IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
By the specification the 0xF0000-0xF02FF range is only valid when the
DPCD revision is 1.4 or higher. Disable LTTPR support if this isn't so.
Trying to detect LTTPRs returned corrupted values for the above DPCD
range at least on a Skylake host with an LG 43UD79-B monitor with a DPCD
revision 1.2 connected.
v2: Add the actual version check.
v3: Fix s/DRPX/DPRX/ typo.
Fixes: 7b2a4ab8b0ef ("drm/i915: Switch to LTTPR transparent mode link training")
Cc: <stable@vger.kernel.org> # v5.11
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210317190149.4032966-1-imre.deak@intel.com
The DP PHY vswing/pre-emphasis level programming the driver does is
related to the DPTX -> first LTTPR link segment only. Accordingly it
should be only programmed when link training the first LTTPR and kept
as-is when training subsequent LTTPRs and the DPRX. For these latter
PHYs the vs/pe levels will be set in response to writing the
DP_TRAINING_LANEx_SET_PHY_REPEATERy DPCD registers (by an upstream LTTPR
TX PHY snooping this write access of its downstream LTTPR/DPRX RX PHY).
The above is also described in DP Standard v2.0 under 3.6.6.1.
While at it simplify and add the LTTPR that is link trained to the debug
message in intel_dp_set_signal_levels().
Fixes: b30edfd8d0b4 ("drm/i915: Switch to LTTPR non-transparent mode link training")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201229172201.4155327-2-imre.deak@intel.com
The DP Standard's recommendation is to use the LTTPR non-transparent
mode link training if LTTPRs are detected, so let's do this.
Besides power-saving, the advantages of this are that the maximum number
of LTTPRs can only be used in non-transparent mode (the limit is 5-8 in
transparent mode), and it provides a way to narrow down the reason for a
link training failure to a given link segment. Non-transparent mode is
probably also the mode that was tested the most by the industry.
The changes in this patchset:
- Pass the DP PHY that is currently link trained to all LT helpers, so
that these can access the correct LTTPR/DPRX DPCD registers.
- During LT take into account the LTTPR common lane rate/count and the
per LTTPR-PHY vswing/pre-emph limits.
- Switch to LTTPR non-transparent LT mode and train each link segment
according to the sequence in DP Standard v2.0 (complete CR/EQ for
each segment before continuing with the next segment).
v2:
- Switch to non-transparent mode during connector detection, which is
required before reading the per-PHY LTTPR capabilities.
- Move the DP_PHY_LTTPR() macro to drm_dp_helper.h (Ville)
- Use the new drm_dp_dpcd_read_phy_link_status() instead of adding the
same logic to intel_dp_get_link_status(). (Ville)
- Make intel_dp_lttpr_phy_caps() return a pointer to the whole array
instead of a pointer to its first element. (Ville)
- Add the intel_dp_phy_is_downstream_of_source() helper. (Ville)
- Add a code comment about the disable->enable quirk of
non-transparent mode.
- Add the intel_dp_training_pattern_set_reg() helper.
- Fix checkpatch/sparse warns.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-7-imre.deak@intel.com
By default LTTPRs should be in transparent link training mode,
nevertheless in this patch we switch to this default mode explicitly.
The DP Standard recommends this, supposedly because an LTTPR may be left
in the non-transparent mode (by BIOS, previous kernel, or after reset
due to a firmware bug). I haven't seen this happening, but let's follow
the DP Standard.
v2:
- Add a code comment about the explicit disabling of non-transparent
mode.
v3:
- Move check to prevent initing LTTPRs on eDP to init_dp_lttpr_init().
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-6-imre.deak@intel.com
An LTTPR can be trained with training pattern 4 even if the DPCD
revision is < 1.4, but drm_dp_training_pattern_mask() would change
pattern 4 to pattern 3 on those DPCD revisions.
Since intel_dp_training_pattern() makes already sure that the proper
training pattern is used, all that needs to be masked out is the
scrambling disable flag, which is or'd to the mask later based on the
training pattern.
v2:
- Use a helper instead of open-coding the masking. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-2-imre.deak@intel.com
Get rid of mode crtc->config usage, and some ad-hoc intel_dp state
usage by plumbing the crtc state all the way down to the link training
code.
Unfortunately we do have to keep some cached state in intel_dp so
that we can do the "does the link need retraining?" checks from
the short hpd handler.
v2: Add intel_crtc_state forward declaration
v3: Don't kill the PHY test code totally since it's
now in the hotplug work where we can get at the states
v4: Don't resurrect the debug scrambling disable bit (Imre)
Use intel_dp_mst_is_master_trans() (Imre)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001111053.24451-1-ville.syrjala@linux.intel.com
vswing/pre-emphasis adjustment calculation is needed in processing
of auto phy compliance request other than link training, so have
made non-static function.
No functional change.
v1: initial patch.
v2:
- used "intel_dp" prefix in function name. (Jani)
- used array notation instead pointer for link_status. (Ville)
v3: Scrapped the initial patch, modified commit description accordingly.
- made non-static function and used intel_dp prefix. (Jani, Manasi)
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316103759.12867-4-animesh.manna@intel.com
Add a new subdirectory for display code, and start off by moving
modesetting output/encoder code. Judging by the include changes, this is
a surprisingly clean operation.
v2:
- move intel_sdvo_regs.h too
- use tabs for Makefile file lists and sort them
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190613084416.6794-2-jani.nikula@intel.com
