IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 5610bcfe8693c02e2e4c8b31427f1bdbdecc839c upstream.
A race condition may occur if the user physically removes the
USB device while calling open() for this device node.
This is a race condition between the ufx_ops_open() function and
the ufx_usb_disconnect() function, which may eventually result in UAF.
So, add a mutex to the ufx_ops_open() and ufx_usb_disconnect() functions
to avoid race contidion of krefs.
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 110a58b9f91c66f743c01a2c217243d94c899c23 upstream.
uImage boot wrapper should not use SPE instructions, like kernel itself.
Boot wrapper has already disabled Altivec and VSX instructions but not SPE.
Options -mno-spe and -mspe=no already set when compilation of kernel, but
not when compiling uImage wrapper yet. Fix it.
Cc: stable@vger.kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220827134454.17365-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e32818397426a688f598f35d3bc762eca6d7592 upstream.
When pci_assign_resource() is unable to assign resources to a BAR, it uses
pci_revert_fw_address() to fall back to a firmware assignment (if any).
Previously pci_revert_fw_address() assumed all addresses could reach the
device, but this is not true if the device is below a bridge that only
forwards addresses within its windows.
This problem was observed on a Tyan Tomcat IV S1564D system where the BIOS
did not assign valid addresses to several bridges and USB devices:
pci 0000:00:11.0: PCI-to-PCIe bridge to [bus 01-ff]
pci 0000:00:11.0: bridge window [io 0xe000-0xefff]
pci 0000:01:00.0: PCIe Upstream Port to [bus 02-ff]
pci 0000:01:00.0: bridge window [io 0x0000-0x0fff] # unreachable
pci 0000:02:02.0: PCIe Downstream Port to [bus 05-ff]
pci 0000:02:02.0: bridge window [io 0x0000-0x0fff] # unreachable
pci 0000:05:00.0: PCIe-to-PCI bridge to [bus 06-ff]
pci 0000:05:00.0: bridge window [io 0x0000-0x0fff] # unreachable
pci 0000:06:08.0: USB UHCI 1.1
pci 0000:06:08.0: BAR 4: [io 0xfce0-0xfcff] # unreachable
pci 0000:06:08.1: USB UHCI 1.1
pci 0000:06:08.1: BAR 4: [io 0xfce0-0xfcff] # unreachable
pci 0000:06:08.0: can't claim BAR 4 [io 0xfce0-0xfcff]: no compatible bridge window
pci 0000:06:08.1: can't claim BAR 4 [io 0xfce0-0xfcff]: no compatible bridge window
During the first pass of assigning unassigned resources, there was not
enough I/O space available, so we couldn't assign the 06:08.0 BAR and
reverted to the firmware assignment (still unreachable). Reverting the
06:08.1 assignment failed because it conflicted with 06:08.0:
pci 0000:00:11.0: bridge window [io 0xe000-0xefff]
pci 0000:01:00.0: no space for bridge window [io size 0x2000]
pci 0000:02:02.0: no space for bridge window [io size 0x1000]
pci 0000:05:00.0: no space for bridge window [io size 0x1000]
pci 0000:06:08.0: BAR 4: no space for [io size 0x0020]
pci 0000:06:08.0: BAR 4: trying firmware assignment [io 0xfce0-0xfcff]
pci 0000:06:08.1: BAR 4: no space for [io size 0x0020]
pci 0000:06:08.1: BAR 4: trying firmware assignment [io 0xfce0-0xfcff]
pci 0000:06:08.1: BAR 4: [io 0xfce0-0xfcff] conflicts with 0000:06:08.0 [io 0xfce0-0xfcff]
A subsequent pass assigned valid bridge windows and a valid 06:08.1 BAR,
but left the 06:08.0 BAR alone, so the UHCI device was still unusable:
pci 0000:00:11.0: bridge window [io 0xe000-0xefff] released
pci 0000:00:11.0: bridge window [io 0x1000-0x2fff] # reassigned
pci 0000:01:00.0: bridge window [io 0x1000-0x2fff] # reassigned
pci 0000:02:02.0: bridge window [io 0x2000-0x2fff] # reassigned
pci 0000:05:00.0: bridge window [io 0x2000-0x2fff] # reassigned
pci 0000:06:08.0: BAR 4: assigned [io 0xfce0-0xfcff] # left alone
pci 0000:06:08.1: BAR 4: assigned [io 0x2000-0x201f]
...
uhci_hcd 0000:06:08.0: host system error, PCI problems?
uhci_hcd 0000:06:08.0: host controller process error, something bad happened!
uhci_hcd 0000:06:08.0: host controller halted, very bad!
uhci_hcd 0000:06:08.0: HCRESET not completed yet!
uhci_hcd 0000:06:08.0: HC died; cleaning up
If the address assigned by firmware is not reachable because it's not
within upstream bridge windows, fail instead of assigning the unusable
address from firmware.
[bhelgaas: commit log, use pci_upstream_bridge()]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=16263
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2203012338460.46819@angie.orcam.me.uk
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2209211921250.29493@angie.orcam.me.uk
Fixes: 58c84eda0756 ("PCI: fall back to original BIOS BAR addresses")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.35+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3cebf80e9a0d3adcb174053be32c88a640b3344b upstream.
lld since llvm:6611d58f5bbc ("[ELF] Relax R_RISCV_ALIGN"), which will be
included in the 15.0.0 release, has implemented some RISC-V linker
relaxation. -mno-relax is no longer needed in
KBUILD_CFLAGS/KBUILD_AFLAGS to suppress R_RISCV_ALIGN which older lld
can not handle:
ld.lld: error: capability.c:(.fixup+0x0): relocation R_RISCV_ALIGN
requires unimplemented linker relaxation; recompile with -mno-relax
but the .o is already compiled with -mno-relax
Signed-off-by: Fangrui Song <maskray@google.com>
Link: https://lore.kernel.org/r/20220710071117.446112-1-maskray@google.com/
Link: https://lore.kernel.org/r/20220918092933.19943-1-palmer@rivosinc.com
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e2e6042a7ec6504fe8e366717afa2f40cf16488 upstream.
Commit 2139619bcad7 ("riscv: mmap with PROT_WRITE but no PROT_READ is
invalid") made mmap() return EINVAL if PROT_WRITE was set wihtout
PROT_READ with the justification that a write-only PTE is considered a
reserved PTE permission bit pattern in the privileged spec. This check
is unnecessary since we let VM_WRITE imply VM_READ on RISC-V, and it is
inconsistent with other architectures that don't support write-only PTEs,
creating a potential software portability issue. Just remove the check
altogether and let PROT_WRITE imply PROT_READ as is the case on other
architectures.
Note that this also allows PROT_WRITE|PROT_EXEC mappings which were
disallowed prior to the aforementioned commit; PROT_READ is implied in
such mappings as well.
Fixes: 2139619bcad7 ("riscv: mmap with PROT_WRITE but no PROT_READ is invalid")
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Andrew Bresticker <abrestic@rivosinc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220915193702.2201018-3-abrestic@rivosinc.com/
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aca7c13d3bee81a968337a5515411409ae9d095d upstream.
Independend of the current graphics resolution, adjust the reported
graphics card memory size to the next 4MB boundary.
This fixes the fbtest program which expects a naturally aligned size.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cc205e3c17d5716da7ebb7fa0c985555e95d009 upstream.
Fix port I/O string accessors such as `insb', `outsb', etc. which use
the physical PCI port I/O address rather than the corresponding memory
mapping to get at the requested location, which in turn breaks at least
accesses made by our parport driver to a PCIe parallel port such as:
PCI parallel port detected: 1415:c118, I/O at 0x1000(0x1008), IRQ 20
parport0: PC-style at 0x1000 (0x1008), irq 20, using FIFO [PCSPP,TRISTATE,COMPAT,EPP,ECP]
causing a memory access fault:
Unable to handle kernel access to user memory without uaccess routines at virtual address 0000000000001008
Oops [#1]
Modules linked in:
CPU: 1 PID: 350 Comm: cat Not tainted 6.0.0-rc2-00283-g10d4879f9ef0-dirty #23
Hardware name: SiFive HiFive Unmatched A00 (DT)
epc : parport_pc_fifo_write_block_pio+0x266/0x416
ra : parport_pc_fifo_write_block_pio+0xb4/0x416
epc : ffffffff80542c3e ra : ffffffff80542a8c sp : ffffffd88899fc60
gp : ffffffff80fa2700 tp : ffffffd882b1e900 t0 : ffffffd883d0b000
t1 : ffffffffff000002 t2 : 4646393043330a38 s0 : ffffffd88899fcf0
s1 : 0000000000001000 a0 : 0000000000000010 a1 : 0000000000000000
a2 : ffffffd883d0a010 a3 : 0000000000000023 a4 : 00000000ffff8fbb
a5 : ffffffd883d0a001 a6 : 0000000100000000 a7 : ffffffc800000000
s2 : ffffffffff000002 s3 : ffffffff80d28880 s4 : ffffffff80fa1f50
s5 : 0000000000001008 s6 : 0000000000000008 s7 : ffffffd883d0a000
s8 : 0004000000000000 s9 : ffffffff80dc1d80 s10: ffffffd8807e4000
s11: 0000000000000000 t3 : 00000000000000ff t4 : 393044410a303930
t5 : 0000000000001000 t6 : 0000000000040000
status: 0000000200000120 badaddr: 0000000000001008 cause: 000000000000000f
[<ffffffff80543212>] parport_pc_compat_write_block_pio+0xfe/0x200
[<ffffffff8053bbc0>] parport_write+0x46/0xf8
[<ffffffff8050530e>] lp_write+0x158/0x2d2
[<ffffffff80185716>] vfs_write+0x8e/0x2c2
[<ffffffff80185a74>] ksys_write+0x52/0xc2
[<ffffffff80185af2>] sys_write+0xe/0x16
[<ffffffff80003770>] ret_from_syscall+0x0/0x2
---[ end trace 0000000000000000 ]---
For simplicity address the problem by adding PCI_IOBASE to the physical
address requested in the respective wrapper macros only, observing that
the raw accessors such as `__insb', `__outsb', etc. are not supposed to
be used other than by said macros. Remove the cast to `long' that is no
longer needed on `addr' now that it is used as an offset from PCI_IOBASE
and add parentheses around `addr' needed for predictable evaluation in
macro expansion. No need to make said adjustments in separate changes
given that current code is gravely broken and does not ever work.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: fab957c11efe2 ("RISC-V: Atomic and Locking Code")
Cc: stable@vger.kernel.org # v4.15+
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2209220223080.29493@angie.orcam.me.uk
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8478ed5844588703a1a4c96a004b1525fbdbdd5e upstream.
On recent kernels, the PM8058 L16 (or any other PM8058 LDO-regulator)
does not come up if they are supplied by an SMPS-regulator. This
is not very strange since the regulators are registered in a long
array and the L-regulators are registered before the S-regulators,
and if an L-regulator defers, it will never get around to registering
the S-regulator that it needs.
See arch/arm/boot/dts/qcom-apq8060-dragonboard.dts:
pm8058-regulators {
(...)
vdd_l13_l16-supply = <&pm8058_s4>;
(...)
Ooops.
Fix this by moving the PM8058 S-regulators first in the array.
Do the same for the PM8901 S-regulators (though this is currently
not causing any problems with out device trees) so that the pattern
of registration order is the same on all PMnnnn chips.
Fixes: 087a1b5cdd55 ("regulator: qcom: Rework to single platform device")
Cc: stable@vger.kernel.org
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@somainline.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220909112529.239143-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea8ef003aa53ad23e7705c5cab1c4e664faa6c79 upstream.
Slimbus streams are first prepared and then enabled, so the cleanup path
should reverse it. The unprepare sets stream->num_ports to 0 and frees
the stream->ports. Calling disable after unprepare was not really
effective (channels was not deactivated) and could lead to further
issues due to making transfers on unprepared stream.
Fixes: 20aedafdf492 ("ASoC: wcd9335: add support to wcd9335 codec")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220921145354.1683791-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be6e2b5734a425941fcdcdbd2a9337be498ce2cf upstream.
This fixes broken atomic checks which cause a race between the
release-timer and processing of hid input.
I noticed that contacts were sometimes sticking, even with the "sticky
fingers" quirk enabled. This fixes that problem.
Cc: stable@vger.kernel.org
Fixes: 9609827458c3 ("HID: multitouch: optimize the sticky fingers timer")
Signed-off-by: Andri Yngvason <andri@yngvason.is>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20220907150159.2285460-1-andri@yngvason.is
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44637ca41d551d409a481117b07fa209b330fca9 upstream.
During lock arg validation, first check for -EBUSY cases, then for
-EINVAL cases. The -EINVAL checks look at lkb state variables
which are not stable when an lkb is busy and would cause an
-EBUSY result, e.g. lkb->lkb_grmode.
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eef6ec9bf390e836a6c4029f3620fe49528aa1fe upstream.
This patch fixes a race by using ls_cb_mutex around the bit
operations and conditional code blocks for LSFL_CB_DELAY.
The function dlm_callback_stop() expects to stop all callbacks and
flush all currently queued onces. The set_bit() is not enough because
there can still be queue_work() after the workqueue was flushed.
To avoid queue_work() after set_bit(), surround both by ls_cb_mutex.
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e141772e6465f937458b35ddcfd0a981b6f5280 upstream.
The Spreadtrum controller supports 100KHz minimal clock rate, which means
that the current value 400KHz is wrong.
Unfortunately this has also lead to fail to initialize some cards, which
are allowed to require 100KHz to work. So, let's fix the problem by
changing the minimal supported clock rate to 100KHz.
Signed-off-by: Wenchao Chen <wenchao.chen@unisoc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: fb8bd90f83c4 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221011104935.10980-1-wenchao.chen666@gmail.com
[Ulf: Clarified to commit-message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0be1a655fe68c8e6dcadbcbddb69cf2fb29881f5 upstream.
can_restart() expects CMD_START_CHIP to set the error state to
ERROR_ACTIVE as it calls netif_carrier_on() immediately afterwards.
Otherwise the user may immediately trigger restart again and hit a
BUG_ON() in can_restart().
Fix kvaser_usb_leaf set_mode(CMD_START_CHIP) to set the expected state.
Cc: stable@vger.kernel.org
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010150829.199676-5-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 455561fb618fde40558776b5b8435f9420f335db upstream.
The TX queue seems to be implicitly flushed by the hardware during
bus-off or bus-off recovery, but the driver does not reset the TX
bookkeeping.
Despite not resetting TX bookkeeping the driver still re-enables TX
queue unconditionally, leading to "cannot find free context" /
NETDEV_TX_BUSY errors if the TX queue was full at bus-off time.
Fix that by resetting TX bookkeeping on CAN restart.
Tested with 0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778.
Cc: stable@vger.kernel.org
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010150829.199676-4-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1499ecaea9d2ba68d5e18d80573b4561a8dc4ee7 upstream.
For command events read from the device,
kvaser_usb_leaf_read_bulk_callback() verifies that cmd->len does not
exceed the size of the received data, but the actual kvaser_cmd handlers
will happily read any kvaser_cmd fields without checking for cmd->len.
This can cause an overread if the last cmd in the buffer is shorter than
expected for the command type (with cmd->len showing the actual short
size).
Maximum overread seems to be 22 bytes (CMD_LEAF_LOG_MESSAGE), some of
which are delivered to userspace as-is.
Fix that by verifying the length of command before handling it.
This issue can only occur after RX URBs have been set up, i.e. the
interface has been opened at least once.
Cc: stable@vger.kernel.org
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010150829.199676-2-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd7f30e174d09a02ca2afa5ef093fb0f0352e0d8 upstream.
flush_comp is initialized when CMD_FLUSH_QUEUE is sent to the device and
completed when the device sends CMD_FLUSH_QUEUE_RESP.
This causes completion of uninitialized completion if the device sends
CMD_FLUSH_QUEUE_RESP before CMD_FLUSH_QUEUE is ever sent (e.g. as a
response to a flush by a previously bound driver, or a misbehaving
device).
Fix that by initializing flush_comp in kvaser_usb_init_one() like the
other completions.
This issue is only triggerable after RX URBs have been set up, i.e. the
interface has been opened at least once.
Cc: stable@vger.kernel.org
Fixes: aec5fb2268b7 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010150829.199676-3-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37d49519b41405b08748392c6a7f193d9f77ecd2 upstream.
The Lenovo OneLink+ Dock contains two VL812 USB3.0 controllers:
17ef:1018 upstream
17ef:1019 downstream
These hubs suffer from two separate problems:
1) After the host system was suspended and woken up, the hubs appear to
be in a random state. Some downstream ports (both internal to the
built-in audio and network controllers, and external to USB sockets)
may no longer be functional. The exact list of disabled ports (if
any) changes from wakeup to wakeup. Ports remain in that state until
the dock is power-cycled, or until the laptop is rebooted.
Wakeup sources connected to the hubs (keyboard, WoL on the integrated
gigabit controller) will wake the system up from suspend, but they
may no longer work after wakeup (and in that case will no longer work
as wakeup source in a subsequent suspend-wakeup cycle).
This issue appears in the logs with messages such as:
usb 1-6.1-port4: cannot disable (err = -71)
usb 1-6-port2: cannot disable (err = -71)
usb 1-6.1: clear tt 1 (80c0) error -71
usb 1-6-port4: cannot disable (err = -71)
usb 1-6.4: PM: dpm_run_callback(): usb_dev_resume+0x0/0x10 [usbcore] returns -71
usb 1-6.4: PM: failed to resume async: error -71
usb 1-7: reset full-speed USB device number 5 using xhci_hcd
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: Cannot enable. Maybe the USB cable is bad?
usb 1-6.1-port1: cannot disable (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: Cannot enable. Maybe the USB cable is bad?
usb 1-6.1-port1: cannot disable (err = -71)
2) Some USB devices cannot be enumerated properly. So far I have only
seen the issue with USB 3.0 devices. The same devices work without
problem directly connected to the host system, to other systems or to
other hubs (even when those hubs are connected to the OneLink+ dock).
One very reliable reproducer is this USB 3.0 HDD enclosure:
152d:9561 JMicron Technology Corp. / JMicron USA Technology Corp. Mobius
I have seen it happen sporadically with other USB 3.0 enclosures,
with controllers from different manufacturers, all self-powered.
Typical messages in the logs:
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
usb 2-1.4: device not accepting address 6, error -62
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
usb 2-1.4: device not accepting address 7, error -62
usb 2-1-port4: attempt power cycle
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
usb 2-1.4: device not accepting address 8, error -62
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
usb 2-1.4: device not accepting address 9, error -62
usb 2-1-port4: unable to enumerate USB device
Through trial and error, I found that the USB_QUIRK_RESET_RESUME solved
the second issue. Further testing then uncovered the first issue. Test
results are summarized in this table:
=======================================================================================
Settings USB2 hotplug USB3 hotplug State after waking up
---------------------------------------------------------------------------------------
power/control=auto works fails broken
usbcore.autosuspend=-1 works works broken
OR power/control=on
power/control=auto works (1) works (1) works
and USB_QUIRK_RESET_RESUME
power/control=on works works works
and USB_QUIRK_RESET_RESUME
HUB_QUIRK_DISABLE_AUTOSUSPEND works works works
and USB_QUIRK_RESET_RESUME
=======================================================================================
In those results, the power/control settings are applied to both hubs,
both on the USB2 and USB3 side, before each test.
From those results, USB_QUIRK_RESET_RESUME is required to reset the hubs
properly after a suspend-wakeup cycle, and the hubs must not autosuspend
to work around the USB3 issue.
A secondary effect of USB_QUIRK_RESET_RESUME is to prevent the hubs'
upstream links from suspending (the downstream ports can still suspend).
This secondary effect is used in results (1). It is enough to solve the
USB3 problem.
Setting USB_QUIRK_RESET_RESUME on those hubs is the smallest patch that
solves both issues.
Prior to creating this patch, I have used the USB_QUIRK_RESET_RESUME via
the kernel command line for over a year without noticing any side
effect.
Thanks to Oliver Neukum @Suse for explanations of the operations of
USB_QUIRK_RESET_RESUME, and requesting more testing.
Signed-off-by: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220927073407.5672-1-jflf_kernel@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b4ab4abcea4c0c10b25187bf2569e5a07e9a20c upstream.
The DPS310 chip has been observed to get "stuck" such that pressure
and temperature measurements are never indicated as "ready" in the
MEAS_CFG register. The only solution is to reset the device and try
again. In order to avoid continual failures, use a boolean flag to
only try the reset after timeout once if errors persist.
Fixes: ba6ec48e76bc ("iio: Add driver for Infineon DPS310")
Cc: <stable@vger.kernel.org>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220915195719.136812-3-eajames@linux.ibm.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2329717bdd3fa62f8a2f3d8d85ad0bee4556bd7 upstream.
Move the startup procedure into a function, and correct a missing
check on the return code for writing the PRS_CFG register.
Cc: <stable@vger.kernel.org>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220915195719.136812-2-eajames@linux.ibm.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 558a25f903b4af6361b7fbeea08a6446a0745653 upstream.
For reliable operation across the full range of supported
interface rates, the AD5593R needs a STOP condition between
address write, and data read (like show in the datasheet Figure 40)
so in turn i2c_smbus_read_word_swapped cannot be used.
While at it, a simple helper was added to make the code simpler.
Fixes: 56ca9db862bf ("iio: dac: Add support for the AD5592R/AD5593R ADCs/DACs")
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220913073413.140475-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e98ecc6e94f4e6d21c06660b0f336df02836694f upstream.
Commit d5c7076b772a ("smb3: add smb3.1.1 to default dialect list")
extend the dialects from 3 to 4, but forget to decrease the extended
length when specific the dialect, then the message length is larger
than expected.
This maybe leak some info through network because not initialize the
message body.
After apply this patch, the VALIDATE_NEGOTIATE_INFO message length is
reduced from 28 bytes to 26 bytes.
Fixes: d5c7076b772a ("smb3: add smb3.1.1 to default dialect list")
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Cc: <stable@vger.kernel.org>
Acked-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Tom Talpey <tom@talpey.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb44c31cdcac107344dd2fcc3bd0504a53575c51 upstream.
This is the opposite case of kernel bugzilla 216301.
If we mmap a file using cache=none and then proceed to update the mmapped
area these updates are not reflected in a later pread() of that part of the
file.
To fix this we must first destage any dirty pages in the range before
we allow the pread() to proceed.
Cc: stable@vger.kernel.org
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Enzo Matsumiya <ematsumiya@suse.de>
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1161703c9bd664da5e3b2eb1a3bb40c210e026ea upstream.
Every dma_map_single() call should have its dma_unmap_single() counterpart,
because the DMA address space is a shared resource and one could render the
machine unusable by consuming all DMA addresses.
Link: https://lore.kernel.org/lkml/13c6c9a2-6db5-c3bf-349b-4c127ad3496a@axentia.se/
Cc: stable@vger.kernel.org
Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Alexander Dahl <ada@thorsis.com>
Reported-by: Peter Rosin <peda@axentia.se>
Tested-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220728074014.145406-1-tudor.ambarus@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ea8e1297801f7b0220ebf6ae61a5b74ca83981e upstream.
The ASUS ROG X16 (GV601R) series laptop has the same node-to-DAC pairs
as early models and the G14, this includes bass speakers which are by
default mapped incorrectly to the 0x06 node.
Add a quirk to use the same DAC pairs as the G14.
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20221010070347.36883-1-luke@ljones.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66ba7c88507344dee68ad1acbdb630473ab36114 upstream.
The initial fix for ASUS G533Z was based on faulty information. This
fixes the pincfg to values that have been verified with no existing
module options or other hacks enabled.
Enables headphone jack, and 5.1 surround.
[ corrected the indent level by tiwai ]
Fixes: bc2c23549ccd ("ALSA: hda/realtek: Add pincfg for ASUS G533Z HP jack")
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20221010065702.35190-1-luke@ljones.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 417b9c51f59734d852e47252476fadc293ad994a upstream.
After some feedback from users with Dell Precision 5530 machines, this
patch reverts the previous change to add ALC289_FIXUP_DUAL_SPK.
While it improved the speaker output quality, it caused the headphone
jack to have an audible "pop" sound when power saving was toggled.
Fixes: 1885ff13d4c4 ("ALSA: hda/realtek: Enable 4-speaker output Dell Precision 5530 laptop")
Signed-off-by: Callum Osmotherly <callum.osmotherly@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Yz0uyN1zwZhnyRD6@piranha
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 568be8aaf8a535f79c4db76cabe17b035aa2584d upstream.
At an error path to release URB buffers and contexts, the driver might
hit a NULL dererence for u->urb pointer, when u->buffer_size has been
already set but the actual URB allocation failed.
Fix it by adding the NULL check of urb. Also, make sure that
buffer_size is cleared after the error path or the close.
Cc: <stable@vger.kernel.org>
Reported-by: Sabri N. Ferreiro <snferreiro1@gmail.com>
Link: https://lore.kernel.org/r/CAKG+3NRjTey+fFfUEGwuxL-pi_=T4cUskYG9OzpzHytF+tzYng@mail.gmail.com
Link: https://lore.kernel.org/r/20220930100129.19445-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6382da0828995af87aa8b8bef28cc61aceb4aff3 upstream.
When the driver hits -ENOMEM at allocating a URB or a buffer, it
aborts and goes to the error path that releases the all previously
allocated resources. However, when -ENOMEM hits at the middle of the
sync EP URB allocation loop, the partially allocated URBs might be
left without released, because ep->nurbs is still zero at that point.
Fix it by setting ep->nurbs at first, so that the error handler loops
over the full URB list.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220930100151.19461-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a70aef7982b012e86dfd39fbb235e76a21ae778a upstream.
The register_mutex taken around the dev_unregister callback call in
snd_rawmidi_free() may potentially lead to a mutex deadlock, when OSS
emulation and a hot unplug are involved.
Since the mutex doesn't protect the actual race (as the registration
itself is already protected by another means), let's drop it.
Link: https://lore.kernel.org/r/CAB7eexJP7w1B0mVgDF0dQ+gWor7UdkiwPczmL7pn91xx8xpzOA@mail.gmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20221011070147.7611-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97d917879d7f92df09c3f21fd54609a8bcd654b2 upstream.
We took sound_oss_mutex around the calls of unregister_sound_special()
at unregistering OSS devices. This may, however, lead to a deadlock,
because we manage the card release via the card's device object, and
the release may happen at unregister_sound_special() call -- which
will take sound_oss_mutex again in turn.
Although the deadlock might be fixed by relaxing the rawmidi mutex in
the previous commit, it's safer to move unregister_sound_special()
calls themselves out of the sound_oss_mutex, too. The call is
race-safe as the function has a spinlock protection by itself.
Link: https://lore.kernel.org/r/CAB7eexJP7w1B0mVgDF0dQ+gWor7UdkiwPczmL7pn91xx8xpzOA@mail.gmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20221011070147.7611-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ff05d4b45dd89b922578dac497dcabf57cf771c6 upstream.
This is a different version of the commit, changed to store
the non-transmitted profile in the elems, and freeing it in
the few places where it's relevant, since that is only the
case when the last argument for parsing (the non-tx BSSID)
is non-NULL.
When we parse a multi-BSSID element, we might point some
element pointers into the allocated nontransmitted_profile.
However, we free this before returning, causing UAF when the
relevant pointers in the parsed elements are accessed.
Fix this by not allocating the scratch buffer separately but
as part of the returned structure instead, that way, there
are no lifetime issues with it.
The scratch buffer introduction as part of the returned data
here is taken from MLO feature work done by Ilan.
This fixes CVE-2022-42719.
Fixes: 5023b14cf4df ("mac80211: support profile split between elements")
Co-developed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is simply not valid and simplifies the next commit.
I'll make a separate patch for this in the current main
tree as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to parse all elements etc. just to find the
authentication challenge - use cfg80211_find_elem() instead.
This also allows us to remove WLAN_EID_CHALLENGE handling
from the element parsing entirely.
Link: https://lore.kernel.org/r/20210920154009.45f9b3a15722.Ice3159ffad03a007d6154cbf1fb3a8c48489e86f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit fd0a6e99b61e6c08fa5cf585d54fd956f70c73a6.
Which was upstream commit 97ef77c52b789ec1411d360ed99dca1efe4b2c81.
The commit is missing dependencies and breaks NFS tests, remove it for
now.
Reported-by: Saeed Mirzamohammadi <saeed.mirzamohammadi@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a17b9841152e7f4621619902b347e2cc39c32996 upstream.
Suspending and resuming the system can sometimes cause the out
URB to get hung after a reset_resume. This causes LED setting
and force feedback to break on resume. To avoid this, just drop
the reset_resume callback so the USB core rebinds xpad to the
wireless pads on resume if a reset happened.
A nice side effect of this change is the LED ring on wireless
controllers is now set correctly on system resume.
Cc: stable@vger.kernel.org
Fixes: 4220f7db1e42 ("Input: xpad - workaround dead irq_out after suspend/ resume")
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Link: https://lore.kernel.org/r/20220818154411.510308-3-rojtberg@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c90b93b5b782891ebfda49d4e5da36632fefd5d1 upstream.
When updating beacon elements in a non-transmitted BSS,
also update the hidden sub-entries to the same beacon
elements, so that a future update through other paths
won't trigger a WARN_ON().
The warning is triggered because the beacon elements in
the hidden BSSes that are children of the BSS should
always be the same as in the parent.
Reported-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 0b8fb8235be8 ("cfg80211: Parsing of Multiple BSSID information in scanning")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1833b6f46d7e2830251a063935ab464256defe22 upstream.
If the tool on the other side (e.g. wmediumd) gets confused
about the rate, we hit a warning in mac80211. Silence that
by effectively duplicating the check here and dropping the
frame silently (in mac80211 it's dropped with the warning).
Reported-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcca852027e5878aec911a347407ecc88d6fff7f upstream.
If a non-transmitted BSS shares enough information (both
SSID and BSSID!) with another non-transmitted BSS of a
different AP, then we can find and update it, and then
try to add it to the non-transmitted BSS list. We do a
search for it on the transmitted BSS, but if it's not
there (but belongs to another transmitted BSS), the list
gets corrupted.
Since this is an erroneous situation, simply fail the
list insertion in this case and free the non-transmitted
BSS.
This fixes CVE-2022-42721.
Reported-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 0b8fb8235be8 ("cfg80211: Parsing of Multiple BSSID information in scanning")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b7808818cb9df6680f98996b8e9a439fa7bcc2f upstream.
There are multiple refcounting bugs related to multi-BSSID:
- In bss_ref_get(), if the BSS has a hidden_beacon_bss, then
the bss pointer is overwritten before checking for the
transmitted BSS, which is clearly wrong. Fix this by using
the bss_from_pub() macro.
- In cfg80211_bss_update() we copy the transmitted_bss pointer
from tmp into new, but then if we release new, we'll unref
it erroneously. We already set the pointer and ref it, but
need to NULL it since it was copied from the tmp data.
- In cfg80211_inform_single_bss_data(), if adding to the non-
transmitted list fails, we unlink the BSS and yet still we
return it, but this results in returning an entry without
a reference. We shouldn't return it anyway if it was broken
enough to not get added there.
This fixes CVE-2022-42720.
Reported-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: a3584f56de1c ("cfg80211: Properly track transmitting and non-transmitting BSS")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 567e14e39e8f8c6997a1378bc3be615afca86063 upstream.
When iterating the elements here, ensure the length byte is
present before checking it to see if the entire element will
fit into the buffer.
Longer term, we should rewrite this code using the type-safe
element iteration macros that check all of this.
Fixes: 0b8fb8235be8 ("cfg80211: Parsing of Multiple BSSID information in scanning")
Reported-by: Soenke Huster <shuster@seemoo.tu-darmstadt.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f033d2becc24aa6bfd2a5c104407963560caabc upstream.
Per spec, the maximum value for the MaxBSSID ('n') indicator is 8,
and the minimum is 1 since a multiple BSSID set with just one BSSID
doesn't make sense (the # of BSSIDs is limited by 2^n).
Limit this in the parsing in both cfg80211 and mac80211, rejecting
any elements with an invalid value.
This fixes potentially bad shifts in the processing of these inside
the cfg80211_gen_new_bssid() function later.
I found this during the investigation of CVE-2022-41674 fixed by the
previous patch.
Fixes: 0b8fb8235be8 ("cfg80211: Parsing of Multiple BSSID information in scanning")
Fixes: 78ac51f81532 ("mac80211: support multi-bssid")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aebe9f4639b13a1f4e9a6b42cdd2e38c617b442d upstream.
In the copy code of the elements, we do the following calculation
to reach the end of the MBSSID element:
/* copy the IEs after MBSSID */
cpy_len = mbssid[1] + 2;
This looks fine, however, cpy_len is a u8, the same as mbssid[1],
so the addition of two can overflow. In this case the subsequent
memcpy() will overflow the allocated buffer, since it copies 256
bytes too much due to the way the allocation and memcpy() sizes
are calculated.
Fix this by using size_t for the cpy_len variable.
This fixes CVE-2022-41674.
Reported-by: Soenke Huster <shuster@seemoo.tu-darmstadt.de>
Tested-by: Soenke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 0b8fb8235be8 ("cfg80211: Parsing of Multiple BSSID information in scanning")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 748bc4dd9e663f23448d8ad7e58c011a67ea1eca upstream.
Previously, the fast pool was dumped into the main pool periodically in
the fast pool's hard IRQ handler. This worked fine and there weren't
problems with it, until RT came around. Since RT converts spinlocks into
sleeping locks, problems cropped up. Rather than switching to raw
spinlocks, the RT developers preferred we make the transformation from
originally doing:
do_some_stuff()
spin_lock()
do_some_other_stuff()
spin_unlock()
to doing:
do_some_stuff()
queue_work_on(some_other_stuff_worker)
This is an ordinary pattern done all over the kernel. However, Sherry
noticed a 10% performance regression in qperf TCP over a 40gbps
InfiniBand card. Quoting her message:
> MT27500 Family [ConnectX-3] cards:
> Infiniband device 'mlx4_0' port 1 status:
> default gid: fe80:0000:0000:0000:0010:e000:0178:9eb1
> base lid: 0x6
> sm lid: 0x1
> state: 4: ACTIVE
> phys state: 5: LinkUp
> rate: 40 Gb/sec (4X QDR)
> link_layer: InfiniBand
>
> Cards are configured with IP addresses on private subnet for IPoIB
> performance testing.
> Regression identified in this bug is in TCP latency in this stack as reported
> by qperf tcp_lat metric:
>
> We have one system listen as a qperf server:
> [root@yourQperfServer ~]# qperf
>
> Have the other system connect to qperf server as a client (in this
> case, it’s X7 server with Mellanox card):
> [root@yourQperfClient ~]# numactl -m0 -N0 qperf 20.20.20.101 -v -uu -ub --time 60 --wait_server 20 -oo msg_size:4K:1024K:*2 tcp_lat
Rather than incur the scheduling latency from queue_work_on, we can
instead switch to running on the next timer tick, on the same core. This
also batches things a bit more -- once per jiffy -- which is okay now
that mix_interrupt_randomness() can credit multiple bits at once.
Reported-by: Sherry Yang <sherry.yang@oracle.com>
Tested-by: Paul Webb <paul.x.webb@oracle.com>
Cc: Sherry Yang <sherry.yang@oracle.com>
Cc: Phillip Goerl <phillip.goerl@oracle.com>
Cc: Jack Vogel <jack.vogel@oracle.com>
Cc: Nicky Veitch <nicky.veitch@oracle.com>
Cc: Colm Harrington <colm.harrington@oracle.com>
Cc: Ramanan Govindarajan <ramanan.govindarajan@oracle.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Sultan Alsawaf <sultan@kerneltoast.com>
Cc: stable@vger.kernel.org
Fixes: 58340f8e952b ("random: defer fast pool mixing to worker")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
