IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
priv->plat->mdio_bus_data is optional, some platforms may not set it,
however we proceed to look straight at priv->plat->mdio_bus_data->has_xpcs.
Since the xpcs is instantiated based on the has_xpcs property, we can
avoid looking at the priv->plat->mdio_bus_data structure altogether and
just check for the presence of the xpcs pointer.
Fixes: 11059740e616 ("net: pcs: xpcs: convert to phylink_pcs_ops")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Intel mGbE supports 2.5Gbps link speed by increasing the clock rate by
2.5 times of the original rate. In this mode, the serdes/PHY operates at a
serial baud rate of 3.125 Gbps and the PCS data path and GMII interface of
the MAC operate at 312.5 MHz instead of 125 MHz.
For Intel mGbE, the overclocking of 2.5 times clock rate to support 2.5G is
only able to be configured in the BIOS during boot time. Kernel driver has
no access to modify the clock rate for 1Gbps/2.5G mode. The way to
determined the current 1G/2.5G mode is by reading a dedicated adhoc
register through mdio bus. In short, after the system boot up, it is either
in 1G mode or 2.5G mode which not able to be changed on the fly.
Compared to 1G mode, the 2.5G mode selects the 2500BASEX as PHY interface and
disables the xpcs_an_inband. This is to cater for some PHYs that only
supports 2500BASEX PHY interface with no autonegotiation.
v2: remove MAC supported link speed masking
v3: Restructure to introduce intel_speed_mode_2500() to read serdes registers
for max speed supported and select the appropritate configuration.
Use max_speed to determine the supported link speed mask.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a preparation patch for the enabling of Intel mGbE 2.5Gbps
link speed. The Intel mGbR link speed configuration (1G/2.5G) is depends on
a mdio ADHOC register which can be configured in the bios menu.
As PHY interface might be different for 1G and 2.5G, the mdio bus need be
ready to check the link speed and select the PHY interface before probing
the xPCS.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since all the remaining members of struct mdio_xpcs_ops have direct
equivalents in struct phylink_pcs_ops, it is about time we remove it
altogether.
Since the phylink ops return void, we need to remove the error
propagation from the various xpcs methods and simply print an error
message where appropriate.
Since xpcs_get_state_c73() detects link faults and attempts to reset the
link on its own by calling xpcs_config(), but xpcs_config() now has a
lot of phylink arguments which are not needed and cannot be simply
fabricated by anybody else except phylink, the actual implementation has
been moved into a smaller xpcs_do_config().
The const struct mdio_xpcs_ops *priv->hw->xpcs has been removed, so we
need to look at the struct mdio_xpcs_args pointer now as an indication
whether the port has an XPCS or not.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unify the 2 existing PCS drivers (lynx and xpcs) by doing a similar
thing on probe, which is to have a *_create function that takes a
struct mdio_device * given by the caller, and builds a private PCS
structure around that.
This changes stmmac to hold only a pointer to the xpcs, as opposed to
the full structure. This will be used in the next patch when struct
mdio_xpcs_ops is removed. Currently a pointer to struct mdio_xpcs_ops
is used as a shorthand to determine whether the port has an XPCS or not.
We can do the same now with the mdio_xpcs_args pointer.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling a function pointer with a single implementation through
struct mdio_xpcs_ops is clunky, and the stmmac_do_callback system forces
this to return int, even though it always returns zero.
Simply remove the "validate" function pointer from struct mdio_xpcs_ops
and replace it with an exported xpcs_validate symbol which is called
directly by stmmac.
priv->hw->xpcs is of the type "const struct mdio_xpcs_ops *" and is used
as a placeholder/synonym for priv->plat->mdio_bus_data->has_xpcs. It is
done that way because the mdio_bus_data pointer might or might not be
populated in all stmmac instantiations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The operating mode of the driver is currently to populate its
struct mdio_xpcs_args::supported and struct mdio_xpcs_args::an_mode
statically in xpcs_probe(), based on the passed phy_interface_t,
and work with those.
However this is not the operation that phylink expects from a PCS
driver, because the port might be attached to an SFP cage that triggers
changes of the phy_interface_t dynamically as one SFP module is
unpluggged and another is plugged.
To migrate towards that model, the struct mdio_xpcs_args should not
cache anything related to the phy_interface_t, but just look up the
statically defined, const struct xpcs_compat structure corresponding to
the detected PCS OUI/model number.
So we delete the "supported" and "an_mode" members of struct
mdio_xpcs_args, and add the "id" structure there (since the ID is not
expected to change at runtime).
Since xpcs->supported is used deep in the code in _xpcs_config_aneg_c73(),
we need to modify some function headers to pass the xpcs_compat from all
callers. In turn, the xpcs_compat is always supplied externally to the
xpcs module:
- Most of the time by phylink
- In xpcs_probe() it is needed because xpcs_soft_reset() writes to
MDIO_MMD_PCS or to MDIO_MMD_VEND2 depending on whether an_mode is clause
37 or clause 73. In order to not introduce functional changes related
to when the soft reset is issued, we continue to require the initial
phy_interface_t argument to be passed to xpcs_probe() so we can pass
this on to xpcs_soft_reset().
- stmmac_open() wants to know whether to call stmmac_init_phy() or not,
and for that it looks inside xpcs->an_mode, because the clause 73
(backplane) AN modes supposedly do not have a PHY. Because we moved
an_mode outside of struct mdio_xpcs_args, this is now no longer
directly possible, so we introduce a helper function xpcs_get_an_mode()
which protects the data encapsulation of the xpcs module and requires
a phy_interface_t to be passed as argument. This function can look up
the appropriate compat based on the phy_interface_t.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Intel platforms, not all safety features are enabled on the hardware.
The current implementation enable all safety features by default. This
will cause mass error and warning printouts after the module is loaded.
Introduce platform specific safety features flag to enable or disable
each safety features.
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed link does not need mdio bus and in that case mdio_bus_data will
not be allocated. Before using mdio_bus_data we should check for NULL.
This patch fix the kernel panic due to NULL pointer dereference of
mdio_bus_data when it is not allocated.
Without this patch we do see following kernel crash caused due to kernel
NULL pointer dereference.
Call trace:
stmmac_dvr_probe+0x3c/0x10b0
dwc_eth_dwmac_probe+0x224/0x378
platform_probe+0x68/0xe0
really_probe+0x130/0x3d8
driver_probe_device+0x68/0xd0
device_driver_attach+0x74/0x80
__driver_attach+0x58/0xf8
bus_for_each_dev+0x7c/0xd8
driver_attach+0x24/0x30
bus_add_driver+0x148/0x1f0
driver_register+0x64/0x120
__platform_driver_register+0x28/0x38
dwc_eth_dwmac_driver_init+0x1c/0x28
do_one_initcall+0x78/0x158
kernel_init_freeable+0x1f0/0x244
kernel_init+0x14/0x118
ret_from_fork+0x10/0x30
Code: f9002bfb 9113e2d9 910e6273 aa0003f7 (f9405c78)
---[ end trace 32d9d41562ddc081 ]---
Fixes: e5e5b771f684 ("net: stmmac: make in-band AN mode parsing is supported for non-DT")
Signed-off-by: Sriranjani P <sriranjani.p@samsung.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Link: https://lore.kernel.org/r/20210528071056.35252-1-sriranjani.p@samsung.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix system hang with below sequences:
~# ifconfig ethx down
~# ifconfig ethx hw ether xx:xx:xx:xx:xx:xx
After ethx down, stmmac all clocks gated off and then register access causes
system hang.
Fixes: 5ec55823438e ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should be a mistake to fix conflicts when removing RFC tag to
repost the patch.
Fixes: 5ec55823438e ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the xdp_{init,prepare}_buff() helpers instead of
an open-coded version.
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both get and set WoL will check device_can_wakeup(), if MAC supports PMT, it
will set device wakeup capability. After commit 1d8e5b0f3f2c ("net: stmmac:
Support WOL with phy"), device wakeup capability will be overwrite in
stmmac_init_phy() according to phy's Wol feature. If phy doesn't support WoL,
then MAC will lose wakeup capability. To fix this issue, only overwrite device
wakeup capability when MAC doesn't support PMT.
For STMMAC now driver checks MAC's WoL capability if MAC supports PMT, if
not support, driver will check PHY's WoL capability.
Fixes: 1d8e5b0f3f2c ("net: stmmac: Support WOL with phy")
Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX FIFO overflows when the system is not able to process all received
packets and they start accumulating (first in the DMA queue in memory,
then in the FIFO). An interrupt is then raised for each overflowing packet
and handled in stmmac_interrupt(). This is counter-productive, since it
brings the system (or more likely, one CPU core) to its knees to process
the FIFO overflow interrupts.
stmmac_interrupt() handles overflow interrupts by writing the rx tail ptr
into the corresponding hardware register (according to the MAC spec, this
has the effect of restarting the MAC DMA). However, without freeing any rx
descriptors, the DMA stops right away, and another overflow interrupt is
raised as the FIFO overflows again. Since the DMA is already restarted at
the end of stmmac_rx_refill() after freeing descriptors, disabling FIFO
overflow interrupts and the corresponding handling code has no side effect,
and eliminates the interrupt storm when the RX FIFO overflows.
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20210506143312.20784-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
An issue found when network interface is down and up again, FPE handshake
fails to trigger. This is due to __FPE_REMOVING bit remains being set in
stmmac_fpe_stop_wq() but not cleared in stmmac_fpe_start_wq(). This
cause FPE workqueue task, stmmac_fpe_lp_task() not able to be executed.
To fix this, add clearing __FPE_REMOVING bit in stmmac_fpe_start_wq().
Fixes: 5a5586112b92 ("net: stmmac: support FPE link partner hand-shaking procedure")
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DWMAC Core 5.20 onwards supports HW descriptor prefetching.
Additionally, it also depends on platform specific RTL configuration.
This capability could be enabled by setting DMA_Mode bit-19 (DCHE).
So, to enable this cability, platform must set plat->dma_cfg->dche = true
and the DWMAC core version must be 5.20 onwards. Else, this capability
wouldn`t be configured
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TSO and TBS cannot co-exist and current implementation requires two
fixes:
1) stmmac_open() does not need to call stmmac_enable_tbs() because
the MAC is reset in stmmac_init_dma_engine() anyway.
2) Inside stmmac_hw_setup(), we should call stmmac_enable_tso() for
TX Q that is _not_ configured for TBS.
Fixes: 579a25a854d4 ("net: stmmac: Initial support for TBS")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 9c63faaa931e443e7abbbee9de0169f1d4710546, which
introduces a suspend/resume regression on Jetson TX2 boards that can be
reproduced every time. Given that the issue that this was supposed to
fix only occurs very sporadically the safest course of action is to
revert before v5.12 and then we can have another go at fixing the more
rare issue in the next release (and perhaps backport it if necessary).
The root cause of the observed problem seems to be that when the system
is suspended, some packets are still in transit. When the descriptors
for these buffers are cleared on resume, the descriptors become invalid
and cause a fatal bus error.
Link: https://lore.kernel.org/r/708edb92-a5df-ecc4-3126-5ab36707e275@nvidia.com/
Reported-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Synopsis MAC controller supports auxiliary snapshot feature that
allows user to store a snapshot of the system time based on an external
event.
This patch add supports to the above mentioned feature. Users will be
able to triggered capturing the time snapshot from user-space using
application such as testptp or any other applications that uses the
PTP_EXTTS_REQUEST ioctl request.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Tan Tee Min <tee.min.tan@intel.com>
Co-developed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add the support of XDP ZC TX submission and cleaning into
stmmac_tx_clean(). The function is made to clean as many TX complete
frames as possible, i.e. limit by priv->dma_tx_size instead of NAPI
budget. For TX ring that is associated with XSK pool, the function
stmmac_xdp_xmit_zc() is introduced to TX frame buffers from XSK pool by
using xsk_tx_peek_desc(). To make stmmac_tx_clean() support the cleaning
of XSK TX frames, STMMAC_TXBUF_T_XSK_TX TX buffer type is introduced.
As stmmac_tx_clean() uses the return value to cue whether NAPI function
should continue to poll, we augment the caller of stmmac_tx_clean() to
pass NAPI budget instead of priv->dma_tx_size through 'budget' input and
made stmmac_tx_clean() to always clean up-to the TX ring size instead.
This allows us to use the return boolean status of stmmac_xdp_xmit_zc()
to decide if XSK TX work is done or not: If true, set 'xmits' to return
'budget - 1' so that NAPI poll may exit. Else, set 'xmits' to return
'budget' to make NAPI poll continue to poll since XSK TX work is not
done. Finally, at the end of stmmac_tx_clean(), the function now take
a maximum value between 'count' and 'xmits' so that status from both
TX cleaning and XSK TX (only for XDP ZC) is considered.
This patch adds a new NAPI poll called stmmac_napi_poll_rxtx() that is
meant to be enabled/disabled for RX and TX ring that are bound to XSK
pool. This NAPI poll function starts with cleaning TX ring, then submits
XSK TX frames to TX ring before proceed to perform RX operations, i.e.
, receiving RX frames and replenishing RX ring with RX free buffers
obtained from XSK pool. Therefore, during XSK RX and TX setup, the driver
enables stmmac_napi_poll_rxtx() for RX and TX operations, then during
XSK RX and TX pool tear-down, the driver reenables the exisiting
independent NAPI poll functions accordingly: stmmac_napi_poll_rx() and
stmmac_napi_poll_tx().
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support for receiving packet via AF_XDP zero-copy
mechanism.
XDP ZC uses 1:1 mapping of XDP buffer to receive packet, therefore the
use of split header is not used currently. The 'xdp_buff' is declared as
union together with a struct that contains 'page', 'addr' and
'page_offset' that are associated with primary buffer.
RX buffers are now allocated either via page_pool or xsk pool. For RX
buffers from xsk_pool they are allocated and deallocated using below
functions:
* stmmac_alloc_rx_buffers_zc(struct stmmac_priv *priv, u32 queue)
* dma_free_rx_xskbufs(struct stmmac_priv *priv, u32 queue)
With above functions now available, we then extend the following driver
functions to support XDP ZC:
* stmmac_reinit_rx_buffers()
* __init_dma_rx_desc_rings()
* init_dma_rx_desc_rings()
* __free_dma_rx_desc_resources()
Note: stmmac_alloc_rx_buffers_zc() may return -ENOMEM due to RX XDP
buffer pool is not allocated (e.g. samples/bpf/xdpsock TX-only). But,
it is still ok to let TX XDP ZC to continue, therefore, the -ENOMEM
is silently ignored to let the driver succcessfully transition to XDP
ZC mode for the said RX and TX queue.
As XDP ZC buffer size is different, the DMA buffer size is required
to be reprogrammed accordingly for RX DMA/Queue that is populated with
XDP buffer from XSK pool.
Next, to add or remove per-queue XSK pool, stmmac_xdp_setup_pool()
will call stmmac_xdp_enable_pool() or stmmac_xdp_disable_pool()
that in-turn coordinates the tearing down and setting up RX ring via
RX buffers and descriptors removal and reallocation through
stmmac_disable_rx_queue() and stmmac_enable_rx_queue(). In addition,
stmmac_xsk_wakeup() is added to initiate XDP RX buffer replenishing
by signalling user application to add available XDP frames back to
FILL queue.
For RX processing using XDP zero-copy buffer, stmmac_rx_zc() is
introduced which is implemented with the assumption that RX split
header is disabled. For XDP verdict is XDP_PASS, the XDP buffer is
copied into a sk_buff allocated through stmmac_construct_skb_zc()
and sent to Linux network GRO inside stmmac_dispatch_skb_zc(). Free RX
buffers are then replenished using stmmac_rx_refill_zc()
v2: introduce __stmmac_disable_all_queues() to contain the original code
that does napi_disable() and then make stmmac_setup_tc_block_cb()
to use it. Move synchronize_rcu() into stmmac_disable_all_queues()
that eventually calls __stmmac_disable_all_queues(). Then,
make both stmmac_release() and stmmac_suspend() to use
stmmac_disable_all_queues(). Thanks David Miller for spotting the
synchronize_rcu() issue in v1 patch.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare stmmac_xdp_run_prog() for AF_XDP zero-copy support which will be
added by upcoming patches by splitting out the XDP verdict processing
into __stmmac_xdp_run_prog() and it callable for XDP ZC path which does
not need to verify bpf_prog is not NULL.
The stmmac_xdp_run_prog() is used for regular XDP Rx path which requires
bpf_prog to be verified.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Below functions are made to be per-queue in preparation of XDP ZC:
__init_dma_rx_desc_rings(struct stmmac_priv *priv, u32 queue, gfp_t flags)
__init_dma_tx_desc_rings(struct stmmac_priv *priv, u32 queue)
The original functions below are stay maintained for all queue usage:
init_dma_rx_desc_rings(struct net_device *dev, gfp_t flags)
init_dma_tx_desc_rings(struct net_device *dev)
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The per-queue RX buffer allocation in stmmac_reinit_rx_buffers() can be
made to use stmmac_alloc_rx_buffers() by merging the page_pool alloc
checks for "buf->page" and "buf->sec_page" in stmmac_init_rx_buffers().
This is in preparation for XSK pool allocation later.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange RX buffer page_pool recycling logics into dma_recycle_rx_skbufs,
so that we prepare stmmac_reinit_rx_buffers() for XSK pool expansion.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch restructures the per RX queue buffer allocation from page_pool
to stmmac_alloc_rx_buffers().
We also rearrange dma_free_rx_skbufs() so that it can be used in
init_dma_rx_desc_rings() during freeing of RX buffer in the event of
page_pool allocation failure to replace the more efficient method earlier.
The replacement is needed to make the RX buffer alloc and free method
scalable to XDP ZC xsk_pool alloc and free later.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of XDP_REDIRECT to another remote cpu for
further action. It also implements ndo_xdp_xmit ops, enabling the driver
to transmit packets forwarded to it by XDP program running on another
interface.
This patch has been tested using "xdp_redirect_cpu" for XDP_REDIRECT
+ drop testing. It also been tested with "xdp_redirect" sample app
which can be used to exercise ndo_xdp_xmit ops. The burst traffics are
generated using pktgen_sample03_burst_single_flow.sh in samples/pktgen
directory.
v4: Move xdp_do_flush() processing into stmmac_finalize_xdp_rx() and
combined the XDP verdict of XDP TX and REDIRECT together.
v3: Added 'nq->trans_start = jiffies' to avoid TX time-out as we are
sharing TX queue between slow path and XDP. Thanks to Jakub Kicinski
for point out.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for XDP_TX action which enables XDP program to
transmit back received frames.
This patch has been tested with the "xdp2" app located in samples/bpf
dir. The DUT receives burst traffic packet generated using pktgen script
'pktgen_sample03_burst_single_flow.sh'.
v4: Moved stmmac_tx_timer_arm() to be done once at the end of NAPI RX.
Fixed stmmac_xdp_xmit_back() to return STMMAC_XDP_CONSUMED if
XDP buffer to frame conversion fails. Thanks to Jakub's input.
v3: Added 'nq->trans_start = jiffies' to avoid TX time-out as we are
sharing TX queue between slow path and XDP. Thanks to Jakub Kicinski
for pointing out.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the initial XDP support to stmmac driver. It supports
XDP_PASS, XDP_DROP and XDP_ABORTED actions. Upcoming patches will add
support for XDP_TX and XDP_REDIRECT.
To support XDP headroom, this patch adds page_offset into RX buffer and
change the dma_sync_single_for_device|cpu(). The DMA address used for
RX operation are changed to take into page_offset too. As page_pool
can handle dma_sync_single_for_device() on behalf of driver with
PP_FLAG_DMA_SYNC_DEV flag, we skip doing that in stmmac driver.
Current stmmac driver supports split header support (SPH) in RX but
the flexibility of splitting header and payload at different position
makes it very complex to be supported for XDP processing. In addition,
jumbo frame is not supported in XDP to keep the initial codes simple.
This patch has been tested with the sample app "xdp1" located in
samples/bpf directory for both SKB and Native (XDP) mode. The burst
traffic generated using pktgen_sample03_burst_single_flow.sh in
samples/pktgen directory.
Changes in v3:
- factor in xdp header and tail adjustment done by XDP program.
Thanks to Jakub Kicinski for pointing out the gap in v2.
Changes in v2:
- fix for "warning: variable 'len' set but not used" reported by lkp.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch organizes TX tail pointer update into a new function called
stmmac_flush_tx_descriptors() so that we can reuse it in stmmac_xmit(),
stmmac_tso_xmit() and up-coming XDP implementation.
Changes to v2:
- Fix for warning: unused variable ‘desc_size’
https://patchwork.hopto.org/static/nipa/457321/12170149/build_32bit/stderr
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SPH functionality splits header and payload according to split mode and
offsef fields (SPLM and SPLOFST). It is beneficials for Linux network
stack RX processing however it adds a lot of complexity in XDP
processing.
So, this patch makes the split-header (SPH) capability of the controller
is stored in "priv->sph_cap" and the enabling/disabling of SPH is decided
by "priv->sph".
This is to prepare initial XDP enabling for stmmac to disable the use of
SPH whenever XDP is enabled.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain platform likes Intel mGBE has independent hardware IRQ resources
for TX and RX DMA operation. In preparation to support XDP TX, we add IRQ
affinity hint to group both RX and TX queue of the same queue ID to the
same CPU.
Changes in v2:
- IRQ affinity hint need to set to null before IRQ is released.
Thanks to issue reported by Song, Yoong Siang.
Reported-by: Song, Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing unlock before return from stmmac_suspend()
in the error handling case.
Fixes: 5ec55823438e ("net: stmmac: add clocks management for gmac driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this patch, "net: stmmac: support FPE link partner hand-shaking
procedure", priv->plat->fpe_cfg wouldn`t be "devm_kzalloc"ed if
dma_cap->frpsel is 0 (Flexible Rx Parser is not supported in SoC) in
tc_init(). So, fpe_cfg will be remain as NULL and accessing it will cause
kernel panic.
To fix this, move the "devm_kzalloc"ing of priv->plat->fpe_cfg before
dma_cap->frpsel checking in tc_init(). Additionally, checking of
priv->dma_cap.fpesel is added before calling stmmac_fpe_link_state_handle()
as only FPE supported SoC is allowed to call the function.
Below is the kernel panic dump reported by Marek Szyprowski
<m.szyprowski@samsung.com>:
meson8b-dwmac ff3f0000.ethernet eth0: PHY [0.0:00] driver [RTL8211F Gigabit Ethernet] (irq=35)
meson8b-dwmac ff3f0000.ethernet eth0: No Safety Features support found
meson8b-dwmac ff3f0000.ethernet eth0: PTP not supported by HW
meson8b-dwmac ff3f0000.ethernet eth0: configuring for phy/rgmii link mode
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000001
Mem abort info:
...
user pgtable: 4k pages, 48-bit VAs, pgdp=00000000044eb000
[0000000000000001] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
Modules linked in: dw_hdmi_i2s_audio dw_hdmi_cec meson_gxl realtek meson_gxbb_wdt snd_soc_meson_axg_sound_card dwmac_generic axg_audio meson_dw_hdmi crct10dif_ce snd_soc_meson_card_utils snd_soc_meson_axg_tdmout panfrost rc_odroid gpu_sched reset_meson_audio_arb meson_ir snd_soc_meson_g12a_tohdmitx snd_soc_meson_axg_frddr sclk_div clk_phase snd_soc_meson_codec_glue dwmac_meson8b snd_soc_meson_axg_fifo stmmac_platform meson_rng meson_drm stmmac rtc_meson_vrtc rng_core meson_canvas pwm_meson dw_hdmi mdio_mux_meson_g12a pcs_xpcs snd_soc_meson_axg_tdm_interface snd_soc_meson_axg_tdm_formatter nvmem_meson_efuse display_connector
CPU: 1 PID: 7 Comm: kworker/u8:0 Not tainted 5.12.0-rc4-next-20210325+
Hardware name: Hardkernel ODROID-C4 (DT)
Workqueue: events_power_efficient phylink_resolve
pstate: 20400009 (nzCv daif +PAN -UAO -TCO BTYPE=--)
pc : stmmac_mac_link_up+0x14c/0x348 [stmmac]
lr : stmmac_mac_link_up+0x284/0x348 [stmmac] ...
Call trace:
stmmac_mac_link_up+0x14c/0x348 [stmmac]
phylink_resolve+0x104/0x420
process_one_work+0x2a8/0x718
worker_thread+0x48/0x460
kthread+0x134/0x160
ret_from_fork+0x10/0x18
Code: b971ba60 350007c0 f958c260 f9402000 (39400401)
---[ end trace 0c9deb6c510228aa ]---
Fixes: 5a5586112b92 ("net: stmmac: support FPE link partner hand-shaking
procedure")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For interrupt mode INTM=0, TX/RX transfer complete will trigger signal
not only on sbd_perch_[tx|rx]_intr_o (Transmit/Receive Per Channel) but
also on the sbd_intr_o (Common).
As for multi-MSI implementation, setting interrupt mode INTM=1 is more
efficient as each TX intr and RX intr (TI/RI) will be handled by TX/RX ISR
without the need of calling the common MAC ISR.
Updated the TX/RX NORMAL interrupts status checking process as the
NIS status bit is not asserted for any RI/TI events for INTM=1.
Signed-off-by: Wong, Vee Khee <vee.khee.wong@intel.com>
Co-developed-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we introduce MSI interrupt service routines and hook these routines
up if stmmac_open() sees valid irq line being requested:-
stmmac_mac_interrupt() :- MAC (dev->irq), WOL (wol_irq), LPI (lpi_irq)
stmmac_safety_interrupt() :- Safety Feat Correctible Error (sfty_ce_irq)
& Uncorrectible Error (sfty_ue_irq)
stmmac_msi_intr_rx() :- For all RX MSI irq (rx_irq)
stmmac_msi_intr_tx() :- For all TX MSI irq (tx_irq)
Each of IRQs will have its unique name so that we can differentiate
them easily under /proc/interrupts.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor stmmac_interrupt() by introducing stmmac_common_interrupt()
so that we prepare the ISR operation to be friendly to MSI later.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to make stmmac support multi-vector MSI, we introduce the
interrupt status masking according to RX, TX or RXTX. Default to use RXTX
inside stmmac_dma_interrupt(), so there is no run-time logic difference
now.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to discover whether remote station supports frame preemption,
local station sends verify mPacket and expects response mPacket in
return from the remote station.
So, we add the functions to send and handle event when verify mPacket
and response mPacket are exchanged between the networked stations.
The mechanism to handle different FPE states between local and remote
station (link partner) is implemented using workqueue which starts a
task each time there is some sign of verify & response mPacket exchange
as check in FPE IRQ event. The task retries couple of times to try to
spot the states that both stations are ready to enter FPE ON. This allows
different end points to enable FPE at different time and verify-response
mPacket can happen asynchronously. Ultimately, the task will only turn
FPE ON when local station have both exchange response in both directions.
Thanks to Voon Weifeng for implementing the core functions for detecting
FPE events and send mPacket and phylink related change.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Co-developed-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Co-developed-by: Tan Tee Min <tee.min.tan@intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@intel.com>
Co-developed-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Below EST errors are added into ethtool statistic:
1) Constant Gate Control Error (CGCE):
The counter "mtl_est_cgce" increases everytime CGCE interrupt is
triggered.
2) Head-of-Line Blocking due to Scheduling (HLBS):
The counter "mtl_est_hlbs" increases everytime HLBS interrupt is
triggered.
3) Head-of-Line Blocking due to Frame Size (HLBF):
The counter "mtl_est_hlbf" increases everytime HLBF interrupt is
triggered.
4) Base Time Register error (BTRE):
The counter "mtl_est_btre" increases everytime BTRE interrupt is
triggered but BTRL not reaches maximum value of 15.
5) Base Time Register Error Loop Count (BTRL) reaches maximum value:
The counter "mtl_est_btrlm" increases everytime BTRE interrupt is
triggered and BTRL value reaches maximum value of 15.
Please refer to MTL_EST_STATUS register in DesignWare Cores Ethernet
Quality-of-Service Databook for more detail explanation.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Co-developed-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabled EST related interrupts as below:
1) Constant Gate Control Error (CGCE)
2) Head-of-Line Blocking due to Scheduling (HLBS)
3) Head-of-Line Blocking due to Frame Size (HLBF).
4) Base Time Register error (BTRE)
5) Switch to S/W owned list Complete (SWLC)
For HLBS, the user will get the info of all the queues that shows this
error. For HLBF, the user will get the info of all the queue with the
latest frame size which causes the error. Frame size 0 indicates no
error.
The ISR handling takes place when EST feature is enabled by user.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Co-developed-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extending the driver to support per-queue RX and TX coalesce settings in
order to support below commands:
To show per-queue coalesce setting:-
$ ethtool --per-queue <DEVNAME> queue_mask <MASK> --show-coalesce
To set per-queue coalesce setting:-
$ ethtool --per-queue <DEVNAME> queue_mask <MASK> --coalesce \
[rx-usecs N] [rx-frames M] [tx-usecs P] [tx-frames Q]
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
