IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Most AXPxxx-based reference designs place a 10k NTC thermistor on a
TS pin. When appropriately configured, AXP PMICs will inject fixed
current (80uA by default) into TS pin and measure the voltage across a
thermistor. The PMIC itself will by default compare this voltage with
predefined thresholds and disable battery charging whenever
the battery is too hot or too cold.
Alternatively, the TS pin can be configured as general-purpose
ADC input. This mode is not supported by the driver.
This patch allows reading the voltage on the TS pin. It can be then
either processed by userspace or used by kernel consumer like hwmon
ntc thermistor driver.
Signed-off-by: Evgeny Boger <boger@wirenboard.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Quentin Schulz <foss+kernel@0leil.net>
Link: https://lore.kernel.org/r/20211118141233.247907-2-boger@wirenboard.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable/disable internal i2c controller slave autoprobing at bootstrap.
Disable sensor-hub is useful if i2c controller clock/data lines are
connected through a pull-up with other chip lines (e.g. SDO/SA0).
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/54287a93922ac839501b776d288cc368aa81f0ab.1636816719.git.lorenzo@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce the capability to disable sensorhub through a device-tree
property since there are some configurations where users want to
explicitly disable sensor-hub auto-probing at bootstrap.
A typical configuration is when the sensorhub clock/data lines are connected
to a pull-up resistor since no slave sensors are connected to the i2c master.
If SDO/SA0 line is connected to the same pull-up resistor, when the driver
tries to probe slave devices connected on sensor-hub, it will force SDO/SA0
line to low, modifying the device i2c address.
Tested-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/ad7894e7b1c6fb3427fab3f623bb942860ad45cf.1636816719.git.lorenzo@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add test for newly introduced type IIO_VAL_INT_64.
Signed-off-by: Andriy Tryshnivskyy <andriy.tryshnivskyy@opensynergy.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211105100501.1904-3-andriy.tryshnivskyy@opensynergy.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add KUNIT_ASSERT_NOT_ERR_OR_NULL(test, buf) for every test.
Also use ARRAY_SIZE(values) where it is possible.
Signed-off-by: Andriy Tryshnivskyy <andriy.tryshnivskyy@opensynergy.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211105100501.1904-2-andriy.tryshnivskyy@opensynergy.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The shared parameter should be configurable based on its usage, and not
constrained to IIO_SHARED_BY_TYPE.
This patch aims to improve the flexibility in using the
IIO_ENUM_AVAILABLE define and avoid redefining custom iio enums that
expose the shared parameter.
An example is the ad5766.c driver where IIO_ENUM_AVAILABLE_SHARED was
defined in order to achieve `shared` parameter customization.
The current state of the IIO_ENUM_AVAILABLE implementation will imply
similar redefinitions each time a driver will require access to the
`shared` parameter. An example would be admv1013 driver which will
require custom device attribute for the frequency translation modes:
Quadrature I/Q mode and Intermediate Frequency mode.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211119085627.6348-1-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We know that the buffer's alignment will always be a power of two;
therefore, we can use the faster round_down() macro.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211115141925.60164-4-paul@crapouillou.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This structure was never used anywhere, so it can safely be dropped.
It will later be re-introduced as a different structure in a
different header.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211115141925.60164-3-paul@crapouillou.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use dedicated variable for index in the loop in the
iio_buffers_alloc_sysfs_and_mask(). This will make code cleaner and
less error prone as proved by previous changes done in this function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211013094923.2473-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Previously ltr501 driver supported a number of light and,
proximity sensors including ltr501, ltr559 and ltr301.
This adds support for another light sensor ltr303
used in Seeed Studio reTerminal, a carrier board
for Raspberry Pi 4 CM.
Signed-off-by: Maslov Dmitry <maslovdmitry@seeed.cc>
Link: https://lore.kernel.org/r/20211106174137.6783-1-maslovdmitry@seeed.cc
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The print function dev_err() is redundant because
platform_get_irq() already prints an error.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211105015504.39226-1-vulab@iscas.ac.cn
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When processing raw data using channel scan_type.shift as source of
trust to shift data appropriately.
When processing the temperature channel, use a 16bit big endian variable
as buffer to increase conversion readability.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20211104082413.3681212-14-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
By using scan_type.realbits when processing raw data,
we use scan_type.shit only once, thus we don't need to define a local
variable for it anymore.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20211104082413.3681212-12-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use channel definition as root of trust and replace constant
when reading elements directly using the raw sysfs attributes.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20211104082413.3681212-11-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use channel definition as root of trust and replace constant
when reading elements directly using the raw sysfs attributes.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20211104082413.3681212-10-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use channel definition as root of trust and replace constant
when reading elements directly using the raw sysfs attributes.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20211104082413.3681212-8-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use channel definition as root of trust and replace constant
when reading elements directly using the raw sysfs attributes.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20211104082413.3681212-7-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use channel definition as root of trust and replace constant
when reading elements directly using the raw sysfs attributes.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20211104082413.3681212-6-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use channel definition as root of trust and replace constant
when reading elements directly using the raw sysfs attributes.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20211104082413.3681212-5-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use channel definition as root of trust and replace constant
when reading elements directly using the raw sysfs attributes.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20211104082413.3681212-4-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use channel definition as root of trust and replace constant
when reading elements directly using the raw sysfs attributes.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20211104082413.3681212-3-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use channel definition as root of trust and replace constant
when reading elements directly using the raw sysfs attributes.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20211104082413.3681212-2-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Using `dev_get_drvdata()` in IIO sysfs callbacks to get a pointer to the
IIO device is a relic from the very early days of IIO. The IIO core as well
as most other drivers have switched over to using `dev_to_iio_dev()`
instead.
This driver is one of the last few drivers remaining that uses the outdated
idiom, update it. This will allow to eventually update the IIO core to no
longer set the drvdata for the IIO device and free it up for driver usage.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211019082929.30503-2-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The at91-sama5d2 driver calls `to_platform_device()` on a struct device
that is part of a IIO device. This is incorrect since
`to_platform_device()` must only be called on a struct device that is part
of a platform device.
The code still works by accident because non of the struct platform_device
specific fields are accessed.
Refactor the code a bit so that it behaves identically, but does not use
the incorrect cast. This avoids accidentally adding undefined behavior in
the future by assuming the `struct platform_device` is actually valid.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20211019082929.30503-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IRQ handler's return type is irqreturn_t. The mma8452 uses a variable
to store the return value, but the variable is of type int. Change this to
irqreturn_t. This makes it easier to verify that the code is correct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211101102734.32291-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core handles a trigger ops with all NULL callbacks the
same as if the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-9-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core handles a trigger ops with all NULL callbacks the
same as if the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-8-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core handles a trigger ops with all NULL callbacks the same as if
the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-7-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core handles a trigger ops with all NULL callbacks the
same as if the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-6-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core handles a trigger ops with all NULL callbacks the
same as if the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-5-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core handles a trigger ops with all NULL callbacks the
same as if the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-4-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core handles a trigger ops with all NULL callbacks the
same as if the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-3-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core handles a trigger ops with all NULL callbacks the
same as if the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-2-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core handles a trigger ops with all NULL callbacks the
same as if the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_device_type struct is never modified, mark it as const. This allows
it to be placed in a read-only memory section, which will protect against
accidental or deliberate modification.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031080421.2086-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
kthread_run() and kthread_stop() already do reference
counting of the task, so remove get_task_struct/put_task_struct()
to avoid double reference counting.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211021124254.3247-2-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Repalce kthread_create/wake_up_process() with kthread_run()
to simplify the code.
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211021124254.3247-1-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ms5611 passes &indio_dev->dev as a parameter to all its IO callbacks
only to directly cast the struct device back to struct iio_dev. And the
struct iio_dev is then only used to get the drivers state struct.
Simplify this a bit by passing the state struct directly. This makes it a
bit easier to follow what the code is doing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211020142110.7060-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The `imx7d_adc_enable()` and `imx7d_adc_disable()` functions are used as
the suspend and resume callbacks for the device. When called as
suspend/resume functions they are called with the platform_device's device
as their parameter.
In addition the functions are called on device probe and remove. In this
case they are passed the struct device of the IIO device that the driver
registers.
This works because in the `imx7d_adc_{enable,disable}()` functions the
passed struct device is only ever used as a parameter to `dev_get_drvdata()`
and `dev_get_drvdata()` returns the same value for the platform device and
the IIO device.
But for consistency we should pass the same struct device to the
`imx7d_adc_{enable,disable}()` in all cases. This will avoid accidental
breakage if the device is ever used for something more than
`dev_get_drvdata()`.
Another motivation is that `dev_get_drvdata()` on the IIO device relies on
the IIO core calling `dev_set_drvdata()`. Something we want to remove.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211020085754.16654-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Using `dev_get_drvdata()` in IIO sysfs callbacks to get a pointer to the
IIO device is a relic from the very early days of IIO. The IIO core as well
as most other drivers have switched over to using `dev_to_iio_dev()`
instead.
This driver is one of the last few drivers remaining that uses the outdated
idiom, update it. This will allow to eventually update the IIO core to no
longer set the drvdata for the IIO device and free it up for driver usage.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211020085349.16178-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix following coccicheck warning:
./drivers/iio/adc/stm32-adc.c:2014:1-33: WARNING: Function
for_each_available_child_of_node should have of_node_put() before return.
Early exits from for_each_available_child_of_node should decrement the
node reference counter. Replace return by goto here.
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20211021121826.6339-1-wanjiabing@vivo.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In some setups the IRQ signal of the XADC might not be wired to the host
system. The driver currently requires that an interrupt is specified. Make
the interrupt optional so the driver can be used in such setups where the
interrupt is not connected.
Since both the internal triggers as well as events depend on the interrupt
being connected both are not available when the interrupt is not connected.
Buffered access is still supported even without an interrupt since an
external trigger can be used.
The IRQ is only optional when using the AXI interface, since the PCAP
interface needs the IRQ for reading and writing registers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211021125950.28707-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Whan an i2c driver's remove function returns a non-zero error code
nothing happens apart from emitting a generic error message. Make this
error message more device specific and return zero instead.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211025195007.84541-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
clk_get_rate() is not guaranteed to work if called before
clk_prepare_enable().
Reorder clk_get_rate(), so it's called after clk_prepare_enable() and
after devm_add_action_or_reset() of lpc18xx_clk_disable().
Not that this is not a problem on this particular device, but it is
good to remove a case that might get copied elsewhere.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: André Gustavo Nakagomi Lopez <andregnl@usp.br>
Link: https://lore.kernel.org/r/YXag5l4xBkGQH3tq@Andryuu.br
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add Kconfig support for -Wimplicit-fallthrough for both GCC and Clang.
The compiler option is under configuration CC_IMPLICIT_FALLTHROUGH,
which is enabled by default.
Special thanks to Nathan Chancellor who fixed the Clang bug[1][2]. This
bugfix only appears in Clang 14.0.0, so older versions still contain
the bug and -Wimplicit-fallthrough won't be enabled for them, for now.
This concludes a long journey and now we are finally getting rid
of the unintentional fallthrough bug-class in the kernel, entirely. :)
Link: 9ed4a94d64 [1]
Link: https://bugs.llvm.org/show_bug.cgi?id=51094 [2]
Link: https://github.com/KSPP/linux/issues/115
Link: https://github.com/ClangBuiltLinux/linux/issues/236
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Clean up open-coded swap() calls.
* A little bit of #ifdef golf to complete the reunification of the
kernel and userspace libxfs source code.
-----BEGIN PGP SIGNATURE-----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=wsFu
-----END PGP SIGNATURE-----
Merge tag 'xfs-5.16-merge-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs cleanups from Darrick Wong:
"The most 'exciting' aspect of this branch is that the xfsprogs
maintainer and I have worked through the last of the code
discrepancies between kernel and userspace libxfs such that there are
no code differences between the two except for #includes.
IOWs, diff suffices to demonstrate that the userspace tools behave the
same as the kernel, and kernel-only bits are clearly marked in the
/kernel/ source code instead of just the userspace source.
Summary:
- Clean up open-coded swap() calls.
- A little bit of #ifdef golf to complete the reunification of the
kernel and userspace libxfs source code"
* tag 'xfs-5.16-merge-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: sync xfs_btree_split macros with userspace libxfs
xfs: #ifdef out perag code for userspace
xfs: use swap() to make dabtree code cleaner
