IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
USB2.0 PHY hangs in Rx Compliance test when the incoming packet
amplitude is varied below and above the Squelch Level of
Receiver during the active packet multiple times.
Version 1 of the controller allows PHY to be reset when RX fail condition
is detected to work around the above issue. This feature is
disabled by default and needs to be enabled using a bit from
the newly added PHYRST_CFG register. This patch enables the workaround.
There is no way to know controller version before device controller
is started and the workaround needs to be applied for both host and
device modes, so we rely on a DT property do decide when to
apply the workaround.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Controller version 0x0002450D has USB2 PHY RX sensitivity issues
that needs to be worked around by enabling phyrst-a-enable bit
in PHYRST_CFG register.
There is no way to know controller version before device controller
is started and the workaround needs to be applied for both host and
device modes, so we add this DT property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Converts cdns-usb3.txt to YAML schema cdns,usb3.yaml
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The Amlogic AXG is close to the GXL Glue but with a single OTG PHY.
It needs the same init sequence as GXL & GXM, but it seems it doesn't need
the host disconnect bit.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This switches the PCH UDC driver to use GPIO descriptors. The way
this is supposed to be used is confusing. The code contains the
following:
/* GPIO port for VBUS detecting */
static int vbus_gpio_port = -1; /* GPIO port number (-1:Not used) */
So a hardcoded GPIO number in the code. Further the probe() path
very clearly will exit if the GPIO is not found, so this driver
can only be configured by editing the code, hard-coding a GPIO
number into this variable.
This is simply not how we do things. My guess is that this is
used in products by patching a GPIO number into this variable and
shipping a kernel that is compile-time tailored for the target
system.
I switched this mechanism to using a GPIO descriptor associated
with the parent PCI device. This can be added by using the 16bit
subsystem ID or similar to identify which exact machine we are
running on and what GPIO is present on that machine, and then
add a GPIO descriptor using gpiod_add_lookup_table() from
<linux/gpio/machine.h>. Since I don't have any target systems
I cannot add this but I'm happy to help. I put in a FIXME so
the people actually using this driver knows what to do.
Cc: Felipe Balbi <balbi@kernel.org>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Introduce runtime PM and wakeup interrupt handler for cdns3,
the runtime PM is default off since other cdns3 may not
implement glue layer support for runtime PM.
One typical wakeup event use case is xHCI runtime suspend will clear
USBCMD.RS bit, after that the xHCI will not trigger any interrupts,
so its parent (cdns core device) needs to resume xHCI device when
any (wakeup) events occurs at host port.
When the controller is in low power mode, the lpm flag will be set.
The interrupt triggered later than lpm flag is set considers as
wakeup interrupt and handled at cdns_wakeup_irq. Once the wakeup
occurs, it first disables interrupt to avoid later interrupt
occurrence since the controller is in low power mode at that
time, and access registers may be invalid at that time. At wakeup
handler, it will call pm_request_resume to wakeup xHCI device, and
at runtime resume handler, it will enable interrupt again.
The API platform_suspend is introduced for glue layer to implement
platform specific PM sequence.
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Since we have both USB2 and USB3 PHYs for cdns3 controller, it is
better we have unity APIs to handle both USB2 and USB3's power, it
could simplify code for error handling and further power management
implementation.
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The Broadcom BDC driver did not have a MAINTAINERS entry which made it
escape review from Al and myself, add an entry so the relevant mailing
lists and people are copied.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Make debugging real problems easier by not trying to disable an EP that
was not yet enabled.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This is a follow-on patch for commit a23be4ed8f ("usb: gadget: aspeed:
improve vhub port irq handling"): for_each_set_bit() is replaced with
simple for() loop because for() loop runs faster on ASPEED BMC.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following sparse warning:
drivers/usb/dwc3/trace.c: note: in included file (through drivers/usb/dwc3/trace.h):
drivers/usb/dwc3/debug.h:374:39: warning: cast to non-scalar
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add interconnect support in dwc3-qcom driver to vote for bus
bandwidth.
This requires for two different paths - from USB to
DDR. The other is from APPS to USB.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The UDC NET2272 driver includes <linux/gpio.h> but does not
use any symbols from this file, so drop the include.
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The DPRAM memory from the USB High Speed Device Port (UDPHS) hardware
block was increased. This patch updates the endpoint allocation for sam9x60
to take advantage of this larger memory. At the same time the
constraint to allocate the endpoints in order was lifted. To handle old
and new hardware in the same driver the ep_prealloc was added.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Instead of trying to match every possible compatible use
of_find_matching_node_and_match() and pass the compatible array.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Call dwc2_debugfs_exit() and dwc2_hcd_remove() (if the HCD was enabled
earlier) when usb_add_gadget_udc() has failed. This ensures that the
debugfs entries created by dwc2_debugfs_init() as well as the HCD are
cleaned up in the error path.
Fixes: 207324a321 ("usb: dwc2: Postponed gadget registration to the udc class driver")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The user may have more information to override the HW parameter to
specify the maximum_speed. However, if the user specifies a
maximum_speed that the controller doesn't support, print out a warning.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the maximum_speed is not specified, default the device speed base on
its HW capability. Don't prematurely check HW capability before
validating the maximum_speed device property. The device property takes
precedence in dwc->maximum_speed.
Fixes: 0e1e5c47f7 ("usb: dwc3: add support for USB 2.0-only core configuration")
Reported-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
According the programming guide (for all DWC3 IPs), when the driver
handles ClearFeature(halt) request, it should issue CLEAR_STALL command
_after_ the END_TRANSFER command completes. The END_TRANSFER command may
take some time to complete. So, delay the ClearFeature(halt) request
control status stage and wait for END_TRANSFER command completion
interrupt. Only after END_TRANSFER command completes that the driver
may issue CLEAR_STALL command.
Cc: stable@vger.kernel.org
Fixes: cb11ea56f3 ("usb: dwc3: gadget: Properly handle ClearFeature(halt)")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The function driver may queue new requests right after halting the
endpoint (i.e. queue new requests while the endpoint is stalled).
There's no restriction preventing it from doing so. However, dwc3
currently drops those requests after CLEAR_STALL. The driver should only
drop started requests. Keep the pending requests in the pending list to
resume and process them after the host issues ClearFeature(Halt) to the
endpoint.
Cc: stable@vger.kernel.org
Fixes: cb11ea56f3 ("usb: dwc3: gadget: Properly handle ClearFeature(halt)")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Pull syscall tracing fix from Borislav Petkov:
"Fix the seccomp syscall rewriting so that trace and audit see the
rewritten syscall number, from Kees Cook"
* tag 'core_urgent_for_v5.9_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
core/entry: Report syscall correctly for trace and audit
Pull locking fixes from Borislav Petkov:
"Two fixes from the locking/urgent pile:
- Fix lockdep's detection of "USED" <- "IN-NMI" inversions (Peter
Zijlstra)
- Make percpu-rwsem operations on the semaphore's ->read_count
IRQ-safe because it can be used in an IRQ context (Hou Tao)"
* tag 'locking_urgent_for_v5.9_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/percpu-rwsem: Use this_cpu_{inc,dec}() for read_count
locking/lockdep: Fix "USED" <- "IN-NMI" inversions
Pull EFI fix from Borislav Petkov:
"Ensure that the EFI bootloader control module only probes successfully
on systems that support the EFI SetVariable runtime service"
[ Tag and commit from Ard Biesheuvel, forwarded by Borislav ]
* tag 'efi-urgent-for-v5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: efibc: check for efivars write capability
Pull x86 fixes from Borislav Petkov:
- A defconfig fix (Daniel Díaz)
- Disable relocation relaxation for the compressed kernel when not
built as -pie as in that case kernels built with clang and linked
with LLD fail to boot due to the linker optimizing some instructions
in non-PIE form; the gory details in the commit message (Arvind
Sankar)
- A fix for the "bad bp value" warning issued by the frame-pointer
unwinder (Josh Poimboeuf)
* tag 'x86_urgent_for_v5.9_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/unwind/fp: Fix FP unwinding in ret_from_fork
x86/boot/compressed: Disable relocation relaxation
x86/defconfigs: Explicitly unset CONFIG_64BIT in i386_defconfig
