IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit c244c092f1ed2acfb5af3d3da81e22367d3dd733 ]
This unexpected behavior is observed:
node 1 | node 2
------ | ------
link is established | link is established
reboot | link is reset
up | send discovery message
receive discovery message |
link is established | link is established
send discovery message |
| receive discovery message
| link is reset (unexpected)
| send reset message
link is reset |
It is due to delayed re-discovery as described in function
tipc_node_check_dest(): "this link endpoint has already reset
and re-established contact with the peer, before receiving a
discovery message from that node."
However, commit 598411d70f85 has changed the condition for calling
tipc_node_link_down() which was the acceptance of new media address.
This commit fixes this by restoring the old and correct behavior.
Fixes: 598411d70f85 ("tipc: make resetting of links non-atomic")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d463ac1acb454fafed58f695cb3067fbf489f3a0 ]
The fix commit the commit e4ea77f8e53f ("ALSA: usb-audio: Always apply
the hw constraints for implicit fb sync") tried to address the bug
where an incorrect PCM parameter is chosen when two (implicit fb)
streams are set up at the same time. This change had, however, some
side effect: once when the sync endpoint is chosen and set up, this
restriction is applied at the next hw params unless it's freed via hw
free explicitly.
This patch is a workaround for the problem by relaxing the hw
constraints a bit for the implicit fb sync. We still keep applying
the hw constraints for implicit fb sync, but only when the matching
sync EP is being used by other streams.
Fixes: e4ea77f8e53f ("ALSA: usb-audio: Always apply the hw constraints for implicit fb sync")
Reported-by: Ruud van Asseldonk <ruud@veniogames.com>
Link: https://lore.kernel.org/r/4e509aea-e563-e592-e652-ba44af6733fe@veniogames.com
Link: https://lore.kernel.org/r/20230102170759.29610-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0599313e26666e79f6e7fe1450588431b8cb25d5 ]
At the PCM hw params, we may re-configure the endpoints and it's done
by a temporary EP close followed by re-open. A potential problem
there is that the EP might be already running internally at the PCM
prepare stage; it's seen typically in the playback stream with the
implicit feedback sync. As this stream start isn't tracked by the
core PCM layer, we'd need to stop it explicitly, and that's the
missing piece.
This patch adds the stop_endpoints() call at snd_usb_hw_params() to
assure the stream stop before closing the EPs.
Fixes: bf6313a0ff76 ("ALSA: usb-audio: Refactor endpoint management")
Link: https://lore.kernel.org/r/4e509aea-e563-e592-e652-ba44af6733fe@veniogames.com
Link: https://lore.kernel.org/r/20230102170759.29610-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 472a6309c6467af89dbf660a8310369cc9cb041f ]
Restore volume after charge pump and PGA activation to ensure
that volume settings are correctly applied when re-enabling codec
from SND_SOC_BIAS_OFF state.
CLASS_W, CHARGE_PUMP and POWER_MANAGEMENT_2 register configuration
affect how the volume register are applied and must be configured first.
Fixes: a91eb199e4dc ("ASoC: Initial WM8904 CODEC driver")
Link: https://lore.kernel.org/all/c7864c35-738c-a867-a6a6-ddf9f98df7e7@gmail.com/
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221223080247.7258-1-francesco@dolcini.it
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a5665fc8d7a000671ebd3fe69c6f9acf1e0dcd9 ]
When SSU/enter hibern8 fail in WLUN suspend flow, trigger the error handler
and return busy to break the suspend. Otherwise the consumer will get
stuck in runtime suspend status.
Fixes: b294ff3e3449 ("scsi: ufs: core: Enable power management for wlun")
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Link: https://lore.kernel.org/r/20221208072520.26210-1-peter.wang@mediatek.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5675c381ea51360b4968b78f23aefda73e3de90d ]
Instead of locking and unlocking the clock scaling lock, surround the
command queueing code with an RCU reader lock and call synchronize_rcu().
This patch prepares for removal of the clock scaling lock.
Link: https://lore.kernel.org/r/20211203231950.193369-16-bvanassche@acm.org
Tested-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 1a5665fc8d7a ("scsi: ufs: core: WLUN suspend SSU/enter hibern8 fail recovery")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0a43ba6c66cc0688e2748d986a1459fdd3442ef ]
When Kconfig item CONFIG_SCSI_MPI3MR was introduced for mpi3mr driver, the
Makefile of the driver was not modified to refer the Kconfig item.
As a result, mpi3mr.ko is built regardless of the Kconfig item value y or
m. Also, if 'make localmodconfig' can not find the Kconfig item in the
Makefile, then it does not generate CONFIG_SCSI_MPI3MR=m even when
mpi3mr.ko is loaded on the system.
Refer to the Kconfig item to avoid the issues.
Fixes: c4f7ac64616e ("scsi: mpi3mr: Add mpi30 Rev-R headers and Kconfig")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20221207023659.2411785-1-shinichiro.kawasaki@wdc.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02228f6aa6a64d588bc31e3267d05ff184d772eb ]
If the system does not come from reset (like when it is kexec()), the
regulator might have an IRQ waiting for us.
If we enable the IRQ handler before its structures are ready, we crash.
This patch fixes:
[ 1.141839] Unable to handle kernel read from unreadable memory at virtual address 0000000000000078
[ 1.316096] Call trace:
[ 1.316101] blocking_notifier_call_chain+0x20/0xa8
[ 1.322757] cpu cpu0: dummy supplies not allowed for exclusive requests
[ 1.327823] regulator_notifier_call_chain+0x1c/0x2c
[ 1.327825] da9211_irq_handler+0x68/0xf8
[ 1.327829] irq_thread+0x11c/0x234
[ 1.327833] kthread+0x13c/0x154
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Adam Ward <DLG-Adam.Ward.opensource@dm.renesas.com>
Link: https://lore.kernel.org/r/20221124-da9211-v2-0-1779e3c5d491@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fe1f0714385fbcf76b0cbceb02b7277d842014fc upstream.
When the user moves a running task to a new rdtgroup using the task's
file interface or by deleting its rdtgroup, the resulting change in
CLOSID/RMID must be immediately propagated to the PQR_ASSOC MSR on the
task(s) CPUs.
x86 allows reordering loads with prior stores, so if the task starts
running between a task_curr() check that the CPU hoisted before the
stores in the CLOSID/RMID update then it can start running with the old
CLOSID/RMID until it is switched again because __rdtgroup_move_task()
failed to determine that it needs to be interrupted to obtain the new
CLOSID/RMID.
Refer to the diagram below:
CPU 0 CPU 1
----- -----
__rdtgroup_move_task():
curr <- t1->cpu->rq->curr
__schedule():
rq->curr <- t1
resctrl_sched_in():
t1->{closid,rmid} -> {1,1}
t1->{closid,rmid} <- {2,2}
if (curr == t1) // false
IPI(t1->cpu)
A similar race impacts rdt_move_group_tasks(), which updates tasks in a
deleted rdtgroup.
In both cases, use smp_mb() to order the task_struct::{closid,rmid}
stores before the loads in task_curr(). In particular, in the
rdt_move_group_tasks() case, simply execute an smp_mb() on every
iteration with a matching task.
It is possible to use a single smp_mb() in rdt_move_group_tasks(), but
this would require two passes and a means of remembering which
task_structs were updated in the first loop. However, benchmarking
results below showed too little performance impact in the simple
approach to justify implementing the two-pass approach.
Times below were collected using `perf stat` to measure the time to
remove a group containing a 1600-task, parallel workload.
CPU: Intel(R) Xeon(R) Platinum P-8136 CPU @ 2.00GHz (112 threads)
# mkdir /sys/fs/resctrl/test
# echo $$ > /sys/fs/resctrl/test/tasks
# perf bench sched messaging -g 40 -l 100000
task-clock time ranges collected using:
# perf stat rmdir /sys/fs/resctrl/test
Baseline: 1.54 - 1.60 ms
smp_mb() every matching task: 1.57 - 1.67 ms
[ bp: Massage commit message. ]
Fixes: ae28d1aae48a ("x86/resctrl: Use an IPI instead of task_work_add() to update PQR_ASSOC MSR")
Fixes: 0efc89be9471 ("x86/intel_rdt: Update task closid immediately on CPU in rmdir and unmount")
Signed-off-by: Peter Newman <peternewman@google.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/20221220161123.432120-1-peternewman@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e84077437902ec99eba0a6b516df772653f142c7 upstream.
Fix period calculation in case user sets a value of 1000. The input of
round_jiffies_relative() should be in jiffies and not in milli-seconds.
[ bp: Use the same code pattern as in edac_device_workq_setup() for
clarity. ]
Fixes: c4cf3b454eca ("EDAC: Rework workqueue handling")
Signed-off-by: Eliav Farber <farbere@amazon.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/20221020124458.22153-1-farbere@amazon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c6dd961d0c8e7e8f9fdc65071fb09ece702e18d upstream.
With 'GNU assembler (GNU Binutils for Debian) 2.39.90.20221231' the
build now reports:
arch/x86/realmode/rm/../../boot/bioscall.S: Assembler messages:
arch/x86/realmode/rm/../../boot/bioscall.S:35: Warning: found `movsd'; assuming `movsl' was meant
arch/x86/realmode/rm/../../boot/bioscall.S:70: Warning: found `movsd'; assuming `movsl' was meant
arch/x86/boot/bioscall.S: Assembler messages:
arch/x86/boot/bioscall.S:35: Warning: found `movsd'; assuming `movsl' was meant
arch/x86/boot/bioscall.S:70: Warning: found `movsd'; assuming `movsl' was meant
Which is due to:
PR gas/29525
Note that with the dropped CMPSD and MOVSD Intel Syntax string insn
templates taking operands, mixed IsString/non-IsString template groups
(with memory operands) cannot occur anymore. With that
maybe_adjust_templates() becomes unnecessary (and is hence being
removed).
More details: https://sourceware.org/bugzilla/show_bug.cgi?id=29525
Borislav Petkov further explains:
" the particular problem here is is that the 'd' suffix is
"conflicting" in the sense that you can have SSE mnemonics like movsD %xmm...
and the same thing also for string ops (which is the case here) so apparently
the agreement in binutils land is to use the always accepted suffixes 'l' or 'q'
and phase out 'd' slowly... "
Fixes: 7a734e7dd93b ("x86, setup: "glove box" BIOS calls -- infrastructure")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/Y71I3Ex2pvIxMpsP@hirez.programming.kicks-ass.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76d588dddc459fefa1da96e0a081a397c5c8e216 upstream.
Current imc-pmu code triggers a WARNING with CONFIG_DEBUG_ATOMIC_SLEEP
and CONFIG_PROVE_LOCKING enabled, while running a thread_imc event.
Command to trigger the warning:
# perf stat -e thread_imc/CPM_CS_FROM_L4_MEM_X_DPTEG/ sleep 5
Performance counter stats for 'sleep 5':
0 thread_imc/CPM_CS_FROM_L4_MEM_X_DPTEG/
5.002117947 seconds time elapsed
0.000131000 seconds user
0.001063000 seconds sys
Below is snippet of the warning in dmesg:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:580
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 2869, name: perf-exec
preempt_count: 2, expected: 0
4 locks held by perf-exec/2869:
#0: c00000004325c540 (&sig->cred_guard_mutex){+.+.}-{3:3}, at: bprm_execve+0x64/0xa90
#1: c00000004325c5d8 (&sig->exec_update_lock){++++}-{3:3}, at: begin_new_exec+0x460/0xef0
#2: c0000003fa99d4e0 (&cpuctx_lock){-...}-{2:2}, at: perf_event_exec+0x290/0x510
#3: c000000017ab8418 (&ctx->lock){....}-{2:2}, at: perf_event_exec+0x29c/0x510
irq event stamp: 4806
hardirqs last enabled at (4805): [<c000000000f65b94>] _raw_spin_unlock_irqrestore+0x94/0xd0
hardirqs last disabled at (4806): [<c0000000003fae44>] perf_event_exec+0x394/0x510
softirqs last enabled at (0): [<c00000000013c404>] copy_process+0xc34/0x1ff0
softirqs last disabled at (0): [<0000000000000000>] 0x0
CPU: 36 PID: 2869 Comm: perf-exec Not tainted 6.2.0-rc2-00011-g1247637727f2 #61
Hardware name: 8375-42A POWER9 0x4e1202 opal:v7.0-16-g9b85f7d961 PowerNV
Call Trace:
dump_stack_lvl+0x98/0xe0 (unreliable)
__might_resched+0x2f8/0x310
__mutex_lock+0x6c/0x13f0
thread_imc_event_add+0xf4/0x1b0
event_sched_in+0xe0/0x210
merge_sched_in+0x1f0/0x600
visit_groups_merge.isra.92.constprop.166+0x2bc/0x6c0
ctx_flexible_sched_in+0xcc/0x140
ctx_sched_in+0x20c/0x2a0
ctx_resched+0x104/0x1c0
perf_event_exec+0x340/0x510
begin_new_exec+0x730/0xef0
load_elf_binary+0x3f8/0x1e10
...
do not call blocking ops when !TASK_RUNNING; state=2001 set at [<00000000fd63e7cf>] do_nanosleep+0x60/0x1a0
WARNING: CPU: 36 PID: 2869 at kernel/sched/core.c:9912 __might_sleep+0x9c/0xb0
CPU: 36 PID: 2869 Comm: sleep Tainted: G W 6.2.0-rc2-00011-g1247637727f2 #61
Hardware name: 8375-42A POWER9 0x4e1202 opal:v7.0-16-g9b85f7d961 PowerNV
NIP: c000000000194a1c LR: c000000000194a18 CTR: c000000000a78670
REGS: c00000004d2134e0 TRAP: 0700 Tainted: G W (6.2.0-rc2-00011-g1247637727f2)
MSR: 9000000000021033 <SF,HV,ME,IR,DR,RI,LE> CR: 48002824 XER: 00000000
CFAR: c00000000013fb64 IRQMASK: 1
The above warning triggered because the current imc-pmu code uses mutex
lock in interrupt disabled sections. The function mutex_lock()
internally calls __might_resched(), which will check if IRQs are
disabled and in case IRQs are disabled, it will trigger the warning.
Fix the issue by changing the mutex lock to spinlock.
Fixes: 8f95faaac56c ("powerpc/powernv: Detect and create IMC device")
Reported-by: Michael Petlan <mpetlan@redhat.com>
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
[mpe: Fix comments, trim oops in change log, add reported-by tags]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230106065157.182648-1-kjain@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ea4b476cea1b7d461d16dda25ca3c7e616e2d15 upstream.
When first_ip is 0, last_ip is 0xFFFFFFFF, and netmask is 31, the value of
an arithmetic expression 2 << (netmask - mask_bits - 1) is subject
to overflow due to a failure casting operands to a larger data type
before performing the arithmetic.
Note that it's harmless since the value will be checked at the next step.
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
Fixes: b9fed748185a ("netfilter: ipset: Check and reject crazy /0 input parameters")
Signed-off-by: Ilia.Gavrilov <Ilia.Gavrilov@infotecs.ru>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87ca4f9efbd7cc649ff43b87970888f2812945b8 upstream.
Since commit 07ec77a1d4e8 ("sched: Allow task CPU affinity to be
restricted on asymmetric systems"), the setting and clearing of
user_cpus_ptr are done under pi_lock for arm64 architecture. However,
dup_user_cpus_ptr() accesses user_cpus_ptr without any lock
protection. Since sched_setaffinity() can be invoked from another
process, the process being modified may be undergoing fork() at
the same time. When racing with the clearing of user_cpus_ptr in
__set_cpus_allowed_ptr_locked(), it can lead to user-after-free and
possibly double-free in arm64 kernel.
Commit 8f9ea86fdf99 ("sched: Always preserve the user requested
cpumask") fixes this problem as user_cpus_ptr, once set, will never
be cleared in a task's lifetime. However, this bug was re-introduced
in commit 851a723e45d1 ("sched: Always clear user_cpus_ptr in
do_set_cpus_allowed()") which allows the clearing of user_cpus_ptr in
do_set_cpus_allowed(). This time, it will affect all arches.
Fix this bug by always clearing the user_cpus_ptr of the newly
cloned/forked task before the copying process starts and check the
user_cpus_ptr state of the source task under pi_lock.
Note to stable, this patch won't be applicable to stable releases.
Just copy the new dup_user_cpus_ptr() function over.
Fixes: 07ec77a1d4e8 ("sched: Allow task CPU affinity to be restricted on asymmetric systems")
Fixes: 851a723e45d1 ("sched: Always clear user_cpus_ptr in do_set_cpus_allowed()")
Reported-by: David Wang 王标 <wangbiao3@xiaomi.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221231041120.440785-2-longman@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 142e821f68cf5da79ce722cb9c1323afae30e185 upstream.
A clk, prepared and enabled in mtk_iommu_v1_hw_init(), is not released in
the error handling path of mtk_iommu_v1_probe().
Add the corresponding clk_disable_unprepare(), as already done in the
remove function.
Fixes: b17336c55d89 ("iommu/mediatek: add support for mtk iommu generation one HW")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/593e7b7d97c6e064b29716b091a9d4fd122241fb.1671473163.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcdb3ba7e2a8caae7bfefd603bc22fd0ce9a389c upstream.
In __alloc_and_insert_iova_range, there is an issue that retry_pfn
overflows. The value of iovad->anchor.pfn_hi is ~0UL, then when
iovad->cached_node is iovad->anchor, curr_iova->pfn_hi + 1 will
overflow. As a result, if the retry logic is executed, low_pfn is
updated to 0, and then new_pfn < low_pfn returns false to make the
allocation successful.
This issue occurs in the following two situations:
1. The first iova size exceeds the domain size. When initializing
iova domain, iovad->cached_node is assigned as iovad->anchor. For
example, the iova domain size is 10M, start_pfn is 0x1_F000_0000,
and the iova size allocated for the first time is 11M. The
following is the log information, new->pfn_lo is smaller than
iovad->cached_node.
Example log as follows:
[ 223.798112][T1705487] sh: [name:iova&]__alloc_and_insert_iova_range
start_pfn:0x1f0000,retry_pfn:0x0,size:0xb00,limit_pfn:0x1f0a00
[ 223.799590][T1705487] sh: [name:iova&]__alloc_and_insert_iova_range
success start_pfn:0x1f0000,new->pfn_lo:0x1efe00,new->pfn_hi:0x1f08ff
2. The node with the largest iova->pfn_lo value in the iova domain
is deleted, iovad->cached_node will be updated to iovad->anchor,
and then the alloc iova size exceeds the maximum iova size that can
be allocated in the domain.
After judging that retry_pfn is less than limit_pfn, call retry_pfn+1
to fix the overflow issue.
Signed-off-by: jianjiao zeng <jianjiao.zeng@mediatek.com>
Signed-off-by: Yunfei Wang <yf.wang@mediatek.com>
Cc: <stable@vger.kernel.org> # 5.15.*
Fixes: 4e89dce72521 ("iommu/iova: Retry from last rb tree node if iova search fails")
Acked-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20230111063801.25107-1-yf.wang@mediatek.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8a7b31d545d3a15f0e6f5984ae16f0ca4fd76aac ]
Since commit 0f0101719138 ("usb: dwc3: Don't switch OTG -> peripheral
if extcon is present") Dual Role support on Intel Merrifield platform
broke due to rearranging the call to dwc3_get_extcon().
It appears to be caused by ulpi_read_id() on the first test write failing
with -ETIMEDOUT. Currently ulpi_read_id() expects to discover the phy via
DT when the test write fails and returns 0 in that case, even if DT does not
provide the phy. As a result usb probe completes without phy.
Make ulpi_read_id() return -ETIMEDOUT to its user if the first test write
fails. The user should then handle it appropriately. A follow up patch
will make dwc3_core_init() set -EPROBE_DEFER in this case and bail out.
Fixes: ef6a7bcfb01c ("usb: ulpi: Support device discovery via DT")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ferry Toth <ftoth@exalondelft.nl>
Link: https://lore.kernel.org/r/20221205201527.13525-2-ftoth@exalondelft.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 869a99907faea6d1835b0bd0d0422ae3519c6ea9 ]
There is a race condition where mhi_prepare_channel() updates the
read and write pointers as the base address and in parallel, if
an M0 transition occurs, the tasklet goes ahead and rings
doorbells for all channels with a delta in TRE rings assuming
they are already enabled. This causes a null pointer access. Fix
it by adding a channel enabled check before ringing channel
doorbells.
Cc: stable@vger.kernel.org # 5.19
Fixes: a6e2e3522f29 "bus: mhi: core: Add support for PM state transitions"
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/1665889532-13634-1-git-send-email-quic_qianyu@quicinc.com
[mani: CCed stable list]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cb3e9864cdbe35ff6378966660edbcbac955fe17 upstream.
The total cork length created by ip6_append_data includes extension
headers, so we must exclude them when comparing them against the
IPV6_CHECKSUM offset which does not include extension headers.
Reported-by: Kyle Zeng <zengyhkyle@gmail.com>
Fixes: 357b40a18b04 ("[IPV6]: IPV6_CHECKSUM socket option can corrupt kernel memory")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b93fb4405fcb5112c5739c5349afb52ec7f15c07 upstream.
As the comment of pci_get_domain_bus_and_slot() says, it
returns a PCI device with refcount incremented, when finish
using it, the caller must decrement the reference count by
calling pci_dev_put().
In ixgbe_get_first_secondary_devfn() and ixgbe_x550em_a_has_mii(),
pci_dev_put() is called to avoid leak.
Fixes: 8fa10ef01260 ("ixgbe: register a mdiobus")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad75bd85b1db69c97eefea07b375567821f6ef58 upstream.
The 0x153 version of the kbd backlight control SNC handle has no separate
address to probe if the backlight is there.
This turns the probe call into a set keyboard backlight call with a value
of 0 turning off the keyboard backlight.
Skip probing when there is no separate probe address to avoid this.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1583752
Fixes: 800f20170dcf ("Keyboard backlight control for some Vaio Fit models")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mattia Dongili <malattia@linux.it>
Link: https://lore.kernel.org/r/20221213122943.11123-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2117773c839a8439a3771e0c040b5c505b083a7 upstream.
On some SoCs (hello SM6115) vcca-supply is not wired to any smd-rpm
or rpmh regulator, but instead powered by the VDD_MX line, which is
voted for in the DSI ctrl node.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 8fc939e72ff8 ("dt-bindings: msm: dsi: add yaml schemas for DSI PHY bindings")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/513555/
Link: https://lore.kernel.org/r/20221130135807.45028-1-konrad.dybcio@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef11cb7a29c0e13031c968190ea8f86104e7fb6a upstream.
On some SoCs (hello SM6350) vdds-supply is not wired to any smd-rpm
or rpmh regulator, but instead powered by the VDD_MX/mx.lvl line,
which is voted for in the DSI ctrl node.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Fixes: 8fc939e72ff8 ("dt-bindings: msm: dsi: add yaml schemas for DSI PHY bindings")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/511889/
Link: https://lore.kernel.org/r/20221116163218.42449-1-konrad.dybcio@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cba0d150fa102439114a91b3e215909efc9f169 upstream.
There are 3 possible interrupt sources are handled by DP controller,
HPDstatus, Controller state changes and Aux read/write transaction.
At every irq, DP controller have to check isr status of every interrupt
sources and service the interrupt if its isr status bits shows interrupts
are pending. There is potential race condition may happen at current aux
isr handler implementation since it is always complete dp_aux_cmd_fifo_tx()
even irq is not for aux read or write transaction. This may cause aux read
transaction return premature if host aux data read is in the middle of
waiting for sink to complete transferring data to host while irq happen.
This will cause host's receiving buffer contains unexpected data. This
patch fixes this problem by checking aux isr and return immediately at
aux isr handler if there are no any isr status bits set.
Current there is a bug report regrading eDP edid corruption happen during
system booting up. After lengthy debugging to found that VIDEO_READY
interrupt was continuously firing during system booting up which cause
dp_aux_isr() to complete dp_aux_cmd_fifo_tx() prematurely to retrieve data
from aux hardware buffer which is not yet contains complete data transfer
from sink. This cause edid corruption.
Follows are the signature at kernel logs when problem happen,
EDID has corrupt header
panel-simple-dp-aux aux-aea0000.edp: Couldn't identify panel via EDID
Changes in v2:
-- do complete if (ret == IRQ_HANDLED) ay dp-aux_isr()
-- add more commit text
Changes in v3:
-- add Stephen suggested
-- dp_aux_isr() return IRQ_XXX back to caller
-- dp_ctrl_isr() return IRQ_XXX back to caller
Changes in v4:
-- split into two patches
Changes in v5:
-- delete empty line between tags
Changes in v6:
-- remove extra "that" and fixed line more than 75 char at commit text
Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/516121/
Link: https://lore.kernel.org/r/1672193785-11003-2-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4b7f8febd4d9b615fbec2a06bf352b9c3729b11 upstream.
The Lenovo Legion 5 15ARH05 needs ideapad-laptop to call SALS_FNLOCK_ON /
SALS_FNLOCK_OFF on Fn-lock state change to get the LED in the Fn key to
correctly reflect the Fn-lock state.
Add a DMI match for the Legion 5 15ARH05 to the set_fn_lock_led_list[]
table for this.
Fixes: 81a5603a0f50 ("platform/x86: ideapad-laptop: Fix interrupt storm on fn-lock toggle on some Yoga laptops")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221215154357.123876-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6f033938beb31f893302a93f83ec0b6460c6cac upstream.
power-domain is required for the sc7180 dispcc GDSC but not every qcom SoC
has a similar dependency for example the apq8064.
Most Qcom SoC's using mdss-dsi-ctrl seem to have the ability to
power-collapse the MDP without collapsing DSI.
For example the qcom vendor kernel commit for apq8084, msm8226, msm8916,
msm8974.
7b5c011a77
"ARM: dts: msm: add mdss gdsc supply to dsi controller device
It is possible for the DSI controller to be active when MDP is
power collapsed. DSI controller needs to have it's own vote for
mdss gdsc to ensure that gdsc remains on in such cases."
This however doesn't appear to be the case for the apq8064 so we shouldn't
be marking power-domain as required in yaml checks.
Fixes: 4dbe55c97741 ("dt-bindings: msm: dsi: add yaml schemas for DSI bindings")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/515958/
Link: https://lore.kernel.org/r/20221223021025.1646636-3-bryan.odonoghue@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13ef096e342b00e30b95a90c6c13eee1f0bec4c5 upstream.
So far the adreno quirks have all been assigned with an OR operator,
which is problematic, because they were assigned consecutive integer
values, which makes checking them with an AND operator kind of no bueno..
Switch to using BIT(n) so that only the quirks that the programmer chose
are taken into account when evaluating info->quirks & ADRENO_QUIRK_...
Fixes: 370063ee427a ("drm/msm/adreno: Add A540 support")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/516456/
Link: https://lore.kernel.org/r/20230102100201.77286-1-konrad.dybcio@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1af7fef0d9d3fa075bf4e850f705df1fe97d33ce upstream.
Use KE_VSW instead of KE_SW for the SW_CAMERA_LENS_COVER key_entry
and get the value of the switch from the status field when handling
SW_CAMERA_LENS_COVER events, instead of always reporting 0.
Also correctly set the initial SW_CAMERA_LENS_COVER value.
Fixes: 8af9fa37b8a3 ("platform/x86: dell-privacy: Add support for Dell hardware privacy")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221221220724.119594-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae0fa0a3126a86c801c3220fcd8eefe03aa39f3e upstream.
It is possible that we (the host/kernel driver) receive command messages
that are not intended for us. Ignore those for now.
The whole story is a bit more complicated: It is possible to enable
debug output on SAM, which is sent via SSH command messages. By default
this output is sent to a debug connector, with its own target ID
(TID=0x03). It is possible to override the target of the debug output
and set it to the host/kernel driver. This, however, does not change the
original target ID of the message. Meaning, we receive messages with
TID=0x03 (debug) but expect to only receive messages with TID=0x00
(host).
The problem is that the different target ID also comes with a different
scope of request IDs. In particular, these do not follow the standard
event rules (i.e. do not fall into a set of small reserved values).
Therefore, current message handling interprets them as responses to
pending requests and tries to match them up via the request ID. However,
these debug output messages are not in fact responses, and therefore
this will at best fail to find the request and at worst pass on the
wrong data as response for a request.
Therefore ignore any command messages not intended for us (host) for
now. We can implement support for the debug messages once we have a
better understanding of them.
Note that this may also provide a bit more stability and avoid some
driver confusion in case any other targets want to talk to us in the
future, since we don't yet know what to do with those as well. A warning
for the dropped messages should suffice for now and also give us a
chance of discovering new targets if they come along without any
potential for bugs/instabilities.
Fixes: c167b9c7e3d6 ("platform/surface: Add Surface Aggregator subsystem")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20221202223327.690880-2-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6dc485f9940df8105ea729cbeb7a7d18d409dde5 upstream.
Unlike keys where userspace only reacts to keypresses, userspace may act
on switches in both (0 and 1) of their positions.
For example if a SW_TABLET_MODE switch is registered then GNOME will not
automatically show the onscreen keyboard when a text field gets focus on
touchscreen devices when SW_TABLET_MODE reports 0 and when SW_TABLET_MODE
reports 1 libinput will block (filter out) builtin keyboard and touchpad
events.
So to avoid unwanted side-effects EV_SW type inputs should only be
registered if they are actually present, only register SW_CAMERA_LENS_COVER
if it is actually there.
Fixes: 8af9fa37b8a3 ("platform/x86: dell-privacy: Add support for Dell hardware privacy")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221221220724.119594-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a152d05ae4a71d802d50cf9177dba34e8bb09f68 upstream.
If smb311 posix is enabled, we send the intended mode for file
creation in the posix create context. Instead of using what's there on
the stack, create the mfsymlink file with 0644.
Fixes: ce558b0e17f8a ("smb3: Add posix create context for smb3.11 posix mounts")
Cc: stable@vger.kernel.org
Signed-off-by: Volker Lendecke <vl@samba.org>
Reviewed-by: Tom Talpey <tom@talpey.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f8770c71646cf93abdf3fea8b7733aaec4c82a3 upstream.
Do it when parsing like in other actions instead of when
checking if goto is supported in current scenario.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Cc: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3de5616d36462a646f5b360ba82d3b09ff668eb upstream.
After applying an engine reset, on some platforms like Jasperlake, we
occasionally detect that the engine state is not cleared until shortly
after the resume. As we try to resume the engine with volatile internal
state, the first request fails with a spurious CS event (it looks like
it reports a lite-restore to the hung context, instead of the expected
idle->active context switch).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221212161338.1007659-1-andi.shyti@linux.intel.com
(cherry picked from commit 3db9d590557da3aa2c952f2fecd3e9b703dad790)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52531258318ed59a2dc5a43df2eaf0eb1d65438e upstream.
Userspace can guess the handle value and try to race GEM object creation
with handle close, resulting in a use-after-free if we dereference the
object after dropping the handle's reference. For that reason, dropping
the handle's reference must be done *after* we are done dereferencing
the object.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Chia-I Wu <olvaffe@gmail.com>
Fixes: 62fb7a5e1096 ("virtio-gpu: add 3d/virgl support")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221216233355.542197-2-robdclark@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3f360db08d55a14112bd27454e616a24296a8b0 upstream.
Make sure that *ptr__ within arch_this_cpu_to_op_simple() is only
dereferenced once by using READ_ONCE(). Otherwise the compiler could
generate incorrect code.
Cc: <stable@vger.kernel.org>
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82d3edb50a11bf3c5ef63294d5358ba230181413 upstream.
The current cmpxchg_double() loops within the perf hw sampling code do not
have READ_ONCE() semantics to read the old value from memory. This allows
the compiler to generate code which reads the "old" value several times
from memory, which again allows for inconsistencies.
For example:
/* Reset trailer (using compare-double-and-swap) */
do {
te_flags = te->flags & ~SDB_TE_BUFFER_FULL_MASK;
te_flags |= SDB_TE_ALERT_REQ_MASK;
} while (!cmpxchg_double(&te->flags, &te->overflow,
te->flags, te->overflow,
te_flags, 0ULL));
The compiler could generate code where te->flags used within the
cmpxchg_double() call may be refetched from memory and which is not
necessarily identical to the previous read version which was used to
generate te_flags. Which in turn means that an incorrect update could
happen.
Fix this by adding READ_ONCE() semantics to all cmpxchg_double()
loops. Given that READ_ONCE() cannot generate code on s390 which atomically
reads 16 bytes, use a private compare-and-swap-double implementation to
achieve that.
Also replace cmpxchg_double() with the private implementation to be able to
re-use the old value within the loops.
As a side effect this converts the whole code to only use bit fields
to read and modify bits within the hws trailer header.
Reported-by: Alexander Gordeev <agordeev@linux.ibm.com>
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Acked-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/linux-s390/Y71QJBhNTIatvxUT@osiris/T/#ma14e2a5f7aa8ed4b94b6f9576799b3ad9c60f333
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 000bca8d706d1bf7cca01af75787247c5a2fdedf upstream.
These indices should reference the ID placed within the dai_driver
array, not the indices of the array itself.
This fixes commit 4ff028f6c108 ("ASoC: qcom: lpass-cpu: Make I2S SD
lines configurable"), which among others, broke IPQ8064 audio
(sound/soc/qcom/lpass-ipq806x.c) because it uses ID 4 but we'd stop
initializing the mi2s_playback_sd_mode and mi2s_capture_sd_mode arrays
at ID 0.
Fixes: 4ff028f6c108 ("ASoC: qcom: lpass-cpu: Make I2S SD lines configurable")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20221231061545.2110253-1-computersforpeace@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2337a40e04dde1692b5b0a46ecc59f89aaba8a1 upstream.
This commit addresses the following erroneous situation with file-based
kdump executed on a system with a valid IPL report.
On s390, a kdump kernel, its initrd and IPL report if present are loaded
into a special and reserved on boot memory region - crashkernel. When
a system crashes and kdump was activated before, the purgatory code
is entered first which swaps the crashkernel and [0 - crashkernel size]
memory regions. Only after that the kdump kernel is entered. For this
reason, the pointer to an IPL report in lowcore must point to the IPL report
after the swap and not to the address of the IPL report that was located in
crashkernel memory region before the swap. Failing to do so, makes the
kdump's decompressor try to read memory from the crashkernel memory region
which already contains the production's kernel memory.
The situation described above caused spontaneous kdump failures/hangs
on systems where the Secure IPL is activated because on such systems
an IPL report is always present. In that case kdump's decompressor tried
to parse an IPL report which frequently lead to illegal memory accesses
because an IPL report contains addresses to various data.
Cc: <stable@vger.kernel.org>
Fixes: 99feaa717e55 ("s390/kexec_file: Create ipl report and pass to next kernel")
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf129830ee820f7fc90b98df193cd49d49344d09 upstream.
When a match has been made to the nth duplicate symbol, return
success not error.
Example:
Before:
$ cat file.c
cat: file.c: No such file or directory
$ cat file1.c
#include <stdio.h>
static void func(void)
{
printf("First func\n");
}
void other(void);
int main()
{
func();
other();
return 0;
}
$ cat file2.c
#include <stdio.h>
static void func(void)
{
printf("Second func\n");
}
void other(void)
{
func();
}
$ gcc -Wall -Wextra -o test file1.c file2.c
$ perf record -e intel_pt//u --filter 'filter func @ ./test' -- ./test
Multiple symbols with name 'func'
#1 0x1149 l func
which is near main
#2 0x1179 l func
which is near other
Disambiguate symbol name by inserting #n after the name e.g. func #2
Or select a global symbol by inserting #0 or #g or #G
Failed to parse address filter: 'filter func @ ./test'
Filter format is: filter|start|stop|tracestop <start symbol or address> [/ <end symbol or size>] [@<file name>]
Where multiple filters are separated by space or comma.
$ perf record -e intel_pt//u --filter 'filter func #2 @ ./test' -- ./test
Failed to parse address filter: 'filter func #2 @ ./test'
Filter format is: filter|start|stop|tracestop <start symbol or address> [/ <end symbol or size>] [@<file name>]
Where multiple filters are separated by space or comma.
After:
$ perf record -e intel_pt//u --filter 'filter func #2 @ ./test' -- ./test
First func
Second func
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.016 MB perf.data ]
$ perf script --itrace=b -Ftime,flags,ip,sym,addr --ns
1231062.526977619: tr strt 0 [unknown] => 558495708179 func
1231062.526977619: tr end call 558495708188 func => 558495708050 _init
1231062.526979286: tr strt 0 [unknown] => 55849570818d func
1231062.526979286: tr end return 55849570818f func => 55849570819d other
Fixes: 1b36c03e356936d6 ("perf record: Add support for using symbols in address filters")
Reported-by: Dmitrii Dolgov <9erthalion6@gmail.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dmitry Dolgov <9erthalion6@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230110185659.15979-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae9dcb91c6069e20b3b9505d79cbc89fd6e086f5 upstream.
Add timeout polling wait for auxiliary timestamps snapshot FIFO clear bit
(ATSFC) to clear. This is to ensure no residue fifo value is being read
erroneously.
Fixes: f4da56529da6 ("net: stmmac: Add support for external trigger timestamping")
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Noor Azura Ahmad Tarmizi <noor.azura.ahmad.tarmizi@intel.com>
Link: https://lore.kernel.org/r/20230111050200.2130-1-noor.azura.ahmad.tarmizi@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0283189e8f3d0917e2ac399688df85211f48447b upstream.
Sphinx 6.0 removed the execfile_() function, which we use as part of the
configuration process. They *did* warn us... Just open-code the
functionality as is done in Sphinx itself.
Tested (using SPHINX_CONF, since this code is only executed with an
alternative config file) on various Sphinx versions from 2.5 through 6.0.
Reported-by: Martin Liška <mliska@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3f450533bbcb6dd4d7d59cadc9b61b7321e4ac1 upstream.
Nathan reports that recent kernels built with LTO will crash when doing
EFI boot using Fedora's GRUB and SHIM. The culprit turns out to be a
misaligned load from the TPM event log, which is annotated with
READ_ONCE(), and under LTO, this gets translated into a LDAR instruction
which does not tolerate misaligned accesses.
Interestingly, this does not happen when booting the same kernel
straight from the UEFI shell, and so the fact that the event log may
appear misaligned in memory may be caused by a bug in GRUB or SHIM.
However, using READ_ONCE() to access firmware tables is slightly unusual
in any case, and here, we only need to ensure that 'event' is not
dereferenced again after it gets unmapped, but this is already taken
care of by the implicit barrier() semantics of the early_memunmap()
call.
Cc: <stable@vger.kernel.org>
Cc: Peter Jones <pjones@redhat.com>
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://github.com/ClangBuiltLinux/linux/issues/1782
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 561cafebb2cf97b0927b4fb0eba22de6200f682e upstream.
The following warning appears when executing:
make -C tools/testing/selftests/kvm
rseq_test.c: In function ‘main’:
rseq_test.c:237:33: warning: implicit declaration of function ‘gettid’; did you mean ‘getgid’? [-Wimplicit-function-declaration]
(void *)(unsigned long)gettid());
^~~~~~
getgid
/usr/bin/ld: /tmp/ccr5mMko.o: in function `main':
../kvm/tools/testing/selftests/kvm/rseq_test.c:237: undefined reference to `gettid'
collect2: error: ld returned 1 exit status
make: *** [../lib.mk:173: ../kvm/tools/testing/selftests/kvm/rseq_test] Error 1
Use the more compatible syscall(SYS_gettid) instead of gettid() to fix it.
More subsequent reuse may cause it to be wrapped in a lib file.
Signed-off-by: Jinrong Liang <cloudliang@tencent.com>
Message-Id: <20220802071240.84626-1-cloudliang@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bde971a83bbff78561458ded236605a365411b87 upstream.
Kernel build with clang and KCFLAGS=-fprofile-sample-use=<profile> fails with:
error: arch/arm64/kvm/hyp/nvhe/kvm_nvhe.tmp.o: Unexpected SHT_REL
section ".rel.llvm.call-graph-profile"
Starting from 13.0.0 llvm can generate SHT_REL section, see
https://reviews.llvm.org/rGca3bdb57fa1ac98b711a735de048c12b5fdd8086.
gen-hyprel does not support SHT_REL relocation section.
Filter out profile use flags to fix the build with profile optimization.
Signed-off-by: Denis Nikitin <denik@chromium.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221014184532.3153551-1-denik@chromium.org
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 406504c7b0405d74d74c15a667cd4c4620c3e7a9 upstream.
A recent development on the EFI front has resulted in guests having
their page tables baked in the firmware binary, and mapped into the
IPA space as part of a read-only memslot. Not only is this legitimate,
but it also results in added security, so thumbs up.
It is possible to take an S1PTW translation fault if the S1 PTs are
unmapped at stage-2. However, KVM unconditionally treats S1PTW as a
write to correctly handle hardware AF/DB updates to the S1 PTs.
Furthermore, KVM injects an exception into the guest for S1PTW writes.
In the aforementioned case this results in the guest taking an abort
it won't recover from, as the S1 PTs mapping the vectors suffer from
the same problem.
So clearly our handling is... wrong.
Instead, switch to a two-pronged approach:
- On S1PTW translation fault, handle the fault as a read
- On S1PTW permission fault, handle the fault as a write
This is of no consequence to SW that *writes* to its PTs (the write
will trigger a non-S1PTW fault), and SW that uses RO PTs will not
use HW-assisted AF/DB anyway, as that'd be wrong.
Only in the case described in c4ad98e4b72c ("KVM: arm64: Assume write
fault on S1PTW permission fault on instruction fetch") do we end-up
with two back-to-back faults (page being evicted and faulted back).
I don't think this is a case worth optimising for.
Fixes: c4ad98e4b72c ("KVM: arm64: Assume write fault on S1PTW permission fault on instruction fetch")
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Regression-tested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca88eeb308a221c2dcd4a64031d2e5fcd3db9eaa upstream.
The HP Spectre x360 13-aw0xxx devices use the ALC285 codec with GPIO 0x04
controlling the micmute LED and COEF 0x0b index 8 controlling the mute LED.
A quirk was added to make these work as well as a fixup.
Signed-off-by: Luka Guzenko <l.guzenko@web.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230110202514.2792-1-l.guzenko@web.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f680609bf1beac20e2a31ddcb1b88874123c39f upstream.
Turn on power early to avoid wrong state for power relation register.
This can earlier update JD state when resume back.
Signed-off-by: Yuchi Yang <yangyuchi66@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/e35d8f4fa18f4448a2315cc7d4a3715f@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
