IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
For the GS_USB_BREQ_DATA_BITTIMING USB control message the CANtact Pro
firmware uses a request value, which is already used by the
candleLight firmware for a different
purpose (GS_USB_BREQ_GET_USER_ID).
This patch adds a quirk to use the CANtact Pro's value for the
GS_USB_BREQ_DATA_BITTIMING USB control message instead of the official
one.
Link: https://lore.kernel.org/all/20220309124132.291861-18-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Introduce a workaround for a NXP chip errata on LPC546xx
controllers (Errata sheet LPC546xx / USB.15).
According to the document corruption can occur when the following
conditions are met:
* A TX (IN) transfer happens after a RX (OUT) transfer.
* The RX (OUT) transfer length is 4 + N * 16 (N >= 0) bytes.
Even though the struct gs_host_frame has a size of 76 bytes for a FD
frame, which does not apply to the above rule, corruption could be
seen.
Adding a dummy byte to break the second condition also on transfer
lengths with 4 + N * 8 bytes reliably circumvents USB transfer data
corruption.
The firmware can now request this quirk by setting
GS_CAN_FEATURE_REQ_USB_QUIRK_LPC546XX.
Link: https://lore.kernel.org/all/20220309124132.291861-17-mkl@pengutronix.de
Signed-off-by: Peter Fink <pfink@christ-es.de>
Signed-off-by: Christoph Möhring <cmoehring@christ-es.de>
Signed-off-by: Alexander Schartner <aschartner@christ-es.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CANtact Pro from Linklayer is the first gs_usb compatible device
supporting CAN-FD with a different HW and re-written candlelight FW.
Support for CAN-FD is indicated by the device setting the
GS_CAN_FEATURE_FD flag. CAN-FD support is requested by the driver with
the GS_CAN_MODE_FD flag. The CAN-FD specific data bit timing
parameters are set with the GS_USB_BREQ_DATA_BITTIMING control
message.
This patch is based on the Eric Evenchick's gs_usb_fd driver (which
itself is a fork of gs_usb). The gs_usb_fd code base was reintegrated
into the gs_usb driver, and reworked to not break the existing
classical-CAN only hardware.
Link: https://lore.kernel.org/all/20220309124132.291861-16-mkl@pengutronix.de
Link: https://github.com/linklayer/gs_usb_fd/issues/2
Co-developed-by: Eric Evenchick <eric@evenchick.com>
Signed-off-by: Eric Evenchick <eric@evenchick.com>
Signed-off-by: Peter Fink <pfink@christ-es.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Modify struct gs_host_frame to make use of a union and
DECLARE_FLEX_ARRAY to be able to store different data (lengths), which
will be added in later commits.
Store the gs_host_frame length in TX direction (host -> device) in
struct gs_can::hf_size_tx and RX direction (device -> host) in struct
gs_usb::hf_size_rx so it must be calculated only once.
Link: https://lore.kernel.org/all/20220309124132.291861-15-mkl@pengutronix.de
Signed-off-by: Peter Fink <pfink@christ-es.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some STM32G3 chips support up to 3 CAN-FD channels, increase number of
supported channels in this driver to 3 accordingly.
Link: https://lore.kernel.org/all/20220309124132.291861-14-mkl@pengutronix.de
Suggested-by: Ryan Edwards <ryan.edwards@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Introduce the variable udev in the gs_usb_probe() function to hold a
pointer to the struct usb_device. This avoids recalculating the value
several times in this function.
Link: https://lore.kernel.org/all/20220309124132.291861-13-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The widely used open source firmware candleLight has optional support
for reading/writing of an user defined value into the device's flash.
This is indicated by the GS_CAN_FEATURE_USER_ID feature. The
corresponding request are GS_USB_BREQ_GET_USER_ID and
GS_USB_BREQ_SET_USER_ID.
This patch documents these values.
Link: https://lore.kernel.org/all/20220309124132.291861-11-mkl@pengutronix.de
Link: 1453d70dc9
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the binary interface a feature bit might have a corresponding mode
bit (of the same value).
The GS_CAN_FEATURE_IDENTIFY feature doesn't come with a mode. Document
this, to avoid gaps when adding more features/modes later.
Link: https://lore.kernel.org/all/20220309124132.291861-10-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Newer versions of the widely used open source firmware candleLight
support hardware timestamps. The support is activated by setting the
GS_CAN_MODE_HW_TIMESTAMP in the GS_USB_BREQ_MODE request.
Although timestamp support is not yet supported by this driver, add
the missing bit for documentation purpose.
Link: https://lore.kernel.org/all/20220309124132.291861-9-mkl@pengutronix.de
Link: 44431f4a43
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Adds support for the CANFD IP variant in the V3U SoC.
Differences to controllers in other SoCs are limited to an increase in
the number of channels from two to eight, an absence of dedicated
registers for "classic" CAN mode, and a number of differences in magic
numbers (register offsets and layouts).
Inspired by BSP patch by Kazuya Mizuguchi.
Link: https://lore.kernel.org/all/20220309162609.3726306-2-uli+renesas@fpond.eu
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Function es58x_fd_rx_event() invokes the es58x_check_msg_len() macro:
| ret = es58x_check_msg_len(es58x_dev->dev, *rx_event_msg, msg_len);
While doing so, it dereferences an uninitialized
variable: *rx_event_msg.
This is actually harmless because es58x_check_msg_len() only uses
preprocessor macros (sizeof() and __stringify()) on
*rx_event_msg. c.f. [1].
Nonetheless, this pattern is confusing so the lines are reordered to
make sure that rx_event_msg is correctly initialized.
This patch also fixes a false positive warning reported by cppcheck:
| cppcheck possible warnings: (new ones prefixed by >>, may not be real problems)
|
| In file included from drivers/net/can/usb/etas_es58x/es58x_fd.c:
| >> drivers/net/can/usb/etas_es58x/es58x_fd.c:174:8: warning: Uninitialized variable: rx_event_msg [uninitvar]
| ret = es58x_check_msg_len(es58x_dev->dev, *rx_event_msg, msg_len);
| ^
[1] https://elixir.bootlin.com/linux/v5.16/source/drivers/net/can/usb/etas_es58x/es58x_core.h#L467
Link: https://lore.kernel.org/all/20220306101302.708783-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The vxcan driver provides a pair of virtual CAN interfaces to exchange
CAN traffic between different namespaces - analogue to veth.
In opposite to the vcan driver the local sent CAN traffic on this interface
is not echo'ed back but only sent to the remote peer. This is unusual and
can be easily fixed by removing IFF_ECHO from the netdevice flags that
are set for vxcan interfaces by default at startup.
Without IFF_ECHO set on driver level, the local sent CAN frames are echo'ed
in af_can.c in can_send(). This patch makes vxcan interfaces adopt the
same local echo behavior and procedures as known from the vcan interfaces.
Fixes: a8f820a380a2 ("can: add Virtual CAN Tunnel driver (vxcan)")
Link: https://lore.kernel.org/all/20220309120416.83514-5-socketcan@hartkopp.net
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With can_create_echo_skb() the skb which is forwarded to the peer CAN
interface shares the sk pointer from the originating socket.
This makes the CAN frame show up in the peer namespace as a TX packet.
With the use of skb_clone() analogue to the handling in gw.c the peer
skb gets a new start in the peer namespace and correctly appears as
a RX packet.
Link: https://lore.kernel.org/all/20220309120416.83514-4-socketcan@hartkopp.net
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The reason to extend the max PDU size from 4095 Byte (12 bit length value)
to a 32 bit value (up to 4 GByte) was to be able to flash 64 kByte
bootloaders with a single ISO-TP PDU. The max PDU size in the Linux kernel
implementation was set to 8200 Bytes to be able to test the length
information escape sequence.
It turns out that the demand for 64 kByte PDUs is real so the value for
MAX_MSG_LENGTH is set to 66000 to be able to potentially add some checksums
to the 65.536 Byte block.
Link: https://github.com/linux-can/can-utils/issues/347#issuecomment-1056142301
Link: https://lore.kernel.org/all/20220309120416.83514-3-socketcan@hartkopp.net
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The N_As value describes the time a CAN frame needs on the wire when
transmitted by the CAN controller. Even very short CAN FD frames need
arround 100 usecs (bitrate 1Mbit/s, data bitrate 8Mbit/s).
Having N_As to be zero (the former default) leads to 'no CAN frame
separation' when STmin is set to zero by the receiving node. This 'burst
mode' should not be enabled by default as it could potentially dump a high
number of CAN frames into the netdev queue from the soft hrtimer context.
This does not affect the system stability but is just not nice and
cooperative.
With this N_As/frame_txtime value the 'burst mode' is disabled by default.
As user space applications usually do not set the frame_txtime element
of struct can_isotp_options the new in-kernel default is very likely
overwritten with zero when the sockopt() CAN_ISOTP_OPTS is invoked.
To make sure that a N_As value of zero is only set intentional the
value '0' is now interpreted as 'do not change the current value'.
When a frame_txtime of zero is required for testing purposes this
CAN_ISOTP_FRAME_TXTIME_ZERO u32 value has to be set in frame_txtime.
Link: https://lore.kernel.org/all/20220309120416.83514-2-socketcan@hartkopp.net
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Instead of dumping the CAN frames into the netdevice queue the process to
transmit consecutive frames (CF) now waits for the frame to be transmitted
and therefore echo'ed from the CAN interface.
Link: https://lore.kernel.org/all/20220309120416.83514-1-socketcan@hartkopp.net
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use napi_alloc_skb to allocate memory when refilling the RX ring
in axienet_poll for more efficiency. napi_alloc_skb() can reuse
softirq-local cache of freed skbs which may still be cache-warm
and skipping allocator calls.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220308211013.1530955-1-robert.hancock@calian.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Back when tcp_tso_autosize() and TCP pacing were introduced,
our focus was really to reduce burst sizes for long distance
flows.
The simple heuristic of using sk_pacing_rate/1024 has worked
well, but can lead to too small packets for hosts in the same
rack/cluster, when thousands of flows compete for the bottleneck.
Neal Cardwell had the idea of making the TSO burst size
a function of both sk_pacing_rate and tcp_min_rtt()
Indeed, for local flows, sending bigger bursts is better
to reduce cpu costs, as occasional losses can be repaired
quite fast.
This patch is based on Neal Cardwell implementation
done more than two years ago.
bbr is adjusting max_pacing_rate based on measured bandwidth,
while cubic would over estimate max_pacing_rate.
/proc/sys/net/ipv4/tcp_tso_rtt_log can be used to tune or disable
this new feature, in logarithmic steps.
Tested:
100Gbit NIC, two hosts in the same rack, 4K MTU.
600 flows rate-limited to 20000000 bytes per second.
Before patch: (TSO sizes would be limited to 20000000/1024/4096 -> 4 segments per TSO)
~# echo 0 >/proc/sys/net/ipv4/tcp_tso_rtt_log
~# nstat -n;perf stat ./super_netperf 600 -H otrv6 -l 20 -- -K dctcp -q 20000000;nstat|egrep "TcpInSegs|TcpOutSegs|TcpRetransSegs|Delivered"
96005
Performance counter stats for './super_netperf 600 -H otrv6 -l 20 -- -K dctcp -q 20000000':
65,945.29 msec task-clock # 2.845 CPUs utilized
1,314,632 context-switches # 19935.279 M/sec
5,292 cpu-migrations # 80.249 M/sec
940,641 page-faults # 14264.023 M/sec
201,117,030,926 cycles # 3049769.216 GHz (83.45%)
17,699,435,405 stalled-cycles-frontend # 8.80% frontend cycles idle (83.48%)
136,584,015,071 stalled-cycles-backend # 67.91% backend cycles idle (83.44%)
53,809,530,436 instructions # 0.27 insn per cycle
# 2.54 stalled cycles per insn (83.36%)
9,062,315,523 branches # 137422329.563 M/sec (83.22%)
153,008,621 branch-misses # 1.69% of all branches (83.32%)
23.182970846 seconds time elapsed
TcpInSegs 15648792 0.0
TcpOutSegs 58659110 0.0 # Average of 3.7 4K segments per TSO packet
TcpExtTCPDelivered 58654791 0.0
TcpExtTCPDeliveredCE 19 0.0
After patch:
~# echo 9 >/proc/sys/net/ipv4/tcp_tso_rtt_log
~# nstat -n;perf stat ./super_netperf 600 -H otrv6 -l 20 -- -K dctcp -q 20000000;nstat|egrep "TcpInSegs|TcpOutSegs|TcpRetransSegs|Delivered"
96046
Performance counter stats for './super_netperf 600 -H otrv6 -l 20 -- -K dctcp -q 20000000':
48,982.58 msec task-clock # 2.104 CPUs utilized
186,014 context-switches # 3797.599 M/sec
3,109 cpu-migrations # 63.472 M/sec
941,180 page-faults # 19214.814 M/sec
153,459,763,868 cycles # 3132982.807 GHz (83.56%)
12,069,861,356 stalled-cycles-frontend # 7.87% frontend cycles idle (83.32%)
120,485,917,953 stalled-cycles-backend # 78.51% backend cycles idle (83.24%)
36,803,672,106 instructions # 0.24 insn per cycle
# 3.27 stalled cycles per insn (83.18%)
5,947,266,275 branches # 121417383.427 M/sec (83.64%)
87,984,616 branch-misses # 1.48% of all branches (83.43%)
23.281200256 seconds time elapsed
TcpInSegs 1434706 0.0
TcpOutSegs 58883378 0.0 # Average of 41 4K segments per TSO packet
TcpExtTCPDelivered 58878971 0.0
TcpExtTCPDeliveredCE 9664 0.0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Link: https://lore.kernel.org/r/20220309015757.2532973-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tcp_should_autocork() is evaluating if it makes senses
to not immediately send current skb, hoping that
user space will add more payload on it by the
time TCP stack reacts to upcoming TX completions.
If current skb got MSG_EOR mark, then we know
that no further data will be added, it is therefore
futile to wait.
SOF_TIMESTAMPING_TX_ACK will become a bit more accurate,
if prior packets are still in qdisc/device queues.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20220309054706.2857266-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
when CONFIG_SYSCTL not set, smc_sysctl_net_init/exit
need to be static inline to avoid missing-prototypes
if compile with W=1.
Since __net_exit has noinline annotation when CONFIG_NET_NS
not set, it should not be used with static inline.
So remove the __net_init/exit when CONFIG_SYSCTL not set.
Fixes: 7de8eb0d9039 ("net/smc: fix compile warning for smc_sysctl")
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220309033051.41893-1-dust.li@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dimitris Michailidis says:
====================
net/fungible: fix errors when CONFIG_TLS_DEVICE=n
This pair of patches fix compile errors in funeth when
CONFIG_TLS_DEVICE=n. The errors are due to symbols that are not defined
in this config but are used in code guarded by
"if (IS_ENABLED(CONFIG_TLS_DEVICE) ..."
One option is to place this code under preprocessor guards that will
keep the compiler from looking at the code. The option adopted here is
to define the offending symbols also when CONFIG_TLS_DEVICE=n.
The first patch does this for two functions in tls.h.
The second does the same for driver symbols and makes tls.h inclusion
unconditional.
====================
Link: https://lore.kernel.org/r/20220309034032.405212-1-dmichail@fungible.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Include the TLS headers unconditionally and define driver TLS symbols
used in code compiled also when CONFIG_TLS_DEVICE=n to fix the
following errors:
../drivers/net/ethernet/fungible/funeth/funeth_tx.c: In function ‘write_pkt_desc’:
../drivers/net/ethernet/fungible/funeth/funeth_tx.c:244:13: error: implicit declaration of function ‘tls_driver_ctx’ [-Werror=implicit-function-declaration]
244 | tls_ctx = tls_driver_ctx(skb->sk, TLS_OFFLOAD_CTX_DIR_TX);
| ^~~~~~~~~~~~~~
../drivers/net/ethernet/fungible/funeth/funeth_tx.c:244:37: error: ‘TLS_OFFLOAD_CTX_DIR_TX’ undeclared (first use in this function)
244 | tls_ctx = tls_driver_ctx(skb->sk, TLS_OFFLOAD_CTX_DIR_TX);
| ^~~~~~~~~~~~~~~~~~~~~~
../drivers/net/ethernet/fungible/funeth/funeth_tx.c:244:37: note: each undeclared identifier is reported only once for each function it appears in
../drivers/net/ethernet/fungible/funeth/funeth_tx.c:245:23: error: dereferencing pointer to incomplete type ‘struct fun_ktls_tx_ctx’
245 | tls->tlsid = tls_ctx->tlsid;
| ^~
../drivers/net/ethernet/fungible/funeth/funeth_tx.c: In function ‘fun_start_xmit’:
../drivers/net/ethernet/fungible/funeth/funeth_tx.c:310:6: error: implicit declaration of function ‘tls_is_sk_tx_device_offloaded’ [-Werror=implicit-function-declaration]
310 | tls_is_sk_tx_device_offloaded(skb->sk)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/net/ethernet/fungible/funeth/funeth_tx.c:311:9: error: implicit declaration of function ‘fun_tls_tx’; did you mean ‘fun_xdp_tx’? [-Werror=implicit-function-declaration]
311 | skb = fun_tls_tx(skb, q, &tls_len);
| ^~~~~~~~~~
| fun_xdp_tx
../drivers/net/ethernet/fungible/funeth/funeth_tx.c:311:7: warning: assignment to ‘struct sk_buff *’ from ‘int’ makes pointer from integer without a cast [-Wint-conversion]
311 | skb = fun_tls_tx(skb, q, &tls_len);
| ^
Fixes: db37bc177dae ("net/funeth: add the data path")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Having the definitions of {__,}tls_driver_ctx() under an #if
guard means code referencing them also needs to rely on the
preprocessor. The protection doesn't appear needed so make the
definitions unconditional.
Fixes: db37bc177dae ("net/funeth: add the data path")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts:
commit 02acd399533e ("bnxt_en: parse result field when NVRAM package install fails")
commit 22f5dba5065d ("bnxt_en: add an nvm test for hw diagnose")
commit bafed3f231f7 ("bnxt_en: implement hw health reporter")
These patches are still under discussion / I don't think they
are right, and since the authors don't reply promptly let me
lessen my load of "things I need to resolve before next release"
and revert them.
Acked-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20220308173659.304915-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If HW doesn't support PTP, then it doesn't support it. This is neither
a problem nor can the user do something about it. Therefore change the
message level to info.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/ee685745-f1ab-e9bf-f20e-077d55dff441@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is occasional suspend error from e1000e which blocks the
system from further suspending. And the issue was found on
a WhiskeyLake-U platform with I219-V:
[ 20.078957] PM: pci_pm_suspend(): e1000e_pm_suspend+0x0/0x780 [e1000e] returns -2
[ 20.078970] PM: dpm_run_callback(): pci_pm_suspend+0x0/0x170 returns -2
[ 20.078974] e1000e 0000:00:1f.6: PM: pci_pm_suspend+0x0/0x170 returned -2 after 371012 usecs
[ 20.078978] e1000e 0000:00:1f.6: PM: failed to suspend async: error -2
According to the code flow, this might be caused by broken MDI read/write
to PHY registers. However currently the code does not tell us which
register is broken. Thus enhance the debug information to print the
offender PHY register. So the next the issue is reproduced, this
information could be used for narrow down.
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reported-by: Todd Brandt <todd.e.brandt@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220308172030.451566-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rsmu (Renesas Synchronization Management Unit ) driver is located in
drivers/mfd and responsible for creating multiple devices including
idt82p33 phc, which will then use the exposed regmap and mutex
handle to access i2c/spi bus.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/1646748651-16811-1-git-send-email-min.li.xe@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This chips supports two ways to configure max MTU size:
- by setting SW_LEGAL_PACKET_DISABLE bit: if this bit is 0 allowed packed size
will be between 64 and bytes 1518. If this bit is 1, it will accept
packets up to 2000 bytes.
- by setting SW_JUMBO_PACKET bit. If this bit is set, the chip will
ignore SW_LEGAL_PACKET_DISABLE value and use REG_SW_MTU__2 register to
configure MTU size.
Current driver has disabled SW_JUMBO_PACKET bit and activates
SW_LEGAL_PACKET_DISABLE. So the switch will pass all packets up to 2000 without
any way to configure it.
By providing port_change_mtu we are switch to SW_JUMBO_PACKET way and will
be able to configure MTU up to ~9000.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220308135857.1119028-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When CONFIG_TCP_MD5SIG isn't enabled, there is a compilation bug due to
the fact that the static inline definition of tcp_inbound_md5_hash() has
an unexpected semicolon. Remove it.
Fixes: 1330b6ef3313 ("skb: make drop reason booleanable")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220309122012.668986-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 429c83c78ab2 ("dt-bindings: net: dsa: realtek: convert to YAML
schema, add MDIO") converts realtek-smi.txt to realtek.yaml, but missed to
adjust its reference in MAINTAINERS.
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about a
broken reference.
Repair this file reference in REALTEK RTL83xx SMI DSA ROUTER CHIPS.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The registers used to inject a frame to one of the ports is shared
between all the net devices. Therefore, there can be race conditions for
accessing the registers when two processes send frames at the same time
on different ports.
To fix this, add a spinlock around the function
'lan966x_port_ifh_xmit()'.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use min_t() in order to make code cleaner.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Rothwell reported the following failure on powerpc:
ERROR: modpost: ".local_memory_node"
[drivers/net/ethernet/fungible/funeth/funeth.ko] undefined!
AFAICS this is because local_memory_node() is a non-inline non-exported
function when CONFIG_HAVE_MEMORYLESS_NODES=y. It is also the wrong API
to get a CPU's memory node. Use cpu_to_mem() in the two spots it's used.
Fixes: ee6373ddf3a9 ("net/funeth: probing and netdev ops")
Fixes: db37bc177dae ("net/funeth: add the data path")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a number of cases where function returns drop/no drop
decision as a boolean. Now that we want to report the reason
code as well we have to pass extra output arguments.
We can make the reason code evaluate correctly as bool.
I believe we're good to reorder the reasons as they are
reported to user space as strings.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Incremental fixups for DSA unicast filtering
There are some bugs I've discovered in the recently merged "DSA unicast
filtering" series:
https://patchwork.kernel.org/project/netdevbpf/cover/20220302191417.1288145-1-vladimir.oltean@nxp.com/
First bug is the dereference of an uninitialized list (dp->fdbs) when
the "initial" tag protocol is placed in the device tree for the Felix
switch driver. This is a scenario I hadn't tested. It is handled by
patches 1-3.
Second bug is actually a sum of bugs that canceled each other out during
my previous testing. The MAC address change of a DSA slave interface
breaks termination for the other slave interfaces. But this actually
does not happen if the slave interface whose address is changing is
down. And even when up, traffic termination is still not broken because
we fail to properly disable host flooding. Patches 4-6 handle this for
the Felix driver (the only one benefiting from unicast filtering so far).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The Felix driver declares FDB isolation but puts all standalone ports in
VID 0. This is mostly problem-free as discussed with Alvin here:
https://patchwork.kernel.org/project/netdevbpf/cover/20220302191417.1288145-1-vladimir.oltean@nxp.com/#24763870
however there is one catch. DSA still thinks that FDB entries are
installed on the CPU port as many times as there are user ports, and
this is problematic when multiple user ports share the same MAC address.
Consider the default case where all user ports inherit their MAC address
from the DSA master, and then the user runs:
ip link set swp0 address 00:01:02:03:04:05
The above will make dsa_slave_set_mac_address() call
dsa_port_standalone_host_fdb_add() for 00:01:02:03:04:05 in port 0's
standalone database, and dsa_port_standalone_host_fdb_del() for the old
address of swp0, again in swp0's standalone database.
Both the ->port_fdb_add() and ->port_fdb_del() will be propagated down
to the felix driver, which will end up deleting the old MAC address from
the CPU port. But this is still in use by other user ports, so we end up
breaking unicast termination for them.
There isn't a problem in the fact that DSA keeps track of host
standalone addresses in the individual database of each user port: some
drivers like sja1105 need this. There also isn't a problem in the fact
that some drivers choose the same VID/FID for all standalone ports.
It is just that the deletion of these host addresses must be delayed
until they are known to not be in use any longer, and only the driver
has this knowledge. Since DSA keeps these addresses in &cpu_dp->fdbs and
&cpu_db->mdbs, it is just a matter of walking over those lists and see
whether the same MAC address is present on the CPU port in the port db
of another user port.
I have considered reusing the generic dsa_port_walk_fdbs() and
dsa_port_walk_mdbs() schemes for this, but locking makes it difficult.
In the ->port_fdb_add() method and co, &dp->addr_lists_lock is held, but
dsa_port_walk_fdbs() also acquires that lock. Also, even assuming that
we introduce an unlocked variant of the address iterator, we'd still
need some relatively complex data structures, and a void *ctx in the
dsa_fdb_walk_cb_t which we don't currently pass, such that drivers are
able to figure out, after iterating, whether the same MAC address is or
isn't present in the port db of another port.
All the above, plus the fact that I expect other drivers to follow the
same model as felix where all standalone ports use the same FID, made me
conclude that a generic method provided by DSA is necessary:
dsa_fdb_present_in_other_db() and the mdb equivalent. Felix calls this
from the ->port_fdb_del() handler for the CPU port, when the database
was classified to either a port db, or a LAG db.
For symmetry, we also call this from ->port_fdb_add(), because if the
address was installed once, then installing it a second time serves no
purpose: it's already in hardware in VID 0 and it affects all standalone
ports.
This change moves dsa_db_equal() from switch.c to dsa.c, since it now
has one more caller.
Fixes: 54c319846086 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two blamed commits were written/tested individually but not
together.
When put together, commit 90897569beb1 ("net: dsa: felix: start off with
flooding disabled on the CPU port"), which deletes a reinitialization of
PGID_UC/PGID_MC/PGID_BC, is no longer sufficient to ensure that these
port masks don't contain the CPU port module.
This is because commit b903a6bd2e19 ("net: dsa: felix: migrate flood
settings from NPI to tag_8021q CPU port") overwrites the hardware
default settings towards the CPU port module with the settings that used
to be present on the NPI port treated as a regular port. There, flooding
is enabled, so flooding would get enabled on the CPU port module too.
Adding conditional logic somewhere within felix_setup_tag_npi() to
configure either the default no-flood policy or the flood policy
inherited from the tag_8021q CPU port from a previous call to
dsa_port_manage_cpu_flood() is getting complicated. So just let the
migration logic do its thing during initial setup (which will
temporarily turn on flooding), then turn flooding off for the NPI port
after felix_set_tag_protocol() finishes. Here we are in felix_setup(),
so the DSA slave interfaces are not yet created, and this doesn't affect
traffic in any way.
Fixes: 90897569beb1 ("net: dsa: felix: start off with flooding disabled on the CPU port")
Fixes: b903a6bd2e19 ("net: dsa: felix: migrate flood settings from NPI to tag_8021q CPU port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
