IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit ac32292c8552f7e8517be184e65dd09786e991f9 upstream.
Use ioremap as the main implemented function, and defined
ioremap_nocache to it as a deprecated alias.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8ff78f7f773142eb8a8befe5a95dd6858ebd635 upstream.
Some BIOS erroneously specifies write-combining BAR for intel-lpss-pci
in MTRR. This will cause the system to hang during boot. If possible,
this bug could be corrected with a firmware update.
This patch use devm_ioremap_uc to overwrite/ignore the MTRR settings
by forcing the use of strongly uncachable pages for intel-lpss.
The BIOS bug is present on Dell XPS 13 7390 2-in-1:
[ 0.001734] 5 base 4000000000 mask 6000000000 write-combining
4000000000-7fffffffff : PCI Bus 0000:00
4000000000-400fffffff : 0000:00:02.0 (i915)
4010000000-4010000fff : 0000:00:15.0 (intel-lpss-pci)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203485
Cc: <stable@vger.kernel.org> # v4.19+
Tested-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Tuowen Zhao <ztuowen@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Roman Gilg <subdiff@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5932d260a8d85a103bd6c504fbb85ff58b156bf9 upstream.
On ARCTURUS and RENOIR, powerplay is not supported yet.
When plug in or unplug power jack, ACPI event will issue.
Then kernel NULL pointer BUG will be triggered.
Check for NULL pointers before calling.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12dfd78e3a74825e6f0bc8df7ef9f938fbc6bfe3 upstream.
When starting shutdown in sctp_sf_do_dupcook_a(), get the value for
SHUTDOWN Cumulative TSN Ack from the new association, which is
reconstructed from the cookie, instead of the old association, which
the peer doesn't have anymore.
Otherwise the SHUTDOWN is either ignored or replied to with an ABORT
by the peer because CTSN Ack doesn't match the peer's Initial TSN.
Fixes: bdf6fa52f01b ("sctp: handle association restarts when the socket is closed.")
Signed-off-by: Jere Leppänen <jere.leppanen@nokia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3554e54a46125030c534820c297ed7f6c3907e24 ]
The driver is designed to drop Rx packets and reclaim the buffers
when an allocation fails, and the network interface needs to safely
handle this packet loss. Therefore, an allocation failure of Rx
SKBs is relatively benign.
However, the output of the warning message occurs with a high
scheduling priority that can cause excessive jitter/latency for
other high priority processing.
This commit suppresses the warning messages to prevent scheduling
problems while retaining the failure count in the statistics of
the network interface.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecaeceb8a8a145d93c7e136f170238229165348f ]
The driver is designed to drop Rx packets and reclaim the buffers
when an allocation fails, and the network interface needs to safely
handle this packet loss. Therefore, an allocation failure of Rx
SKBs is relatively benign.
However, the output of the warning message occurs with a high
scheduling priority that can cause excessive jitter/latency for
other high priority processing.
This commit suppresses the warning messages to prevent scheduling
problems while retaining the failure count in the statistics of
the network interface.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5990cdee689c6885b27c6d969a3d58b09002b0bc ]
0day reports over and over on an powerpc randconfig with clang:
lib/mpi/generic_mpih-mul1.c:37:13: error: invalid use of a cast in a
inline asm context requiring an l-value: remove the cast or build with
-fheinous-gnu-extensions
Remove the superfluous casts, which have been done previously for x86
and arm32 in commit dea632cadd12 ("lib/mpi: fix build with clang") and
commit 7b7c1df2883d ("lib/mpi/longlong.h: fix building with 32-bit
x86").
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://github.com/ClangBuiltLinux/linux/issues/991
Link: https://lore.kernel.org/r/20200413195041.24064-1-natechancellor@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e461bc9f9ab105637b86065d24b0b83f182d477c ]
Sed broke on some strings as it used colon as a separator.
I made it more robust by using \001, which is legit POSIX AFAIK.
E.g. ./config --set-str CONFIG_USBNET_DEVADDR "de:ad:be:ef:00:01"
failed with: sed: -e expression #1, char 55: unknown option to `s'
Signed-off-by: Jeremie Francois (on alpha) <jeremie.francois@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ebf6da9db1b2a20bb86cc1bee2552e894d03308 ]
Switching tracers include instruction patching. To prevent that a
instruction is patched while it's read the instruction patching is done
in stop_machine 'context'. This also means that any function called
during stop_machine must not be traced. Thus add 'notrace' to all
functions called within stop_machine.
Fixes: 1ec2772e0c3c ("s390/diag: add a statistic for diagnose calls")
Fixes: 38f2c691a4b3 ("s390: improve wait logic of stop_machine")
Fixes: 4ecf0a43e729 ("processor: get rid of cpu_relax_yield")
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fada37f6f62995cc449b36ebba1220594bfe55fe ]
We use a spinlock while we are reading and accessing the destination address for a server.
We need to also use this spinlock to protect when we are modifying this address from
reconn_set_ipaddr().
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54cb6221688660670a2e430892d7f4e6370263b8 ]
Fix the rsnd_ssi_stop function to skip disabling the individual SSIs of
a multi-SSI setup, as the actual stop is performed by rsnd_ssiu_stop_gen2
- the same logic as in rsnd_ssi_start. The attempt to disable these SSIs
was harmless, but caused a "status check failed" message to be printed
for every SSI in the multi-SSI setup.
The disabling of interrupts is still performed, as they are enabled for
all SSIs in rsnd_ssi_init, but care is taken to not accidentally set the
EN bit for an SSI where it was not set by rsnd_ssi_start.
Signed-off-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20200417153017.1744454-3-matthias.blankertz@cetitec.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c258657ddfe81b4fc0183378d800c97ba0b7cdd ]
The master SSI of a multi-SSI setup was attached both to the
RSND_MOD_SSI slot and the RSND_MOD_SSIP slot of the rsnd_dai_stream.
This is not correct wrt. the meaning of being "parent" in the rest of
the SSI code, where it seems to indicate an SSI that provides clock and
word sync but is not transmitting/receiving audio data.
Not treating the multi-SSI master as parent allows removal of various
special cases to the rsnd_ssi_is_parent conditions introduced in commit
a09fb3f28a60 ("ASoC: rsnd: Fix parent SSI start/stop in multi-SSI mode").
It also fixes the issue that operations performed via rsnd_dai_call()
were performed twice for the master SSI. This caused some "status check
failed" spam when stopping a multi-SSI stream as the driver attempted to
stop the master SSI twice.
Signed-off-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20200417153017.1744454-2-matthias.blankertz@cetitec.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91a2559c1dc5b0f7e1256d42b1508935e8eabfbf ]
In fine adjustement mode, which is the current default, the sub-second
increment register is the number of nanoseconds that will be added to
the clock when the accumulator overflows. At each clock cycle, the
value of the addend register is added to the accumulator.
Currently, we use 20ns = 1e09ns / 50MHz as this value whatever the
frequency of the ptp clock actually is.
The adjustment is then done on the addend register, only incrementing
every X clock cycles X being the ratio between 50MHz and ptp_clock_rate
(addend = 2^32 * 50MHz/ptp_clock_rate).
This causes the following issues :
- In case the frequency of the ptp clock is inferior or equal to 50MHz,
the addend value calculation will overflow and the default
addend value will be set to 0, causing the clock to not work at
all. (For instance, for ptp_clock_rate = 50MHz, addend = 2^32).
- The resolution of the timestamping clock is limited to 20ns while it
is not needed, thus limiting the accuracy of the timestamping to
20ns.
Fix this by setting sub-second increment to 2e09ns / ptp_clock_rate.
It will allow to reach the minimum possible frequency for
ptp_clk_ref, which is 5MHz for GMII 1000Mps Full-Duplex by setting the
sub-second-increment to a higher value. For instance, for 25MHz, it
gives ssinc = 80ns and default_addend = 2^31.
It will also allow to use a lower value for sub-second-increment, thus
improving the timestamping accuracy with frequencies higher than
100MHz, for instance, for 200MHz, ssinc = 10ns and default_addend =
2^31.
v1->v2:
- Remove modifications to the calculation of default addend, which broke
compatibility with clock frequencies for which 2000000000 / ptp_clk_freq
is not an integer.
- Modify description according to discussions.
Signed-off-by: Julien Beraud <julien.beraud@orolia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15ce30609d1e88d42fb1cd948f453e6d5f188249 ]
There are 2 registers to write to enable a ptp ref clock coming from the
fpga.
One that enables the usage of the clock from the fpga for emac0 and emac1
as a ptp ref clock, and the other to allow signals from the fpga to reach
emac0 and emac1.
Currently, if the dwmac-socfpga has phymode set to PHY_INTERFACE_MODE_MII,
PHY_INTERFACE_MODE_GMII, or PHY_INTERFACE_MODE_SGMII, both registers will
be written and the ptp ref clock will be set as coming from the fpga.
Separate the 2 register writes to only enable signals from the fpga to
reach emac0 or emac1 when ptp ref clock is not coming from the fpga.
Signed-off-by: Julien Beraud <julien.beraud@orolia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7717cbec172c3554d470023b4020d5781961187e ]
i2400mu_bus_bm_wait_for_ack() invokes usb_get_urb(), which increases the
refcount of the "notif_urb".
When i2400mu_bus_bm_wait_for_ack() returns, local variable "notif_urb"
becomes invalid, so the refcount should be decreased to keep refcount
balanced.
The issue happens in all paths of i2400mu_bus_bm_wait_for_ack(), which
forget to decrease the refcnt increased by usb_get_urb(), causing a
refcnt leak.
Fix this issue by calling usb_put_urb() before the
i2400mu_bus_bm_wait_for_ack() returns.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbc25dadc7ed19f9d6b2e30980f0eb4c741bb8bf ]
Initialize thermal controller fields in the PowerPlay table for Hawaii
GPUs, so that fan speeds are reported.
Signed-off-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 326b509238171d37402dbe308e154cc234ed1960 ]
If we don't find any pcm, pcm will point at address at an offset from
the the list head and not a meaningful structure. Fix this by returning
correct pcm if found and NULL if not. Found with coccinelle.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20200415162849.308-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b94e164759b82d0c1c80d4b1c8f12c9bee83f11d ]
The HDMI?_SEL register maps up to four stereo SSI data lanes onto the
sdata[0..3] inputs of the HDMI output block. The upper half of the
register contains four blocks of 4 bits, with the most significant
controlling the sdata3 line and the least significant the sdata0 line.
The shift calculation has an off-by-one error, causing the parent SSI to
be mapped to sdata3, the first multi-SSI child to sdata0 and so forth.
As the parent SSI transmits the stereo L/R channels, and the HDMI core
expects it on the sdata0 line, this causes no audio to be output when
playing stereo audio on a multichannel capable HDMI out, and
multichannel audio has permutated channels.
Fix the shift calculation to map the parent SSI to sdata0, the first
child to sdata1 etc.
Signed-off-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20200415141017.384017-3-matthias.blankertz@cetitec.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a09fb3f28a60ba3e928a1fa94b0456780800299d ]
The parent SSI of a multi-SSI setup must be fully setup, started and
stopped since it is also part of the playback/capture setup. So only
skip the SSI (as per commit 203cdf51f288 ("ASoC: rsnd: SSI parent cares
SWSP bit") and commit 597b046f0d99 ("ASoC: rsnd: control SSICR::EN
correctly")) if the SSI is parent outside of a multi-SSI setup.
Signed-off-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20200415141017.384017-2-matthias.blankertz@cetitec.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d94ea5319813658ad5861d161ae16a194c2abf88 ]
Currently the calculation of max packet size limit for IN endpoints is
too restrictive. This prevents a matching of a capable hardware endpoint
during configuration. Below is the minimum recommended HW configuration
to support a particular endpoint setup from the databook:
For OUT endpoints, the databook recommended the minimum RxFIFO size to
be at least 3x MaxPacketSize + 3x setup packets size (8 bytes each) +
clock crossing margin (16 bytes).
For IN endpoints, the databook recommended the minimum TxFIFO size to be
at least 3x MaxPacketSize for endpoints that support burst. If the
endpoint doesn't support burst or when the device is operating in USB
2.0 mode, a minimum TxFIFO size of 2x MaxPacketSize is recommended.
Base on these recommendations, we can calculate the MaxPacketSize limit
of each endpoint. This patch revises the IN endpoint MaxPacketSize limit
and also sets the MaxPacketSize limit for OUT endpoints.
Reference: Databook 3.30a section 3.2.2 and 3.2.3
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa7812737f2877e192d57626cbe8825cc7cf6de9 ]
As mentioned slightly out of patch context in the code, there
is no reset routine for the chip. On boards where the chip is
supplied by a fixed regulator, it might not even be resetted
during (e.g. watchdog) reboot and can be in any state.
If the device is probed with VAG enabled, the driver's probe
routine will generate a loud pop sound when ANA_POWER is
being programmed. Avoid this by properly disabling just the
VAG bit and waiting the required power down time.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Fabio Estevam <festivem@gmail.com>
Link: https://lore.kernel.org/r/20200414181140.145825-1-sebastian.reichel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b87080eab4c1377706c113fc9c0157f19ea8fed1 ]
After successfully running the IPC msgque test once, subsequent runs
result in a test failure:
$ sudo ./run_kselftest.sh
TAP version 13
1..1
# selftests: ipc: msgque
# Failed to get stats for IPC queue with id 0
# Failed to dump queue: -22
# Bail out!
# # Pass 0 Fail 0 Xfail 0 Xpass 0 Skip 0 Error 0
not ok 1 selftests: ipc: msgque # exit=1
The dump_queue() function loops through the possible message queue index
values using calls to msgctl(kern_id, MSG_STAT, ...) where kern_id
represents the index value. The first time the test is ran, the initial
index value of 0 is valid and the test is able to complete. The index
value of 0 is not valid in subsequent test runs and the loop attempts to
try index values of 1, 2, 3, and so on until a valid index value is
found that corresponds to the message queue created earlier in the test.
The msgctl() syscall returns -1 and sets errno to EINVAL when invalid
index values are used. The test failure is caused by incorrectly
comparing errno to -EINVAL when cycling through possible index values.
Fix invalid test failures on subsequent runs of the msgque test by
correctly comparing errno values to a non-negated EINVAL.
Fixes: 3a665531a3b7 ("selftests: IPC message queue copy feature test")
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3677fc3d68dd942c92de52f0bd9dd8b472a40e6 ]
Function pcm_new_ver can fail, so we should check it's return value and
handle possible error.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200327204729.397-6-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit dead1c845dbe97e0061dae2017eaf3bd8f8f06ee upstream.
The pseries platform uses the PCI_PROBE_DEVTREE method of PCI probing
which reads "assigned-addresses" of every PCI device and initializes
the device resources. However if the property is missing or zero sized,
then there is no fallback of any kind and the PCI resources remain
undiscovered, i.e. pdev->resource[] array remains empty.
This adds a fallback which parses the "reg" property in pretty much same
way except it marks resources as "unset" which later make Linux assign
those resources proper addresses.
This has an effect when:
1. a hypervisor failed to assign any resource for a device;
2. /chosen/linux,pci-probe-only=0 is in the DT so the system may try
assigning a resource.
Neither is likely to happen under PowerVM.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b841030625cde5f784dd62aec72d6a766faae70 upstream.
Ning Bo reported an abnormal 2-second gap when booting Kata container [1].
The unconditional timeout was caused by VSOCK_DEFAULT_CONNECT_TIMEOUT of
connecting from the client side. The vhost vsock client tries to connect
an initializing virtio vsock server.
The abnormal flow looks like:
host-userspace vhost vsock guest vsock
============== =========== ============
connect() --------> vhost_transport_send_pkt_work() initializing
| vq->private_data==NULL
| will not be queued
V
schedule_timeout(2s)
vhost_vsock_start() <--------- device ready
set vq->private_data
wait for 2s and failed
connect() again vq->private_data!=NULL recv connecting pkt
Details:
1. Host userspace sends a connect pkt, at that time, guest vsock is under
initializing, hence the vhost_vsock_start has not been called. So
vq->private_data==NULL, and the pkt is not been queued to send to guest
2. Then it sleeps for 2s
3. After guest vsock finishes initializing, vq->private_data is set
4. When host userspace wakes up after 2s, send connecting pkt again,
everything is fine.
As suggested by Stefano Garzarella, this fixes it by additional kicking the
send_pkt worker in vhost_vsock_start once the virtio device is started. This
makes the pending pkt sent again.
After this patch, kata-runtime (with vsock enabled) boot time is reduced
from 3s to 1s on a ThunderX2 arm64 server.
[1] https://github.com/kata-containers/runtime/issues/1917
Reported-by: Ning Bo <n.b@live.com>
Suggested-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Jia He <justin.he@arm.com>
Link: https://lore.kernel.org/r/20200501043840.186557-1-justin.he@arm.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ddca1092c4324c89cf692b5efe655aa251864b51 upstream.
The recent commit 0d84c3e6a5b2 ("mmc: core: Convert to
mmc_poll_for_busy() for erase/trim/discard") makes use of the
->card_busy() op for SD cards. This uncovered that the ->card_busy() op
in the Meson SDIO driver was never working right:
while polling the busy status with ->card_busy()
meson_mx_mmc_card_busy() reads only one of the two MESON_MX_SDIO_IRQC
register values 0x1f001f10 or 0x1f003f10. This translates to "three out
of four DAT lines are HIGH" and "all four DAT lines are HIGH", which
is interpreted as "the card is busy".
It turns out that no situation can be observed where all four DAT lines
are LOW, meaning the card is not busy anymore. Upon further research the
3.10 vendor driver for this controller does not implement the
->card_busy() op.
Remove the ->card_busy() op from the meson-mx-sdio driver since it is
not working. At the time of writing this patch it is not clear what's
needed to make the ->card_busy() implementation work with this specific
controller hardware. For all use-cases which have previously worked the
MMC_CAP_WAIT_WHILE_BUSY flag is now taking over, even if we don't have
a ->card_busy() op anymore.
Fixes: ed80a13bb4c4c9 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200416183513.993763-3-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e53b868b3cf5beeaa2f851ec6740112bf4d6a8cb upstream.
The Meson SDIO controller uses the DAT0 lane for hardware busy
detection. Set MMC_CAP_WAIT_WHILE_BUSY accordingly. This fixes
the following error observed with Linux 5.7 (pre-rc-1):
mmc1: Card stuck being busy! __mmc_poll_for_busy
blk_update_request: I/O error, dev mmcblk1, sector 17111080 op
0x3:(DISCARD) flags 0x0 phys_seg 1 prio class 0
Fixes: ed80a13bb4c4c9 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200416183513.993763-2-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d8cb58691f85cef687512262acb2c7109ee4868 upstream.
MSM sd host controller is capable of HW busy detection of device busy
signaling over DAT0 line. And it requires the R1B response for commands
that have this response associated with them.
So set the below two host capabilities for qcom SDHC.
- MMC_CAP_WAIT_WHILE_BUSY
- MMC_CAP_NEED_RSP_BUSY
Recent development of the mmc core in regards to this, revealed this as
being a potential bug, hence the stable tag.
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1587363626-20413-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a8eb6b373c2af6533c13d1ea11f504e5010ed9a upstream.
BIOS writers have begun the practice of setting 40 ohm eMMC driver strength
even though the eMMC may not support it, on the assumption that the kernel
will validate the value against the eMMC (Extended CSD DRIVER_STRENGTH
[offset 197]) and revert to the default 50 ohm value if 40 ohm is invalid.
This is done to avoid changing the value for different boards.
Putting aside the merits of this approach, it is clear the eMMC's mask
of supported driver strengths is more reliable than the value provided
by BIOS. Add validation accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 51ced59cc02e ("mmc: sdhci-pci: Use ACPI DSM to get driver strength for some Intel devices")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200422111629.4899-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb32e1987bc55ce1db400faf47d85891da3c9b9f upstream.
For some reason the Host Control2 register of the Xenon SDHCI controller
sometimes reports the bit representing 1.8V signaling as 0 when read
after it was written as 1. Subsequent read reports 1.
This causes the sdhci_start_signal_voltage_switch function to report
1.8V regulator output did not become stable
When CONFIG_PM is enabled, the host is suspended and resumend many
times, and in each resume the switch to 1.8V is called, and so the
kernel log reports this message annoyingly often.
Do an empty read of the Host Control2 register in Xenon's
.voltage_switch method to circumvent this.
This patch fixes this particular problem on Turris MOX.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: 8d876bf472db ("mmc: sdhci-xenon: wait 5ms after set 1.8V...")
Cc: stable@vger.kernel.org # v4.16+
Link: https://lore.kernel.org/r/20200420080444.25242-1-marek.behun@nic.cz
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1ac62a7ac386d76968af5f374a4a7a82a35fe31 upstream.
Open-coding a timeout loop invariably leads to errors with handling
the timeout properly in one corner case or another. In the case of
cqhci we might report "CQE stuck on" even if it wasn't stuck on.
You'd just need this sequence of events to happen in cqhci_off():
1. Call ktime_get().
2. Something happens to interrupt the CPU for > 100 us (context switch
or interrupt).
3. Check time and; set "timed_out" to true since > 100 us.
4. Read CQHCI_CTL.
5. Both "reg & CQHCI_HALT" and "timed_out" are true, so break.
6. Since "timed_out" is true, falsely print the error message.
Rather than fixing the polling loop, use readx_poll_timeout() like
many people do. This has been time tested to handle the corner cases.
Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200413162717.1.Idece266f5c8793193b57a1ddb1066d030c6af8e0@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcc99734d1d4ced30167eb02e17f656735cb9928 upstream.
[BUG]
One run of btrfs/063 triggered the following lockdep warning:
============================================
WARNING: possible recursive locking detected
5.6.0-rc7-custom+ #48 Not tainted
--------------------------------------------
kworker/u24:0/7 is trying to acquire lock:
ffff88817d3a46e0 (sb_internal#2){.+.+}, at: start_transaction+0x66c/0x890 [btrfs]
but task is already holding lock:
ffff88817d3a46e0 (sb_internal#2){.+.+}, at: start_transaction+0x66c/0x890 [btrfs]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(sb_internal#2);
lock(sb_internal#2);
*** DEADLOCK ***
May be due to missing lock nesting notation
4 locks held by kworker/u24:0/7:
#0: ffff88817b495948 ((wq_completion)btrfs-endio-write){+.+.}, at: process_one_work+0x557/0xb80
#1: ffff888189ea7db8 ((work_completion)(&work->normal_work)){+.+.}, at: process_one_work+0x557/0xb80
#2: ffff88817d3a46e0 (sb_internal#2){.+.+}, at: start_transaction+0x66c/0x890 [btrfs]
#3: ffff888174ca4da8 (&fs_info->reloc_mutex){+.+.}, at: btrfs_record_root_in_trans+0x83/0xd0 [btrfs]
stack backtrace:
CPU: 0 PID: 7 Comm: kworker/u24:0 Not tainted 5.6.0-rc7-custom+ #48
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
Workqueue: btrfs-endio-write btrfs_work_helper [btrfs]
Call Trace:
dump_stack+0xc2/0x11a
__lock_acquire.cold+0xce/0x214
lock_acquire+0xe6/0x210
__sb_start_write+0x14e/0x290
start_transaction+0x66c/0x890 [btrfs]
btrfs_join_transaction+0x1d/0x20 [btrfs]
find_free_extent+0x1504/0x1a50 [btrfs]
btrfs_reserve_extent+0xd5/0x1f0 [btrfs]
btrfs_alloc_tree_block+0x1ac/0x570 [btrfs]
btrfs_copy_root+0x213/0x580 [btrfs]
create_reloc_root+0x3bd/0x470 [btrfs]
btrfs_init_reloc_root+0x2d2/0x310 [btrfs]
record_root_in_trans+0x191/0x1d0 [btrfs]
btrfs_record_root_in_trans+0x90/0xd0 [btrfs]
start_transaction+0x16e/0x890 [btrfs]
btrfs_join_transaction+0x1d/0x20 [btrfs]
btrfs_finish_ordered_io+0x55d/0xcd0 [btrfs]
finish_ordered_fn+0x15/0x20 [btrfs]
btrfs_work_helper+0x116/0x9a0 [btrfs]
process_one_work+0x632/0xb80
worker_thread+0x80/0x690
kthread+0x1a3/0x1f0
ret_from_fork+0x27/0x50
It's pretty hard to reproduce, only one hit so far.
[CAUSE]
This is because we're calling btrfs_join_transaction() without re-using
the current running one:
btrfs_finish_ordered_io()
|- btrfs_join_transaction() <<< Call #1
|- btrfs_record_root_in_trans()
|- btrfs_reserve_extent()
|- btrfs_join_transaction() <<< Call #2
Normally such btrfs_join_transaction() call should re-use the existing
one, without trying to re-start a transaction.
But the problem is, in btrfs_join_transaction() call #1, we call
btrfs_record_root_in_trans() before initializing current::journal_info.
And in btrfs_join_transaction() call #2, we're relying on
current::journal_info to avoid such deadlock.
[FIX]
Call btrfs_record_root_in_trans() after we have initialized
current::journal_info.
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f135cea30de5f74d5bfb5116682073841fb4af8f upstream.
When we have an inode with a prealloc extent that starts at an offset
lower than the i_size and there is another prealloc extent that starts at
an offset beyond i_size, we can end up losing part of the first prealloc
extent (the part that starts at i_size) and have an implicit hole if we
fsync the file and then have a power failure.
Consider the following example with comments explaining how and why it
happens.
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
# Create our test file with 2 consecutive prealloc extents, each with a
# size of 128Kb, and covering the range from 0 to 256Kb, with a file
# size of 0.
$ xfs_io -f -c "falloc -k 0 128K" /mnt/foo
$ xfs_io -c "falloc -k 128K 128K" /mnt/foo
# Fsync the file to record both extents in the log tree.
$ xfs_io -c "fsync" /mnt/foo
# Now do a redudant extent allocation for the range from 0 to 64Kb.
# This will merely increase the file size from 0 to 64Kb. Instead we
# could also do a truncate to set the file size to 64Kb.
$ xfs_io -c "falloc 0 64K" /mnt/foo
# Fsync the file, so we update the inode item in the log tree with the
# new file size (64Kb). This also ends up setting the number of bytes
# for the first prealloc extent to 64Kb. This is done by the truncation
# at btrfs_log_prealloc_extents().
# This means that if a power failure happens after this, a write into
# the file range 64Kb to 128Kb will not use the prealloc extent and
# will result in allocation of a new extent.
$ xfs_io -c "fsync" /mnt/foo
# Now set the file size to 256K with a truncate and then fsync the file.
# Since no changes happened to the extents, the fsync only updates the
# i_size in the inode item at the log tree. This results in an implicit
# hole for the file range from 64Kb to 128Kb, something which fsck will
# complain when not using the NO_HOLES feature if we replay the log
# after a power failure.
$ xfs_io -c "truncate 256K" -c "fsync" /mnt/foo
So instead of always truncating the log to the inode's current i_size at
btrfs_log_prealloc_extents(), check first if there's a prealloc extent
that starts at an offset lower than the i_size and with a length that
crosses the i_size - if there is one, just make sure we truncate to a
size that corresponds to the end offset of that prealloc extent, so
that we don't lose the part of that extent that starts at i_size if a
power failure happens.
A test case for fstests follows soon.
Fixes: 31d11b83b96f ("Btrfs: fix duplicate extents after fsync of file with prealloc extents")
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb73974172ffaaf57a7c42f35424d9aece1a5af6 upstream.
Fix the SELinux netlink_send hook to properly handle multiple netlink
messages in a single sk_buff; each message is parsed and subject to
SELinux access control. Prior to this patch, SELinux only inspected
the first message in the sk_buff.
Cc: stable@vger.kernel.org
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Stephen Smalley <stephen.smalley.work@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9f960201249f20deea586b4ec814669b4c6b1c0 upstream.
Under some circumstances, i.e. when test is still running and about to
time out and user runs, for example,
grep -H . /sys/module/dmatest/parameters/*
the iterations parameter is not respected and test is going on and on until
user gives
echo 0 > /sys/module/dmatest/parameters/run
This is not what expected.
The history of this bug is interesting. I though that the commit
2d88ce76eb98 ("dmatest: add a 'wait' parameter")
is a culprit, but looking closer to the code I think it simple revealed the
broken logic from the day one, i.e. in the commit
0a2ff57d6fba ("dmaengine: dmatest: add a maximum number of test iterations")
which adds iterations parameter.
So, to the point, the conditional of checking the thread to be stopped being
first part of conjunction logic prevents to check iterations. Thus, we have to
always check both conditions to be able to stop after given iterations.
Since it wasn't visible before second commit appeared, I add a respective
Fixes tag.
Fixes: 2d88ce76eb98 ("dmatest: add a 'wait' parameter")
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20200424161147.16895-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7648f939cb919b9d15c21fff8cd9eba908d595dc upstream.
nfs3_set_acl keeps track of the acl it allocated locally to determine if an acl
needs to be released at the end. This results in a memory leak when the
function allocates an acl as well as a default acl. Fix by releasing acls
that differ from the acl originally passed into nfs3_set_acl.
Fixes: b7fa0554cf1b ("[PATCH] NFS: Add support for NFSv3 ACLs")
Reported-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ce00760a84848d008554c693ceb6286f4d9c509 upstream.
gcc-10 points out a few instances of suspicious integer arithmetic
leading to value truncation:
sound/isa/opti9xx/opti92x-ad1848.c: In function 'snd_opti9xx_configure':
sound/isa/opti9xx/opti92x-ad1848.c:322:43: error: overflow in conversion from 'int' to 'unsigned char' changes value from '(int)snd_opti9xx_read(chip, 3) & -256 | 240' to '240' [-Werror=overflow]
322 | (snd_opti9xx_read(chip, reg) & ~(mask)) | ((value) & (mask)))
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~
sound/isa/opti9xx/opti92x-ad1848.c:351:3: note: in expansion of macro 'snd_opti9xx_write_mask'
351 | snd_opti9xx_write_mask(chip, OPTi9XX_MC_REG(3), 0xf0, 0xff);
| ^~~~~~~~~~~~~~~~~~~~~~
sound/isa/opti9xx/miro.c: In function 'snd_miro_configure':
sound/isa/opti9xx/miro.c:873:40: error: overflow in conversion from 'int' to 'unsigned char' changes value from '(int)snd_miro_read(chip, 3) & -256 | 240' to '240' [-Werror=overflow]
873 | (snd_miro_read(chip, reg) & ~(mask)) | ((value) & (mask)))
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~
sound/isa/opti9xx/miro.c:1010:3: note: in expansion of macro 'snd_miro_write_mask'
1010 | snd_miro_write_mask(chip, OPTi9XX_MC_REG(3), 0xf0, 0xff);
| ^~~~~~~~~~~~~~~~~~~
These are all harmless here as only the low 8 bit are passed down
anyway. Change the macros to inline functions to make the code
more readable and also avoid the warning.
Strictly speaking those functions also need locking to make the
read/write pair atomic, but it seems unlikely that anyone would
still run into that issue.
Fixes: 1841f613fd2e ("[ALSA] Add snd-miro driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200429190216.85919-1-arnd@arndb.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b74aa02d7a30ee5e262072a7d6e8deff10b37924 upstream.
Currently, system fails to boot because the legacy interrupt remapping
mode does not enable 128-bit IRTE (GA), which is required for x2APIC
support.
Fix by using AMD_IOMMU_GUEST_IR_LEGACY_GA mode when booting with
kernel option amd_iommu_intr=legacy instead. The initialization
logic will check GASup and automatically fallback to using
AMD_IOMMU_GUEST_IR_LEGACY if GA mode is not supported.
Fixes: 3928aa3f5775 ("iommu/amd: Detect and enable guest vAPIC support")
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/1587562202-14183-1-git-send-email-suravee.suthikulpanit@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d2ff149b263c9325875726a7804a0c75ef7112e upstream.
SBC4 specifies that WRITE SAME requests with the UNMAP bit set to zero
"shall perform the specified write operation to each LBA specified by the
command". Commit 2237498f0b5c ("target/iblock: Convert WRITE_SAME to
blkdev_issue_zeroout") modified the iblock backend to call
blkdev_issue_zeroout() when handling WRITE SAME requests with UNMAP=0 and a
zero data segment.
The iblock blkdev_issue_zeroout() call incorrectly provides a flags
parameter of 0 (bool false), instead of BLKDEV_ZERO_NOUNMAP. The bool
false parameter reflects the blkdev_issue_zeroout() API prior to commit
ee472d835c26 ("block: add a flags argument to (__)blkdev_issue_zeroout")
which was merged shortly before 2237498f0b5c.
Link: https://lore.kernel.org/r/20200419163109.11689-1-ddiss@suse.de
Fixes: 2237498f0b5c ("target/iblock: Convert WRITE_SAME to blkdev_issue_zeroout")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b52649aee6243ea661905bdc5fbe28cc5f6dec76 upstream.
The function qcom_iommu_device_probe() does not perform sufficient
error checking after executing devm_ioremap_resource(), which can
result in crashes if a critical error path is encountered.
Fixes: 0ae349a0f33f ("iommu/qcom: Add qcom_iommu")
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200418134703.1760-1-tangbin@cmss.chinamobile.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cbf3264bc715e9eb384e2b68601f8c02bb9a61d upstream.
Use follow_pfn() to get the PFN of a PFNMAP VMA instead of assuming that
vma->vm_pgoff holds the base PFN of the VMA. This fixes a bug where
attempting to do VFIO_IOMMU_MAP_DMA on an arbitrary PFNMAP'd region of
memory calculates garbage for the PFN.
Hilariously, this only got detected because the first "PFN" calculated
by vaddr_get_pfn() is PFN 0 (vma->vm_pgoff==0), and iommu_iova_to_phys()
uses PA==0 as an error, which triggers a WARN in vfio_unmap_unpin()
because the translation "failed". PFN 0 is now unconditionally reserved
on x86 in order to mitigate L1TF, which causes is_invalid_reserved_pfn()
to return true and in turns results in vaddr_get_pfn() returning success
for PFN 0. Eventually the bogus calculation runs into PFNs that aren't
reserved and leads to failure in vfio_pin_map_dma(). The subsequent
call to vfio_remove_dma() attempts to unmap PFN 0 and WARNs.
WARNING: CPU: 8 PID: 5130 at drivers/vfio/vfio_iommu_type1.c:750 vfio_unmap_unpin+0x2e1/0x310 [vfio_iommu_type1]
Modules linked in: vfio_pci vfio_virqfd vfio_iommu_type1 vfio ...
CPU: 8 PID: 5130 Comm: sgx Tainted: G W 5.6.0-rc5-705d787c7fee-vfio+ #3
Hardware name: Intel Corporation Mehlow UP Server Platform/Moss Beach Server, BIOS CNLSE2R1.D00.X119.B49.1803010910 03/01/2018
RIP: 0010:vfio_unmap_unpin+0x2e1/0x310 [vfio_iommu_type1]
Code: <0f> 0b 49 81 c5 00 10 00 00 e9 c5 fe ff ff bb 00 10 00 00 e9 3d fe
RSP: 0018:ffffbeb5039ebda8 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff9a55cbf8d480 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffff9a52b771c200
RBP: 0000000000000000 R08: 0000000000000040 R09: 00000000fffffff2
R10: 0000000000000001 R11: ffff9a51fa896000 R12: 0000000184010000
R13: 0000000184000000 R14: 0000000000010000 R15: ffff9a55cb66ea08
FS: 00007f15d3830b40(0000) GS:ffff9a55d5600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000561cf39429e0 CR3: 000000084f75f005 CR4: 00000000003626e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
vfio_remove_dma+0x17/0x70 [vfio_iommu_type1]
vfio_iommu_type1_ioctl+0x9e3/0xa7b [vfio_iommu_type1]
ksys_ioctl+0x92/0xb0
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x4c/0x180
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7f15d04c75d7
Code: <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 81 48 2d 00 f7 d8 64 89 01 48
Fixes: 73fa0d10d077 ("vfio: Type1 IOMMU implementation")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0abc761bbb9418876cc4d1ebc473e4ea6352e42 upstream.
The call to ->lookup_put() was too early and it caused an unlock of the
read/write protection of the uobject after the FD was put. This allows a
race:
CPU1 CPU2
rdma_lookup_put_uobject()
lookup_put_fd_uobject()
fput()
fput()
uverbs_uobject_fd_release()
WARN_ON(uverbs_try_lock_object(uobj,
UVERBS_LOOKUP_WRITE));
atomic_dec(usecnt)
Fix the code by changing the order, first unlock and call to
->lookup_put() after that.
Fixes: 3832125624b7 ("IB/core: Add support for idr types")
Link: https://lore.kernel.org/r/20200423060122.6182-1-leon@kernel.org
Suggested-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c08cfb2d8d78bfe81b37cc6ba84f0875bddd0d5c upstream.
Initialize ib_spec on the stack before using it, otherwise we will have
garbage values that will break creating default rules with invalid parsing
error.
Fixes: a37a1a428431 ("IB/mlx4: Add mechanism to support flow steering over IB links")
Link: https://lore.kernel.org/r/20200413132235.930642-1-leon@kernel.org
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d7e3ff7b6f2c614eb21d0dc348957a47eaffb57 upstream.
GRH fields such as sgid_index, hop limit, et. are set in the QP context
when QP is created/modified.
Currently, when query QP is performed, we fill the GRH fields only if the
GRH bit is set in the QP context, but this bit is not set for RoCE. Adjust
the check so we will set all relevant data for the RoCE too.
Since this data is returned to userspace, the below is an ABI regression.
Fixes: d8966fcd4c25 ("IB/core: Use rdma_ah_attr accessor functions")
Link: https://lore.kernel.org/r/20200413132028.930109-1-leon@kernel.org
Signed-off-by: Aharon Landau <aharonl@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a263892d7d0b4fe351363f8d1a14c6a75955475 upstream.
qlt_free_session_done() tries to post async PRLO / LOGO, and waits for the
completion of these async commands. If UNLOADING is set, this is doomed to
timeout, because the async logout command will never complete.
The only way to avoid waiting pointlessly is to fail posting these commands
in the first place if the driver is in UNLOADING state. In general,
posting any command should be avoided when the driver is UNLOADING.
With this patch, "rmmod qla2xxx" completes without noticeable delay.
Link: https://lore.kernel.org/r/20200421204621.19228-3-mwilck@suse.com
Fixes: 45235022da99 ("scsi: qla2xxx: Fix driver unload by shutting down chip")
Acked-by: Arun Easi <aeasi@marvell.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
