IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit fa5d0a0205c34734c5b8daa77e39ac2817f63a10 ]
In the dsi_enable function, mtk_dsi_rxtx_control is to
pull up the MIPI signal operation. Before dsi_disable,
MIPI should also be pulled down by writing a register
instead of disabling dsi.
If disable dsi without pulling the mipi signal low, the value of
the register will still maintain the setting of the mipi signal being
pulled high.
After resume, even if the mipi signal is not pulled high, it will still
be in the high state.
Fixes: 2e54c14e310f ("drm/mediatek: Add DSI sub driver")
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1653012007-11854-5-git-send-email-xinlei.lee@mediatek.com/
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cde7e2e35c2866d22a3a012e72a41052dfcc255d ]
In order to match the changes of "Use the drm_panel_bridge API",
the poweron/poweroff of dsi is extracted from enable/disable and
defined as new funcs (atomic_pre_enable/atomic_post_disable).
Since dsi_poweron is moved from dsi_enable to pre_enable function, in
order to avoid poweron failure, the operation of dsi register fails to
cause bus hang. Therefore, the protection mechanism is added to the
dsi_enable function.
Fixes: 2dd8075d2185 ("drm/mediatek: mtk_dsi: Use the drm_panel_bridge API")
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1653012007-11854-3-git-send-email-xinlei.lee@mediatek.com/
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 136f614931a2bb73616b292cf542da3a18daefd5 ]
The last case label can write two buffers 'mc_reg_address[j]' and
'mc_data[j]' with 'j' offset equal to SMC_NISLANDS_MC_REGISTER_ARRAY_SIZE
since there are no checks for this value in both case labels after the
last 'j++'.
Instead of changing '>' to '>=' there, add the bounds check at the start
of the second 'case' (the first one already has it).
Also, remove redundant last checks for 'j' index bigger than array size.
The expression is always false. Moreover, before or after the patch
'table->last' can be equal to SMC_NISLANDS_MC_REGISTER_ARRAY_SIZE and it
seems it can be a valid value.
Detected using the static analysis tool - Svace.
Fixes: 69e0b57a91ad ("drm/radeon/kms: add dpm support for cayman (v5)")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9331f7d3c54a263bede5055e106e40b28d0bd937 ]
Currently a couple of debug_mask entries are mapped to the same value,
this could enable unintended driver logging. If enabling DP_TX logs was
the intention, then this could also enable PCI logs flooding the dmesg
buffer or vice versa. Fix this by correctly assigning the debug masks.
Found during code review.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Fixes: aa2092a9bab3f ("ath11k: add raw mode and software crypto support")
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220602115621.15339-1-quic_mpubbise@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 435c249008cba04ed6a7975e9411f3b934620204 ]
In __spi_validate, there's a validation that no partial transfers
are accepted (xfer->len % w_size must be zero). When
max_chunk is not a multiple of bpw (e.g. max_chunk = 65535,
bpw = 16), the transfer will be rejected.
This patch aligns max_chunk to 2 bytes (the maximum value of bpw is 16),
so that no partial transfer will occur.
Fixes: d23d4d4dac01 ("drm/tinydrm: Move tinydrm_spi_transfer()")
Signed-off-by: Yunhao Tian <t123yh.xyz@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510030219.2486687-1-t123yh.xyz@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4ba1ff87b17e81686ada8f429300876f55f95ad ]
Make sure to allocate resources needed before registering the device.
This specifically avoids having a racing open() trigger a BUG_ON() in
mod_timer() when ath11k_mac_op_start() is called before the
mon_reap_timer as been set up.
I did not see this issue with next-20220310, but I hit it on every probe
with next-20220511. Perhaps some timing changed in between.
Here's the backtrace:
[ 51.346947] kernel BUG at kernel/time/timer.c:990!
[ 51.346958] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
...
[ 51.578225] Call trace:
[ 51.583293] __mod_timer+0x298/0x390
[ 51.589518] mod_timer+0x14/0x20
[ 51.595368] ath11k_mac_op_start+0x41c/0x4a0 [ath11k]
[ 51.603165] drv_start+0x38/0x60 [mac80211]
[ 51.610110] ieee80211_do_open+0x29c/0x7d0 [mac80211]
[ 51.617945] ieee80211_open+0x60/0xb0 [mac80211]
[ 51.625311] __dev_open+0x100/0x1c0
[ 51.631420] __dev_change_flags+0x194/0x210
[ 51.638214] dev_change_flags+0x24/0x70
[ 51.644646] do_setlink+0x228/0xdb0
[ 51.650723] __rtnl_newlink+0x460/0x830
[ 51.657162] rtnl_newlink+0x4c/0x80
[ 51.663229] rtnetlink_rcv_msg+0x124/0x390
[ 51.669917] netlink_rcv_skb+0x58/0x130
[ 51.676314] rtnetlink_rcv+0x18/0x30
[ 51.682460] netlink_unicast+0x250/0x310
[ 51.688960] netlink_sendmsg+0x19c/0x3e0
[ 51.695458] ____sys_sendmsg+0x220/0x290
[ 51.701938] ___sys_sendmsg+0x7c/0xc0
[ 51.708148] __sys_sendmsg+0x68/0xd0
[ 51.714254] __arm64_sys_sendmsg+0x28/0x40
[ 51.720900] invoke_syscall+0x48/0x120
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Fixes: 840c36fa727a ("ath11k: dp: stop rx pktlog before suspend")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220517103436.15867-1-johan+linaro@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b88d28146c30a8e14f0f012d56ebf19b68a348f4 ]
If the copy_from_user() fails or the user gives invalid date then the
correct thing to do is to return a negative error code. (Currently it
returns success).
I made a copy additional related cleanups:
1) There is no need to check "buffer" for NULL. That's handled by
copy_from_user().
2) The "h2c_len" variable cannot be negative because it is unsigned
and because sscanf() does not return negative error codes.
Fixes: 610247f46feb ("rtlwifi: Improve debugging by using debugfs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/YoOLnDkHgVltyXK7@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ad6f181ad9a19a26bda73a7b199df44ccfcdaba ]
The SPI core always reports a "MODALIAS=spi:<foo>", even if the device was
registered via OF. This means that the st7735r.ko module won't autoload if
a DT has a node with a compatible "okaya,rh128128t" string.
In that case, kmod expects a "MODALIAS=of:N*T*Cokaya,rh128128t" uevent but
instead will get a "MODALIAS=spi:rh128128t", which is not present in the
list of aliases:
$ modinfo drivers/gpu/drm/tiny/st7735r.ko | grep alias
alias: of:N*T*Cokaya,rh128128tC*
alias: of:N*T*Cokaya,rh128128t
alias: of:N*T*Cjianda,jd-t18003-t01C*
alias: of:N*T*Cjianda,jd-t18003-t01
alias: spi:jd-t18003-t01
To workaround this issue, add in the SPI table an entry for that device.
Fixes: d1d511d516f7 ("drm: tiny: st7735r: Add support for Okaya RH128128T")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220520091602.179078-1-javierm@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ee6c5abebd3cacf2ac4378d0ed4f57fd4850421 ]
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge rising - but instead rely on Devicetree to configure it.
All Qualcomm DTSI with WCN3990 define the interrupt type as level high,
so the mismatch between DTSI and driver causes rebind issues:
$ echo 18800000.wifi > /sys/bus/platform/drivers/ath10k_snoc/unbind
$ echo 18800000.wifi > /sys/bus/platform/drivers/ath10k_snoc/bind
[ 44.763114] irq: type mismatch, failed to map hwirq-446 for interrupt-controller@17a00000!
[ 44.763130] ath10k_snoc 18800000.wifi: error -ENXIO: IRQ index 0 not found
[ 44.763140] ath10k_snoc 18800000.wifi: failed to initialize resource: -6
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.0.c8-00009-QCAHLSWSC8180XMTPLZ-1
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
Fixes: c963a683e701 ("ath10k: add resource init and deinit for WCN3990")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220513151516.357549-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b4c48f3e315d172e4cc06e10f2c8ba180788baf ]
The Refclk may be supplied by SoC clock output instead of crystal
oscillator, make sure the clock are enabled before any other action
is performed with the bridge chip, otherwise it may either fail to
operate at all, or miss reset GPIO toggle.
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: 7caff0fc4296e ("drm/bridge: tc358767: Add DPI to eDP bridge driver")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220520121543.11550-1-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8478095a8c4bcea3c83b0767d6c9127434160761 ]
The TC358767/TC358867/TC9595 are all capable of operating in multiple
modes, DPI-to-(e)DP, DSI-to-(e)DP, DSI-to-DPI. Only the first mode is
currently supported. In order to support the rest of the modes without
making the tc_probe() overly long, split the bridge endpoint parsing
into dedicated function, where the necessary logic to detect the bridge
mode based on which endpoints are connected, can be implemented.
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de> # In both DPI to eDP and DSI to DPI mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220329085015.39159-7-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2375e964d541bb09158cd2dff67b5d74e8de61cd ]
The PWMs are expected to be functional until pwmchip_remove() is called.
So disable the clks only afterwards.
Fixes: 9e37a53eb051 ("pwm: sifive: Add a driver for SiFive SoC PWM")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ace41d7564e655c39f709a78c035188a460c7cbd ]
.apply() assumes the clk to be for a given PWM iff the PWM is enabled.
So make sure this is the case when .probe() completes. And in .remove()
disable the according number of times.
This fixes a clk enable/disable imbalance, if some PWMs are already running
at probe time.
Fixes: 9e37a53eb051 (pwm: sifive: Add a driver for SiFive SoC PWM)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20550a61880fc55e68a0d290ad195b74729c0e7b ]
Instead of explicitly using PWM_SIFIVE_PWMCMP0 + pwm->hwpwm *
PWM_SIFIVE_SIZE_PWMCMP for each access to one of the PWMCMP registers,
introduce a macro that takes the hwpwm id as parameter.
For the register definition using a plain 4 instead of the cpp constant
PWM_SIFIVE_SIZE_PWMCMP is easier to read, so define the offset macro
without the constant. The latter can then be dropped as there are no
users left.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ceb2c2842f3664dcc4e6d8cb317e1e83bb81b1e5 ]
pwmchip_remove() returns always 0. Don't use the value to make it
possible to eventually change the function to return void. Also the
driver core ignores the return value of pwm_sifive_remove().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e120a5f1e78fab6223544e425015f393d90d6f0d ]
Otherwise PR ops may be issued while the broader DM device is being
reconfigured, etc.
Fixes: 9c72bad1f31a ("dm: call PR reserve/unreserve on each underlying device")
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cf51bfe999524377fbb71becb583b4ca6d07cfc ]
Include sys/time.h and pthread.h in tmon.h, so that types
"pthread_mutex_t" and "struct timeval tv" are known when tmon.h
references them.
Without these headers, compiling tmon against musl-libc will fail with
these errors:
In file included from sysfs.c:31:0:
tmon.h:47:8: error: unknown type name 'pthread_mutex_t'
extern pthread_mutex_t input_lock;
^~~~~~~~~~~~~~~
make[3]: *** [<builtin>: sysfs.o] Error 1
make[3]: *** Waiting for unfinished jobs....
In file included from tui.c:31:0:
tmon.h:54:17: error: field 'tv' has incomplete type
struct timeval tv;
^~
make[3]: *** [<builtin>: tui.o] Error 1
make[2]: *** [Makefile:83: tmon] Error 2
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Acked-by: Alejandro González <alejandro.gonzalez.correo@gmail.com>
Tested-by: Alejandro González <alejandro.gonzalez.correo@gmail.com>
Fixes: 94f69966faf8 ("tools/thermal: Introduce tmon, a tool for thermal subsystem")
Link: https://lore.kernel.org/r/20220718031040.44714-1-f.fainelli@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ce4b78f73e8e00fb86bad67ee7f6fe12019707e ]
clang has -Wconstant-conversion by default, and the constant 0xAAAAAAAAA
(9 As) being converted to an int, which is generally 32 bits, results
in the compile warning:
clang -Wl,-no-as-needed -Wall -isystem ../../../../usr/include/ -lpthread seccomp_bpf.c -lcap -o seccomp_bpf
seccomp_bpf.c:812:67: warning: implicit conversion from 'long' to 'int' changes value from 45812984490 to -1431655766 [-Wconstant-conversion]
int kill = kill_how == KILL_PROCESS ? SECCOMP_RET_KILL_PROCESS : 0xAAAAAAAAA;
~~~~ ^~~~~~~~~~~
1 warning generated.
-1431655766 is the expected truncation, 0xAAAAAAAA (8 As), so use
this directly in the code to avoid the warning.
Fixes: 3932fcecd962 ("selftests/seccomp: Add test for unknown SECCOMP_RET kill behavior")
Signed-off-by: YiFei Zhu <zhuyifei@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220526223407.1686936-1-zhuyifei@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c66d1b9b30f737fcef85a0b75bfe0590e16b62a ]
dequeue_task_rt() only decrements 'rt_rq->rt_nr_running' after having
called sched_update_tick_dependency() preventing it from re-enabling the
tick on systems that no longer have pending SCHED_RT tasks but have
multiple runnable SCHED_OTHER tasks:
dequeue_task_rt()
dequeue_rt_entity()
dequeue_rt_stack()
dequeue_top_rt_rq()
sub_nr_running() // decrements rq->nr_running
sched_update_tick_dependency()
sched_can_stop_tick() // checks rq->rt.rt_nr_running,
...
__dequeue_rt_entity()
dec_rt_tasks() // decrements rq->rt.rt_nr_running
...
Every other scheduler class performs the operation in the opposite
order, and sched_update_tick_dependency() expects the values to be
updated as such. So avoid the misbehaviour by inverting the order in
which the above operations are performed in the RT scheduler.
Fixes: 76d92ac305f2 ("sched: Migrate sched to use new tick dependency mask model")
Signed-off-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <vschneid@redhat.com>
Reviewed-by: Phil Auld <pauld@redhat.com>
Link: https://lore.kernel.org/r/20220628092259.330171-1-nsaenzju@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92f2b8bafa3d6e89c750e9d301a8b7ab76aaa8b6 ]
The arm_spe_pmu driver will enable SYS_PMSCR_EL1.CX in order to add CONTEXT
packets into the traces, if the owner of the perf event runs with required
capabilities i.e CAP_PERFMON or CAP_SYS_ADMIN via perfmon_capable() helper.
The value of this bit is computed in the arm_spe_event_to_pmscr() function
but the check for capabilities happens in the pmu event init callback i.e
arm_spe_pmu_event_init(). This suggests that the value of the CX bit should
remain consistent for the duration of the perf session.
However, the function arm_spe_event_to_pmscr() may be called later during
the event start callback i.e arm_spe_pmu_start() when the "current" process
is not the owner of the perf session, hence the CX bit setting is currently
not consistent.
One way to fix this, is by caching the required value of the CX bit during
the initialization of the PMU event, so that it remains consistent for the
duration of the session. It uses currently unused 'event->hw.flags' element
to cache perfmon_capable() value, which can be referred during event start
callback to compute SYS_PMSCR_EL1.CX. This ensures consistent availability
of context packets in the trace as per event owner capabilities.
Drop BIT(SYS_PMSCR_EL1_CX_SHIFT) check in arm_spe_pmu_event_init(), because
now CX bit cannot be set in arm_spe_event_to_pmscr() with perfmon_capable()
disabled.
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Fixes: d5d9696b0380 ("drivers/perf: Add support for ARMv8.2 Statistical Profiling Extension")
Reported-by: German Gomez <german.gomez@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20220714061302.2715102-1-anshuman.khandual@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58577966a42fc0b660b5e2c7c9e5a2241363ea83 ]
Currently the DT for QCS404 SoC has setup for 2 USB2 PHYs with one each
assigned to USB3 controller and USB2 controller. This assignment is
incorrect which only works by luck: as when each USB HCI comes up it
configures the *other* controllers PHY which is enough to make them
happy. If, for any reason, we were to disable one of the controllers then
both would stop working.
This was a difficult inconsistency to be caught which was found while
trying to enable USB support in u-boot. So with all the required drivers
ported to u-boot, I couldn't get the same USB storage device enumerated
in u-boot which was being enumerated fine by the kernel.
The root cause of the problem came out to be that I wasn't enabling USB2
PHY: "usb2_phy_prim" in u-boot. Then I realised that via simply disabling
the same USB2 PHY currently assigned to USB2 host controller in the
kernel disabled enumeration for USB3 host controller as well.
So fix this inconsistency by correctly assigning USB2 PHYs.
Fixes: 9375e7d719b3 ("arm64: dts: qcom: qcs404: Add USB devices and PHYs")
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220711083038.1518529-1-sumit.garg@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6232f2aa99ce470799992e99e0012945bb5308f ]
QCOM_RPMPD requires PM_GENERIC_DOMAINS/_OF, which in turns requires
CONFIG_PM. I forgot about the latter in my earlier patch (it's still
in -next as of the time of committing, hence no Fixes: tag). Fix it.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220707212158.32684-1-konrad.dybcio@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66efb665cd5ad69b27dca8571bf89fc6b9c628a4 ]
We should call the of_node_put() for the reference returned by
of_get_child_by_name() which has increased the refcount.
Fixes: 40e20d68bb3f ("regulator: of: Add support for parsing regulator_state for suspend state")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220715111027.391032-1-windhl@126.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22c80aac882f712897b88b7ea8f5a74ea19019df ]
Trace the remapped operation and its flags instead of only the data
direction of remapped operations. This issue was detected by analyzing
the warnings reported by sparse related to the new blk_opf_t type.
Reviewed-by: Jun'ichi Nomura <junichi.nomura@nec.com>
Cc: Mike Snitzer <snitzer@kernel.org>
Cc: Mike Christie <michael.christie@oracle.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Fixes: 1b9a9ab78b0a ("blktrace: use op accessors")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220714180729.1065367-11-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a54895fa057c67700270777f7661d8d3c7fda88a ]
The request_queue can trivially be derived from the request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5918036cfa8ded7aa8094db70295011ce2275447 ]
Adding a MODULE_ALIAS() to drivetemp will make the driver easier
for modprobe to autoprobe.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220712214624.1845158-1-linus.walleij@linaro.org
Fixes: 5b46903d8bf3 ("hwmon: Driver for disk and solid state drives with temperature sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3ec5d11554778c24ac8915e847223ed71d104fc ]
blk_mq_debugfs_register_hctx() can be called by blk_mq_update_nr_hw_queues
when gendisk isn't added yet, such as nvme tcp.
Fixes the warning of 'debugfs: Directory 'hctx0' with parent '/' already present!'
which can be observed reliably when running blktests nvme/005.
Fixes: 6cfc0081b046 ("blk-mq: no need to check return value of debugfs_create functions")
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220711090808.259682-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 448b5a1548d87c246c3d0c3df8480d3c6eb6c11a ]
Currently, vmap()s are avoided if physical addresses are
consecutive for decompressed buffers.
I observed that is very common for 4KiB pclusters since the
numbers of decompressed pages are almost 2 or 3.
However, such detection doesn't work for Highmem pages on
32-bit machines, let's fix it now.
Reported-by: Liu Jinbao <liujinbao1@xiaomi.com>
Fixes: 7fc45dbc938a ("staging: erofs: introduce generic decompression backend")
Link: https://lore.kernel.org/r/20220708101001.21242-1-hsiangkao@linux.alibaba.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b415bb7c976f1d595ed752001c0938f702645dab ]
Hook SDMMC1 CD up with CVM GPIO02 (SOC_GPIO11) used for card detection on J4
(uSD socket) on the carrier.
Fixes: ef633bfc21e9 ("arm64: tegra: Enable card detect for SD card on P2888")
Signed-off-by: Tamás Szűcs <tszucs@protonmail.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c98e6e683632386a3bd284acda4342e68aec4c41 ]
The bananapi R64 (BPI-R64) experiences wrong WPS button signals.
In OpenWrt pushing the WPS button while powering on the device will set
it to recovery mode. Currently, this also happens without any user
interaction. In particular, the wrong signals appear while booting the
device or restarting it, e.g. after doing a system upgrade. If the
device is in recovery mode the user needs to manually power cycle or
restart it.
The official BPI-R64 sources set the WPS button to GPIO_ACTIVE_LOW in
the device tree. This setting seems to suppress the unwanted WPS button
press signals. So this commit changes the button from GPIO_ACTIVE_HIGH to
GPIO_ACTIVE_LOW.
The official BPI-R64 sources can be found on
https://github.com/BPI-SINOVOIP/BPI-R64-openwrt
Fixes: 0b6286dd96c0 ("arm64: dts: mt7622: add bananapi BPI-R64 board")
Suggested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Link: https://lore.kernel.org/r/20220630111746.4098-1-vincent@systemli.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54872fea6a5ac967ec2272aea525d1438ac6735a ]
In error case in hisi_lpc_acpi_probe() after calling platform_device_add(),
hisi_lpc_acpi_remove() can't release the failed 'pdev', so it will be leak,
call platform_device_put() to fix this problem.
I'v constructed this error case and tested this patch on D05 board.
Fixes: 99c0228d6ff1 ("HISI LPC: Re-Add ACPI child enumeration support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6e0951414a314e7db3e9e24fd924b3e15515288 ]
Every iteration of for_each_available_child_of_node() decrements
the reference count of the previous node.
When breaking early from a for_each_available_child_of_node() loop,
we need to explicitly call of_node_put() on the child node.
Add missing of_node_put() to avoid refcount leak.
Fixes: 05589b30b21a ("soc: qcom: Extend AOSS QMP driver to support resources that are used to wake up the SoC.")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220606064252.42595-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92a563fcf14b3093226fb36f12e9b5cf630c5a5d ]
of_parse_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
of_node_put() will check NULL pointer.
Fixes: 88c1e9404f1d ("soc: qcom: add OCMEM driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220602042430.1114-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b13a3e5fd40b7d1b394c5ecbb5eb301a4c38e7b2 ]
When a platform marks a memory range as "special purpose" it is not
onlined as System RAM by default. However, it is still suitable for
error injection. Add IORES_DESC_SOFT_RESERVED to einj_error_inject() as
a permissible memory type in the sanity checking of the arguments to
_EINJ.
Fixes: 262b45ae3ab4 ("x86/efi: EFI soft reservation to E820 enumeration")
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reported-by: Omar Avelar <omar.avelar@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8977917e116d1571dacb8e9864474551c1c12bd ]
The PM8916 device specification [1] documents a programmable range of
1.75V to 3.337V with 12.5mV steps for the PMOS LDOs in PM8916. This
range is also used when controlling the regulator directly using the
qcom_spmi-regulator driver ("ult_pldo" there).
However, for some reason the qcom_smd-regulator driver allows a much
larger range for the same hardware component. This could be simply a
typo, since the start of the range is essentially just missing a '1'.
In practice this does not cause any major problems, since the driver
just sends the actual voltage to the RPM firmware instead of making use
of the incorrect voltage selector. Still, having the wrong range there
is confusing and prevents the regulator core from validating requests
correctly.
[1]: https://developer.qualcomm.com/download/sd410/pm8916pm8916-1-power-management-ic-device-specification.pdf
Fixes: 57d6567680ed ("regulator: qcom-smd: Add PM8916 support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Link: https://lore.kernel.org/r/20220623094614.1410180-2-stephan.gerhold@kernkonzept.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1ff2559cef0f6f8d97fba6337b28adb10689e16 ]
of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: 00f7dc636366 ("ARM: zynq: Add support for SOC_BUS")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220605082807.21526-1-linmq006@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 942228fbf5d4901112178b93d41225be7c0dd9de ]
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 1e037794f7f0 ("ARM: OMAP3+: PRM: register interrupt information from DT")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <20220526073724.21169-1-linmq006@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9705db1eff38d6b9114121f9e253746199b759c9 ]
omapdss_find_dss_of_node() calls of_find_compatible_node() to get device
node. of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() in later error path and normal path.
Fixes: e0c827aca0730 ("drm/omap: Populate DSS children in omapdss driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <20220601044858.3352-1-linmq006@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b82d9fa257cb3725c49d94d2aeafc4677c34448a ]
Returning 0 early from __bio_iov_append_get_pages() for the
max_append_sectors warning just creates an infinite loop since 0 means
success, and the bio will never fill from the unadvancing iov_iter. We
could turn the return into an error value, but it will already be turned
into an error value later on, so just remove the warning. Clearly no one
ever hit it anyway.
Fixes: 0512a75b98f84 ("block: Introduce REQ_OP_ZONE_APPEND")
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220610195830.3574005-2-kbusch@fb.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab3f045774f704c4e7b6a878102f4e9d4ae7bc74 ]
If both the model and the compatible properties are missing, then
machine will not be set. Initialize it with NULL.
Fixes: 34c1c21e94ac ("soc: fsl: fix section mismatch build warnings")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eae6d58d67d9739be5f7ae2dbead1d0ef6528243 ]
Commit dfd5e3f5fe27 ("locking/lockdep: Mark local_lock_t") added yet
another lockdep_init_map_*() variant, but forgot to update all the
existing users of the most complicated version.
This could lead to a loss of lock_type and hence an incorrect report.
Given the relative rarity of both local_lock and these annotations,
this is unlikely to happen in practise, still, best fix things.
Fixes: dfd5e3f5fe27 ("locking/lockdep: Mark local_lock_t")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/YqyEDtoan20K0CVD@worktop.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 506506cad3947b942425b119ffa2b06715d5d804 ]
Commit b20d1ba3cf4b ("arm64: cpufeature: allow for version discrepancy in
PMU implementations") made it possible to run Linux on a machine with PMUs
with different versions without tainting the kernel. The patch relaxed the
restriction only for the ID_AA64DFR0_EL1.PMUVer field, and missed doing the
same for ID_DFR0_EL1.PerfMon , which also reports the PMU version, but for
the AArch32 state.
For example, with Linux running on two clusters with different PMU
versions, the kernel is tainted when bringing up secondaries with the
following message:
[ 0.097027] smp: Bringing up secondary CPUs ...
[..]
[ 0.142805] Detected PIPT I-cache on CPU4
[ 0.142805] CPU features: SANITY CHECK: Unexpected variation in SYS_ID_DFR0_EL1. Boot CPU: 0x00000004011088, CPU4: 0x00000005011088
[ 0.143555] CPU features: Unsupported CPU feature variation detected.
[ 0.143702] GICv3: CPU4: found redistributor 10000 region 0:0x000000002f180000
[ 0.143702] GICv3: CPU4: using allocated LPI pending table @0x00000008800d0000
[ 0.144888] CPU4: Booted secondary processor 0x0000010000 [0x410fd0f0]
The boot CPU implements FEAT_PMUv3p1 (ID_DFR0_EL1.PerfMon, bits 27:24, is
0b0100), but CPU4, part of the other cluster, implements FEAT_PMUv3p4
(ID_DFR0_EL1.PerfMon = 0b0101).
Treat the PerfMon field as FTR_NONSTRICT and FTR_EXACT to pass the sanity
check and to match how PMUVer is treated for the 64bit ID register.
Fixes: b20d1ba3cf4b ("arm64: cpufeature: allow for version discrepancy in PMU implementations")
Signed-off-by: Alexandru Elisei <alexandru.elisei@arm.com>
Link: https://lore.kernel.org/r/20220617111332.203061-1-alexandru.elisei@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 113616ec5b64b23a1c9b663adafadabdfbec0f51 ]
Now that we handle all of the sections in a Hexagon defconfig, select
ARCH_WANT_LD_ORPHAN_WARN so that unhandled sections are warned about by
default.
Link: https://lkml.kernel.org/r/20210521011239.1332345-4-nathan@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Brian Cain <bcain@codeaurora.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Oliver Glitta <glittao@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 229e73d46994f15314f58b2d39bf952111d89193 ]
Make sure to free the platform device in the unlikely event that
registration fails.
Fixes: 7a67832c7e44 ("libnvdimm, e820: make CONFIG_X86_PMEM_LEGACY a tristate option")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220620140723.9810-1-johan@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
