IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Downstream Port Containment (PCIe r5.0, sec. 6.2.10) disables the link upon
an error and attempts to re-enable it when instructed by the DPC driver.
A slot which is both DPC- and hotplug-capable is currently powered off by
pciehp once DPC is triggered (due to the link change) and powered back up
on successful recovery. That's undesirable, the slot should remain powered
so the hotplugged device remains bound to its driver. DPC notifies the
driver of the error and of successful recovery in pcie_do_recovery() and
the driver may then restore the device to working state.
Moreover, Sinan points out that turning off slot power by pciehp may foil
recovery by DPC: Power off/on is a cold reset concurrently to DPC's warm
reset. Sathyanarayanan reports extended delays or failure in link
retraining by DPC if pciehp brings down the slot.
Fix by detecting whether a Link Down event is caused by DPC and awaiting
recovery if so. On successful recovery, ignore both the Link Down and the
subsequent Link Up event.
Afterwards, check whether the link is down to detect surprise-removal or
another DPC event immediately after DPC recovery. Ensure that the
corresponding DLLSC event is not ignored by synthesizing it and invoking
irq_wake_thread() to trigger a re-run of pciehp_ist().
The IRQ threads of the hotplug and DPC drivers, pciehp_ist() and
dpc_handler(), race against each other. If pciehp is faster than DPC, it
will wait until DPC recovery completes.
Recovery consists of two steps: The first step (waiting for link
disablement) is recognizable by pciehp through a set DPC Trigger Status
bit. The second step (waiting for link retraining) is recognizable through
a newly introduced PCI_DPC_RECOVERING flag.
If DPC is faster than pciehp, neither of the two flags will be set and
pciehp may glean the recovery status from the new PCI_DPC_RECOVERED flag.
The flag is zero if DPC didn't occur at all, hence DLLSC events are not
ignored by default.
pciehp waits up to 4 seconds before assuming that DPC recovery failed and
bringing down the slot. This timeout is not taken from the spec (it
doesn't mandate one) but based on a report from Yicong Yang that DPC may
take a bit more than 3 seconds on HiSilicon's Kunpeng platform.
The timeout is necessary because the DPC Trigger Status bit may never
clear: On Root Ports which support RP Extensions for DPC, the DPC driver
polls the DPC RP Busy bit for up to 1 second before giving up on DPC
recovery. Without the timeout, pciehp would then wait indefinitely for DPC
to complete.
This commit draws inspiration from previous attempts to synchronize DPC
with pciehp:
By Sinan Kaya, August 2018:
https://lore.kernel.org/linux-pci/20180818065126.77912-1-okaya@kernel.org/
By Ethan Zhao, October 2020:
https://lore.kernel.org/linux-pci/20201007113158.48933-1-haifeng.zhao@intel.com/
By Kuppuswamy Sathyanarayanan, March 2021:
https://lore.kernel.org/linux-pci/59cb30f5e5ac6d65427ceaadf1012b2ba8dbf66c.1615606143.git.sathyanarayanan.kuppuswamy@linux.intel.com/
Link: https://lore.kernel.org/r/0be565d97438fe2a6d57354b3aa4e8626952a00b.1619857124.git.lukas@wunner.de
Reported-by: Sinan Kaya <okaya@kernel.org>
Reported-by: Ethan Zhao <haifeng.zhao@intel.com>
Reported-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Tested-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Tested-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <kbusch@kernel.org>
pci_init_capabilities() is the only caller and doesn't use the return
value. So let's change the return type to void.
Link: https://lore.kernel.org/r/663ec440-8375-1459-ddb4-98ea76e75917@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "label", "index", and "acpi_index" sysfs attributes show firmware label
information about the device. If the ACPI Device Name _DSM is implemented
for the device, we have:
label Device name (optional, may be null)
acpi_index Instance number (unique under \_SB scope)
When there is no ACPI _DSM and SMBIOS provides an Onboard Devices structure
for the device, we have:
label Reference Designation, e.g., a silkscreen label
index Device Type Instance
Previously these attributes were dynamically created either by
pci_bus_add_device() or the pci_sysfs_init() initcall, but since they don't
need to be created or removed dynamically, we can use a static attribute so
the device model takes care of addition and removal automatically.
Convert "label", "index", and "acpi_index" to static attributes.
Presence of the ACPI _DSM (device_has_acpi_name()) determines whether the
ACPI information (label, acpi_index) or the SMBIOS information (label,
index) is visible.
[bhelgaas: commit log, split to separate patch, add "pci_dev_" prefix]
Suggested-by: Oliver O'Halloran <oohall@gmail.com>
Link: https://lore.kernel.org/r/20210416205856.3234481-6-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "vpd" sysfs attribute allows access to Vital Product Data (VPD).
Previously it was dynamically created either by pci_bus_add_device() or the
pci_sysfs_init() initcall, but since it doesn't need to be created or
removed dynamically, we can use a static attribute so the device model
takes care of addition and removal automatically.
Convert "vpd" to a static attribute and use the .is_bin_visible() callback
to check whether the device supports VPD.
Remove pcie_vpd_create_sysfs_dev_files(),
pcie_vpd_remove_sysfs_dev_files(), pci_create_capabilities_sysfs(), and
pci_create_capabilities_sysfs(), which are no longer needed.
[bhelgaas: This is substantially the same as the earlier patch from Heiner
Kallweit <hkallweit1@gmail.com>. I included Krzysztof's change here so all
the "convert to static attribute" changes are together.]
[bhelgaas: rename to vpd_read()/vpd_write() and pci_dev_vpd_attr_group]
Suggested-by: Oliver O'Halloran <oohall@gmail.com>
Based-on: https://lore.kernel.org/r/7703024f-8882-9eec-a122-599871728a89@gmail.com
Based-on-patch-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20210416205856.3234481-5-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A typical cloud provider SR-IOV use case is to create many VFs for use by
guest VMs. The VFs may not be assigned to a VM until a customer requests a
VM of a certain size, e.g., number of CPUs. A VF may need MSI-X vectors
proportional to the number of CPUs in the VM, but there is no standard way
to change the number of MSI-X vectors supported by a VF.
Some Mellanox ConnectX devices support dynamic assignment of MSI-X vectors
to SR-IOV VFs. This can be done by the PF driver after VFs are enabled,
and it can be done without affecting VFs that are already in use. The
hardware supports a limited pool of MSI-X vectors that can be assigned to
the PF or to individual VFs. This is device-specific behavior that
requires support in the PF driver.
Add a read-only "sriov_vf_total_msix" sysfs file for the PF and a writable
"sriov_vf_msix_count" file for each VF. Management software may use these
to learn how many MSI-X vectors are available and to dynamically assign
them to VFs before the VFs are passed through to a VM.
If the PF driver implements the ->sriov_get_vf_total_msix() callback,
"sriov_vf_total_msix" contains the total number of MSI-X vectors available
for distribution among VFs.
If no driver is bound to the VF, writing "N" to "sriov_vf_msix_count" uses
the PF driver ->sriov_set_msix_vec_count() callback to assign "N" MSI-X
vectors to the VF. When a VF driver subsequently reads the MSI-X Message
Control register, it will see the new Table Size "N".
Link: https://lore.kernel.org/linux-pci/20210314124256.70253-2-leon@kernel.org
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Compile-testing these drivers is currently broken. Enabling it causes a
couple of build failures though:
drivers/pci/controller/pci-thunder-ecam.c:119:30: error: shift count >= width of type [-Werror,-Wshift-count-overflow]
drivers/pci/controller/pci-thunder-pem.c:54:2: error: implicit declaration of function 'writeq' [-Werror,-Wimplicit-function-declaration]
drivers/pci/controller/pci-thunder-pem.c:392:8: error: implicit declaration of function 'acpi_get_rc_resources' [-Werror,-Wimplicit-function-declaration]
Fix them with the obvious one-line changes.
Link: https://lore.kernel.org/r/20210308152501.2135937-2-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Robert Richter <rric@kernel.org>
- Save/restore Precision Time Measurement Capability for suspend/resume
(David E. Box)
- Disable PTM during suspend to save power (David E. Box)
* pci/ptm:
PCI: Disable PTM during suspend to save power
PCI/PTM: Save/restore Precision Time Measurement Capability for suspend/resume
- Disable MSI for broken Pericom PCIe-USB adapter (Andy Shevchenko)
- Move MSI/MSI-X init to msi.c (Bjorn Helgaas)
- Move MSI/MSI-X flags updaters to msi.c (Bjorn Helgaas)
- Warn if we assign 64-bit MSI address to device that only supports 32-bit
MSI (Vidya Sagar)
* pci/msi:
PCI/MSI: Set device flag indicating only 32-bit MSI support
PCI/MSI: Move MSI/MSI-X flags updaters to msi.c
PCI/MSI: Move MSI/MSI-X init to msi.c
PCI: Use predefined Pericom Vendor ID
PCI: Disable MSI for Pericom PCIe-USB adapter
- Stop writing AER Capability when we don't own it (Sean V Kelley)
- Bind RCEC devices to the Port driver (Qiuxu Zhuo)
- Cache the RCEC RA Capability offset (Sean V Kelley)
- Add pci_walk_bridge() (Sean V Kelley)
- Clear AER status only when we control AER (Sean V Kelley)
- Recover from RCEC AER errors (Sean V Kelley)
- Add pcie_link_rcec() to associate RCiEPs with RCECs (Sean V Kelley)
- Recover from RCiEP AER errors (Sean V Kelley)
- Add pcie_walk_rcec() for RCEC AER handling (Sean V Kelley)
- Add pcie_walk_rcec() for RCEC PME handling (Sean V Kelley)
- Add RCEC AER error injection support (Qiuxu Zhuo)
* pci/err:
PCI/AER: Add RCEC AER error injection support
PCI/PME: Add pcie_walk_rcec() to RCEC PME handling
PCI/AER: Add pcie_walk_rcec() to RCEC AER handling
PCI/ERR: Recover from RCiEP AER errors
PCI/ERR: Add pcie_link_rcec() to associate RCiEPs
PCI/ERR: Recover from RCEC AER errors
PCI/ERR: Clear AER status only when we control AER
PCI/ERR: Add pci_walk_bridge() to pcie_do_recovery()
PCI/ERR: Avoid negated conditional for clarity
PCI/ERR: Use "bridge" for clarity in pcie_do_recovery()
PCI/ERR: Simplify by computing pci_pcie_type() once
PCI/ERR: Simplify by using pci_upstream_bridge()
PCI/ERR: Rename reset_link() to reset_subordinates()
PCI/ERR: Cache RCEC EA Capability offset in pci_init_capabilities()
PCI/ERR: Bind RCEC devices to the Root Port driver
PCI/AER: Write AER Capability only when we control it
- Decode PCIe 64 GT/s link speed (Gustavo Pimentel)
- De-duplicate Device IDs in the driver dynamic IDs list (Zhenzhong Duan)
- Return u8 from pci_find_capability() and similar (Puranjay Mohan)
- Return u16 from pci_find_ext_capability() and similar (Bjorn Helgaas)
- Include both device and resource name in config space resources
(Alexander Lobakin)
- Fix ACPI companion lookup for device 0 on the root bus (Rafael J.
Wysocki)
* pci/enumeration:
PCI/ACPI: Fix companion lookup for device 0 on the root bus
PCI: Keep both device and resource name for config space remaps
PCI: Return u16 from pci_find_ext_capability() and similar
PCI: Return u8 from pci_find_capability() and similar
PCI: Avoid duplicate IDs in driver dynamic IDs list
PCI: Move pci_match_device() ahead of new_id_store()
PCI: Decode PCIe 64 GT/s link speed
There are systems (for example, Intel based mobile platforms since Coffee
Lake) where the power drawn while suspended can be significantly reduced by
disabling Precision Time Measurement (PTM) on PCIe root ports as this
allows the port to enter a lower-power PM state and the SoC to reach a
lower-power idle state. To save this power, disable the PTM feature on root
ports during pci_prepare_to_sleep() and pci_finish_runtime_suspend(). The
feature will be returned to its previous state during restore and error
recovery.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=209361
Link: https://lore.kernel.org/r/20201207223951.19667-2-david.e.box@linux.intel.com
Reported-by: Len Brown <len.brown@intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI subsystem does not currently save and restore the configuration
space for the Precision Time Measurement (PTM) Extended Capability leading
to the possibility of the feature returning disabled on S3 resume. This
has been observed on Intel Coffee Lake desktops. Add save/restore of the
PTM control register. This saves the PTM Enable, Root Select, and Effective
Granularity bits.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20201207223951.19667-1-david.e.box@linux.intel.com
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Root Complex Event Collectors (RCEC) appear as peers to Root Ports and also
have the AER capability. In addition, actions need to be taken for
associated RCiEPs. In such cases the RCECs will need to be walked in order
to find and act upon their respective RCiEPs.
Extend the existing ability to link the RCECs with a walking function
pcie_walk_rcec(). Add RCEC support to the current AER service driver and
attach the AER service driver to the RCEC device.
Co-developed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Link: https://lore.kernel.org/r/20201121001036.8560-14-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
A Root Complex Event Collector terminates error and PME messages from
associated RCiEPs.
Use the RCEC Endpoint Association Extended Capability to identify
associated RCiEPs. Link the associated RCiEPs as the RCECs are enumerated.
Co-developed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Link: https://lore.kernel.org/r/20201121001036.8560-12-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
pci_msi_set_enable() and pci_msix_clear_and_set_ctrl() are only used from
msi.c, so move them from drivers/pci/pci.h to msi.c. No functional change
intended.
Link: https://lore.kernel.org/r/20201203185110.1583077-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Move pci_msi_setup_pci_dev(), which disables MSI and MSI-X interrupts, from
probe.c to msi.c so it's with all the other MSI code and more consistent
with other capability initialization. This means we must compile msi.c
always, even without CONFIG_PCI_MSI, so wrap the rest of msi.c in an #ifdef
and adjust the Makefile accordingly. No functional change intended.
Link: https://lore.kernel.org/r/20201203185110.1583077-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
reset_link() appears to be misnamed. The point is to reset any devices
below a given bridge, so rename it to reset_subordinates() to make it clear
that we are passing a bridge with the intent to reset the devices below it.
Link: https://lore.kernel.org/r/20201121001036.8560-5-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Extend support for Root Complex Event Collectors by decoding and caching
the RCEC Endpoint Association Extended Capabilities when enumerating. Use
that cached information for later error source reporting. See PCIe r5.0,
sec 7.9.10.
Co-developed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Link: https://lore.kernel.org/r/20201121001036.8560-4-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
PCIe r6.0, sec 7.5.3.18, defines a new 64.0 GT/s bit in the Supported Link
Speeds Vector of Link Capabilities 2.
This patch does not affect the speed of the link, which should be
negotiated automatically by the hardware; it only adds decoding when
showing the speed to the user.
Decode this new speed. Previously, reading the speed of a link operating
at this speed showed "Unknown speed" instead of "64.0 GT/s".
Link: https://lore.kernel.org/r/aaaab33fe18975e123a84aebce2adb85f44e2bbe.1605739760.git.gustavo.pimentel@synopsys.com
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Previously ASPM L1 Substates control registers (CTL1 and CTL2) weren't
saved and restored during suspend/resume leading to L1 Substates
configuration being lost post-resume.
Save the L1 Substates control registers so that the configuration is
retained post-resume.
Link: https://lore.kernel.org/r/20201024190442.871-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit 7e24bc347e.
7e24bc347e was based on PCIe r5.0, sec 5.9, which claims we need a 200 ms
delay when transitioning to or from D2. However, sec 5.3.1.3 states the
delay as 200 μs (microseconds), as does the table in PCIe r4.0, sec 5.9.1.
This looks like a typo in the r5.0 spec, so revert back to a 200 μs delay
instead of a 200 ms delay.
Fixes: 7e24bc347e ("PCI/PM: Apply D2 delay as milliseconds, not microseconds")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
476e7faefc ("PCI PM: Do not wait for buses in B2 or B3 during resume")
removed the last use of PCI_PM_BUS_WAIT. Remove the definition as well.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PCI devices support two variants of the D3 power state: D3hot (main power
present) D3cold (main power removed). Previously struct pci_dev contained:
unsigned int d3_delay; /* D3->D0 transition time in ms */
unsigned int d3cold_delay; /* D3cold->D0 transition time in ms */
"d3_delay" refers specifically to the D3hot state. Rename it to
"d3hot_delay" to avoid ambiguity and align with the ACPI "_DSM for
Specifying Device Readiness Durations" in the PCI Firmware spec r3.2,
sec 4.6.9.
There is no change to the functionality.
Link: https://lore.kernel.org/r/20200730210848.1578826-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Use pci_host_bridge.windows list directly instead of splicing in a
temporary list for cadence, mvebu, host-common (Rob Herring)
- Use pci_host_probe() instead of open-coding all the pieces for altera,
brcmstb, iproc, mobiveil, rcar, rockchip, tegra, v3, versatile, xgene,
xilinx, xilinx-nwl (Rob Herring)
- Convert to devm_platform_ioremap_resource_byname() instead of open-coding
platform_get_resource_byname() and devm_ioremap_resource() for altera,
cadence, mediatek, rockchip, tegra, xgene (Dejin Zheng)
- Convert to devm_platform_ioremap_resource() instead of open-coding
platform_get_resource() and devm_ioremap_resource() for aardvark,
brcmstb, exynos, ftpci100, versatile (Dejin Zheng)
- Remove redundant error messages from devm_pci_remap_cfg_resource()
callers (Dejin Zheng)
- Drop useless PCI_ENABLE_PROC_DOMAINS from versatile driver (Rob Herring)
- Default host bridge parent device to the platform device (Rob Herring)
- Drop unnecessary zeroing of host bridge fields (Rob Herring)
- Use pci_is_root_bus() instead of tracking root bus number separately in
aardvark, designware (imx6, keystone, designware-host), mobiveil,
xilinx-nwl, xilinx, rockchip, rcar (Rob Herring)
- Set host bridge bus number in pci_scan_root_bus_bridge() instead of each
driver for aardvark, designware-host, host-common, mediatek, rcar, tegra,
v3-semi (Rob Herring)
- Use bridge resources instead of parsing DT 'ranges' again for cadence
(Rob Herring)
- Remove private bus number and range from cadence (Rob Herring)
- Use devm_pci_alloc_host_bridge() to simplify rcar (Rob Herring)
- Use struct pci_host_bridge.windows list directly rather than a temporary
(Rob Herring)
- Reduce OF "missing non-prefetchable window" from error to warning message
(Rob Herring)
- Convert rcar-gen2 from old Arm-specific pci_common_init_dev() to new
arch-independent interfaces (Rob Herring)
- Move DT resource setup into devm_pci_alloc_host_bridge() (Rob Herring)
- Set bridge map_irq and swizzle_irq to default functions; drivers that
don't support legacy IRQs (iproc) need to undo this (Rob Herring)
* pci/host-probe-refactor:
PCI: Set bridge map_irq and swizzle_irq to default functions
PCI: Move DT resource setup into devm_pci_alloc_host_bridge()
PCI: rcar-gen2: Convert to use modern host bridge probe functions
PCI: of: Reduce missing non-prefetchable memory region to a warning
PCI: rcar: Use struct pci_host_bridge.windows list directly
PCI: rcar: Use devm_pci_alloc_host_bridge()
PCI: cadence: Remove private bus number and range storage
PCI: cadence: Use bridge resources for outbound window setup
PCI: Move setting pci_host_bridge.busnr out of host drivers
PCI: rcar: Use pci_is_root_bus() to check if bus is root bus
PCI: rockchip: Use pci_is_root_bus() to check if bus is root bus
PCI: xilinx: Use pci_is_root_bus() to check if bus is root bus
PCI: xilinx-nwl: Use pci_is_root_bus() to check if bus is root bus
PCI: mobiveil: Use pci_is_root_bus() to check if bus is root bus
PCI: designware: Use pci_is_root_bus() to check if bus is root bus
PCI: aardvark: Use pci_is_root_bus() to check if bus is root bus
PCI: Drop unnecessary zeroing of bridge fields
PCI: Set default bridge parent device
PCI: versatile: Drop flag PCI_ENABLE_PROC_DOMAINS
PCI: controller: Remove duplicate error message
PCI: controller: Convert to devm_platform_ioremap_resource()
PCI: controller: Convert to devm_platform_ioremap_resource_byname()
PCI: xilinx: Use pci_host_probe() to register host
PCI: xilinx-nwl: Use pci_host_probe() to register host
PCI: rockchip: Use pci_host_probe() to register host
PCI: rcar: Use pci_host_probe() to register host
PCI: iproc: Use pci_host_probe() to register host
PCI: altera: Use pci_host_probe() to register host
PCI: xgene: Use pci_host_probe() to register host
PCI: versatile: Use pci_host_probe() to register host
PCI: v3: Use pci_host_probe() to register host
PCI: tegra: Use pci_host_probe() to register host
PCI: mobiveil: Use pci_host_probe() to register host
PCI: brcmstb: Use pci_host_probe() to register host
PCI: host-common: Use struct pci_host_bridge.windows list directly
PCI: mvebu: Use struct pci_host_bridge.windows list directly
PCI: cadence: Use struct pci_host_bridge.windows list directly
# Conflicts:
# drivers/pci/controller/cadence/pcie-cadence-host.c
- Use pci_channel_state_t instead of enum pci_channel_state (Luc Van
Oostenryck)
- Simplify __aer_print_error() (Bjorn Helgaas)
- Log AER correctable errors as warning, not error (Matt Jolly)
- Rename pci_aer_clear_device_status() to pcie_clear_device_status() (Bjorn
Helgaas)
- Clear PCIe Device Status errors only if OS owns AER (Jonathan Cameron)
* pci/error:
PCI/ERR: Clear PCIe Device Status errors only if OS owns AER
PCI/ERR: Rename pci_aer_clear_device_status() to pcie_clear_device_status()
PCI/AER: Log correctable errors as warning, not error
PCI/AER: Simplify __aer_print_error()
PCI: Use 'pci_channel_state_t' instead of 'enum pci_channel_state'
Now that pci_parse_request_of_pci_ranges() callers just setup
pci_host_bridge.windows and dma_ranges directly and don't need the bus
range returned, we can just initialize them when allocating the
pci_host_bridge struct.
With this, pci_parse_request_of_pci_ranges() becomes a static function.
Link: https://lore.kernel.org/r/20200722022514.1283916-19-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
pci_aer_clear_device_status() clears the error bits in the PCIe Device
Status Register (PCI_EXP_DEVSTA). Every PCIe device has this register,
regardless of whether it supports AER.
Rename pci_aer_clear_device_status() to pcie_clear_device_status() to make
clear that it is PCIe-specific but not AER-specific. Move it to
drivers/pci/pci.c, again since it's not AER-specific. No functional change
intended.
Link: https://lore.kernel.org/r/20200717195619.766662-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently the ACS capability is being looked up at a number of places. Read
and store it once at enumeration so that it can be used by all later. No
functional change intended.
Link: https://lore.kernel.org/r/20200707224604.3737893-2-rajatja@google.com
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The method struct pci_error_handlers.error_detected() is defined and
documented as taking an 'enum pci_channel_state' for the second argument,
but most drivers use 'pci_channel_state_t' instead.
This 'pci_channel_state_t' is not a typedef for the enum but a typedef for
a bitwise type in order to have better/stricter typechecking.
Consolidate everything by using 'pci_channel_state_t' in the method's
definition, in the related helpers and in the drivers.
Enforce use of 'pci_channel_state_t' by replacing 'enum pci_channel_state'
with an anonymous 'enum'.
Note: Currently, from a typechecking point of view this patch changes
nothing because only the constants defined by the enum are bitwise, not the
enum itself (sparse doesn't have the notion of 'bitwise enum'). This may
change in some not too far future, hence the patch.
[bhelgaas: squash in
https://lore.kernel.org/r/20200702162651.49526-3-luc.vanoostenryck@gmail.comhttps://lore.kernel.org/r/20200702162651.49526-4-luc.vanoostenryck@gmail.com]
Link: https://lore.kernel.org/r/20200702162651.49526-2-luc.vanoostenryck@gmail.com
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The AER interfaces to clear error status registers were a confusing mess:
- pci_cleanup_aer_uncorrect_error_status() cleared non-fatal errors
from the Uncorrectable Error Status register.
- pci_aer_clear_fatal_status() cleared fatal errors from the
Uncorrectable Error Status register.
- pci_cleanup_aer_error_status_regs() cleared the Root Error Status
register (for Root Ports), the Uncorrectable Error Status register,
and the Correctable Error Status register.
Rename them to make them consistent:
From To
---------------------------------------- -------------------------------
pci_cleanup_aer_uncorrect_error_status() pci_aer_clear_nonfatal_status()
pci_aer_clear_fatal_status() pci_aer_clear_fatal_status()
pci_cleanup_aer_error_status_regs() pci_aer_clear_status()
Since pci_cleanup_aer_error_status_regs() (renamed to
pci_aer_clear_status()) is only used within drivers/pci/, move the
declaration from <linux/aer.h> to drivers/pci/pci.h.
[bhelgaas: commit log, add renames]
Link: https://lore.kernel.org/r/d1310a75dc3d28f7e8da4e99c45fbd3e60fe238e.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If firmware controls DPC, it is generally responsible for managing the DPC
capability and events, and the OS should not access the DPC capability.
However, if firmware controls DPC and both the OS and the platform support
Error Disconnect Recover (EDR) notifications, the OS EDR notify handler is
responsible for recovery, and the notify handler may read/write the DPC
capability until it clears the DPC Trigger Status bit. See [1], sec 4.5.1,
table 4-6.
Expose some DPC error handling functions so they can be used by the EDR
notify handler.
[1] Downstream Port Containment Related Enhancements ECN, Jan 28, 2019,
affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/12888
Link: https://lore.kernel.org/r/e9000bb15b3a4293e81d98bb29ead7c84a6393c9.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per the SFI _OSC and DPC Updates ECN [1] implementation note flowchart, the
OS seems to be expected to clear AER status even if it doesn't have
ownership of the AER capability. Unlike the DPC capability, where a DPC
ECN [2] specifies a window when the OS is allowed to access DPC registers
even if it doesn't have ownership, there is no clear model for AER.
Add pci_aer_raw_clear_status() to clear the AER error status registers
unconditionally. This is intended for use only by the EDR path (see [2]).
[1] System Firmware Intermediary (SFI) _OSC and DPC Updates ECN, Feb 24,
2020, affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/14076
[2] Downstream Port Containment Related Enhancements ECN, Jan 28, 2019,
affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/12888
[bhelgaas: changelog]
Link: https://lore.kernel.org/r/c19ad28f3633cce67448609e89a75635da0da07d.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
As per the DPC Enhancements ECN [1], sec 4.5.1, table 4-4, if the OS
supports Error Disconnect Recover (EDR), it must invalidate the software
state associated with child devices of the port without attempting to
access the child device hardware. In addition, if the OS supports DPC, it
must attempt to recover the child devices if the port implements the DPC
Capability. If the OS continues operation, the OS must inform the firmware
of the status of the recovery operation via the _OST method.
Return the result of pcie_do_recovery() so we can report it to firmware via
_OST.
[1] Downstream Port Containment Related Enhancements ECN, Jan 28, 2019,
affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/12888
Link: https://lore.kernel.org/r/eb60ec89448769349c6722954ffbf2de163155b5.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we passed the PCIe service type parameter to pcie_do_recovery(),
where reset_link() looked up the underlying pci_port_service_driver and its
.reset_link() function pointer. Instead of using this roundabout way, we
can just pass the driver-specific .reset_link() callback function when
calling pcie_do_recovery() function.
This allows us to call pcie_do_recovery() from code that is not a PCIe port
service driver, e.g., Error Disconnect Recover (EDR) support.
Remove pcie_port_find_service() and pcie_port_service_driver.reset_link
since they are now unused.
Link: https://lore.kernel.org/r/60e02b87b526cdf2930400059d98704bf0a147d1.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add PCIE_LNKCAP2_SLS2SPEED macro for transforming raw Link Capabilities 2
values to the pci_bus_speed. This is next to PCIE_SPEED2MBS_ENC() to make
it easier to update both places when adding support for new speeds.
Link: https://lore.kernel.org/r/1581937984-40353-10-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously some PCI speed strings came from pci_speed_string(), some came
from the PCIe-specific PCIE_SPEED2STR(), and some came from a PCIe-specific
switch statement. These methods were inconsistent:
pci_speed_string() PCIE_SPEED2STR() switch
------------------ ---------------- ------
33 MHz PCI
...
2.5 GT/s PCIe 2.5 GT/s 2.5 GT/s
5.0 GT/s PCIe 5 GT/s 5 GT/s
8.0 GT/s PCIe 8 GT/s 8 GT/s
16.0 GT/s PCIe 16 GT/s 16 GT/s
32.0 GT/s PCIe 32 GT/s 32 GT/s
Standardize on pci_speed_string() as the single source of these strings.
Note that this adds ".0" and "PCIe" to some messages, including sysfs
"max_link_speed" files, a brcmstb "link up" message, and the link status
dmesg logging, e.g.,
nvme 0000:01:00.0: 16.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x4 link at 0000:00:01.1 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
I think it's better to standardize on a single version of the speed text.
Previously we had strings like this:
/sys/bus/pci/slots/0/cur_bus_speed: 8.0 GT/s PCIe
/sys/bus/pci/slots/0/max_bus_speed: 8.0 GT/s PCIe
/sys/devices/pci0000:00/0000:00:1c.0/current_link_speed: 8 GT/s
/sys/devices/pci0000:00/0000:00:1c.0/max_link_speed: 8 GT/s
This changes the latter two to match the slots files:
/sys/devices/pci0000:00/0000:00:1c.0/current_link_speed: 8.0 GT/s PCIe
/sys/devices/pci0000:00/0000:00:1c.0/max_link_speed: 8.0 GT/s PCIe
Based-on-patch by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add pci_speed_string() to return a text description of the supplied bus or
link speed. The slot code previously used the private
pci_bus_speed_strings[] array for this purpose, but adding this interface
will enable us to consolidate similar code elsewhere.
Export pcie_link_speed[] and pci_speed_string() so they can be used by
modules.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link speed 32.0 GT/s is supported in PCIe r5.0. Add this speed to
PCIE_SPEED2STR() and PCIE_SPEED2MBS_ENC() to correctly decode it.
This is complementary to de76cda215 ("PCI: Decode PCIe 32 GT/s link
speed").
Link: https://lore.kernel.org/r/1581937984-40353-2-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The number of possible devfns is 256, but pci_add_dma_alias() allocated a
bitmap of size 255. Fix this off-by-one error.
This fixes commits 338c3149a2 ("PCI: Add support for multiple DMA
aliases") and c663579273 ("PCI: Allocate dma_alias_mask with
bitmap_zalloc()"), but I doubt it was possible to see a problem because
it takes 4 64-bit longs (or 8 32-bit longs) to hold 255 bits, and
bitmap_zalloc() doesn't save the 255-bit size anywhere.
[bhelgaas: commit log, move #define to drivers/pci/pci.h, include loop
limit fix from Qian Cai:
https://lore.kernel.org/r/20191218170004.5297-1-cai@lca.pw]
Signed-off-by: James Sewart <jamessewart@arista.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
- Consolidate DT "dma-ranges" parsing and convert all host drivers to use
shared parsing (Rob Herring)
* remotes/lorenzo/pci/mmio-dma-ranges:
PCI: Make devm_of_pci_get_host_bridge_resources() static
PCI: rcar: Use inbound resources for setup
PCI: iproc: Use inbound resources for setup
PCI: xgene: Use inbound resources for setup
PCI: v3-semi: Use inbound resources for setup
PCI: ftpci100: Use inbound resources for setup
PCI: of: Add inbound resource parsing to helpers
PCI: versatile: Enable COMPILE_TEST
PCI: versatile: Remove usage of PHYS_OFFSET
PCI: versatile: Use pci_parse_request_of_pci_ranges()
PCI: xilinx-nwl: Use pci_parse_request_of_pci_ranges()
PCI: xilinx: Use pci_parse_request_of_pci_ranges()
PCI: xgene: Use pci_parse_request_of_pci_ranges()
PCI: v3-semi: Use pci_parse_request_of_pci_ranges()
PCI: rockchip: Drop storing driver private outbound resource data
PCI: rockchip: Use pci_parse_request_of_pci_ranges()
PCI: mobiveil: Use pci_parse_request_of_pci_ranges()
PCI: mediatek: Use pci_parse_request_of_pci_ranges()
PCI: iproc: Use pci_parse_request_of_pci_ranges()
PCI: faraday: Use pci_parse_request_of_pci_ranges()
PCI: dwc: Use pci_parse_request_of_pci_ranges()
PCI: altera: Use pci_parse_request_of_pci_ranges()
PCI: aardvark: Use pci_parse_request_of_pci_ranges()
PCI: Export pci_parse_request_of_pci_ranges()
resource: Add a resource_list_first_type helper
# Conflicts:
# drivers/pci/controller/pcie-rcar.c
