IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
For putting interface into vlan promiscuous mode, we use be_cmd_rx_filter()
and not be_cmd_vlan_config(). So remove the "promiscuous" argument from
be_cmd_vlan_config().
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the vlan u8[] used to track vlan-id
membership to a bit-map as it reduces memory usage.
Signed-off-by: Ravikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a funtion definition or a function call spans more than one
line, ensure that the first argument on the subsequent lines is
aligned to the first column after the opening paranthesis of the
function call.
Also remove unnecessary line wrap.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This be2net patch implements the get/set_rxfh() ethtool hooks.
RSS_CONFIG device command is invoked to set hashkey and indirection table.
It also uses an initial random value for RSS hash key instead of a
hard-coded value as hard-coded values for a hash-key are usually
considered a security risk.
Signed-off-by: Venkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the EEH error recovery path, when a permanent failure occurs,
we clean up adapter structure (i.e. destroy queues etc) by calling
be_clear() and return PCI_ERS_RESULT_DISCONNECT.
After this the stack tries to remove device from bus and calls
be_remove() which invokes netdev_unregister()->be_close().
be_close() operating on destroyed queues results in a
NULL dereference.
This patch fixes this problem by introducing a flag to keep track
of the setup state.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_close() currently waits for a max of 200ms to receive all pending
TX compls. This timeout value was roughly calculated based on 10G
transmission speeds and the TX queue depth. This timeout may not be
enough when the link is operating at lower speeds or in multi-channel/SR-IOV
configs with TX-rate limiting setting.
It is hard to calculate a "proper timeout value" that works in all
configurations. This patch solves this problem by continuing to reap
TX completions till the HW is completely silent for a period of 10ms or
a HW error is detected.
v2: implements the new scheme (as suggested by David Laight) instead of
just waiting longer than 200ms for reaping all completions.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a CONFIG_BE2NET_VXLAN define to control be2net's build
dependency on the VXLAN driver.
Without this fix, the kernel build fails when VxLAN driver is
selected to be built as a module while be2net is built-in.
fixes: c9c47142 ("be2net: csum, tso and rss steering offload support for VxLAN")
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch mainly implements the add/del_vxlan_port() methods by invoking
the needed FW cmds for supporting VxLAN offloads for Skyhawk-R.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the FW cmds needed for VxLAN offloads
on Skyhawk-R:
1) The VxLAN UDP port needs to be configured via the port-desc of
SET_PROFILE_CONFIG_v1 cmd.
This patch re-factors the be_set_profile_config() code (used so far
only for setting VF QoS) to be used to set any type of descriptor.
2) The MANAGE_IFACE_FILTERS cmds is needed to convert a normal interface
into a tunnel interface. This allows for RSS to work even on the inner
TCP/UDP headers of VxLAN traffic.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the bh safe variant with the hard irq safe variant.
We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.
Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace free_skb with dev_kfree_skb_any in be_tx_compl_process as
which can be called in hard irq by netpoll, softirq context
by normal napi polling, and in normal sleepable context
by the network device close method.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN is added by user, adapter->vlans_added is incremented.
But if the VLAN is already programmed in HW, driver ends up
incrementing the counter wrongly.
Increment the counter only if VLAN is not already programmed in the HW.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver creates only a single TXQ on any BE3-R multi-channel
interface.
This patch changes this and creates multiple TXQs on RSS-capable multi-channel
BE3-R interfaces. This change helps improve the TX pps performance on the
affected interface.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allocation size must be be_max_uc() and not "be_max_uc() + 1"
Signed-off-by: Ravikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to control VF's link state by implementing the
ndo_set_vf_link_state() hook.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use GET_PROFILE_CONFIG_V1 cmd even for BE3-R (it's already used for
Lancer-R and Skyhawk-R), to query max-vfs value supported by the FW.
This is needed as on some configs, the value exported in the PCI-config
space is not accurate.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently maps a page for DMA, divides the page into multiple
frags and posts them to the HW. It un-maps the page after data is received
on all the frags of the page. This scheme doesn't work when bounce buffers
are used for DMA (swiotlb=force kernel param).
This patch fixes this problem by calling dma_sync_single_for_cpu() for each
frag (excepting the last one) so that the data is copied from the bounce
buffers. The page is un-mapped only when DMA finishes on the last frag of
the page.
(Thanks Ben H. for suggesting the dma_sync API!)
This patch also renames the "last_page_user" field of be_rx_page_info{}
struct to "last_frag" to improve readability of the fixed code.
Reported-by: Li Fengmao <li.fengmao@zte.com.cn>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of TX workarounds in be_xmit_workarounds() routine
are not applicable (and result in HW errors) to Skyhawk-R chip.
Isolate BE3-R/Lancer specific workarounds to a separate routine.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_padto(), skb_share_check() and __vlan_put_tag() routines free
skb when they return an error. This patch fixes be_xmit_workarounds()
to not free skb again in such cases.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should clear promiscuous bits in adapter->flags while disabling promiscuous
mode. Else we will not put interface back into VLAN promisc mode if the vlans
already added exceeds the maximum limit.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For disabling transparent tagging issue SET_HSW_CONFIG with pvid_valid=1
and pvid=0xFFFF and not with the default pvid as this case would fail in Lancer.
Hence removing the get_hsw_config call from be_vf_setup() as it's
only use of getting default pvid is no longer needed.
Also do proper housekeeping only if the FW command succeeds.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Acked-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently multi-channel configuration is read via the QUERY_FW_CONFIG cmd.
This method has been deprecated by the Skyhawk-R FW. Instead,
GET_PROFILE_CONFIG::port-desc must be used to query this configuration.
This patch also:
a) introduces a few macros to identify certain categories of multi-channel
configs
2) re-factors the be_cmd_set_profile_config() code to be able to read any kind
of desc (and not just the nic-desc.)
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch logs a kernel message when a HW error(SLIPORT_ERROR in Lancer and UE
in BEx/Skyhawk) is detected. The log message for BE3 was missing earlier.
This patch also refactors the code by segregating error-detection and reporting
code for Lancer and BEx/SH.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current logic to put interface into VLAN Promiscous mode is not correct.
We should increment "adapter->vlans_added" before calling be_vid_config().
Also removed some unwanted log messages.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
net/ipv4/tcp_metrics.c
Overlapping changes between the "don't create two tcp metrics objects
with the same key" race fix in net and the addition of the destination
address in the lookup key in net-next.
Minor overlapping changes in bnx2x driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not check value returned by dma_map_page. The patch
fixes this.
v2: Removed the bugfix for non-bug ;-) (thanks Sathya)
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Sathya Perla <Sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans-up wake-on-lan code in the following ways:
1) Removes some driver hacks in be_cmd_get_acpi_wol_cap() that were based
on incorrect assumptions.
2) Uses the adapter->wol_en and wol_cap variables for checking if WoL
is supported and enabled on an interface instead of referring to the
exclusion list via the macro be_is_wol_supported()
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of NTKW_MAC_QUERY cmd has been deprecated for Skyhawk-R.
Replace the last remaining usage in be_vfs_mac_query() routine.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead, use the tail of the RXQ to pick the associated RXQ entry
This fix is required in preparation for supporting RXQ lengths greater than 1K.
For such queues, the frag index in the RX-compl entry is not valid as it is only a 10 bit entry not capable of addressing RXQs longer than 1K.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An earlier commit (f25b119c "Fix error messages while driver load for VFs")
incorrectly set the adapter->cmd_privileges value for VFs (in a
multi-channel config) to MAX_PRIVILEGES. This causes FW cmd failures
and avoidable error logs when certian cmds are issued by a VF.
Also, move the multi-channel hack to be_cmds.c inside
be_cmd_get_fn_privileges() routine.
Fixes: f25b119c "Fix error messages while driver load for VFs"
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ndo_set_mac_addr() call may be issued for a mac-addr that is already
active on an interface. If so, silently ignore the request. Sending such
a request to the FW, causes a "mac collision" error. The error is harmless
but is avoidable noise in the kernel log.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skyhawk-R FW does not support SET/GET_EXT_FAT_CAPABILITIES cmds via which
FW logging level can be controlled. Also, the hack used in BE3 to control
FW logging level via the ethtool interface is not needed in Skyhawk-R.
This patch also cleans up this code by moving be_set/get_fw_log_level()
routines to be_cmds.c where they belong.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
remove new line
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver wrongly assumes 16 EQs/vectors are available for each BE3 PF.
When SR-IOV is enabled, a BE3 PF can support only a max of 8 EQs.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The loopback test FW cmd may need upto 15 seconds to complete on
certain PHYs. This patch also fixes the name of the completion variable
used to synchronize FW cmd completions as it not used by the flashing
cmd alone anymore.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When *only* the default RXQ is used, the RSS policy must be disabled so
that all IP and no-IP traffic is placed into the default RXQ. If not,
IP traffic is dropped.
Also, issue the RSS_CONFIG cmd only if FW advertises RSS capability for
the interface.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During suspend-resume and lancer error recovery we will cleanup and
re-initialize the resources through be_clear() and be_setup() respectively.
During re-initialisation in be_setup(), if be_get_config() fails, we'll again
call be_clear() which will cause a NULL pointer dereference as adapter->pmac_id is
already freed.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Firmware update would be detected by looking at the sliport_error1/
sliport_error2 register values(0x02/0x00). If its not a FW reset the current
messaging would take place. If the error is due to FW reset, log a message to
user that "Firmware update in progress" and also do not log sliport_status and
sliport_error register values.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent be2net commit 6384a4d (adds a support for busy polling)
introduces a regression that results in kernel crash. It incorrectly
modified be_close() so napi_disable() is called only for the first queue.
This breaks a correct pairing of napi_enable/_disable for the rest
of event queues and causes a crash in subsequent be_open() call.
v2: Applied suggestions from Sathya
Fixes: 6384a4d ("be2net: add support for ndo_busy_poll")
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 55485e7b417b640870b14eceec4cfbcb2b3e7a92.
I applied the wrong version of this patch, the right one is coming up
next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent be2net commit 6384a4d (adds a support for busy polling)
introduces a regression that results in kernel crash. It incorrectly
modified be_close() so napi_disable() is called only for the first queue.
This breaks a correct pairing of napi_enable/_disable for the rest
of event queues and causes a crash in subsequent be_open() call.
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On BE3-R, the PF programs the initial MAC address for its VFs. Doing it again
in VF probe, causes a FW error which although harmless generates
an unnecessary error log message.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupts need to be enabled in be_resume, when adapter boots back up from D3cold.
disabling interrupts in be_suspend() just to be symmetric to be_resume().
Signed-off-by: Ravikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Mostly these are fixes for fallout due to merge window changes, as
well as cures for problems that have been with us for a much longer
period of time"
1) Johannes Berg noticed two major deficiencies in our genetlink
registration. Some genetlink protocols we passing in constant
counts for their ops array rather than something like
ARRAY_SIZE(ops) or similar. Also, some genetlink protocols were
using fixed IDs for their multicast groups.
We have to retain these fixed IDs to keep existing userland tools
working, but reserve them so that other multicast groups used by
other protocols can not possibly conflict.
In dealing with these two problems, we actually now use less state
management for genetlink operations and multicast groups.
2) When configuring interface hardware timestamping, fix several
drivers that simply do not validate that the hwtstamp_config value
is one the driver actually supports. From Ben Hutchings.
3) Invalid memory references in mwifiex driver, from Amitkumar Karwar.
4) In dev_forward_skb(), set the skb->protocol in the right order
relative to skb_scrub_packet(). From Alexei Starovoitov.
5) Bridge erroneously fails to use the proper wrapper functions to make
calls to netdev_ops->ndo_vlan_rx_{add,kill}_vid. Fix from Toshiaki
Makita.
6) When detaching a bridge port, make sure to flush all VLAN IDs to
prevent them from leaking, also from Toshiaki Makita.
7) Put in a compromise for TCP Small Queues so that deep queued devices
that delay TX reclaim non-trivially don't have such a performance
decrease. One particularly problematic area is 802.11 AMPDU in
wireless. From Eric Dumazet.
8) Fix crashes in tcp_fastopen_cache_get(), we can see NULL socket dsts
here. Fix from Eric Dumzaet, reported by Dave Jones.
9) Fix use after free in ipv6 SIT driver, from Willem de Bruijn.
10) When computing mergeable buffer sizes, virtio-net fails to take the
virtio-net header into account. From Michael Dalton.
11) Fix seqlock deadlock in ip4_datagram_connect() wrt. statistic
bumping, this one has been with us for a while. From Eric Dumazet.
12) Fix NULL deref in the new TIPC fragmentation handling, from Erik
Hugne.
13) 6lowpan bit used for traffic classification was wrong, from Jukka
Rissanen.
14) macvlan has the same issue as normal vlans did wrt. propagating LRO
disabling down to the real device, fix it the same way. From Michal
Kubecek.
15) CPSW driver needs to soft reset all slaves during suspend, from
Daniel Mack.
16) Fix small frame pacing in FQ packet scheduler, from Eric Dumazet.
17) The xen-netfront RX buffer refill timer isn't properly scheduled on
partial RX allocation success, from Ma JieYue.
18) When ipv6 ping protocol support was added, the AF_INET6 protocol
initialization cleanup path on failure was borked a little. Fix
from Vlad Yasevich.
19) If a socket disconnects during a read/recvmsg/recvfrom/etc that
blocks we can do the wrong thing with the msg_name we write back to
userspace. From Hannes Frederic Sowa. There is another fix in the
works from Hannes which will prevent future problems of this nature.
20) Fix route leak in VTI tunnel transmit, from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
genetlink: make multicast groups const, prevent abuse
genetlink: pass family to functions using groups
genetlink: add and use genl_set_err()
genetlink: remove family pointer from genl_multicast_group
genetlink: remove genl_unregister_mc_group()
hsr: don't call genl_unregister_mc_group()
quota/genetlink: use proper genetlink multicast APIs
drop_monitor/genetlink: use proper genetlink multicast APIs
genetlink: only pass array to genl_register_family_with_ops()
tcp: don't update snd_nxt, when a socket is switched from repair mode
atm: idt77252: fix dev refcnt leak
xfrm: Release dst if this dst is improper for vti tunnel
netlink: fix documentation typo in netlink_set_err()
be2net: Delete secondary unicast MAC addresses during be_close
be2net: Fix unconditional enabling of Rx interface options
net, virtio_net: replace the magic value
ping: prevent NULL pointer dereference on write to msg_name
bnx2x: Prevent "timeout waiting for state X"
bnx2x: prevent CFC attention
bnx2x: Prevent panic during DMAE timeout
...
