IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 3c89c70634bb0b6f48512de873e7a45c7e1fbaa5 ]
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/pinctrl-rockchip.c:3221:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3196, but without a corresponding object release within this function.
./drivers/pinctrl/pinctrl-rockchip.c:3223:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3196, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-gpio@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35240ba26a932b279a513f66fa4cabfd7af55221 ]
Current calculator doesn't do it' job quite correct. First of all the
max310x baud-rates generator supports the divisor being less than 16.
In this case the x2/x4 modes can be used to double or quadruple
the reference frequency. But the current baud-rate setter function
just filters all these modes out by the first condition and setups
these modes only if there is a clocks-baud division remainder. The former
doesn't seem right at all, since enabling the x2/x4 modes causes the line
noise tolerance reduction and should be only used as a last resort to
enable a requested too high baud-rate.
Finally the fraction is supposed to be calculated from D = Fref/(c*baud)
formulae, but not from D % 16, which causes the precision loss. So to speak
the current baud-rate calculator code works well only if the baud perfectly
fits to the uart reference input frequency.
Lets fix the calculator by implementing the algo fully compliant with
the fractional baud-rate generator described in the datasheet:
D = Fref / (c*baud), where c={16,8,4} is the x1/x2/x4 rate mode
respectively, Fref - reference input frequency. The divisor fraction is
calculated from the same formulae, but making sure it is found with a
resolution of 0.0625 (four bits).
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 561759292774707b71ee61aecc07724905bb7ef1 ]
If the device rejects the control transfer to enable device-initiated
U1/U2 entry, then the device will not initiate U1/U2 transition. To
improve the performance, the downstream port should not initate
transition to U1/U2 to avoid the delay from the device link command
response (no packet can be transmitted while waiting for a response from
the device). If the device has some quirks and does not implement U1/U2,
it may reject all the link state change requests, and the downstream
port may resend and flood the bus with more requests. This will affect
the device performance even further. This patch disables the
hub-initated U1/U2 if the device-initiated U1/U2 entry fails.
Reference: USB 3.2 spec 7.2.4.2.3
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b2d4dcf71c4a91b420f835e52ddea8192300a3b ]
Since commit 10a68cdf10 (nfsd: fix performance-limiting session
calculation) (Linux 5.1-rc1 and 4.19.31), shares from NFS servers with
1 TB of memory cannot be mounted anymore. The mount just hangs on the
client.
The gist of commit 10a68cdf10 is the change below.
-avail = clamp_t(int, avail, slotsize, avail/3);
+avail = clamp_t(int, avail, slotsize, total_avail/3);
Here are the macros.
#define min_t(type, x, y) __careful_cmp((type)(x), (type)(y), <)
#define clamp_t(type, val, lo, hi) min_t(type, max_t(type, val, lo), hi)
`total_avail` is 8,434,659,328 on the 1 TB machine. `clamp_t()` casts
the values to `int`, which for 32-bit integers can only hold values
−2,147,483,648 (−2^31) through 2,147,483,647 (2^31 − 1).
`avail` (in the function signature) is just 65536, so that no overflow
was happening. Before the commit the assignment would result in 21845,
and `num = 4`.
When using `total_avail`, it is causing the assignment to be
18446744072226137429 (printed as %lu), and `num` is then 4164608182.
My next guess is, that `nfsd_drc_mem_used` is then exceeded, and the
server thinks there is no memory available any more for this client.
Updating the arguments of `clamp_t()` and `min_t()` to `unsigned long`
fixes the issue.
Now, `avail = 65536` (before commit 10a68cdf10 `avail = 21845`), but
`num = 4` remains the same.
Fixes: c54f24e338ed (nfsd: fix performance-limiting session calculation)
Cc: stable@vger.kernel.org
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c54f24e338ed2a35218f117a4a1afb5f9e2b4e64 ]
We're unintentionally limiting the number of slots per nfsv4.1 session
to 10. Often more than 10 simultaneous RPCs are needed for the best
performance.
This calculation was meant to prevent any one client from using up more
than a third of the limit we set for total memory use across all clients
and sessions. Instead, it's limiting the client to a third of the
maximum for a single session.
Fix this.
Reported-by: Chris Tracy <ctracy@engr.scu.edu>
Cc: stable@vger.kernel.org
Fixes: de766e570413 "nfsd: give out fewer session slots as limit approaches"
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de766e570413bd0484af0b580299b495ada625c3 ]
Instead of granting client's full requests until we hit our DRC size
limit and then failing CREATE_SESSIONs (and hence mounts) completely,
start granting clients smaller slot tables as we approach the limit.
The factor chosen here is pretty much arbitrary.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44d8660d3bb0a1c8363ebcb906af2343ea8e15f6 ]
An NFSv4.1+ client negotiates the size of its duplicate reply cache size
in the initial CREATE_SESSION request. The server preallocates the
memory for the duplicate reply cache to ensure that we'll never fail to
record the response to a nonidempotent operation.
To prevent a few CREATE_SESSIONs from consuming all of memory we set an
upper limit based on nr_free_buffer_pages(). 1/2^10 has been too
limiting in practice; 1/2^7 is still less than one percent.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fd1ab747d2b1ec7ec663ad0b41a32eaa35117a8 ]
If the server that does not implement NFSv4.1 persistent session
semantics reboots while we are performing an exclusive create,
then the return value of NFS4ERR_DELAY when we replay the open
during the grace period causes us to lose the verifier.
When the grace period expires, and we present a new verifier,
the server will then correctly reply NFS4ERR_EXIST.
This commit ensures that we always present the same verifier when
replaying the OPEN.
Reported-by: Tigran Mkrtchyan <tigran.mkrtchyan@desy.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9bd2bbc01d17ddd567cc0f81f77fe1163e497462 upstream.
gcc 7.1 reports the following warning:
block/elevator.c: In function ‘elv_register’:
block/elevator.c:898:5: warning: ‘snprintf’ output may be truncated before the last format character [-Wformat-truncation=]
"%s_io_cq", e->elevator_name);
^~~~~~~~~~
block/elevator.c:897:3: note: ‘snprintf’ output between 7 and 22 bytes into a destination of size 21
snprintf(e->icq_cache_name, sizeof(e->icq_cache_name),
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s_io_cq", e->elevator_name);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The bug is that the name of the icq_cache is 6 characters longer than
the elevator name, but only ELV_NAME_MAX + 5 characters were reserved
for it --- so in the case of a maximum-length elevator name, the 'q'
character in "_io_cq" would be truncated by snprintf(). Fix it by
reserving ELV_NAME_MAX + 6 characters instead.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2446a68ae6a8cee6d480e2f5b52f5007c7c41312 ]
Don't cache eth dest pointer before calling pskb_may_pull.
Fixes: cf0f02d04a83 ("[BRIDGE]: use llc for receiving STP packets")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3b26a5d03d35d8f732d75951218983c0f7f68dff ]
We get a pointer to the ipv6 hdr in br_ip6_multicast_query but we may
call pskb_may_pull afterwards and end up using a stale pointer.
So use the header directly, it's just 1 place where it's needed.
Fixes: 08b202b67264 ("bridge br_multicast: IPv6 MLD support.")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Tested-by: Martin Weinelt <martin@linuxlounge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9d1bc24b52fb8c5d859f9a47084bf1179470e04c ]
bond_xmit_roundrobin() checks for IGMP packets but it parses
the IP header even before checking skb->protocol.
We should validate the IP header with pskb_may_pull() before
using iph->protocol.
Reported-and-tested-by: syzbot+e5be16aa39ad6e755391@syzkaller.appspotmail.com
Fixes: a2fd940f4cff ("bonding: fix broken multicast with round-robin mode")
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e858faf556d4e14c750ba1e8852783c6f9520a0e ]
If an app is playing tricks to reuse a socket via tcp_disconnect(),
bytes_acked/received needs to be reset to 0. Otherwise tcp_info will
report the sum of the current and the old connection..
Cc: Eric Dumazet <edumazet@google.com>
Fixes: 0df48c26d841 ("tcp: add tcpi_bytes_acked to tcp_info")
Fixes: bdd1f9edacb5 ("tcp: add tcpi_bytes_received to tcp_info")
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4638faac032756f7eab5524be7be56bee77e426b ]
sock_efree() releases the sock refcnt, if we don't hold this refcnt
when setting skb->destructor to it, the refcnt would not be balanced.
This leads to several bug reports from syzbot.
I have checked other users of sock_efree(), all of them hold the
sock refcnt.
Fixes: c8c8218ec5af ("netrom: fix a memory leak in nr_rx_frame()")
Reported-and-tested-by: <syzbot+622bdabb128acc33427d@syzkaller.appspotmail.com>
Reported-and-tested-by: <syzbot+6eaef7158b19e3fec3a0@syzkaller.appspotmail.com>
Reported-and-tested-by: <syzbot+9399c158fcc09b21d0d2@syzkaller.appspotmail.com>
Reported-and-tested-by: <syzbot+a34e5f3d0300163f0c87@syzkaller.appspotmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c8c8218ec5af5d2598381883acbefbf604e56b5e ]
When the skb is associated with a new sock, just assigning
it to skb->sk is not sufficient, we have to set its destructor
to free the sock properly too.
Reported-by: syzbot+d6636a36d3c34bd88938@syzkaller.appspotmail.com
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a261e3797506bd561700be643fe1a85bf81e9661 ]
The onboard sky2 NIC on ASUS P6T WS PRO doesn't work after PM resume
due to the infamous IRQ problem. Disabling MSI works around it, so
let's add it to the blacklist.
Unfortunately the BIOS on the machine doesn't fill the standard
DMI_SYS_* entry, so we pick up DMI_BOARD_* entries instead.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1142496
Reported-and-tested-by: Marcus Seyfarth <m.seyfarth@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dd006fc434e107ef90f7de0db9907cbc1c521645 ]
The frags_q is not properly initialized, it may result in illegal memory
access when conn_info is NULL.
The "goto free_exit" should be replaced by "goto exit".
Signed-off-by: Yang Wei <albin_yang@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 35cbef9863640f06107144687bd13151bc2e8ce3 ]
Currently we silently ignore filters if we cannot meet the filter
requirements. This will lead to the MAC dropping packets that are
expected to pass. A better solution would be to set the NIC to promisc
mode when the required filters cannot be met.
Also correct the number of MDF filters supported. It should be 17,
not 16.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2e60546368165c2449564d71f6005dda9205b5fb ]
Avoid the situation where an IPV6 only flag is applied to an IPv4 address:
# ip addr add 192.0.2.1/24 dev dummy0 nodad home mngtmpaddr noprefixroute
# ip -4 addr show dev dummy0
2: dummy0: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
inet 192.0.2.1/24 scope global noprefixroute dummy0
valid_lft forever preferred_lft forever
Or worse, by sending a malicious netlink command:
# ip -4 addr show dev dummy0
2: dummy0: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
inet 192.0.2.1/24 scope global nodad optimistic dadfailed home tentative mngtmpaddr noprefixroute stable-privacy dummy0
valid_lft forever preferred_lft forever
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ea811b795df24644a8eb760b493c43fba4450677 ]
This patch fixes an issue seen on Power systems with bnx2x which results
in the skb is NULL WARN_ON in bnx2x_free_tx_pkt firing due to the skb
pointer getting loaded in bnx2x_free_tx_pkt prior to the hw_cons
load in bnx2x_tx_int. Adding a read memory barrier resolves the issue.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd293d071ffe65e645b4d8104f9d8fe15ea13862 upstream.
When thin-volume is built on loop device, if available memory is low,
the following deadlock can be triggered:
One process P1 allocates memory with GFP_FS flag, direct alloc fails,
memory reclaim invokes memory shrinker in dm_bufio, dm_bufio_shrink_scan()
runs, mutex dm_bufio_client->lock is acquired, then P1 waits for dm_buffer
IO to complete in __try_evict_buffer().
But this IO may never complete if issued to an underlying loop device
that forwards it using direct-IO, which allocates memory using
GFP_KERNEL (see: do_blockdev_direct_IO()). If allocation fails, memory
reclaim will invoke memory shrinker in dm_bufio, dm_bufio_shrink_scan()
will be invoked, and since the mutex is already held by P1 the loop
thread will hang, and IO will never complete. Resulting in ABBA
deadlock.
Cc: stable@vger.kernel.org
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e244c4699f859cf7149b0781b1894c7996a8a1df upstream.
With Link Power Management (LPM) enabled USB3 links transition to low
power U1/U2 link states from U0 state automatically.
Current hub code detects USB3 remote wakeups by checking if the software
state still shows suspended, but the link has transitioned from suspended
U3 to enabled U0 state.
As it takes some time before the hub thread reads the port link state
after a USB3 wake notification, the link may have transitioned from U0
to U1/U2, and wake is not detected by hub code.
Fix this by handling U1/U2 states in the same way as U0 in USB3 wakeup
handling
This patch should be added to stable kernels since 4.13 where LPM was
kept enabled during suspend/resume
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Lee, Chiasheng <chiasheng.lee@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d87b88ba26eabd4745e158ecfd87c93a9b51dc2 upstream.
Microsoft Surface Precision Mouse provides bogus identity address when
pairing. It connects with Static Random address but provides Public
Address in SMP Identity Address Information PDU. Address has same
value but type is different. Workaround this by dropping IRK if ID
address discrepancy is detected.
> HCI Event: LE Meta Event (0x3e) plen 19
LE Connection Complete (0x01)
Status: Success (0x00)
Handle: 75
Role: Master (0x00)
Peer address type: Random (0x01)
Peer address: E0:52:33:93:3B:21 (Static)
Connection interval: 50.00 msec (0x0028)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Master clock accuracy: 0x00
....
> ACL Data RX: Handle 75 flags 0x02 dlen 12
SMP: Identity Address Information (0x09) len 7
Address type: Public (0x00)
Address: E0:52:33:93:3B:21
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Tested-by: Maarten Fonville <maarten.fonville@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199461
Cc: stable@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 918b8646497b5dba6ae82d4a7325f01b258972b9 upstream.
Commit 4e0eaf239fb3 ("intel_th: msu: Fix single mode with IOMMU") switched
the single mode code to use dma mapping pages obtained from the page
allocator, but with IOMMU disabled, that may lead to using SWIOTLB bounce
buffers and without additional sync'ing, produces empty trace buffers.
Fix this by using a DMA32 GFP flag to the page allocation in single mode,
as the device supports full 32-bit DMA addressing.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Fixes: 4e0eaf239fb3 ("intel_th: msu: Fix single mode with IOMMU")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reported-by: Ammy Yi <ammy.yi@intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190621161930.60785-4-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bdf8a8245fdea6f075a5fede833a5fcf1b3466c upstream.
ECRYPTFS_SIZE_AND_MARKER_BYTES is type size_t, so if "rc" is negative
that gets type promoted to a high positive value and treated as success.
Fixes: 778aeb42a708 ("eCryptfs: Cleanup and optimize ecryptfs_lookup_interpose()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[tyhicks: Use "if/else if" rather than "if/if"]
Cc: stable@vger.kernel.org
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f474c28fbcbe42faca4eb415172c07d76adcb819 upstream.
powerpc hardware triggers watchpoint before executing the instruction.
To make trigger-after-execute behavior, kernel emulates the
instruction. If the instruction is 'load something into non-volatile
register', exception handler should restore emulated register state
while returning back, otherwise there will be register state
corruption. eg, adding a watchpoint on a list can corrput the list:
# cat /proc/kallsyms | grep kthread_create_list
c00000000121c8b8 d kthread_create_list
Add watchpoint on kthread_create_list->prev:
# perf record -e mem:0xc00000000121c8c0
Run some workload such that new kthread gets invoked. eg, I just
logged out from console:
list_add corruption. next->prev should be prev (c000000001214e00), \
but was c00000000121c8b8. (next=c00000000121c8b8).
WARNING: CPU: 59 PID: 309 at lib/list_debug.c:25 __list_add_valid+0xb4/0xc0
CPU: 59 PID: 309 Comm: kworker/59:0 Kdump: loaded Not tainted 5.1.0-rc7+ #69
...
NIP __list_add_valid+0xb4/0xc0
LR __list_add_valid+0xb0/0xc0
Call Trace:
__list_add_valid+0xb0/0xc0 (unreliable)
__kthread_create_on_node+0xe0/0x260
kthread_create_on_node+0x34/0x50
create_worker+0xe8/0x260
worker_thread+0x444/0x560
kthread+0x160/0x1a0
ret_from_kernel_thread+0x5c/0x70
List corruption happened because it uses 'load into non-volatile
register' instruction:
Snippet from __kthread_create_on_node:
c000000000136be8: addis r29,r2,-19
c000000000136bec: ld r29,31424(r29)
if (!__list_add_valid(new, prev, next))
c000000000136bf0: mr r3,r30
c000000000136bf4: mr r5,r28
c000000000136bf8: mr r4,r29
c000000000136bfc: bl c00000000059a2f8 <__list_add_valid+0x8>
Register state from WARN_ON():
GPR00: c00000000059a3a0 c000007ff23afb50 c000000001344e00 0000000000000075
GPR04: 0000000000000000 0000000000000000 0000001852af8bc1 0000000000000000
GPR08: 0000000000000001 0000000000000007 0000000000000006 00000000000004aa
GPR12: 0000000000000000 c000007ffffeb080 c000000000137038 c000005ff62aaa00
GPR16: 0000000000000000 0000000000000000 c000007fffbe7600 c000007fffbe7370
GPR20: c000007fffbe7320 c000007fffbe7300 c000000001373a00 0000000000000000
GPR24: fffffffffffffef7 c00000000012e320 c000007ff23afcb0 c000000000cb8628
GPR28: c00000000121c8b8 c000000001214e00 c000007fef5b17e8 c000007fef5b17c0
Watchpoint hit at 0xc000000000136bec.
addis r29,r2,-19
=> r29 = 0xc000000001344e00 + (-19 << 16)
=> r29 = 0xc000000001214e00
ld r29,31424(r29)
=> r29 = *(0xc000000001214e00 + 31424)
=> r29 = *(0xc00000000121c8c0)
0xc00000000121c8c0 is where we placed a watchpoint and thus this
instruction was emulated by emulate_step. But because handle_dabr_fault
did not restore emulated register state, r29 still contains stale
value in above register state.
Fixes: 5aae8a5370802 ("powerpc, hw_breakpoints: Implement hw_breakpoints for 64-bit server processors")
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: stable@vger.kernel.org # 2.6.36+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ecb78ef56e08d2119d337ae23cb951a640dc52d upstream.
Previously, only IBAT1 and IBAT2 were used to map kernel linear mem.
Since commit 63b2bc619565 ("powerpc/mm/32s: Use BATs for
STRICT_KERNEL_RWX"), we may have all 8 BATs used for mapping
kernel text. But the suspend/restore functions only save/restore
BATs 0 to 3, and clears BATs 4 to 7.
Make suspend and restore functions respectively save and reload
the 8 BATs on CPUs having MMU_FTR_USE_HIGH_BATS feature.
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10835c854685393a921b68f529bf740fa7c9984d upstream.
On parisc the privilege level of a process is stored in the lowest two bits of
the instruction pointers (IAOQ0 and IAOQ1). On Linux we use privilege level 0
for the kernel and privilege level 3 for user-space. So userspace should not be
allowed to modify IAOQ0 or IAOQ1 of a ptraced process to change it's privilege
level to e.g. 0 to try to gain kernel privileges.
This patch prevents such modifications by always setting the two lowest bits to
one (which relates to privilege level 3 for user-space) if IAOQ0 or IAOQ1 are
modified via ptrace calls in the native and compat ptrace paths.
Link: https://bugs.gentoo.org/481768
Reported-by: Jeroen Roovers <jer@gentoo.org>
Cc: <stable@vger.kernel.org>
Tested-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d1f62c686acdedf5ed9642b763f3808d6a47d1e upstream.
The saturation bit was being set at bit 9 in the second 32-bit word
of the TPMEM CSC. This isn't correct, the saturation bit is bit 42,
which is bit 10 of the second word.
Fixes: 1aa8ea0d2bd5d ("gpu: ipu-v3: Add Image Converter unit")
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fa0a1da3dadfd9216df7745a1331fdaa0940d1c upstream.
Patch series "Coda updates".
The following patch series is a collection of various fixes for Coda,
most of which were collected from linux-fsdevel or linux-kernel but
which have as yet not found their way upstream.
This patch (of 22):
Various file systems expect that vma->vm_file points at their own file
handle, several use file_inode(vma->vm_file) to get at their inode or
use vma->vm_file->private_data. However the way Coda wrapped mmap on a
host file broke this assumption, vm_file was still pointing at the Coda
file and the host file systems would scribble over Coda's inode and
private file data.
This patch fixes the incorrect expectation and wraps vm_ops->open and
vm_ops->close to allow Coda to track when the vm_area_struct is
destroyed so we still release the reference on the Coda file handle at
the right time.
[This patch differs from the original upstream patch because older stable
kernels do not have the call_mmap vfs helper so we call f_ops->mmap
directly.]
Link: http://lkml.kernel.org/r/0e850c6e59c0b147dc2dcd51a3af004c948c3697.1558117389.git.jaharkes@cs.cmu.edu
Signed-off-by: Jan Harkes <jaharkes@cs.cmu.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Fabian Frederick <fabf@skynet.be>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Yann Droneaud <ydroneaud@opteya.com>
Cc: Zhouyang Jia <jiazhouyang09@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jan Harkes <jaharkes@cs.cmu.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit da99466ac243f15fbba65bd261bfc75ffa1532b6 ]
This fixes a global out-of-bounds read access in the copy_buffer
function of the floppy driver.
The FDDEFPRM ioctl allows one to set the geometry of a disk. The sect
and head fields (unsigned int) of the floppy_drive structure are used to
compute the max_sector (int) in the make_raw_rw_request function. It is
possible to overflow the max_sector. Next, max_sector is passed to the
copy_buffer function and used in one of the memcpy calls.
An unprivileged user could trigger the bug if the device is accessible,
but requires a floppy disk to be inserted.
The patch adds the check for the .sect * .head multiplication for not
overflowing in the set_geometry function.
The bug was found by syzkaller.
Signed-off-by: Denis Efremov <efremov@ispras.ru>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9b04609b784027968348796a18f601aed9db3789 ]
This fixes the invalid pointer dereference in the drive_name function of
the floppy driver.
The native_format field of the struct floppy_drive_params is used as
floppy_type array index in the drive_name function. Thus, the field
should be checked the same way as the autodetect field.
To trigger the bug, one could use a value out of range and set the drive
parameters with the FDSETDRVPRM ioctl. Next, FDGETDRVTYP ioctl should
be used to call the drive_name. A floppy disk is not required to be
inserted.
CAP_SYS_ADMIN is required to call FDSETDRVPRM.
The patch adds the check for a value of the native_format field to be in
the '0 <= x < ARRAY_SIZE(floppy_type)' range of the floppy_type array
indices.
The bug was found by syzkaller.
Signed-off-by: Denis Efremov <efremov@ispras.ru>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5635f897ed83fd539df78e98ba69ee91592f9bb8 ]
This fixes a global out-of-bounds read access in the next_valid_format
function of the floppy driver.
The values from autodetect field of the struct floppy_drive_params are
used as indices for the floppy_type array in the next_valid_format
function 'floppy_type[DP->autodetect[probed_format]].sect'.
To trigger the bug, one could use a value out of range and set the drive
parameters with the FDSETDRVPRM ioctl. A floppy disk is not required to
be inserted.
CAP_SYS_ADMIN is required to call FDSETDRVPRM.
The patch adds the check for values of the autodetect field to be in the
'0 <= x < ARRAY_SIZE(floppy_type)' range of the floppy_type array indices.
The bug was found by syzkaller.
Signed-off-by: Denis Efremov <efremov@ispras.ru>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f3554aeb991214cbfafd17d55e2bfddb50282e32 ]
This fixes a divide by zero error in the setup_format_params function of
the floppy driver.
Two consecutive ioctls can trigger the bug: The first one should set the
drive geometry with such .sect and .rate values for the F_SECT_PER_TRACK
to become zero. Next, the floppy format operation should be called.
A floppy disk is not required to be inserted. An unprivileged user
could trigger the bug if the device is accessible.
The patch checks F_SECT_PER_TRACK for a non-zero value in the
set_geometry function. The proper check should involve a reasonable
upper limit for the .sect and .rate fields, but it could change the
UAPI.
The patch also checks F_SECT_PER_TRACK in the setup_format_params, and
cancels the formatting operation in case of zero.
The bug was found by syzkaller.
Signed-off-by: Denis Efremov <efremov@ispras.ru>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 229b53c9bf4e1132a4aa6feb9632a7a1f1d08c5c ]
all other drivers recognizing those ioctls are very much *not*
biarch.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 000dd5316e1c756a1c028f22e01d06a38249dd4d upstream.
PME polling does not take into account that a device that is directly
connected to the host bridge may go into D3cold as well. This leads to a
situation where the PME poll thread reads from a config space of a
device that is in D3cold and gets incorrect information because the
config space is not accessible.
Here is an example from Intel Ice Lake system where two PCIe root ports
are in D3cold (I've instrumented the kernel to log the PMCSR register
contents):
[ 62.971442] pcieport 0000:00:07.1: Check PME status, PMCSR=0xffff
[ 62.971504] pcieport 0000:00:07.0: Check PME status, PMCSR=0xffff
Since 0xffff is interpreted so that PME is pending, the root ports will
be runtime resumed. This repeats over and over again essentially
blocking all runtime power management.
Prevent this from happening by checking whether the device is in D3cold
before its PME status is read.
Fixes: 71a83bd727cc ("PCI/PM: add runtime PM support to PCIe port")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: 3.6+ <stable@vger.kernel.org> # v3.6+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf144f81a99d1a3928f90b0936accfd3f45c9a0a upstream.
Testing padata with the tcrypt module on a 5.2 kernel...
# modprobe tcrypt alg="pcrypt(rfc4106(gcm(aes)))" type=3
# modprobe tcrypt mode=211 sec=1
...produces this splat:
INFO: task modprobe:10075 blocked for more than 120 seconds.
Not tainted 5.2.0-base+ #16
modprobe D 0 10075 10064 0x80004080
Call Trace:
? __schedule+0x4dd/0x610
? ring_buffer_unlock_commit+0x23/0x100
schedule+0x6c/0x90
schedule_timeout+0x3b/0x320
? trace_buffer_unlock_commit_regs+0x4f/0x1f0
wait_for_common+0x160/0x1a0
? wake_up_q+0x80/0x80
{ crypto_wait_req } # entries in braces added by hand
{ do_one_aead_op }
{ test_aead_jiffies }
test_aead_speed.constprop.17+0x681/0xf30 [tcrypt]
do_test+0x4053/0x6a2b [tcrypt]
? 0xffffffffa00f4000
tcrypt_mod_init+0x50/0x1000 [tcrypt]
...
The second modprobe command never finishes because in padata_reorder,
CPU0's load of reorder_objects is executed before the unlocking store in
spin_unlock_bh(pd->lock), causing CPU0 to miss CPU1's increment:
CPU0 CPU1
padata_reorder padata_do_serial
LOAD reorder_objects // 0
INC reorder_objects // 1
padata_reorder
TRYLOCK pd->lock // failed
UNLOCK pd->lock
CPU0 deletes the timer before returning from padata_reorder and since no
other job is submitted to padata, modprobe waits indefinitely.
Add a pair of full barriers to guarantee proper ordering:
CPU0 CPU1
padata_reorder padata_do_serial
UNLOCK pd->lock
smp_mb()
LOAD reorder_objects
INC reorder_objects
smp_mb__after_atomic()
padata_reorder
TRYLOCK pd->lock
smp_mb__after_atomic is needed so the read part of the trylock operation
comes after the INC, as Andrea points out. Thanks also to Andrea for
help with writing a litmus test.
Fixes: 16295bec6398 ("padata: Generic parallelization/serialization interface")
Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: <stable@vger.kernel.org>
Cc: Andrea Parri <andrea.parri@amarulasolutions.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Paul E. McKenney <paulmck@linux.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7cb95eeea6706c790571042a06782e378b2561ea upstream.
It turns out that while disabling i2c bus access from software when the
GPU is suspended was a step in the right direction with:
commit 342406e4fbba ("drm/nouveau/i2c: Disable i2c bus access after
->fini()")
We also ended up accidentally breaking the vbios init scripts on some
older Tesla GPUs, as apparently said scripts can actually use the i2c
bus. Since these scripts are executed before initializing any
subdevices, we end up failing to acquire access to the i2c bus which has
left a number of cards with their fan controllers uninitialized. Luckily
this doesn't break hardware - it just means the fan gets stuck at 100%.
This also means that we've always been using our i2c busses before
initializing them during the init scripts for older GPUs, we just didn't
notice it until we started preventing them from being used until init.
It's pretty impressive this never caused us any issues before!
So, fix this by initializing our i2c pad and busses during subdev
pre-init. We skip initializing aux busses during pre-init, as those are
guaranteed to only ever be used by nouveau for DP aux transactions.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Tested-by: Marc Meledandri <m.meledandri@gmail.com>
Fixes: 342406e4fbba ("drm/nouveau/i2c: Disable i2c bus access after ->fini()")
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fc3977ccc5d3c22e851f2dce2d3ce2a0a843842 upstream.
If a perf_event creation fails due to any reason of the host perf
subsystem, it has no chance to log the corresponding event for guest
which may cause abnormal sampling data in guest result. In debug mode,
this message helps to understand the state of vPMC and we may not
limit the number of occurrences but not in a spamming style.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 766b9b168f6c75c350dd87c3e0bc6a9b322f0013 upstream.
The mutex unlock in the threaded interrupt handler is not paired
with any mutex lock. Remove it.
This bug has been here for a really long time, so it applies
to any stable repo.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07d89227a983df957a6a7c56f7c040cde9ac571f upstream.
cfg->type can be overridden by v4l2_ctrl_fill() and the new value is
stored in the local type var. Fix the tests to use this local var.
Fixes: 0996517cf8ea ("V4L/DVB: v4l2: Add new control handling framework")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
[hverkuil-cisco@xs4all.nl: change to !qmenu and !qmenu_int (checkpatch)]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ede34f397ddb063b145b9e7d79c6026f819ded13 upstream.
The fix for the racy writes and ioctls to sequencer widened the
application of client->ioctl_mutex to the whole write loop. Although
it does unlock/relock for the lengthy operation like the event dup,
the loop keeps the ioctl_mutex for the whole time in other
situations. This may take quite long time if the user-space would
give a huge buffer, and this is a likely cause of some weird behavior
spotted by syzcaller fuzzer.
This patch puts a simple workaround, just adding a mutex break in the
loop when a large number of events have been processed. This
shouldn't hit any performance drop because the threshold is set high
enough for usual operations.
Fixes: 7bd800915677 ("ALSA: seq: More protection for concurrent write and ioctl races")
Reported-by: syzbot+97aae04ce27e39cbfca9@syzkaller.appspotmail.com
Reported-by: syzbot+4c595632b98bb8ffcc66@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aeb87246537a83c2aff482f3f34a2e0991e02cbc upstream.
All mapping iterator logic is based on the assumption that sg->offset
is always lower than PAGE_SIZE.
But there are situations where sg->offset is such that the SG item
is on the second page. In that case sg_copy_to_buffer() fails
properly copying the data into the buffer. One of the reason is
that the data will be outside the kmapped area used to access that
data.
This patch fixes the issue by adjusting the mapping iterator
offset and pgoffset fields such that offset is always lower than
PAGE_SIZE.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 4225fc8555a9 ("lib/scatterlist: use page iterator in the mapping iterator")
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44942b4e457beda00981f616402a1a791e8c616e upstream.
According to the open() manpage, Linux reserves the access mode 3
to mean "check for read and write permission on the file and return
a file descriptor that can't be used for reading or writing."
Currently, the NFSv4 code will ask the server to open the file,
and will use an incorrect share access mode of 0. Since it has
an incorrect share access mode, the client later forgets to send
a corresponding close, meaning it can leak stateids on the server.
Fixes: ce4ef7c0a8a05 ("NFS: Split out NFS v4 file operations")
Cc: stable@vger.kernel.org # 3.6+
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
