsa.txt references
2. Updated node name to match dsa.yaml requirement
3. Fixed 2 typos in examples
The new binding was validated using the dt_binding_check.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20210106213202.17459-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mat Martineau says:
====================
MPTCP: Add MP_PRIO support and rework local address IDs
Patches 1 and 2 rework the assignment of local address IDs to allow them
to be assigned by a userspace path manager, and add corresponding self
tests.
Patches 2-8 add the ability to change subflow priority after a subflow
has been established. Each subflow in a MPTCP connection has a priority
level: "regular" or "backup". Data should only be sent on backup
subflows if no regular subflows are available. The priority level can be
set when the subflow connection is established (as was already
implemented), or during the life of the connection by sending MP_PRIO in
the TCP options (as added here). Self tests are included.
====================
Link: https://lore.kernel.org/r/20210109004802.341602-1-mathew.j.martineau@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added the MP_PRIO testcases:
Add a new argument bkup for run_tests and do_transfer, it can be set as
"backup" or "nobackup", the default value is "".
Add a new function chk_prio_nr to check the MP_PRIO related MIB counters.
The output looks like this:
29 single subflow, backup syn[ ok ] - synack[ ok ] - ack[ ok ]
ptx[ ok ] - prx [ ok ]
30 single address, backup syn[ ok ] - synack[ ok ] - ack[ ok ]
add[ ok ] - echo [ ok ]
ptx[ ok ] - prx [ ok ]
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added the mibs for MP_PRIO, MPTCP_MIB_MPPRIOTX for transmitting
of the MP_PRIO suboption, and MPTCP_MIB_MPPRIORX for receiving of it.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added the set_flags command in pm_nl_ctl, currently we can only
set two flags: backup and nobackup. The set_flags command can be used like
this:
# pm_nl_ctl set 10.0.0.1 flags backup
# pm_nl_ctl set 10.0.0.1 flags nobackup
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added a new command MPTCP_PM_CMD_SET_FLAGS in PM netlink:
In mptcp_nl_cmd_set_flags, parse the input address, get the backup value
according to whether the address's FLAG_BACKUP flag is set from the
user-space. Then check whether this address had been added in the local
address list. If it had been, then call mptcp_nl_addr_backup to deal with
this address.
In mptcp_nl_addr_backup, traverse all the existing msk sockets to find
the relevant sockets, and call mptcp_pm_nl_mp_prio_send_ack to send out
a MP_PRIO ACK packet.
Finally in mptcp_nl_cmd_set_flags, set or clear the address's FLAG_BACKUP
flag.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added the incoming MP_PRIO logic:
Added a flag named mp_prio in struct mptcp_options_received, to mark the
MP_PRIO is received, and save the priority value to struct
mptcp_options_received's backup member. Then invoke
mptcp_pm_mp_prio_received with the receiving subsocket and the backup
value.
In mptcp_pm_mp_prio_received, get the subflow context according the input
subsocket, and change the subflow's backup as the incoming priority value.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added the outgoing MP_PRIO logic:
In mptcp_pm_nl_mp_prio_send_ack, find the related subflow and subsocket
according to the input parameter addr. Save the input priority value to
suflow's backup, then set subflow's send_mp_prio flag to true, and save
the input priority value to suflow's request_bkup. Finally, send out a
pure ACK on the related subsocket.
In mptcp_established_options_mp_prio, check whether the subflow's
send_mp_prio is set. If it is, this is the packet for sending MP_PRIO.
So save subflow->request_bkup value to mptcp_out_options's backup, and
change the option type to OPTION_MPTCP_PRIO.
In mptcp_write_options, clear the send_mp_prio flag and send out the
MP_PRIO suboption with mptcp_out_options's backup value.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the address ID can be set from user-space, some of the tests in
pm_netlink.sh will fail. This patch fixed the failures, and add the
testcases for setting the address ID.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the address ID set by the netlink PM from user-space is
overridden by the kernel. This patch added the address ID assignment
bitmap to allow user-space to set the address ID.
Use a per netns bitmask id_bitmap (256 bits) to keep track of in-use IDs.
And use next_id to keep track of the highest ID currently in use. If the
user-space provides an ID at endpoint creation time, try to use it. If
already in use, endpoint creation fails. Otherwise pick the first ID
available after the highest currently in use, with wrap-around.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit says:
====================
r8169: small improvements
This series includes a number of smaller improvements.
v2:
- return on WARN in patch 1
====================
Link: https://lore.kernel.org/r/938caef4-8a0b-bbbd-66aa-76f758ff877a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If WOL isn't enabled, then there's no need to enable wakeup from D3
on system shutdown.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use WARN_ONCE here to get a call trace in case of a problem.
This facilitates finding the offending code part.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
