IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 5dd8304981ecffa77bb72b1c57c4be5dfe6cfae9 ]
In the public interface for chipselect, there is always an entry
commented as "Dummy generic FIFO entry" pushed down to the fifo right
after the activate/deactivate command. The dummy entry is 0x0,
irregardless if the intention was to activate or deactive the cs. This
causes the cs line to glitch rather than beeing activated in the case
when there was an activate command.
This has been observed on oscilloscope, and have caused problems for at
least one specific flash device type connected to the qspi port. After
the change the glitch is gone and cs goes active when intended.
The reason why this worked before (except for the glitch) was because
when sending the actual data, the CS bits are once again set. Since
most flashes uses mode 0, there is always a half clk period anyway for
cs to clk active setup time. If someone would rely on timing from a
chip_select call to a transfer_one, it would fail though.
It is unknown why the dummy entry was there in the first place, git log
seems to be of no help in this case. The reference manual gives no
indication of the necessity of this. In fact the lower 8 bits are a
setup (or hold in case of deactivate) time expressed in cycles. So this
should not be needed to fulfill any setup/hold timings.
Signed-off-by: Thommy Jakobsson <thommyj@gmail.com>
Reviewed-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Link: https://lore.kernel.org/r/20200224162643.29102-1-thommyj@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27f13774654ea6bd0b6fc9b97cce8d19e5735661 ]
'dma-ranges' in a PCI bridge node does correctly set dma masks for PCI
devices not described in the DT. Certain DRA7 platforms (e.g., DRA76)
has RAM above 32-bit boundary (accessible with LPAE config) though the
PCIe bridge will be able to access only 32-bits. Add 'dma-ranges'
property in PCIe RC DT nodes to indicate the host bridge can access
only 32 bits.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb0cc635c7a9fa8a3a0f75d4d896721819c63add ]
Selecting CONFIG_DEBUG_INFO_BTF results in the below warning from ld:
ld: warning: orphan section `.BTF' from `.btf.vmlinux.bin.o' being placed in section `.BTF'
Include .BTF section in vmlinux explicitly to fix the same.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200220113132.857132-1-naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 136b5cd2e2f97581ae560cff0db2a3b5369112da ]
spi_qup_suspend() will cause synchronous external abort when
runtime suspend is enabled and applied, as it tries to
access SPI controller register while clock is already disabled
in spi_qup_pm_suspend_runtime().
Signed-off-by: Yuji sasaki <sasakiy@chromium.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200214074340.2286170-1-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3e72dfdf8227b052393f71d820ec7599909dddc2 upstream.
Similarly to commit c543cb4a5f07 ("ipv4: ensure rcu_read_lock() in
ipv4_link_failure()"), __ip_options_compile() must be called under rcu
protection.
Fixes: 3da1ed7ac398 ("net: avoid use IPCB in cipso_v4_error")
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd4d9c7d0c71866ec0c2825189ebd2ce35bd95b8 upstream.
When kmem_cache_alloc_bulk() attempts to allocate N objects from a percpu
freelist of length M, and N > M > 0, it will first remove the M elements
from the percpu freelist, then call ___slab_alloc() to allocate the next
element and repopulate the percpu freelist. ___slab_alloc() can re-enable
IRQs via allocate_slab(), so the TID must be bumped before ___slab_alloc()
to properly commit the freelist head change.
Fix it by unconditionally bumping c->tid when entering the slowpath.
Cc: stable@vger.kernel.org
Fixes: ebe909e0fdb3 ("slub: improve bulk alloc strategy")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45939ce292b4b11159719faaf60aba7d58d5fe33 upstream.
It is possible for a system with an ARMv8 timer to run a 32-bit kernel.
When this happens we will unconditionally have the vDSO code remove the
__vdso_gettimeofday and __vdso_clock_gettime symbols because
cntvct_functional() returns false since it does not match that
compatibility string.
Fixes: ecf99a439105 ("ARM: 8331/1: VDSO initialization, mapping, and synchronization")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fda31c50292a5062332fa0343c084bd9f46604d9 ]
When queueing a signal, we increment both the users count of pending
signals (for RLIMIT_SIGPENDING tracking) and we increment the refcount
of the user struct itself (because we keep a reference to the user in
the signal structure in order to correctly account for it when freeing).
That turns out to be fairly expensive, because both of them are atomic
updates, and particularly under extreme signal handling pressure on big
machines, you can get a lot of cache contention on the user struct.
That can then cause horrid cacheline ping-pong when you do these
multiple accesses.
So change the reference counting to only pin the user for the _first_
pending signal, and to unpin it when the last pending signal is
dequeued. That means that when a user sees a lot of concurrent signal
queuing - which is the only situation when this matters - the only
atomic access needed is generally the 'sigpending' count update.
This was noticed because of a particularly odd timing artifact on a
dual-socket 96C/192T Cascade Lake platform: when you get into bad
contention, on that machine for some reason seems to be much worse when
the contention happens in the upper 32-byte half of the cacheline.
As a result, the kernel test robot will-it-scale 'signal1' benchmark had
an odd performance regression simply due to random alignment of the
'struct user_struct' (and pointed to a completely unrelated and
apparently nonsensical commit for the regression).
Avoiding the double increments (and decrements on the dequeueing side,
of course) makes for much less contention and hugely improved
performance on that will-it-scale microbenchmark.
Quoting Feng Tang:
"It makes a big difference, that the performance score is tripled! bump
from original 17000 to 54000. Also the gap between 5.0-rc6 and
5.0-rc6+Jiri's patch is reduced to around 2%"
[ The "2% gap" is the odd cacheline placement difference on that
platform: under the extreme contention case, the effect of which half
of the cacheline was hot was 5%, so with the reduced contention the
odd timing artifact is reduced too ]
It does help in the non-contended case too, but is not nearly as
noticeable.
Reported-and-tested-by: Feng Tang <feng.tang@intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Huang, Ying <ying.huang@intel.com>
Cc: Philip Li <philip.li@intel.com>
Cc: Andi Kleen <andi.kleen@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 253216ffb2a002a682c6f68bd3adff5b98b71de8 ]
local->sta_mtx is held in __ieee80211_check_fast_rx_iface().
No need to use list_for_each_entry_rcu() as it also requires
a cond argument to avoid false lockdep warnings when not used in
RCU read-side section (with CONFIG_PROVE_RCU_LIST).
Therefore use list_for_each_entry();
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Link: https://lore.kernel.org/r/20200223143302.15390-1-madhuparnabhowmik10@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44343418d0f2f623cb9da6f5000df793131cbe3b ]
The KS8851 requires that packet RX and TX are mutually exclusive.
Currently, the driver hopes to achieve this by disabling interrupt
from the card by writing the card registers and by disabling the
interrupt on the interrupt controller. This however is racy on SMP.
Replace this approach by expanding the spinlock used around the
ks_start_xmit() TX path to ks_irq() RX path to assure true mutual
exclusion and remove the interrupt enabling/disabling, which is
now not needed anymore. Furthermore, disable interrupts also in
ks_net_stop(), which was missing before.
Note that a massive improvement here would be to re-use the KS8851
driver approach, which is to move the TX path into a worker thread,
interrupt handling to threaded interrupt, and synchronize everything
with mutexes, but that would be a much bigger rework, for a separate
patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7ee7d44b57c9ae174088e53a668852b7f4f452d ]
We may end up with a NULL reg_rule after the loop in
handle_channel_custom() if the bandwidth didn't fit,
check if this is the case and bail out if so.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200221104449.3b558a50201c.I4ad3725c4dacaefd2d18d3cc65ba6d18acd5dbfe@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be0aba826c4a6ba5929def1962a90d6127871969 ]
The Surfbook E11B uses the SIPODEV SP1064 touchpad, which does not supply
descriptors, so it has to be added to the override list.
BugLink: https://bugs.launchpad.net/bugs/1858299
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e433be929e63265b7412478eb7ff271467aee2d7 ]
Magic Keyboards with more recent firmware (0x0100) report Fn key differently.
Without this patch, Fn key may not behave as expected and may not be
configurable via hid_apple fnmode module parameter.
Signed-off-by: Mansour Behabadi <mansour@oxplot.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f9e12e0df012c4a9a7fd7eb0d3ae69b459d6b2c ]
In case the WDAT interface is broken, give the user an option to
ignore it to let a native driver bind to the watchdog device instead.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f967140dfb7442e2db0868b03b961f9c59418a1b ]
Enable the sampling check in kernel/events/core.c::perf_event_open(),
which returns the more appropriate -EOPNOTSUPP.
BEFORE:
$ sudo perf record -a -e instructions,l3_request_g1.caching_l3_cache_accesses true
Error:
The sys_perf_event_open() syscall returned with 22 (Invalid argument) for event (l3_request_g1.caching_l3_cache_accesses).
/bin/dmesg | grep -i perf may provide additional information.
With nothing relevant in dmesg.
AFTER:
$ sudo perf record -a -e instructions,l3_request_g1.caching_l3_cache_accesses true
Error:
l3_request_g1.caching_l3_cache_accesses: PMU Hardware doesn't support sampling/overflow-interrupts. Try 'perf stat'
Fixes: c43ca5091a37 ("perf/x86/amd: Add support for AMD NB and L2I "uncore" counters")
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20200311191323.13124-1-kim.phillips@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f4156f9656feac21f4de712fac94fae964c5d402 upstream.
The announcement messages of batman-adv COMPAT_VERSION 15 have the
possibility to announce additional information via a dynamic TVLV part.
This part is optional for the ELP packets and currently not parsed by the
Linux implementation. Still out-of-tree versions are using it to transport
things like neighbor hashes to optimize the rebroadcast behavior.
Since the ELP broadcast packets are smaller than the minimal ethernet
packet, it often has to be padded. This is often done (as specified in
RFC894) with octets of zero and thus work perfectly fine with the TVLV
part (making it a zero length and thus empty). But not all ethernet
compatible hardware seems to follow this advice. To avoid ambiguous
situations when parsing the TVLV header, just force the 4 bytes (TVLV
length + padding) after the required ELP header to zero.
Fixes: d6f94d91f766 ("batman-adv: ELP - adding basic infrastructure")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88d0895d0ea9d4431507d576c963f2ff9918144d upstream.
The probe ELPs for WiFi interfaces are expanded to contain at least
BATADV_ELP_MIN_PROBE_SIZE bytes. This is usually a lot more than the
number of bytes which the template ELP packet requires.
These extra padding bytes were not initialized and thus could contain data
which were previously stored at the same location. It is therefore required
to set it to some predefined or random values to avoid leaking private
information from the system transmitting these kind of packets.
Fixes: e4623c913508 ("batman-adv: Avoid probe ELP information leak")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc44b78157f621ff2a2618fe287a827bcb094ac4 upstream.
batadv_check_unicast_ttvn() calls skb_cow(), so pointers into the SKB data
must be (re)set after calling it. The ethhdr variable is dropped
altogether.
Fixes: 78fc6bbe0aca ("batman-adv: add UNICAST_4ADDR packet type")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A transmission scheduling for an interface which is currently dropped by
batadv_iv_ogm_iface_disable could still be in progress. The B.A.T.M.A.N. V
is simply cancelling the workqueue item in an synchronous way but this is
not possible with B.A.T.M.A.N. IV because the OGM submissions are
intertwined.
Instead it has to stop submitting the OGM when it detect that the buffer
pointer is set to NULL.
Reported-by: syzbot+a98f2016f40b9cd3818a@syzkaller.appspotmail.com
Reported-by: syzbot+ac36b6a33c28a491e929@syzkaller.appspotmail.com
Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: Hillf Danton <hdanton@sina.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40e220b4218bb3d278e5e8cc04ccdfd1c7ff8307 upstream.
Each slave interface of an B.A.T.M.A.N. IV virtual interface has an OGM
packet buffer which is initialized using data from netdevice notifier and
other rtnetlink related hooks. It is sent regularly via various slave
interfaces of the batadv virtual interface and in this process also
modified (realloced) to integrate additional state information via TVLV
containers.
It must be avoided that the worker item is executed without a common lock
with the netdevice notifier/rtnetlink helpers. Otherwise it can either
happen that half modified/freed data is sent out or functions modifying the
OGM buffer try to access already freed memory regions.
Reported-by: syzbot+0cc629f19ccb8534935b@syzkaller.appspotmail.com
Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8d23cbbf6c9f515ed678204ad2962be7c336344 upstream.
A B.A.T.M.A.N. V virtual interface has an OGM2 packet buffer which is
initialized using data from the netdevice notifier and other rtnetlink
related hooks. It is sent regularly via various slave interfaces of the
batadv virtual interface and in this process also modified (realloced) to
integrate additional state information via TVLV containers.
It must be avoided that the worker item is executed without a common lock
with the netdevice notifier/rtnetlink helpers. Otherwise it can either
happen that half modified data is sent out or the functions modifying the
OGM2 buffer try to access already freed memory regions.
Fixes: 0da0035942d4 ("batman-adv: OGMv2 - add basic infrastructure")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e6b5648bbc4cd48fab62cecbb81e9cc3c6e7e88 upstream.
The state of slave interfaces are handled differently depending on whether
the interface is up or not. All active interfaces (IFF_UP) will transmit
OGMs. But for B.A.T.M.A.N. IV, also non-active interfaces are scheduling
(low TTL) OGMs on active interfaces. The code which setups and schedules
the OGMs must therefore already be called when the interfaces gets added as
slave interface and the transmit function must then check whether it has to
send out the OGM or not on the specific slave interface.
But the commit f0d97253fb5f ("batman-adv: remove ogm_emit and ogm_schedule
API calls") moved the setup code from the enable function to the activate
function. The latter is called either when the added slave was already up
when batadv_hardif_enable_interface processed the new interface or when a
NETDEV_UP event was received for this slave interfac. As result, each
NETDEV_UP would schedule a new OGM worker for the interface and thus OGMs
would be send a lot more than expected.
Fixes: f0d97253fb5f ("batman-adv: remove ogm_emit and ogm_schedule API calls")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Tested-by: Linus Lüssing <linus.luessing@c0d3.blue>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dff9bc42ab0b2d38c5e90ddd79b238fed5b4c7ad upstream.
The function batadv_gw_node_add is responsible for adding new gw_node to
the gateway_list. It is expecting that the caller already checked that
there is not already an entry with the same key or not.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a44ebeff6bbd6ef50db41b4195fca87b21aefd20 upstream.
When a (broken) node wrongly sends multicast TT entries with a ROAM
flag then this causes any receiving node to drop all entries for the
same multicast MAC address announced by other nodes, leading to
packet loss.
Fix this DoS vector by only storing TT sync flags. For multicast TT
non-sync'ing flag bits like ROAM are unused so far anyway.
Fixes: 1d8ab8d3c176 ("batman-adv: Modified forwarding behaviour for multicast packets")
Reported-by: Leonardo Mörlein <me@irrelefant.net>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a519b83da16927fb98fd32b0f598e639d1f1859 upstream.
Since commit 54e22f265e87 ("batman-adv: fix TT sync flag inconsistencies")
TT sync flags and TT non-sync'd flags are supposed to be stored
separately.
The previous patch missed to apply this separation on a TT entry with
only a single TT orig entry.
This is a minor fix because with only a single TT orig entry the DDoS
issue the former patch solves does not apply.
Fixes: 54e22f265e87 ("batman-adv: fix TT sync flag inconsistencies")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6da7be7d24b2921f8215473ba7552796dff05fe1 upstream.
batman-adv is creating special debugfs directories in the init
net_namespace for each created soft-interface (batadv net_device). But it
is possible to rename a net_device to a completely different name then the
original one.
It can therefore happen that a user registers a new batadv net_device with
the name "bat0". batman-adv is then also adding a new directory under
$debugfs/batman-adv/ with the name "wlan0".
The user then decides to rename this device to "bat1" and registers a
different batadv device with the name "bat0". batman-adv will then try to
create a directory with the name "bat0" under $debugfs/batman-adv/ again.
But there already exists one with this name under this path and thus this
fails. batman-adv will detect a problem and rollback the registering of
this device.
batman-adv must therefore take care of renaming the debugfs directories for
soft-interfaces whenever it detects such a net_device rename.
Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36dc621ceca1be3ec885aeade5fdafbbcc452a6d upstream.
batman-adv is creating special debugfs directories in the init
net_namespace for each valid hard-interface (net_device). But it is
possible to rename a net_device to a completely different name then the
original one.
It can therefore happen that a user registers a new net_device which gets
the name "wlan0" assigned by default. batman-adv is also adding a new
directory under $debugfs/batman-adv/ with the name "wlan0".
The user then decides to rename this device to "wl_pri" and registers a
different device. The kernel may now decide to use the name "wlan0" again
for this new device. batman-adv will detect it as a valid net_device and
tries to create a directory with the name "wlan0" under
$debugfs/batman-adv/. But there already exists one with this name under
this path and thus this fails. batman-adv will detect a problem and
rollback the registering of this device.
batman-adv must therefore take care of renaming the debugfs directories
for hard-interfaces whenever it detects such a net_device rename.
Fixes: 5bc7c1eb44f2 ("batman-adv: add debugfs structure for information per interface")
Reported-by: John Soros <sorosj@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16116dac23396e73c01eeee97b102e4833a4b205 upstream.
A translation table TVLV changset sent with an OGM consists
of a number of headers (one per VLAN) plus the changeset
itself (addition and/or deletion of entries).
The per-VLAN headers are used by OGM recipients for consistency
checks. Said consistency check might determine that a full
translation table request is needed to restore consistency. If
the TT sender adds per-VLAN headers of empty VLANs into the OGM,
recipients are led to believe to have reached an inconsistent
state and thus request a full table update. The full table does
not contain empty VLANs (due to missing entries) the cycle
restarts when the next OGM is issued.
Consequently, when the translation table TVLV headers are
composed, empty VLANs are to be excluded.
Fixes: 21a57f6e7a3b ("batman-adv: make the TT CRC logic VLAN specific")
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7072337e52b3e9d5460500d8dc9cbc1ba2db084c upstream.
The previous TT sync fix so far only fixed TT responses issued by the
target node directly. So far, TT responses issued by intermediate nodes
still lead to the wrong flags being added, leading to CRC mismatches.
This behaviour was observed at Freifunk Hannover in a 800 nodes setup
where a considerable amount of nodes were still infected with 'WI'
TT flags even with (most) nodes having the previous TT sync fix applied.
I was able to reproduce the issue with intermediate TT responses in a
four node test setup and this patch fixes this issue by ensuring to
use the per originator instead of the summarized, OR'd ones.
Fixes: e9c00136a475 ("batman-adv: fix tt_global_entries flags update")
Reported-by: Leonardo Mörlein <me@irrelefant.net>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ba0f9bd3bdea1058c2b2676bec7905724418e40 upstream.
The functions batadv_tt_prepare_tvlv_local_data and
batadv_tt_prepare_tvlv_global_data are responsible for preparing a buffer
which can be used to store the TVLV container for TT and add the VLAN
information to it.
This will be done in three phases:
1. count the number of VLANs and their entries
2. allocate the buffer using the counters from the previous step and limits
from the caller (parameter tt_len)
3. insert the VLAN information to the buffer
The step 1 and 3 operate on a list which contains the VLANs. The access to
these lists must be protected with an appropriate lock or otherwise they
might operate on on different entries. This could for example happen when
another context is adding VLAN entries to this list.
This could lead to a buffer overflow in these functions when enough entries
were added between step 1 and 3 to the VLAN lists that the buffer room for
the entries (*tt_change) is smaller then the now required extra buffer for
new VLAN entries.
Fixes: 7ea7b4a14275 ("batman-adv: make the TT CRC logic VLAN specific")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f22e08932c2960f29b5e828e745c9f3fb7c1bb86 upstream.
batman-adv uses internal indices for each enabled and active interface.
It is currently used by the B.A.T.M.A.N. IV algorithm to identifify the
correct position in the ogm_cnt bitmaps.
The type for the number of enabled interfaces (which defines the next
interface index) was set to char. This type can be (depending on the
architecture) either signed (limiting batman-adv to 127 active slave
interfaces) or unsigned (limiting batman-adv to 255 active slave
interfaces).
This limit was not correctly checked when an interface was enabled and thus
an overflow happened. This was only catched on systems with the signed char
type when the B.A.T.M.A.N. IV code tried to resize its counter arrays with
a negative size.
The if_num interface index was only a s16 and therefore significantly
smaller than the ifindex (int) used by the code net code.
Both &batadv_hard_iface->if_num and &batadv_priv->num_ifaces must be
(unsigned) int to support the same number of slave interfaces as the net
core code. And the interface activation code must check the number of
active slave interfaces to avoid integer overflows.
Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ba7dcfe77037b67016263ea597a8b431692ecab upstream.
The originator node object orig_neigh_node is used to when accessing the
bcast_own(_sum) and real_packet_count information. The access to them has
to be protected with the spinlock in orig_neigh_node.
But the function uses the lock in orig_node instead. This is incorrect
because they could be two different originator node objects.
Fixes: 0ede9f41b217 ("batman-adv: protect bit operations to count OGMs with spinlock")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 198a62ddffa4a4ffaeb741f642b7b52f2d91ae9b upstream.
The batadv_v_gw_is_eligible function already assumes that orig_node is not
NULL. But batadv_gw_node_get may have failed to find the originator. It
must therefore be checked whether the batadv_gw_node_get failed and not
whether orig_node is NULL to detect this error.
Fixes: 50164d8f500f ("batman-adv: B.A.T.M.A.N. V - implement GW selection logic")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe77d8257c4d838c5976557ddb87bd789f312412 upstream.
The batman-adv unuicast fragment header contains 3 bits for the priority of
the packet. These bits will be initialized when the skb->priority contains
a value between 256 and 263. But otherwise, the uninitialized bits from the
stack will be used.
Fixes: c0f25c802b33 ("batman-adv: Include frame priority in fragment header")
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a4bc44b012cbc29c9d824be2c7ab9eac8ee6b6f upstream.
The neighbor compare API implementation for B.A.T.M.A.N. V checks whether
the neigh_ifinfo for this neighbor on a specific interface exists. A
warning is printed when it isn't found.
But it is not called inside a lock which would prevent that this
information is lost right before batadv_neigh_ifinfo_get. It must therefore
be expected that batadv_v_neigh_(cmp|is_sob) might not be able to get the
requested neigh_ifinfo.
A WARN_ON for such a situation seems not to be appropriate because this
will only flood the kernel logs. The warnings must therefore be removed.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54e22f265e872ae140755b3318521d400a094605 upstream.
This patch fixes an issue in the translation table code potentially
leading to a TT Request + Response storm. The issue may occur for nodes
involving BLA and an inconsistent configuration of the batman-adv AP
isolation feature. However, since the new multicast optimizations, a
single, malformed packet may lead to a mesh-wide, persistent
Denial-of-Service, too.
The issue occurs because nodes are currently OR-ing the TT sync flags of
all originators announcing a specific MAC address via the
translation table. When an intermediate node now receives a TT Request
and wants to answer this on behalf of the destination node, then this
intermediate node now responds with an altered flag field and broken
CRC. The next OGM of the real destination will lead to a CRC mismatch
and triggering a TT Request and Response again.
Furthermore, the OR-ing is currently never undone as long as at least
one originator announcing the according MAC address remains, leading to
the potential persistency of this issue.
This patch fixes this issue by storing the flags used in the CRC
calculation on a a per TT orig entry basis to be able to respond with
the correct, original flags in an intermediate TT Response for one
thing. And to be able to correctly unset sync flags once all nodes
announcing a sync flag vanish for another.
Fixes: e9c00136a475 ("batman-adv: fix tt_global_entries flags update")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Acked-by: Antonio Quartulli <a@unstable.cc>
[sw: typo in commit message]
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d62890885efbc48acea46964ea3af69b61c8c5eb upstream.
The wifi driver can decide to not provide parts of the station info. For
example, the expected throughput of the station can be omitted when the
used rate control doesn't provide this kind of information.
The B.A.T.M.A.N. V implementation must therefore check the filled bitfield
before it tries to access the expected_throughput of the returned
station_info.
Reported-by: Alvaro Antelo <alvaro.antelo@gmail.com>
Fixes: c833484e5f38 ("batman-adv: ELP - compute the metric based on the estimated throughput")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f3f87325dcb3c201076c81490f4da91ad4c09fc upstream.
A wifi interface should never be handled like an ethernet devices. The
parser of the cfg80211 output must therefore skip the ethtool code when
cfg80211_get_station returned an error.
Fixes: f44a3ae9a281 ("batman-adv: refactor wifi interface detection")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36d4d68cd658d914ef73ac845705c4a89e7d9e2f upstream.
The stats are generated by batadv_interface_stats and must not be stored
directly in the net_device stats member variable. The batadv_priv
bat_counters information is assembled when ndo_get_stats is called. The
stats previously stored in net_device::stats is then overwritten.
The batman-adv counters must therefore be increased when an ARP packet is
answered locally via the distributed arp table.
Fixes: c384ea3ec930 ("batman-adv: Distributed ARP Table - add snooping functions for ARP messages")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a9070ec91b37234fe915849b767c61584c64a44 upstream.
The gateway selection class variable is shared between different algorithm
versions. But the interpretation of the content is algorithm specific. The
initialization is therefore also algorithm specific.
But this was implemented incorrectly and the initialization for BATMAN_V
always overwrote the value previously written for BATMAN_IV. This could
only be avoided when BATMAN_V was disabled during compile time.
Using a special batadv_algo hook for this initialization avoids this
problem.
Fixes: 50164d8f500f ("batman-adv: B.A.T.M.A.N. V - implement GW selection logic")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51c6b429c0c95e67edd1cb0b548c5cf6a6604763 upstream.
Trying to split and transmit a unicast packet in 16 parts will fail for
the final fragment: After having sent the 15th one with a frag_packet.no
index of 14, we will increase the the index to 15 - and return with an
error code immediately, even though one more fragment is due for
transmission and allowed.
Fixing this issue by moving the check before incrementing the index.
While at it, adding an unlikely(), because the check is actually more of
an assertion.
Fixes: ee75ed88879a ("batman-adv: Fragment and send skbs larger than mtu")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 248e23b50e2da0753f3b5faa068939cbe9f8a75a upstream.
The function batadv_frag_skb_buffer was supposed not to consume the skbuff
on errors. This was followed in the helper function
batadv_frag_insert_packet when the skb would potentially be inserted in the
fragment queue. But it could happen that the next helper function
batadv_frag_merge_packets would try to merge the fragments and fail. This
results in a kfree_skb of all the enqueued fragments (including the just
inserted one). batadv_recv_frag_packet would detect the error in
batadv_frag_skb_buffer and try to free the skb again.
The behavior of batadv_frag_skb_buffer (and its helper
batadv_frag_insert_packet) must therefore be changed to always consume the
skbuff to have a common behavior and avoid the double kfree_skb.
Fixes: 610bfc6bc99b ("batman-adv: Receive fragmented packets and merge")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6c066fda90d578aacdf19771a027ed484a79825 upstream.
Add a sanity check to efivar_store_raw() the same way
efivar_{attr,size,data}_read() and efivar_show_raw() have it.
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200305084041.24053-3-vdronov@redhat.com
Link: https://lore.kernel.org/r/20200308080859.21568-25-ardb@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da72a379b2ec0bad3eb265787f7008bead0b040c upstream.
VMD subdevices are created with a PCI domain ID of 0x10000 or
higher.
These subdevices are also handled like all other PCI devices by
dmar_pci_bus_notifier().
However, when dmar_alloc_pci_notify_info() take records of such devices,
it will truncate the domain ID to a u16 value (in info->seg).
The device at (e.g.) 10000:00:02.0 is then treated by the DMAR code as if
it is 0000:00:02.0.
In the unlucky event that a real device also exists at 0000:00:02.0 and
also has a device-specific entry in the DMAR table,
dmar_insert_dev_scope() will crash on:
BUG_ON(i >= devices_cnt);
That's basically a sanity check that only one PCI device matches a
single DMAR entry; in this case we seem to have two matching devices.
Fix this by ignoring devices that have a domain number higher than
what can be looked up in the DMAR table.
This problem was carefully diagnosed by Jian-Hong Pan.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Fixes: 59ce0515cdaf3 ("iommu/vt-d: Update DRHD/RMRR/ATSR device scope caches when PCI hotplug happens")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0bb0c22c4db623f2e7b1a471596fbf1c22c6dc5 upstream.
When base address in RHSA structure doesn't match base address in
each DRHD structure, the base address in last DRHD is printed out.
This doesn't make sense when there are multiple DRHD units, fix it
by printing the buggy RHSA's base address.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Fixes: fd0c8894893cb ("intel-iommu: Set a more specific taint flag for invalid BIOS DMAR tables")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e58252e334dc3f3756f424a157d1b7484464c40 upstream.
mwifiex_process_tdls_action_frame() without checking
the incoming tdls infomation element's vality before use it,
this may cause multi heap buffer overflows.
Fix them by putting vality check before use it.
IE is TLV struct, but ht_cap and ht_oper aren’t TLV struct.
the origin marvell driver code is wrong:
memcpy(&sta_ptr->tdls_cap.ht_oper, pos,....
memcpy((u8 *)&sta_ptr->tdls_cap.ht_capb, pos,...
Fix the bug by changing pos(the address of IE) to
pos+2 ( the address of IE value ).
Signed-off-by: qize wang <wangqize888888888@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
