IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit d0cfa548db upstream.
When setting Tx sci explicit, the Rx side is expected to use this
sci and not recalculate it from the packet.However, in case of Tx sci
is explicit and send_sci is off, the receiver is wrongly recalculate
the sci from the source MAC address which most likely be different
than the explicit sci.
Fix by preventing such configuration when macsec newlink is established
and return EINVAL error code on such cases.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Link: https://lore.kernel.org/r/1643542672-29403-1-git-send-email-raeds@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cbd27267f upstream.
Apply only valid chip select value. This change fixes case where chip
select is set to initial value of '-1' during probe and PM supend and
subsequent resume can try to use the value with undefined behaviour.
Also in case where gpio based chip select, the check in
bcm_qspi_chip_select() shall prevent undefined behaviour on resume.
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220127185359.27322-1-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b45a7738e upstream.
The polling loop for the register change in iommu_ga_log_enable() needs
to have a udelay() in it. Otherwise the CPU might be faster than the
IOMMU hardware and wrongly trigger the WARN_ON() further down the code
stream. Use a 10us for udelay(), has there is some hardware where
activation of the GA log can take more than a 100ms.
A future optimization should move the activation check of the GA log
to the point where it gets used for the first time. But that is a
bigger change and not suitable for a fix.
Fixes: 8bda0cfbdc ("iommu/amd: Detect and initialize guest vAPIC log")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20220204115537.3894-1-joro@8bytes.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b777d4d9e upstream.
Bounds checking when parsing init scripts embedded in the BIOS reject
access to the last byte. This causes driver initialization to fail on
Apple eMac's with GeForce 2 MX GPUs, leaving the system with no working
console.
This is probably only seen on OpenFirmware machines like PowerPC Macs
because the BIOS image provided by OF is only the used parts of the ROM,
not a power-of-two blocks read from PCI directly so PCs always have
empty bytes at the end that are never accessed.
Signed-off-by: Nick Lopez <github@glowingmonkey.org>
Fixes: 4d4e9907ff ("drm/nouveau/bios: guard against out-of-bounds accesses to image")
Cc: <stable@vger.kernel.org> # v4.10+
Reviewed-by: Ilia Mirkin <imirkin@alum.mit.edu>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220122081906.2633061-1-github@glowingmonkey.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e42e70ad6a upstream.
When packet_setsockopt( PACKET_FANOUT_DATA ) reads po->fanout,
no lock is held, meaning that another thread can change po->fanout.
Given that po->fanout can only be set once during the socket lifetime
(it is only cleared from fanout_release()), we can use
READ_ONCE()/WRITE_ONCE() to document the race.
BUG: KCSAN: data-race in packet_setsockopt / packet_setsockopt
write to 0xffff88813ae8e300 of 8 bytes by task 14653 on cpu 0:
fanout_add net/packet/af_packet.c:1791 [inline]
packet_setsockopt+0x22fe/0x24a0 net/packet/af_packet.c:3931
__sys_setsockopt+0x209/0x2a0 net/socket.c:2180
__do_sys_setsockopt net/socket.c:2191 [inline]
__se_sys_setsockopt net/socket.c:2188 [inline]
__x64_sys_setsockopt+0x62/0x70 net/socket.c:2188
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88813ae8e300 of 8 bytes by task 14654 on cpu 1:
packet_setsockopt+0x691/0x24a0 net/packet/af_packet.c:3935
__sys_setsockopt+0x209/0x2a0 net/socket.c:2180
__do_sys_setsockopt net/socket.c:2191 [inline]
__se_sys_setsockopt net/socket.c:2188 [inline]
__x64_sys_setsockopt+0x62/0x70 net/socket.c:2188
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000000000000000 -> 0xffff888106f8c000
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 14654 Comm: syz-executor.3 Not tainted 5.16.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 47dceb8ecd ("packet: add classic BPF fanout mode")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220201022358.330621-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a504b703bb upstream.
In case almost or all available ports are taken, clash resolution can
take a very long time, resulting in soft lockup.
This can happen when many to-be-natted hosts connect to same
destination:port (e.g. a proxy) and all connections pass the same SNAT.
Pick a random offset in the acceptable range, then try ever smaller
number of adjacent port numbers, until either the limit is reached or a
useable port was found. This results in at most 248 attempts
(128 + 64 + 32 + 16 + 8, i.e. 4 restarts with new search offset)
instead of 64000+,
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ed5943f87 upstream.
This is a leftover from days where single-cpu systems were common:
Store last port used to resolve a clash to use it as a starting point when
the next conflict needs to be resolved.
When we have parallel attempt to connect to same address:port pair,
its likely that both cores end up computing the same "available" port,
as both use same starting port, and newly used ports won't become
visible to other cores until the conntrack gets confirmed later.
One of the cores then has to drop the packet at insertion time because
the chosen new tuple turns out to be in use after all.
Lets simplify this: remove port rover and use a pseudo-random starting
point.
Note that this doesn't make netfilter default to 'fully random' mode;
the 'rover' was only used if NAT could not reuse source port as-is.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 970a5a3ea8 ]
In commit 431280eebe ("ipv4: tcp: send zero IPID for RST and
ACK sent in SYN-RECV and TIME-WAIT state") we took care of some
ctl packets sent by TCP.
It turns out we need to use a similar strategy for SYNACK packets.
By default, they carry IP_DF and IPID==0, but there are ways
to ask them to use the hashed IP ident generator and thus
be used to build off-path attacks.
(Ref: Off-Path TCP Exploits of the Mixed IPID Assignment)
One of this way is to force (before listener is started)
echo 1 >/proc/sys/net/ipv4/ip_no_pmtu_disc
Another way is using forged ICMP ICMP_FRAG_NEEDED
with a very small MTU (like 68) to force a false return from
ip_dont_fragment()
In this patch, ip_build_and_send_pkt() uses the following
heuristics.
1) Most SYNACK packets are smaller than IPV4_MIN_MTU and therefore
can use IP_DF regardless of the listener or route pmtu setting.
2) In case the SYNACK packet is bigger than IPV4_MIN_MTU,
we use prandom_u32() generator instead of the IPv4 hashed ident one.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Ray Che <xijiache@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Cc: Geoff Alexander <alexandg@cs.unm.edu>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a66c5ed539 ]
According to its datasheet, G781 supports a maximum conversion rate value
of 8 (62.5 ms). However, chips labeled G781 and G780 were found to only
support a maximum conversion rate value of 7 (125 ms). On the other side,
chips labeled G781-1 and G784 were found to support a conversion rate value
of 8. There is no known means to distinguish G780 from G781 or G784; all
chips report the same manufacturer ID and chip revision.
Setting the conversion rate register value to 8 on chips not supporting
it causes unexpected behavior since the real conversion rate is set to 0
(16 seconds) if a value of 8 is written into the conversion rate register.
Limit the conversion rate register value to 7 for all G78x chips to avoid
the problem.
Fixes: ae544f64cc ("hwmon: (lm90) Add support for GMT G781")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1d10f8a1f4 upstream.
After commit:7866a621043f ("dev: add per net_device packet type chains"),
we can not get packet types that are bound to a specified net device by
/proc/net/ptype, this patch fix the regression.
Run "tcpdump -i ens192 udp -nns0" Before and after apply this patch:
Before:
[root@localhost ~]# cat /proc/net/ptype
Type Device Function
0800 ip_rcv
0806 arp_rcv
86dd ipv6_rcv
After:
[root@localhost ~]# cat /proc/net/ptype
Type Device Function
ALL ens192 tpacket_rcv
0800 ip_rcv
0806 arp_rcv
86dd ipv6_rcv
v1 -> v2:
- fix the regression rather than adding new /proc API as
suggested by Stephen Hemminger.
Fixes: 7866a62104 ("dev: add per net_device packet type chains")
Signed-off-by: Jianguo Wu <wujianguo@chinatelecom.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1751fc1db3 upstream.
If the file type changes back to being a regular file on the server
between the failed OPEN and our LOOKUP, then we need to re-run the OPEN.
Fixes: 0dd2b474d0 ("nfs: implement i_op->atomic_open()")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac795161c9 upstream.
If the application sets the O_DIRECTORY flag, and tries to open a
regular file, nfs_atomic_open() will punt to doing a regular lookup.
If the server then returns a regular file, we will happily return a
file descriptor with uninitialised open state.
The fix is to return the expected ENOTDIR error in these cases.
Reported-by: Lyu Tao <tao.lyu@epfl.ch>
Fixes: 0dd2b474d0 ("nfs: implement i_op->atomic_open()")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23f57406b8 upstream.
ip_select_ident_segs() has been very conservative about using
the connected socket private generator only for packets with IP_DF
set, claiming it was needed for some VJ compression implementations.
As mentioned in this referenced document, this can be abused.
(Ref: Off-Path TCP Exploits of the Mixed IPID Assignment)
Before switching to pure random IPID generation and possibly hurt
some workloads, lets use the private inet socket generator.
Not only this will remove one vulnerability, this will also
improve performance of TCP flows using pmtudisc==IP_PMTUDISC_DONT
Fixes: 73f156a6e8 ("inetpeer: get rid of ip_id_count")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reported-by: Ray Che <xijiache@gmail.com>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47934e06b6 upstream.
In one net namespace, after creating a packet socket without binding
it to a device, users in other net namespaces can observe the new
`packet_type` added by this packet socket by reading `/proc/net/ptype`
file. This is minor information leakage as packet socket is
namespace aware.
Add a net pointer in `packet_type` to keep the net namespace of
of corresponding packet socket. In `ptype_seq_show`, this net pointer
must be checked when it is not NULL.
Fixes: 2feb27dbe0 ("[NETNS]: Minor information leak via /proc/net/ptype file.")
Signed-off-by: Congyu Liu <liu3101@purdue.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6cee105e7f upstream.
The warning messages can be invoked from the data path for every packet
transmitted through an ip6gre netdev, leading to high CPU utilization.
Fix that by rate limiting the messages.
Fixes: 09c6bbf090 ("[IPV6]: Do mandatory IPv6 tunnel endpoint checks in realtime")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Tested-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26fbe9772b upstream.
The syzbot fuzzer has identified a bug in which processes hang waiting
for usb_kill_urb() to return. It turns out the issue is not unlinking
the URB; that works just fine. Rather, the problem arises when the
wakeup notification that the URB has completed is not received.
The reason is memory-access ordering on SMP systems. In outline form,
usb_kill_urb() and __usb_hcd_giveback_urb() operating concurrently on
different CPUs perform the following actions:
CPU 0 CPU 1
---------------------------- ---------------------------------
usb_kill_urb(): __usb_hcd_giveback_urb():
... ...
atomic_inc(&urb->reject); atomic_dec(&urb->use_count);
... ...
wait_event(usb_kill_urb_queue,
atomic_read(&urb->use_count) == 0);
if (atomic_read(&urb->reject))
wake_up(&usb_kill_urb_queue);
Confining your attention to urb->reject and urb->use_count, you can
see that the overall pattern of accesses on CPU 0 is:
write urb->reject, then read urb->use_count;
whereas the overall pattern of accesses on CPU 1 is:
write urb->use_count, then read urb->reject.
This pattern is referred to in memory-model circles as SB (for "Store
Buffering"), and it is well known that without suitable enforcement of
the desired order of accesses -- in the form of memory barriers -- it
is entirely possible for one or both CPUs to execute their reads ahead
of their writes. The end result will be that sometimes CPU 0 sees the
old un-decremented value of urb->use_count while CPU 1 sees the old
un-incremented value of urb->reject. Consequently CPU 0 ends up on
the wait queue and never gets woken up, leading to the observed hang
in usb_kill_urb().
The same pattern of accesses occurs in usb_poison_urb() and the
failure pathway of usb_hcd_submit_urb().
The problem is fixed by adding suitable memory barriers. To provide
proper memory-access ordering in the SB pattern, a full barrier is
required on both CPUs. The atomic_inc() and atomic_dec() accesses
themselves don't provide any memory ordering, but since they are
present, we can use the optimized smp_mb__after_atomic() memory
barrier in the various routines to obtain the desired effect.
This patch adds the necessary memory barriers.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+76629376e06e2c2ad626@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8K0QYee0Q0Nna2@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b67b31503 upstream.
Two people have reported (and mentioned numerous other reports on the
web) that VIA's VL817 USB-SATA bridge does not work with the uas
driver. Typical log messages are:
[ 3606.232149] sd 14:0:0:0: [sdg] tag#2 uas_zap_pending 0 uas-tag 1 inflight: CMD
[ 3606.232154] sd 14:0:0:0: [sdg] tag#2 CDB: Write(16) 8a 00 00 00 00 00 18 0c c9 80 00 00 00 80 00 00
[ 3606.306257] usb 4-4.4: reset SuperSpeed Plus Gen 2x1 USB device number 11 using xhci_hcd
[ 3606.328584] scsi host14: uas_eh_device_reset_handler success
Surprisingly, the devices do seem to work okay for some other people.
The cause of the differing behaviors is not known.
In the hope of getting the devices to work for the most users, even at
the possible cost of degraded performance for some, this patch adds an
unusual_devs entry for the VL817 to block it from binding to the uas
driver by default. Users will be able to override this entry by means
of a module parameter, if they want.
CC: <stable@vger.kernel.org>
Reported-by: DocMAX <mail@vacharakis.de>
Reported-and-tested-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8IsK2sjlEv1rqU@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8838b2af23 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.2.7.3 states that DC1 (XON) and DC3 (XOFF)
are the control characters defined in ISO/IEC 646. These shall be quoted if
seen in the data stream to avoid interpretation as flow control characters.
ISO/IEC 646 refers to the set of ISO standards described as the ISO
7-bit coded character set for information interchange. Its final version
is also known as ITU T.50.
See https://www.itu.int/rec/T-REC-T.50-199209-I/en
To abide the standard it is needed to quote DC1 and DC3 correctly if these
are seen as data bytes and not as control characters. The current
implementation already tries to enforce this but fails to catch all
defined cases. 3GPP 27.010 chapter 5.2.7.3 clearly states that the most
significant bit shall be ignored for DC1 and DC3 handling. The current
implementation handles only the case with the most significant bit set 0.
Cases in which DC1 and DC3 have the most significant bit set 1 are left
unhandled.
This patch fixes this by masking the data bytes with ISO_IEC_646_MASK (only
the 7 least significant bits set 1) before comparing them with XON
(a.k.a. DC1) and XOFF (a.k.a. DC3) when testing which byte values need
quotation via byte stuffing.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220120101857.2509-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9d967b2ce upstream.
The buffer handling in pm_show_wakelocks() is tricky, and hopefully
correct. Ensure it really is correct by using sysfs_emit_at() which
handles all of the tricky string handling logic in a PAGE_SIZE buffer
for us automatically as this is a sysfs file being read from.
Reviewed-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fc3b7c298 upstream.
udf_expand_file_adinicb() calls directly ->writepage to write data
expanded into a page. This however misses to setup inode for writeback
properly and so we can crash on inode->i_wb dereference when submitting
page for IO like:
BUG: kernel NULL pointer dereference, address: 0000000000000158
#PF: supervisor read access in kernel mode
...
<TASK>
__folio_start_writeback+0x2ac/0x350
__block_write_full_page+0x37d/0x490
udf_expand_file_adinicb+0x255/0x400 [udf]
udf_file_write_iter+0xbe/0x1b0 [udf]
new_sync_write+0x125/0x1c0
vfs_write+0x28e/0x400
Fix the problem by marking the page dirty and going through the standard
writeback path to write the page. Strictly speaking we would not even
have to write the page but we want to catch e.g. ENOSPC errors early.
Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com>
CC: stable@vger.kernel.org
Fixes: 52ebea749a ("writeback: make backing_dev_info host cgroup-specific bdi_writebacks")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea8569194b upstream.
When we fail to expand inode from inline format to a normal format, we
restore inode to contain the original inline formatting but we forgot to
set i_lenAlloc back. The mismatch between i_lenAlloc and i_size was then
causing further problems such as warnings and lost data down the line.
Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com>
CC: stable@vger.kernel.org
Fixes: 7e49b6f248 ("udf: Convert UDF to new truncate calling sequence")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c9db6679b upstream.
Suppose we have an environment with a number of non-NPIV FCP devices
(virtual HBAs / FCP devices / zfcp "adapter"s) sharing the same physical
FCP channel (HBA port) and its I_T nexus. Plus a number of storage target
ports zoned to such shared channel. Now one target port logs out of the
fabric causing an RSCN. Zfcp reacts with an ADISC ELS and subsequent port
recovery depending on the ADISC result. This happens on all such FCP
devices (in different Linux images) concurrently as they all receive a copy
of this RSCN. In the following we look at one of those FCP devices.
Requests other than FSF_QTCB_FCP_CMND can be slow until they get a
response.
Depending on which requests are affected by slow responses, there are
different recovery outcomes. Here we want to fix failed recoveries on port
or adapter level by avoiding recovery requests that can be slow.
We need the cached N_Port_ID for the remote port "link" test with ADISC.
Just before sending the ADISC, we now intentionally forget the old cached
N_Port_ID. The idea is that on receiving an RSCN for a port, we have to
assume that any cached information about this port is stale. This forces a
fresh new GID_PN [FC-GS] nameserver lookup on any subsequent recovery for
the same port. Since we typically can still communicate with the nameserver
efficiently, we now reach steady state quicker: Either the nameserver still
does not know about the port so we stop recovery, or the nameserver already
knows the port potentially with a new N_Port_ID and we can successfully and
quickly perform open port recovery. For the one case, where ADISC returns
successfully, we re-initialize port->d_id because that case does not
involve any port recovery.
This also solves a problem if the storage WWPN quickly logs into the fabric
again but with a different N_Port_ID. Such as on virtual WWPN takeover
during target NPIV failover.
[https://www.redbooks.ibm.com/abstracts/redp5477.html] In that case the
RSCN from the storage FDISC was ignored by zfcp and we could not
successfully recover the failover. On some later failback on the storage,
we could have been lucky if the virtual WWPN got the same old N_Port_ID
from the SAN switch as we still had cached. Then the related RSCN
triggered a successful port reopen recovery. However, there is no
guarantee to get the same N_Port_ID on NPIV FDISC.
Even though NPIV-enabled FCP devices are not affected by this problem, this
code change optimizes recovery time for gone remote ports as a side effect.
The timely drop of cached N_Port_IDs prevents unnecessary slow open port
attempts.
While the problem might have been in code before v2.6.32 commit
799b76d09a ("[SCSI] zfcp: Decouple gid_pn requests from erp") this fix
depends on the gid_pn_work introduced with that commit, so we mark it as
culprit to satisfy fix dependencies.
Note: Point-to-point remote port is already handled separately and gets its
N_Port_ID from the cached peer_d_id. So resetting port->d_id in general
does not affect PtP.
Link: https://lore.kernel.org/r/20220118165803.3667947-1-maier@linux.ibm.com
Fixes: 799b76d09a ("[SCSI] zfcp: Decouple gid_pn requests from erp")
Cc: <stable@vger.kernel.org> #2.6.32+
Suggested-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 663d34c8df upstream.
Currently if z/VM guest is allowed to retrieve hypervisor performance
data globally for all guests (privilege class B) the query is formed in a
way to include all guests but the group name is left empty. This leads to
that z/VM guests which have access control group set not being included
in the results (even local vm).
Change the query group identifier from empty to "any" to retrieve
information about all guests from any groups (or without a group set).
Cc: stable@vger.kernel.org
Fixes: 31cb4bd31a ("[S390] Hypervisor filesystem (s390_hypfs) for z/VM")
Reviewed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 899663be5e upstream.
Check for out-of-bound read was being performed at the end of while
num_reports loop, and would fill journal with false positives. Added
check to beginning of loop processing so that it doesn't get checked
after ptr has been advanced.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: syphyr <syphyr@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stopping tasklet and hrtimer rely on the active state of tasklet and
hrtimer sequentially in bcm_remove_op(), the op object will be freed
if they are all unactive. Assume the hrtimer timeout is short, the
hrtimer cb has been excuted after tasklet conditional judgment which
must be false after last round tasklet_kill() and before condition
hrtimer_active(), it is false when execute to hrtimer_active(). Bug
is triggerd, because the stopping action is end and the op object
will be freed, but the tasklet is scheduled. The resources of the op
object will occur UAF bug.
Move hrtimer_cancel() behind tasklet_kill() and switch 'while () {...}'
to 'do {...} while ()' to fix the op UAF problem.
Fixes: a06393ed03 ("can: bcm: fix hrtimer/tasklet termination in bcm op removal")
Reported-by: syzbot+5ca851459ed04c778d1d@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pass_to_user() eventually calls kref_put() on an ION handle which is
still live, potentially allowing for it to be legitimately freed by
the client.
Prevent this from happening before its final use in both ION_IOC_ALLOC
and ION_IOC_IMPORT.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This separates the kref for ion handles into two components.
Userspace requests through the ioctl will hold at most one
reference to the internally used kref. All additional requests
will increment a separate counter, and the original reference is
only put once that counter hits 0. This protects the kernel from
a poorly behaving userspace.
Signed-off-by: Daniel Rosenberg <drosen@google.com>
[d-cagle@codeaurora.org: Resolve style issues]
Signed-off-by: Dennis Cagle <d-cagle@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a user happens to call ION_IOC_FREE during an ION_IOC_ALLOC
on the just allocated id, and the copy_to_user fails, the cleanup
code will attempt to free an already freed handle.
This adds a wrapper for ion_alloc that adds an ion_handle_get to
avoid this.
Signed-off-by: Daniel Rosenberg <drosen@google.com>
Signed-off-by: Dennis Cagle <d-cagle@codeaurora.org>
Signed-off-by: Patrick Daly <pdaly@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9b58e8c7d upstream.
While in theory multiple unwinders could be compiled in, it does
not make sense in practise. Use a choice to make the unwinder
selection mutually exclusive and mandatory.
Already before this commit it has not been possible to deselect
FRAME_POINTER. Remove the obsolete comment.
Furthermore, to produce a meaningful backtrace with FRAME_POINTER
enabled the kernel needs a specific function prologue:
mov ip, sp
stmfd sp!, {fp, ip, lr, pc}
sub fp, ip, #4
To get to the required prologue gcc uses apcs and no-sched-prolog.
This compiler options are not available on clang, and clang is not
able to generate the required prologue. Make the FRAME_POINTER
config symbol depending on !clang.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1bd5cba33 upstream.
When computing the access permissions of a shadow page, use the effective
permissions of the walk up to that point, i.e. the logic AND of its parents'
permissions. Two guest PxE entries that point at the same table gfn need to
be shadowed with different shadow pages if their parents' permissions are
different. KVM currently uses the effective permissions of the last
non-leaf entry for all non-leaf entries. Because all non-leaf SPTEs have
full ("uwx") permissions, and the effective permissions are recorded only
in role.access and merged into the leaves, this can lead to incorrect
reuse of a shadow page and eventually to a missing guest protection page
fault.
For example, here is a shared pagetable:
pgd[] pud[] pmd[] virtual address pointers
/->pmd1(u--)->pte1(uw-)->page1 <- ptr1 (u--)
/->pud1(uw-)--->pmd2(uw-)->pte2(uw-)->page2 <- ptr2 (uw-)
pgd-| (shared pmd[] as above)
\->pud2(u--)--->pmd1(u--)->pte1(uw-)->page1 <- ptr3 (u--)
\->pmd2(uw-)->pte2(uw-)->page2 <- ptr4 (u--)
pud1 and pud2 point to the same pmd table, so:
- ptr1 and ptr3 points to the same page.
- ptr2 and ptr4 points to the same page.
(pud1 and pud2 here are pud entries, while pmd1 and pmd2 here are pmd entries)
- First, the guest reads from ptr1 first and KVM prepares a shadow
page table with role.access=u--, from ptr1's pud1 and ptr1's pmd1.
"u--" comes from the effective permissions of pgd, pud1 and
pmd1, which are stored in pt->access. "u--" is used also to get
the pagetable for pud1, instead of "uw-".
- Then the guest writes to ptr2 and KVM reuses pud1 which is present.
The hypervisor set up a shadow page for ptr2 with pt->access is "uw-"
even though the pud1 pmd (because of the incorrect argument to
kvm_mmu_get_page in the previous step) has role.access="u--".
- Then the guest reads from ptr3. The hypervisor reuses pud1's
shadow pmd for pud2, because both use "u--" for their permissions.
Thus, the shadow pmd already includes entries for both pmd1 and pmd2.
- At last, the guest writes to ptr4. This causes no vmexit or pagefault,
because pud1's shadow page structures included an "uw-" page even though
its role.access was "u--".
Any kind of shared pagetable might have the similar problem when in
virtual machine without TDP enabled if the permissions are different
from different ancestors.
In order to fix the problem, we change pt->access to be an array, and
any access in it will not include permissions ANDed from child ptes.
The test code is: https://lore.kernel.org/kvm/20210603050537.19605-1-jiangshanlai@gmail.com/
Remember to test it with TDP disabled.
The problem had existed long before the commit 41074d07c7 ("KVM: MMU:
Fix inherited permissions for emulated guest pte updates"), and it
is hard to find which is the culprit. So there is no fixes tag here.
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Message-Id: <20210603052455.21023-1-jiangshanlai@gmail.com>
Cc: stable@vger.kernel.org
Fixes: cea0f0e7ea ("[PATCH] KVM: MMU: Shadow page table caching")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 4.9:
- Keep passing vcpu argument to gpte_access functions
- Adjust filenames, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0780516a18 upstream.
This fixes the new ept_access_test_read_only and ept_access_test_read_write
testcases from vmx.flat.
The problem is that gpte_access moves bits around to switch from EPT
bit order (XWR) to ACC_*_MASK bit order (RWX). This results in an
incorrect exit qualification. To fix this, make pt_access and
pte_access operate on raw PTE values (only with NX flipped to mean
"can execute") and call gpte_access at the end of the walk. This
lets us use pte_access to compute the exit qualification with XWR
bit order.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Xiao Guangrong <xiaoguangrong@tencent.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[bwh: Backported to 4.9:
- There's no support for EPT accessed/dirty bits, so do not use
have_ad flag
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
