IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The driver wants to know the bit rate on the serial bus and takes that
to be the value set by 'set_sysclk'. The 'set_bclk_ratio' op is a better
fit for figuring out the clocking parameters of the serial bus, so
implement that and give it precedence over the prior methods.
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220915094444.11434-11-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The CS42L83 part is a headphone jack codec found in recent Apple
machines. It is a publicly undocumented part but as far as can be told
it is identical to CS42L42 except for two points:
* The chip ID is different.
* Of those registers for which we have a default value in the existing
CS42L42 kernel driver, one register (MCLK_CTL) differs in its reset
value on CS42L83.
To address those two points (and only those), add to the CS42L42 driver
a separate CS42L83 front.
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220915094444.11434-10-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Export the regmap callbacks for indicating readable/volatile registers,
also the range structure, to the CS42L42 core namespace. This is in
advance of reusing these bits in a CS42L83 driver frontend.
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220915094444.11434-9-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Split the I2C bus driver definition and probe()/remove() into a
separate module so that a SoundWire build of CS42L42 support does
not have a spurious dependency on I2C.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220915094444.11434-8-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
To prepare for adding SoundWire the probe must be split into three
parts:
1) The bus-specific probe
2) Common bus-agnostic probe steps
3) Initialization of the peripheral registers
Step (3) must be separate because on SoundWire devices the probe must
enable power supplies and release reset so that the peripheral can be
enumerated by the bus, but it isn't possible to access registers until
enumeration has completed.
The call to devm_snd_soc_register_component() must be done at stage (2)
so that it can EPROBE_DEFER if necessary. In SoundWire systems stage (3)
is not a probe event so a deferral at this stage would not result in
re-probing dependencies.
A new init_done flag indicates that the chip has been identified and
initialized. This is used to prevent cs42l42_remove(), cs42l42_suspend(),
cs42l42_restore() and cs42l42_irq_thread() from attempting register
accesses if the chip was not successfully initialized. Although this
cannot happen on I2C, because the entire probe would fail, it is
possible on SoundWire if probe succeeds but the cs42l42 is never
enumerated.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220915094444.11434-5-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Clean up the handling of bitclock frequency by keeping all the logic
in cs42l42_pcm_hw_params(), which then simply passes the frequency as
an argument to cs42l42_pll_config().
The previous code had become clunky as a legacy of earlier versions of
the clock handling. The logic was split across cs42l42_pcm_hw_params()
and cs42l42_pll_config(), with the params-derived bclk stashed in
struct cs42l42_private only to pass it to cs42l42_pll_config().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220915094444.11434-3-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Make cs42l42.h include the other headers it depends on instead of
assuming that the .c file already included them.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220817122347.1356773-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is to allow the hda driver to have access to the register names,
for improved maintainability.
Also ensure new header is aligned to 100 columns.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220504161236.2490532-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
DETECT_MODE and PLL_START must be zero while HP_PDN and ADC_PDN are
both 1. If this condition is broken it can discharge FILT+ and it
can then take up to 1 second for FILT+ to recharge.
There is no workaround required for this, simply avoiding settings
and sequences that would break the requirement. The driver already
meets the requirement.
But it is not obvious from reading the code that this requirement
exists, or what is ensuring it is met. So it would not currently be
obvious to someone changing the code that there is certain special
behaviour that must be maintained.
To avoid accidental breakage in the future:
- Add comments into the register definitions to warn about this so
that anyone changing the code around DETECT_MODE and PLL_START is
aware of this requirement.
- Add a comment where PLL_START is written to 1 to highlight the
requirement and why it is satisfied.
- Add a comment in cs42l42_setup_hs_type_detect() when DETECT_MODE is
initialized.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220304144015.398656-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add system suspend functions to handle clean power-down on suspend and
restoring registers on resume.
The jack state could change during suspend. Plug->unplug and unplug->plug
are straightforward because this looks no different from any other plug
state change - there will be a plugged or unplugged interrupt pending.
The jack could be unplugged and a different type of jack plugged, and on
resume the plug state would not have changed. Setting plug_state back to
TS_TRANS (transitioning) will make the next plug interrupt after resume
run a type detection.
During system suspend any jack plug/unplug and button events will not be
reported or generate a system wakeup. If the plug state or headset type
has changed it will be reported after resume.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220121120412.672284-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename jack_detect_mutex to irq_lock and make it lock the entire IRQ
handling.
The jack_detect_mutex was introduced to synchronize registering an
ALSA jack handler, via cs42l42_set_jack(), with the jack state
processing in the IRQ handler, and was taken only around the
relevant part of the IRQ handling code.
System suspend will need to synchronize with the IRQ handler thread
so will need a similar mutex that surrounds all of the IRQ handling.
Repurposing the existing jack_detect_mutex is the simplest option.
It does no harm for a call to cs42l42_set_jack() to additionally
block the first few lines of IRQ handling, and the only interrupts
used by the driver are all for jack handling.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220121120412.672284-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When a jack handler is registered in cs42l42_set_jack() the
initial state should be reported if an attached headphone/headset
has already been detected.
The jack detect sequence takes around 1 second: typically long
enough for the machine driver to probe and register the jack handler
in time to receive the first report from the interrupt handler. So
it is possible on some systems that the correct initial state was seen
simply because of lucky timing. Modular builds were more likely to
miss the reporting of the initial state.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 4ca239f33737 ("ASoC: cs42l42: Always enable TS_PLUG and TS_UNPLUG interrupts")
Link: https://lore.kernel.org/r/20211119124854.58939-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that struct cs42l42_private has pll_config, the current PLL
configuration can be looked up directly in pll_ratio_table. This
makes the pll_divout member of cs42l42_private redundant since it
was only a copy of the value from pll_ratio_table.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211116163901.45390-5-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds an ALSA control so that the slow-start audio ramp feature
can be disabled. This is useful for high-definition audio applications.
The register field is unusual in that it is a 3-bit field with only
two valid values, 000=off and 111=on.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211101101006.13092-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The interrupt handling code was getting the struct device* from a
struct snd_soc_component* stored in struct cs42l42_private. If the
interrupt was asserted before ASoC calls component_probe() the
snd_soc_component* will be NULL.
The stored snd_soc_component* is not actually used for anything other
than indirectly getting the struct device*. Remove it, and store the
struct device* in struct cs42l42_private.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211025112258.9282-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the datasheet the SRC MCLK must be as near as possible to
(125 * sample rate). This means it should be ~6MHz for rates up to 48k
and ~12MHz for rates above that. As per datasheet table 4-21.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-14-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After enabling the HP or ADC by writing the corresponding PDN=0,
it takes around 20 milliseconds for it to power up and the midrail
supply to be stable. Add this wait into a DAPM widget callback.
If HP and ADC are both powering up in a DAPM sequence, there's no
need to do the wait twice. The widget will perform one wait in the
POST_PMU if there was a PRE_PMU for one or both.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-13-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some headsets require very different comparator thresholds for type detection,
as well as longer settling times. In order to detect a larger number of headsets,
use 2 thresholds to give maximum coverage (1.25V and 1.75V), as well as a longer
settling time of 100ms. This will not affect default audotodetect mode
and applies to manual mode type detection only.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210927111437.18113-1-vitalyr@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some headsets are not detected correctly by Automatic Type Detection
on cs42l42. Instead, Manual Type Detection can be used to give a
more accurate value.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210916102750.9212-2-vitalyr@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Quite a lot of fixes here, the biggest set being for the cs42l42 driver
which is reasonably old but has seen a sudden uptick in activity.
There's also some fixes for correctly referencing PCM buffer addresses
and the removal of some driver-local bodges that had been done for the
lack of prefix handling in DAPM which were broken by the core handling
that as expected.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmENS7kACgkQJNaLcl1U
h9AxAgf/RDnVYb2b77qhUbHva/5fOUQMCx6NMWQ79LG8rRU2cZ5f+NxJtLKNOQIQ
A05mH0Y4BCQFeCKWN/JpGlJWITUpBLhYIxBe//5URjzkds8h8KCfkxc+UGxYxy/h
xPrXztFRMRD74kQKwpISLxM134qRW0j3fONSAxXwWSmamL2UEefohVX+edsHgl37
vdJNMiBfq8g9fCIq5nT/Il7yNBlEosLoB1UxBpMRElMa+y5ZuYRjl2R8n0CIIbHG
kER2ilNY7ldU1cs+KPbbXcfRrDc3BUs2/eNNSljqJb7XK4pJGndpEKX2i/Bzi5i0
BfPcN7VIm4fG79GbJ/Xw+hsOcA58YA==
=r49k
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.14-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.14
Quite a lot of fixes here, the biggest set being for the cs42l42 driver
which is reasonably old but has seen a sudden uptick in activity.
There's also some fixes for correctly referencing PCM buffer addresses
and the removal of some driver-local bodges that had been done for the
lack of prefix handling in DAPM which were broken by the core handling
that as expected.
I2S always has two LRCLK phases and both CH1 and CH2 of the RX
must be enabled (corresponding to the low and high phases of LRCLK.)
The selection of the valid data channels is done by setting the DAC
CHA_SEL and CHB_SEL. CHA_SEL is always the first (left) channel,
CHB_SEL depends on the number of active channels.
Previously for mono ASP CH2 was not enabled, the result was playing
mono data would not produce any audio output.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 621d65f3b868 ("ASoC: cs42l42: Provide finer control on playback path")
Link: https://lore.kernel.org/r/20210805161111.10410-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Both SCLK and PLL clocks must be running to drive the glitch-free mux
behind MCLK_SRC_SEL and complete the switchover.
This patch moves the writing of MCLK_SRC_SEL to when the PLL is started
and stopped, so that it only transitions while the PLL is running.
The unconditional write MCLK_SRC_SEL=0 in cs42l42_mute_stream() is safe
because if the PLL is not running MCLK_SRC_SEL is already 0.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 43fc357199f9 ("ASoC: cs42l42: Set clock source for both ways of stream")
Link: https://lore.kernel.org/r/20210805161111.10410-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The definition of CS42L42_ADC_PDN_MASK was incorrectly defined
as the HP_PDN bit.
Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210616135604.19363-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The 16 Bits, 2 channels, 48K sample rate use case needs
to configure a safer pll_divout during the start of PLL
After 800us from the start of PLL the correct pll_divout
can be set
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Message-Id: <20210525090822.64577-1-tanureal@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
HSBIAS_SENSE_EN configures HSBIAS output current sense through
the external 2.21-k resistor. HSBIAS_SENSE is hardware feature to reduce
the potential pop noise during the headset plug out slowly. But on some
platforms ESD voltage will affect it causing test to fail, especially
with CTIA headset type. For different hardware setups, a designer might
want to tweak default behavior.
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210511145220.125760-1-vitalyr@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the internal jack creation by set_jack call, so users can map
buttons in their machine driver
Also only enable jack detection IRQ after set_jack call
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210426155303.853236-1-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There must be a delay of at least 150us after writing SCLK_PRESENT
before issuing another I2C write.
This is done using struct reg_sequence because it can specify a delay
after the write and the whole sequence is written atomically.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210306185553.62053-14-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for reading the source clock from snd_soc_params_to_bclk
so the machine driver is not required to call cs42l42_set_sysclk
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210306185553.62053-13-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Report the Jack events to the user space through ALSA.
Also moves request_threaded_irq() to component_probe so it don't get
interrupts before the initialization the struct snd_soc_jack.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210306185553.62053-12-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This delay is part of the power-up sequence defined in the datasheet.
A runtime_resume is a power-up so must also include the delay.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210305173442.195740-6-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver was setting bit clock polarity opposite to intended polarity.
Also simplify the code by grouping ADC and DAC clock configurations into
a single field.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210305173442.195740-2-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Cirrus Logic CS42L42 codec. SoundWire support
is not enabled. Features support for I2C control and I2S audio.
Signed-off-by: James Schulman <james.schulman@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
