IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 01f8902bcf3ff124d0aeb88a774180ebcec20ace ]
Fix hardware setup of multicast address hash:
- Never clear the hardware hash (to avoid packet loss)
- Construct the hash register values in software and then write once
to hardware
Signed-off-by: Rui Sousa <rui.sousa@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e2e004acc7cbe3c531e752a270a74e95cde3ea48 ]
This fixes a crash when running out of grant refs when creating many
queues across many netdevs.
* If creating queues fails (i.e. there are no grant refs available),
call xenbus_dev_fatal() to ensure that the xenbus device is set to the
closed state.
* If no queues are created, don't call xennet_disconnect_backend as
netdev->real_num_tx_queues will not have been set correctly.
* If setup_netfront() fails, ensure that all the queues created are
cleaned up, not just those that have been set up.
* If any queues were set up and an error occurs, call
xennet_destroy_queues() to clean up the napi context.
* If any fatal error occurs, unregister and destroy the netdev to avoid
leaving around a half setup network device.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0911d0041c22922228ca52a977d7b0b0159fee4b ]
Some ->page_mkwrite handlers may return VM_FAULT_RETRY as its return
code (GFS2 or Lustre can definitely do this). However VM_FAULT_RETRY
from ->page_mkwrite is completely unhandled by the mm code and results
in locking and writeably mapping the page which definitely is not what
the caller wanted.
Fix Lustre and block_page_mkwrite_ret() used by other filesystems
(notably GFS2) to return VM_FAULT_NOPAGE instead which results in
bailing out from the fault code, the CPU then retries the access, and we
fault again effectively doing what the handler wanted.
Link: http://lkml.kernel.org/r/20170203150729.15863-1-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 56d806222ace4c3aeae516cd7a855340fb2839d8 ]
sock_reset_flag() maps to __clear_bit() not the atomic version clear_bit().
Thus, we need smp_mb(), smp_mb__after_atomic() is not sufficient.
Fixes: 3c7151275c0c ("tcp: add memory barriers to write space paths")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Jason Baron <jbaron@akamai.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 91539eb1fda2d530d3b268eef542c5414e54bf1a ]
The static bug finder EBA (http://www.iagoabal.eu/eba/) reported the
following double-lock bug:
Double lock:
1. spin_lock_irqsave(pch->lock, flags) at pl330_free_chan_resources:2236;
2. call to function `pl330_release_channel' immediately after;
3. call to function `dma_pl330_rqcb' in line 1753;
4. spin_lock_irqsave(pch->lock, flags) at dma_pl330_rqcb:1505.
I have fixed it as suggested by Marek Szyprowski.
First, I have replaced `pch->lock' with `pl330->lock' in functions
`pl330_alloc_chan_resources' and `pl330_free_chan_resources'. This avoids
the double-lock by acquiring a different lock than `dma_pl330_rqcb'.
NOTE that, as a result, `pl330_free_chan_resources' executes
`list_splice_tail_init' on `pch->work_list' under lock `pl330->lock',
whereas in the rest of the code `pch->work_list' is protected by
`pch->lock'. I don't know if this may cause race conditions. Similarly
`pch->cyclic' is written by `pl330_alloc_chan_resources' under
`pl330->lock' but read by `pl330_tx_submit' under `pch->lock'.
Second, I have removed locking from `pl330_request_channel' and
`pl330_release_channel' functions. Function `pl330_request_channel' is
only called from `pl330_alloc_chan_resources', so the lock is already
held. Function `pl330_release_channel' is called from
`pl330_free_chan_resources', which already holds the lock, and from
`pl330_del'. Function `pl330_del' is called in an error path of
`pl330_probe' and at the end of `pl330_remove', but I assume that there
cannot be concurrent accesses to the protected data at those points.
Signed-off-by: Iago Abal <mail@iagoabal.eu>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 35e22e49a5d6a741ebe7f2dd280b2052c3003ef7 ]
In tipc_server_stop(), we iterate over the connections with limiting
factor as server's idr_in_use. We ignore the fact that this variable
is decremented in tipc_close_conn(), leading to premature exit.
In this commit, we iterate until the we have no connections left.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: John Thompson <thompa.atl@gmail.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0e73fc9a56f22f2eec4d2b2910c649f7af67b74d ]
The comparison on the timeout can lead to an array overrun
read on sctp_timer_tbl because of an off-by-one error. Fix
this by using < instead of <= and also compare to the array
size rather than SCTP_EVENT_TIMEOUT_MAX.
Fixes CoverityScan CID#1397639 ("Out-of-bounds read")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 11d8bcef7a0399e1d2519f207fd575fc404306b4 ]
DECON_TV requires STANDALONE_UPDATE after output enabling, otherwise it does
not start. This change is neutral for DECON.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c6180a6237174f481dc856ed6e890d8196b6f0fb ]
If the server reboots multiple times, the client should rely on the
server to tell it that it cannot reclaim state as per section 9.6.3.4
in RFC7530 and section 8.4.2.1 in RFC5661.
Currently, the client is being to conservative, and is assuming that
if the server reboots while state recovery is in progress, then it must
ignore state that was not recovered before the reboot.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63e41226afc3f7a044b70325566fa86ac3142538 ]
When a VCPU blocks (WFI) and has programmed the vtimer, we program a
soft timer to expire in the future to wake up the vcpu thread when
appropriate. Because such as wake up involves a vcpu kick, and the
timer expire function can get called from interrupt context, and the
kick may sleep, we have to schedule the kick in the work function.
The work function currently has a warning that gets raised if it turns
out that the timer shouldn't fire when it's run, which was added because
the idea was that in that case the work should never have been cancelled.
However, it turns out that this whole thing is racy and we can get
spurious warnings. The problem is that we clear the armed flag in the
work function, which may run in parallel with the
kvm_timer_unschedule->timer_disarm() call. This results in a possible
situation where the timer_disarm() call does not call
cancel_work_sync(), which effectively synchronizes the completion of the
work function with running the VCPU. As a result, the VCPU thread
proceeds before the work function completees, causing changes to the
timer state such that kvm_timer_should_fire(vcpu) returns false in the
work function.
All we do in the work function is to kick the VCPU, and an occasional
rare extra kick never harmed anyone. Since the race above is extremely
rare, we don't bother checking if the race happens but simply remove the
check and the clearing of the armed flag from the work function.
Reported-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4b09ec4b14a168bf2c687e1f598140c3c11e9222 ]
I have reports of a crash that look like __fput() was called twice for
a NFSv4.0 file. It seems possible that the state manager could try to
reclaim a lock and take a reference on the fl->fl_file at the same time the
file is being released if, during the close(), a signal interrupts the wait
for outstanding IO while removing locks which then skips the removal
of that lock.
Since 83bfff23e9ed ("nfs4: have do_vfs_lock take an inode pointer") has
removed the need to traverse fl->fl_file->f_inode in nfs4_lock_done(),
taking that reference is no longer necessary.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 18a3ed59d09cf81a6447aadf6931bf0c9ffec5e0 ]
Remove Rx overflow log messages as in an environment where logging results
in network traffic logging may cause further overflows.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[simon: reworked changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce7e40c432ba84da104438f6799d460a4cad41bc ]
ipddp_route structs contain alignment padding so kernel heap memory
is leaked when they are copied to user space in
ipddp_ioctl(SIOCFINDIPDDPRT). Change kmalloc() to kzalloc() to clear
that memory.
Signed-off-by: Vlad Tsyrklevich <vlad@tsyrklevich.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 93e246f783e6bd1bc64fdfbfe68b18161f69b28e ]
vti6 interface is registered before the rtnl_link_ops block
is attached. As a result the resulting RTM_NEWLINK is missing
IFLA_INFO_KIND. Re-order attachment of rtnl_link_ops block to fix.
Signed-off-by: Dave Forster <dforster@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 657279778af54f35e54b07b6687918f254a2992c ]
OMAP1510, OMAP5910 and OMAP310 have only 9 logical channels.
OMAP1610, OMAP5912, OMAP1710, OMAP730, and OMAP850 have 16 logical channels
available.
The wired 17 for the lch_count must have been used to cover the 16 + 1
dedicated LCD channel, in reality we can only use 9 or 16 channels.
The d->chan_count is not used by the omap-dma stack, so we can skip the
setup. chan_count was configured to the number of logical channels and not
the actual number of physical channels anyways.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 38e5a85562a6cd911fc26d951d576551a688574c ]
Inserting the TSB means adding an extra 8 bytes in front the of packet
that is going to be used as metadata information by the TDMA engine, but
stripped off, so it does not really help with the packet padding.
For some odd packet sizes that fall below the 60 bytes payload (e.g: ARP)
we can end-up padding them after the TSB insertion, thus making them 64
bytes, but with the TDMA stripping off the first 8 bytes, they could
still be smaller than 64 bytes which is required to ingress the switch.
Fix this by swapping the padding and TSB insertion, guaranteeing that
the packets have the right sizes.
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bb7da333d0a9f3bddc08f84187b7579a3f68fd24 ]
Since we need to pad our packets, utilize skb_put_padto() which
increases skb->len by how much we need to pad, allowing us to eliminate
the test on skb->len right below.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 22905582f6dd4bbd0c370fe5732c607452010c04 ]
Command perf test -v 16 (Setup struct perf_event_attr test) always
reports success even if the test case fails. It works correctly if you
also specify -F (for don't fork).
root@s35lp76 perf]# ./perf test -v 16
15: Setup struct perf_event_attr :
--- start ---
running './tests/attr/test-record-no-delay'
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.002 MB /tmp/tmp4E1h7R/perf.data
(1 samples) ]
expected task=0, got 1
expected precise_ip=0, got 3
expected wakeup_events=1, got 0
FAILED './tests/attr/test-record-no-delay' - match failure
test child finished with 0
---- end ----
Setup struct perf_event_attr: Ok
The reason for the wrong error reporting is the return value of the
system() library call. It is called in run_dir() file tests/attr.c and
returns the exit status, in above case 0xff00.
This value is given as parameter to the exit() function which can only
handle values 0-0xff.
The child process terminates with exit value of 0 and the parent does
not detect any error.
This patch corrects the error reporting and prints the correct test
result.
Signed-off-by: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com>
LPU-Reference: 20170913081209.39570-2-tmricht@linux.vnet.ibm.com
Link: http://lkml.kernel.org/n/tip-rdube6rfcjsr1nzue72c7lqn@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b00bebbc301c8e1f74f230dc82282e56b7e7a6db ]
When kernel configuration SMP,PREEMPT and DEBUG_PREEMPT are enabled,
echo 1 >/proc/sys/kernel/sysrq
echo p >/proc/sysrq-trigger
kernel will print call trace as below:
sysrq: SysRq : Show Regs
BUG: using __this_cpu_read() in preemptible [00000000] code: sh/435
caller is __this_cpu_preempt_check+0x18/0x20
Call trace:
[<ffffff8008088e80>] dump_backtrace+0x0/0x1d0
[<ffffff8008089074>] show_stack+0x24/0x30
[<ffffff8008447970>] dump_stack+0x90/0xb0
[<ffffff8008463950>] check_preemption_disabled+0x100/0x108
[<ffffff8008463998>] __this_cpu_preempt_check+0x18/0x20
[<ffffff80084c9194>] sysrq_handle_showregs+0x1c/0x40
[<ffffff80084c9c7c>] __handle_sysrq+0x12c/0x1a0
[<ffffff80084ca140>] write_sysrq_trigger+0x60/0x70
[<ffffff8008251e00>] proc_reg_write+0x90/0xd0
[<ffffff80081f1788>] __vfs_write+0x48/0x90
[<ffffff80081f241c>] vfs_write+0xa4/0x190
[<ffffff80081f3354>] SyS_write+0x54/0xb0
[<ffffff80080833f0>] el0_svc_naked+0x24/0x28
This can be seen on a common board like an r-pi3.
This happens because when echo p >/proc/sysrq-trigger,
get_irq_regs() is called outside of IRQ context,
if preemption is enabled in this situation,kernel will
print the call trace. Since many prior discussions on
the mailing lists have made it clear that get_irq_regs
either just returns NULL or stale data when used outside
of IRQ context,we simply avoid calling it outside of
IRQ context.
Signed-off-by: Jibin Xu <jibin.xu@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit da20ab35180780e4a6eadc804544f1fa967f3567 ]
We do not have tracepoints for sys_modify_ldt() because we define
it directly instead of using the normal SYSCALL_DEFINEx() macros.
However, there is a reason sys_modify_ldt() does not use the macros:
it has an 'int' return type instead of 'unsigned long'. This is
a bug, but it's a bug cemented in the ABI.
What does this mean? If we return -EINVAL from a function that
returns 'int', we have 0x00000000ffffffea in %rax. But, if we
return -EINVAL from a function returning 'unsigned long', we end
up with 0xffffffffffffffea in %rax, which is wrong.
To work around this and maintain the 'int' behavior while using
the SYSCALL_DEFINEx() macros, so we add a cast to 'unsigned int'
in both implementations of sys_modify_ldt().
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Brian Gerst <brgerst@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20171018172107.1A79C532@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0ab84da2e076948c49d36197ee7d254125c53eab ]
The upper four bits of the XR17V35x fractional divisor register (DLD)
control general chip function (RS-485 direction pin polarity, multidrop
mode, XON/XOFF parity check, and fast IR mode). Don't allow these bits
to be clobbered when setting the baudrate.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce035409bfa892a2fabb89720b542e1b335c3426 ]
If devm_extcon_dev_allocate() fails, we should disable clk before return.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 860d2686fda7 ("usb: phy: tahvo: Use devm_extcon_dev_[allocate|register]() and replace deprecated API")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3236a965486ba0c6043cf2c7b51943d8b382ae29 ]
This driver's ->rs485_config callback checks if SER_RS485_RTS_ON_SEND
and SER_RS485_RTS_AFTER_SEND have the same value. If they do, it means
the user has passed in invalid data with the TIOCSRS485 ioctl()
since RTS must have a different polarity when sending and when not
sending. In this case, rs485 mode is not enabled (the RS485_URA bit
is not set in the RS485 Enable Register) and this is supposed to be
signaled back to the user by clearing the SER_RS485_ENABLED bit in
struct serial_rs485 ... except a missing tilde character is preventing
that from happening.
Fixes: 28e3fb6c4dce ("serial: Add support for Fintek F81216A LPC to 4 UART")
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fec8f5ae1715a01c72ad52cb2ecd8aacaf142302 ]
We weren't testing the .limit and .limit_in_pages fields very well.
Add more tests.
This addition seems to trigger the "bits 16:19 are undefined" issue
that was fixed in an earlier patch. I think that, at least on my
CPU, the high nibble of the limit ends in LAR bits 16:19.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/5601c15ea9b3113d288953fd2838b18bedf6bc67.1509794321.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 48070c73058be6de9c0d754d441ed7092dfc8f12 ]
As of today QEMU does not provide the AIS facility to its guest. This
prevents Linux guests from using PCI devices as the ais facility is
checked during init. As this is just a performance optimization, we can
move the ais check into the code where we need it (calling the SIC
instruction). This is used at initialization and on interrupt. Both
places do not require any serialization, so we can simply skip the
instruction.
Since we will now get all interrupts, we can also avoid the 2nd scan.
As we can have multiple interrupts in parallel we might trigger spurious
irqs more often for the non-AIS case but the core code can handle that.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Acked-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ebe7c0a7be92bbd34c6ff5b55810546a0ee05bee ]
The hash_setup function always sets the hash_setup_done flag, even
when the hash algorithm is invalid. This prevents the default hash
algorithm defined as CONFIG_IMA_DEFAULT_HASH from being used.
This patch sets hash_setup_done flag only for valid hash algorithms.
Fixes: e7a2ad7eb6f4 "ima: enable support for larger default filedata hash algorithms"
Signed-off-by: Boshi Wang <wangboshi@huawei.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c654b21ede93845863597de9ad774fd30db5f2ab upstream.
Quectel BG96 is an Qualcomm MDM9206 based IoT modem, supporting both
CAT-M and NB-IoT. Tested hardware is BG96 mounted on Quectel
development board (EVB). The USB id is added to option.c to allow
DIAG,GPS,AT and modem communication with the BG96.
Signed-off-by: Sebastian Sjoholm <ssjoholm@mac.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d9047f8b967ce6181fd824ae922978e1b055cc0 upstream.
Free data structures required for runtime instrumentation from
arch_release_task_struct(). This allows to simplify the code a bit,
and also makes the semantics a bit easier: arch_release_task_struct()
is never called from the task that is being removed.
In addition this allows to get rid of exit_thread() in a later patch.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3bfd1300abfe3adb18e84a89d97a0e82a22124bb upstream.
This device will be used in future Amazon EC2 instances as the primary
serial port (i.e., data sent to this port will be available via the
GetConsoleOuput [1] EC2 API).
[1] http://docs.aws.amazon.com/AWSEC2/latest/APIReference/API_GetConsoleOutput.html
Signed-off-by: Matt Wilson <msw@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e43a12f1793ae1fe006e26fe9327a8840a92233c upstream.
KY-688 USB 3.1 Type-C Hub internally uses a Genesys Logic hub to connect
to Realtek r8153.
Similar to commit ("7496cfe5431f2 usb: quirks: Add no-lpm quirk for Moshi
USB to Ethernet Adapter"), no-lpm can make r8153 ethernet work.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fee72d5e8f1e7b8d8212e28291b1a0243ecf2f1 upstream.
We've been adding this as a quirk on a per device basis hoping that
newer disk enclosures would do better, but that has not happened,
so simply apply this quirk to all Seagate devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e393aa2446150536929140739f09c6ecbcbea7f0 upstream.
When we send a read request and hit the clean data in cache device, there
is a situation called cache read race in bcache(see the commit in the tail
of cache_look_up(), the following explaination just copy from there):
The bucket we're reading from might be reused while our bio is in flight,
and we could then end up reading the wrong data. We guard against this
by checking (in bch_cache_read_endio()) if the pointer is stale again;
if so, we treat it as an error (s->iop.error = -EINTR) and reread from
the backing device (but we don't pass that error up anywhere)
It should be noted that cache read race happened under normal
circumstances, not the circumstance when SSD failed, it was counted
and shown in /sys/fs/bcache/XXX/internal/cache_read_races.
Without this patch, when we use writeback mode, we will never reread from
the backing device when cache read race happened, until the whole cache
device is clean, because the condition
(s->recoverable && (dc && !atomic_read(&dc->has_dirty))) is false in
cached_dev_read_error(). In this situation, the s->iop.error(= -EINTR)
will be passed up, at last, user will receive -EINTR when it's bio end,
this is not suitable, and wield to up-application.
In this patch, we use s->read_dirty_data to judge whether the read
request hit dirty data in cache device, it is safe to reread data from
the backing device when the read request hit clean data. This can not
only handle cache read race, but also recover data when failed read
request from cache device.
[edited by mlyle to fix up whitespace, commit log title, comment
spelling]
Fixes: d59b23795933 ("bcache: only permit to recovery read error when cache device is clean")
Signed-off-by: Hua Rui <huarui.dev@gmail.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d59b23795933678c9638fd20c942d2b4f3cd6185 upstream.
When bcache does read I/Os, for example in writeback or writethrough mode,
if a read request on cache device is failed, bcache will try to recovery
the request by reading from cached device. If the data on cached device is
not synced with cache device, then requester will get a stale data.
For critical storage system like database, providing stale data from
recovery may result an application level data corruption, which is
unacceptible.
With this patch, for a failed read request in writeback or writethrough
mode, recovery a recoverable read request only happens when cache device
is clean. That is to say, all data on cached device is up to update.
For other cache modes in bcache, read request will never hit
cached_dev_read_error(), they don't need this patch.
Please note, because cache mode can be switched arbitrarily in run time, a
writethrough mode might be switched from a writeback mode. Therefore
checking dc->has_data in writethrough mode still makes sense.
Changelog:
V4: Fix parens error pointed by Michael Lyle.
v3: By response from Kent Oversteet, he thinks recovering stale data is a
bug to fix, and option to permit it is unnecessary. So this version
the sysfs file is removed.
v2: rename sysfs entry from allow_stale_data_on_failure to
allow_stale_data_on_failure, and fix the confusing commit log.
v1: initial patch posted.
[small change to patch comment spelling by mlyle]
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reported-by: Arne Wolf <awolf@lenovo.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Nix <nix@esperi.org.uk>
Cc: Kai Krakow <hurikhan77@gmail.com>
Cc: Eric Wheeler <bcache@lists.ewheeler.net>
Cc: Junhui Tang <tang.junhui@zte.com.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8a1a000555ecd1b824ac1ed6df8fe364dfbbbb0 upstream.
If nfsd4_process_open2() is initialising a new stateid, and yet the
call to nfs4_get_vfs_file() fails for some reason, then we must
declare the stateid closed, and unhash it before dropping the mutex.
Right now, we unhash the stateid after dropping the mutex, and without
changing the stateid type, meaning that another OPEN could theoretically
look it up and attempt to use it.
Reported-by: Andrew W Elble <aweits@rit.edu>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15ca08d3299682dc49bad73251677b2c5017ef08 upstream.
Open file stateids can linger on the nfs4_file list of stateids even
after they have been closed. In order to avoid reusing such a
stateid, and confusing the client, we need to recheck the
nfs4_stid's type after taking the mutex.
Otherwise, we risk reusing an old stateid that was already closed,
which will confuse clients that expect new stateids to conform to
RFC7530 Sections 9.1.4.2 and 16.2.5 or RFC5661 Sections 8.2.2 and 18.2.4.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c7245abda877d4689b3371db8ae2a4400d7d9ce upstream.
Move the state selection logic inside from the caller,
always making it return correct stp to use.
Signed-off-by: J . Bruce Fields <bfields@fieldses.org>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56350fb8978bbf4aafe08f21234e161dd128b417 upstream.
The hardware always writes one or two bytes in the index portion of
an indexed transfer. Make sure the message we send as the index
doesn't have a zero length.
Cc: Daniel Kurtz <djkurtz@chromium.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <seanpaul@chromium.org>
Fixes: 56f9eac05489 ("drm/i915/intel_i2c: use INDEX cycles for i2c read transactions")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123194157.25367-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit bb9e0d4bca50f429152e74a459160b41f3d60fb2)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae5c631e605a452a5a0e73205a92810c01ed954b upstream.
We can only specify the one slave address to indexed reads/writes.
Make sure the messages we check are destined to the same slave
address before deciding to do an indexed transfer.
Cc: Daniel Kurtz <djkurtz@chromium.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <seanpaul@chromium.org>
Fixes: 56f9eac05489 ("drm/i915/intel_i2c: use INDEX cycles for i2c read transactions")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123194157.25367-2-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit c4deb62d7821672265b87952bcd1c808f3bf3e8f)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b688741cb06695312f18b730653d6611e1bad28d upstream.
For correct close-to-open semantics, NFS must validate
the change attribute of a directory (or file) on open.
Since commit ecf3d1f1aa74 ("vfs: kill FS_REVAL_DOT by adding a
d_weak_revalidate dentry op"), open() of "." or a path ending ".." is
not revalidated reliably (except when that direct is a mount point).
Prior to that commit, "." was revalidated using nfs_lookup_revalidate()
which checks the LOOKUP_OPEN flag and forces revalidation if the flag is
set.
Since that commit, nfs_weak_revalidate() is used for NFSv3 (which
ignores the flags) and nothing is used for NFSv4.
This is fixed by using nfs_lookup_verify_inode() in
nfs_weak_revalidate(). This does the revalidation exactly when needed.
Also, add a definition of .d_weak_revalidate for NFSv4.
The incorrect behavior is easily demonstrated by running "echo *" in
some non-mountpoint NFS directory while watching network traffic.
Without this patch, "echo *" sometimes doesn't produce any traffic.
With the patch it always does.
Fixes: ecf3d1f1aa74 ("vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op")
cc: stable@vger.kernel.org (3.9+)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30863e38ebeb500a31cecee8096fb5002677dd9b upstream.
When mtdoops calls mtd_panic_write(), it eventually calls
panic_nand_write() in nand_base.c. In order to properly wait for the
nand chip to be ready in panic_nand_wait(), the chip must first be
selected.
When using the atmel nand flash controller, a panic would occur due to
a NULL pointer exception.
Fixes: 2af7c6539931 ("mtd: Add panic_write for NAND flashes")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brent Taylor <motobud@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3621a8eb59a913612c8e6e37d81f16b649f8b6c upstream.
During panel removal or system shutdown panel_simple_disable() is called
which disables the panel backlight but the panel is still powered due to
missing calls to panel_simple_unprepare().
Fixes: d02fd93e2cd8 ("drm/panel: simple - Disable panel on shutdown")
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170807115545.27747-1-net147@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f626a4ac8f57ddabf06d03870adab91e463217f upstream.
The function for byteswapping the data send to/from atombios was buggy for
num_bytes not divisible by four. The function must be aware of the fact
that after byte-swapping the u32 units, valid bytes might end up after the
num_bytes boundary.
This patch was tested on kernel 3.12 and allowed us to sucesfully use
DisplayPort on and Radeon SI card. Namely it fixed the link training and
EDID readout.
The function is patched both in radeon and amd drivers, since the functions
and the fixes are identical.
Signed-off-by: Roman Kapl <rka@sysgo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf33c1ee5254c6a430bc1538232b49c3ea13e613 upstream.
This patch try to fix the building error on MIPS. The reason is MIPS
has already defined the PTR macro, which conflicts with the PTR macro
in include/uapi/linux/bcache.h.
[fixed by mlyle: corrected a line-length issue]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9bcd462daf34aebb8de9ad7f76de0198bb5a0f0 upstream.
So far we completely rely on the caller to provide valid arguments.
To be on the safe side perform an own sanity check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebe7dd45cf49e3b49cacbaace17f9f878f21fbea upstream.
The block driver must be resumed if the mmc bus fails to suspend the card.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
