IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 6afcf8ef0ca0a69d014f8edb613d94821f0ae700 upstream.
Since commit bda807d44454 ("mm: migrate: support non-lru movable page
migration") isolate_migratepages_block) can isolate !PageLRU pages which
would acct_isolated account as NR_ISOLATED_*. Accounting these non-lru
pages NR_ISOLATED_{ANON,FILE} doesn't make any sense and it can misguide
heuristics based on those counters such as pgdat_reclaimable_pages resp.
too_many_isolated which would lead to unexpected stalls during the
direct reclaim without any good reason. Note that
__alloc_contig_migrate_range can isolate a lot of pages at once.
On mobile devices such as 512M ram android Phone, it may use a big zram
swap. In some cases zram(zsmalloc) uses too many non-lru but
migratedable pages, such as:
MemTotal: 468148 kB
Normal free:5620kB
Free swap:4736kB
Total swap:409596kB
ZRAM: 164616kB(zsmalloc non-lru pages)
active_anon:60700kB
inactive_anon:60744kB
active_file:34420kB
inactive_file:37532kB
Fix this by only accounting lru pages to NR_ISOLATED_* in
isolate_migratepages_block right after they were isolated and we still
know they were on LRU. Drop acct_isolated because it is called after
the fact and we've lost that information. Batching per-cpu counter
doesn't make much improvement anyway. Also make sure that we uncharge
only LRU pages when putting them back on the LRU in
putback_movable_pages resp. when unmap_and_move migrates the page.
[mhocko@suse.com: replace acct_isolated() with direct counting]
Fixes: bda807d44454 ("mm: migrate: support non-lru movable page migration")
Link: http://lkml.kernel.org/r/20161019080240.9682-1-mhocko@kernel.org
Signed-off-by: Ming Ling <ming.ling@spreadtrum.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59749e6ce53735d8b696763742225f126e94603f upstream.
The radix tree counts valid entries in each tree node. Entries stored
in the tree cannot be removed by simpling storing NULL in the slot or
the internal counters will be off and the node never gets freed again.
When collapsing a shmem page fails, restore the holes that were filled
with radix_tree_insert() with a proper radix tree deletion.
Fixes: f3f0e1d2150b ("khugepaged: add support of collapse for tmpfs/shmem pages")
Link: http://lkml.kernel.org/r/20161117191138.22769-3-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Jan Kara <jack@suse.cz>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Matthew Wilcox <mawilcox@linuxonhyperv.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91a45f71078a6569ec3ca5bef74e1ab58121d80e upstream.
Patch series "mm: workingset: radix tree subtleties & single-page file
refaults", v3.
This is another revision of the radix tree / workingset patches based on
feedback from Jan and Kirill.
This is a follow-up to d3798ae8c6f3 ("mm: filemap: don't plant shadow
entries without radix tree node"). That patch fixed an issue that was
caused mainly by the page cache sneaking special shadow page entries
into the radix tree and relying on subtleties in the radix tree code to
make that work. The fix also had to stop tracking refaults for
single-page files because shadow pages stored as direct pointers in
radix_tree_root->rnode weren't properly handled during tree extension.
These patches make the radix tree code explicitely support and track
such special entries, to eliminate the subtleties and to restore the
thrash detection for single-page files.
This patch (of 9):
When a radix tree iteration drops the tree lock, another thread might
swoop in and free the node holding the current slot. The iteration
needs to do another tree lookup from the current index to continue.
[kirill.shutemov@linux.intel.com: re-lookup for replacement]
Fixes: f3f0e1d2150b ("khugepaged: add support of collapse for tmpfs/shmem pages")
Link: http://lkml.kernel.org/r/20161117191138.22769-2-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Matthew Wilcox <mawilcox@linuxonhyperv.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2a91f4f42018994d7424d405900d17eba6555d0 upstream.
PDF build on Kernel 4.9-rc? returns an error with Sphinx 1.3.x
and Sphinx 1.4.x, when trying to solve some cross-references.
The solution is to redefine the \DURole macro.
However, this is redefined too late. Move such redefinition to
LaTeX preamble and bind it to just the Sphinx versions where the
error is known to be present.
Tested by building the documentation on interactive mode:
make PDFLATEX=xelatex -C Documentation/output/./latex
Fixes: e61a39baf74d ("[media] index.rst: Fix LaTeX error in interactive mode on Sphinx 1.4.x")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3999f52e3198e76607446ab1a4610c1ddc406c56 upstream.
We cannot use the pte value used in set_pte_at for pte_same comparison,
because archs like ppc64, filter/add new pte flag in set_pte_at.
Instead fetch the pte value inside hugetlb_cow. We are comparing pte
value to make sure the pte didn't change since we dropped the page table
lock. hugetlb_cow get called with page table lock held, and we can take
a copy of the pte value before we drop the page table lock.
With hugetlbfs, we optimize the MAP_PRIVATE write fault path with no
previous mapping (huge_pte_none entries), by forcing a cow in the fault
path. This avoid take an addition fault to covert a read-only mapping
to read/write. Here we were comparing a recently instantiated pte (via
set_pte_at) to the pte values from linux page table. As explained above
on ppc64 such pte_same check returned wrong result, resulting in us
taking an additional fault on ppc64.
Fixes: 6a119eae942c ("powerpc/mm: Add a _PAGE_PTE bit")
Link: http://lkml.kernel.org/r/20161018154245.18023-1-aneesh.kumar@linux.vnet.ibm.com
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Reported-by: Jan Stancek <jstancek@redhat.com>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d74e7ed5dc1903ac081574a9b6aa94e7ba4ad45 upstream.
qcom_smd_send() should return -EAGAIN for non-blocking channels with
insufficient space, so that we can propagate this event to user space.
Fixes: 53e2822e56c7 ("rpmsg: Introduce Qualcomm SMD backend")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16652a936e96f5dae53c3fbd38a570497baadaa8 upstream.
We never set "ret" to RESULT_OK.
Fixes: 9f9c4180f88d ("mmc: mmc_test: add test for non-blocking transfers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0af52437254fda8b0cdbaae5a9b6d9327f1fcd5 upstream.
Commit 34c3d9819fda ("genirq/affinity: Provide smarter irq spreading
infrastructure") introduced a better IRQ spreading mechanism, taking
account of the available NUMA nodes in the machine.
Problem is that the algorithm of retrieving the nodemask iterates
"linearly" based on the number of online nodes - some architectures
present non-linear node distribution among the nodemask, like PowerPC.
If this is the case, the algorithm lead to a wrong node count number
and therefore to a bad/incomplete IRQ affinity distribution.
For example, this problem were found in a machine with 128 CPUs and two
nodes, namely nodes 0 and 8 (instead of 0 and 1, if it was linearly
distributed). This led to a wrong affinity distribution which then led to
a bad mq allocation for nvme driver.
Finally, we take the opportunity to fix a comment regarding the affinity
distribution when we have _more_ nodes than vectors.
Fixes: 34c3d9819fda ("genirq/affinity: Provide smarter irq spreading infrastructure")
Reported-by: Gabriel Krisman Bertazi <gabriel@krisman.be>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Gabriel Krisman Bertazi <gabriel@krisman.be>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: linux-pci@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: hch@lst.de
Link: http://lkml.kernel.org/r/1481738472-2671-1-git-send-email-gpiccoli@linux.vnet.ibm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bed570307ed78f21b77cb04a1df781dee4a8f05a upstream.
I noticed some wakeirq flakeyness with consumer drivers not using
autosuspend. For drivers not using autosuspend, the wakeirq may never
get unmasked in rpm_suspend() because of irq desc->depth.
We are configuring dedicated wakeirqs to start with IRQ_NOAUTOEN as we
naturally don't want them running until rpm_suspend() is called.
However, when a consumer driver initially calls pm_runtime_get(), we
now wrongly start with disable_irq_nosync() call on the dedicated
wakeirq that is disabled to start with.
This causes desc->depth to toggle between 1 and 2 instead of the usual
0 and 1. This can prevent enable_irq() from unmasking the wakeirq as
that only happens at desc->depth 1.
This does not necessarily show up with drivers using autosuspend as
there is time for disable_irq_nosync() before rpm_suspend() gets called
after the autosuspend timeout.
Let's fix the issue by adding wirq->status that lazily gets set on
the first rpm_suspend(). We also need PM runtime core private functions
for dev_pm_enable_wake_irq_check() and dev_pm_disable_wake_irq_check()
so we can enable the dedicated wakeirq on the first rpm_suspend().
While at it, let's also fix the comments for dev_pm_enable_wake_irq()
and dev_pm_disable_wake_irq(). Those can still be used by the consumer
drivers as needed because the IRQ core manages the interrupt usecount
for us.
Fixes: 4990d4fe327b (PM / Wakeirq: Add automated device wake IRQ handling)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1d111e073840b8dbc1ae90ba3fc274736451bdc upstream.
If msi_setup_entry() fails to allocate an affinity mask, it logs a message
but continues on and allocates an MSI entry with entry->affinity == NULL.
Check for this case in pci_irq_get_affinity() so we don't try to
dereference a NULL pointer.
[bhelgaas: changelog]
Fixes: ee8d41e53efe "pci/msi: Retrieve affinity for a vector"
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a11a18902bc3b904353063763d06480620245a6 upstream.
When the "policy" securityfs file is opened for read, it is opened as a
sequential file. However, when it is eventually released, there is no
cleanup for the sequential file, therefore some memory is leaked.
This patch adds a call to seq_release() in ima_release_policy() to clean up
the memory when the file is opened for read.
Fixes: 80eae209d63a IMA: allow reading back the current policy
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Eric Richter <erichte@linux.vnet.ibm.com>
Tested-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a29d0fbc2d9ad99fb8a981ab72548cc360e9d4c upstream.
Smatch complains that we started using the array offset before we
checked that it was valid.
Fixes: 017c59c042d0 ('relay: Use per CPU constructs for the relay channel buffer pointers')
Link: http://lkml.kernel.org/r/20161013084947.GC16198@mwanda
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8456066a57940b3884aa080c58b166567dc9de39 upstream.
Pass a task state as second argument to percpu_ida_alloc().
Fixes: commit 5a3ee221b543 ("sbp-target: Conversion to percpu_ida tag pre-allocation")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Chris Boot <bootc@bootc.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a91918cd3ea11f91c68e08e1e8ce1b560447a80e upstream.
This iscsit_tpg_add_portal_group() function is only called from
lio_target_tiqn_addtpg(). Both functions free the "tpg" pointer on
error so it's a double free bug. The memory is allocated in the caller
so it should be freed in the caller and not here.
Fixes: e48354ce078c ("iscsi-target: Add iSCSI fabric support for target v4.1")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: David Disseldorp <ddiss@suse.de>
[ bvanassche: Added "Fix" at start of patch title ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af15769ffab13d777e55fdef09d0762bf0c249c4 upstream.
gcc-7 notices that the condition in mvs_94xx_command_active looks
suspicious:
drivers/scsi/mvsas/mv_94xx.c: In function 'mvs_94xx_command_active':
drivers/scsi/mvsas/mv_94xx.c:671:15: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context]
This was introduced when the mv_printk() statement got added, and leads
to the condition being ignored. This is probably harmless.
Changing '&&' to '&' makes the code look reasonable, as we check the
command bit before setting and printing it.
Fixes: a4632aae8b66 ("[SCSI] mvsas: Add new macros and functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b93ca43b7e21fbe6fb1a6f4ecce4a2f70f424a0 upstream.
When a SW-configurable card is specified but not found, the driver
releases wrong region, causing the following message in kernel log:
Trying to free nonexistent resource <0000000000000000-000000000000000f>
Fix it by assigning base earlier.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Fixes: a8cfbcaec0c1 ("scsi: g_NCR5380: Stop using scsi_module.c")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5faf071d08ddd1c1be66deaa93a09ccf43f5b538 upstream.
Unfortunately, I seem to have missed a case where an IRQ safe spinlock was
required, in samsung_i2s_dai_remove, when I fixed up the other calls in
this patch:
316fa9e09ad7 ("ASoC: samsung: Use IRQ safe spin lock calls")
This causes a lockdep warning when unbinding and rebinding the audio card:
[ 104.357664] CPU0 CPU1
[ 104.362174] ---- ----
[ 104.366692] lock(&(&pri_dai->spinlock)->rlock);
[ 104.371372] local_irq_disable();
[ 104.377283] lock(&(&substream->self_group.lock)->rlock);
[ 104.385259] lock(&(&pri_dai->spinlock)->rlock);
[ 104.392469] <Interrupt>
[ 104.395072] lock(&(&substream->self_group.lock)->rlock);
[ 104.400710]
[ 104.400710] *** DEADLOCK ***
Fixes: ce8bcdbb61d9 ("ASoC: samsung: i2s: Protect more registers with a spinlock")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8eabf821cac120afb78ca251b07cbf520406a7e upstream.
"*val" is a u64. It definitely looks like we intend to use the high 32
bits as well.
Fixes: 700a9a63f9c1 ("ASoC: Intel: Skylake: Add module instance id generation APIs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Kranthi G <gudishax.kranthikumar@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a823a17981a73faa115bc0f7eda0190763075e2c upstream.
cht_bsw_rt5645 driver allocates the own codec_id string but doesn't
release it. For simplicity, put the string in cht_mc_private; then
the string is allocated in a shot and released altogether.
Fixes: c8560b7c917f ("ASoC: cht_bsw_rt5645: Fix writing to string literal")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b89e4b77ef9c2f985964fab17032db98f074ed0 upstream.
A bugfix accidentally removed the implicit initialization of the
dma channel number, causing undefined behavior when
v->alloc_dma_channel is NULL:
sound/soc/qcom/lpass-platform.c: In function ‘lpass_platform_pcmops_open’:
sound/soc/qcom/lpass-platform.c:83:29: error: ‘dma_ch’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
This adds back an explicit initialization to zero, restoring the
previous behavior for that case.
Fixes: 022d00ee0b55 ("ASoC: lpass-platform: Fix broken pcm data usage")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aec0e86172a79eb5e44aff1055bb953fe4d47c59 upstream.
We met the DMAR fault both on hpsa P420i and P421 SmartArray controllers
under kdump, it can be steadily reproduced on several different machines,
the dmesg log is like:
HP HPSA Driver (v 3.4.16-0)
hpsa 0000:02:00.0: using doorbell to reset controller
hpsa 0000:02:00.0: board ready after hard reset.
hpsa 0000:02:00.0: Waiting for controller to respond to no-op
DMAR: Setting identity map for device 0000:02:00.0 [0xe8000 - 0xe8fff]
DMAR: Setting identity map for device 0000:02:00.0 [0xf4000 - 0xf4fff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf6e000 - 0xbdf6efff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf6f000 - 0xbdf7efff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf7f000 - 0xbdf82fff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf83000 - 0xbdf84fff]
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Read] Request device [02:00.0] fault addr fffff000 [fault reason 06] PTE Read access is not set
hpsa 0000:02:00.0: controller message 03:00 timed out
hpsa 0000:02:00.0: no-op failed; re-trying
After some debugging, we found that the fault addr is from DMA initiated at
the driver probe stage after reset(not in-flight DMA), and the corresponding
pte entry value is correct, the fault is likely due to the old iommu caches
of the in-flight DMA before it.
Thus we need to flush the old cache after context mapping is setup for the
device, where the device is supposed to finish reset at its driver probe
stage and no in-flight DMA exists hereafter.
I'm not sure if the hardware is responsible for invalidating all the related
caches allocated in the iommu hardware before, but seems not the case for hpsa,
actually many device drivers have problems in properly resetting the hardware.
Anyway flushing (again) by software in kdump kernel when the device gets context
mapped which is a quite infrequent operation does little harm.
With this patch, the problematic machine can survive the kdump tests.
CC: Myron Stowe <myron.stowe@gmail.com>
CC: Joseph Szczypek <jszczype@redhat.com>
CC: Don Brace <don.brace@microsemi.com>
CC: Baoquan He <bhe@redhat.com>
CC: Dave Young <dyoung@redhat.com>
Fixes: 091d42e43d21 ("iommu/vt-d: Copy translation tables from old kernel")
Fixes: dbcd861f252d ("iommu/vt-d: Do not re-use domain-ids from the old kernel")
Fixes: cf484d0e6939 ("iommu/vt-d: Mark copied context entries")
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65ca7f5f7d1cdde6c25172fe6107cd16902f826f upstream.
Different encodings are used to represent supported PASID bits
and number of PASID table entries.
The current code assigns ecap_pss directly to extended context
table entry PTS which is wrong and could result in writing
non-zero bits to the reserved fields. IOMMU fault reason
11 will be reported when reserved bits are nonzero.
This patch converts ecap_pss to extend context entry pts encoding
based on VT-d spec. Chapter 9.4 as follows:
- number of PASID bits = ecap_pss + 1
- number of PASID table entries = 2^(pts + 5)
Software assigned limit of pasid_max value is also respected to
match the allocation limitation of PASID table.
cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Tested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Fixes: 2f26e0a9c9860 ('iommu/vt-d: Add basic SVM PASID support')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 432abf68a79332282329286d190e21fe3ac02a31 upstream.
The generic command buffer entry is 128 bits (16 bytes), so the offset
of tail and head pointer should be 16 bytes aligned and increased with
0x10 per command.
When cmd buf is full, head = (tail + 0x10) % CMD_BUFFER_SIZE.
So when left space of cmd buf should be able to store only two
command, we should be issued one COMPLETE_WAIT additionally to wait
all older commands completed. Then the left space should be increased
after IOMMU fetching from cmd buf.
So left check value should be left <= 0x20 (two commands).
Signed-off-by: Huang Rui <ray.huang@amd.com>
Fixes: ac0ea6e92b222 ('x86/amd-iommu: Improve handling of full command buffer')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24c790fbf5d8f54c8c82979db11edea8855b74bf upstream.
We should set "ret" to -EINVAL if iommu_group_get() fails.
Fixes: 55c99a4dc50f ("iommu/amd: Use iommu_attach_group()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2a33c34ddff22ee208d80abdd12b88a98d6cb60 upstream.
The RZ/A1 is different than the other Renesas SOCs because the MSTP
registers are 8-bit instead of 32-bit and if you try writing values as
32-bit nothing happens...meaning this driver never worked for r7s72100.
Fixes: b6face404f38 ("ARM: shmobile: r7s72100: add essential clock nodes to dtsi")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bae203d58b7dce89664071b3fafe20cedaa3e4f6 upstream.
Function mx31_clocks_init() is called during clock intialization on
legacy boards with reference clock frequency passed as its input
argument, this can be verified by examination of the function
declaration found in arch/arm/mach-imx/common.h and actual function
users which include that header file.
Inside CCF driver the function ignores its input argument, by chance
the used value in the function body is the same as input arguments on
side of all callers.
Fixes: d9388c843237 ("clk: imx31: Do not call mxc_timer_init twice when booting with DT")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f6f9302b819ca352cfd4f42c18ec08d521f9cae upstream.
The audio module clocks are supposed to be set according to the sample
rate of the audio stream. The audio PLL provides the clock signal for
these module clocks, and only it is freely tunable.
Set CLK_SET_RATE_PARENT for the audio module clocks so their users can
properly tune the clock rate.
Fixes: 0577e4853bfb ("clk: sunxi-ng: Add H3 clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 937ff9ded8b6ebe8963ade55bdd77a61ded88075 upstream.
The audio module clocks are supposed to be set according to the sample
rate of the audio stream. The audio PLL provides the clock signal for
these module clocks, and only it is freely tunable.
Set CLK_SET_RATE_PARENT for the audio module clocks so their users can
properly tune the clock rate.
Fixes: 5690879d93e8 ("clk: sunxi-ng: Add A23 CCU")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20979202ee6e4c68dab7bcf408787225a656d18e upstream.
Fix bug https://bugzilla.kernel.org/show_bug.cgi?id=188561. Function
wm831x_clkout_is_prepared() returns "true" when it fails to read
CLOCK_CONTROL_1. "true" means the device is already prepared. So
return "true" on the read failure seems improper.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Fixes: f05259a6ffa4 ("clk: wm831x: Add initial WM831x clock driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbf2e548ca8ad4bb274d014e9a70bd841d29948e upstream.
The clocks on these boards run at 25 MHz, not 19.2 and 27 like
other platforms. Unfortunately I copy/pasted from other similar
SoCs but forgot this one is different. Fix it.
Fixes: a085f877a882 ("clk: qcom: Move cxo/pxo/xo into dt files")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 792f497b22afd0563b94dd8fa129a05f762a2c25 upstream.
We should unlock before returning on this error path.
Fixes: 3a762dbd5347 ('[media] Input: synaptics-rmi4 - add support for F54 diagnostics')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9572fdd13e299cfba03abbfd2786c84ac055249 upstream.
Since commit commit eb1c8f4325d5 ("hwmon: (lm90) Convert to use new hwmon
registration API") the temp1_max_alarm and temp1_crit_alarm attributes are
mapped to the same alarm bit. Fix the typo.
Fixes: eb1c8f4325d5 ("hwmon: (lm90) Convert to use new hwmon registration API")
Signed-off-by: Micehael Walle <michael@walle.cc>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4fccd4a1e8944033bcd7693ea4e8fb478cd2059a upstream.
Fix overflows seen when writing into fan speed limit attributes.
Also fix crash due to division by zero, seen when certain very
large values (such as 2147483648, or 0x80000000) are written
into fan speed limit attributes.
Fixes: 594fbe713bf60 ("Add support for GMT G762/G763 PWM fan controllers")
Cc: Arnaud Ebalard <arno@natisbad.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0d04e9112ad59d73f23f3b0f6726c5e798dfcbf upstream.
Fix overflows seen when writing voltage and temperature limit attributes.
The value passed to DIV_ROUND_CLOSEST() needs to be clamped, and the
value parameter passed to nct7802_write_fan_min() is an unsigned long.
Also, writing values larger than 2700000 into a fan limit attribute results
in writing 0 into the chip's limit registers. The exact behavior when
writing this value is unspecified. For consistency, report a limit of
1350000 if the chip register reads 0. This may be wrong, and the chip
behavior should be verified with the actual chip, but it is better than
reporting a value of 0 (which, when written, results in writing a value
of 0x1fff into the chip register).
Fixes: 3434f3783580 ("hwmon: Driver for Nuvoton NCT7802Y")
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e36ce99ee0815d7919a7b589bfb66f3de50b6bc7 upstream.
Module test reports:
temp1_max: Suspected overflow: [160000 vs. 0]
temp1_min: Suspected overflow: [160000 vs. 0]
This is seen because the values passed when writing temperature limits
are unbound.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Fixes: 6099469805c2 ("hwmon: Support for Dallas Semiconductor DS620")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4538bfbf2d9f1fc48c07ac0cc0ee58716fe7fe96 upstream.
Converts the unsigned temperature values from the i2c read
to be sign extended as defined in the datasheet so that
negative temperatures are properly read.
Fixes: 28e6274d8fa67 ("hwmon: (amc6821) Avoid forward declaration")
Signed-off-by: Jared Bents <jared.bents@rockwellcollins.com>
Signed-off-by: Matt Weber <matthew.weber@rockwellcollins.com>
[groeck: Dropped unnecessary continuation line]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13edb767aa609b6efb7c0c2b57fbd72a6ded0eed upstream.
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/hwmon/scpi-hwmon.ko | grep alias
$
After this patch:
$ modinfo drivers/hwmon/scpi-hwmon.ko | grep alias
alias: of:N*T*Carm,scpi-sensorsC*
alias: of:N*T*Carm,scpi-sensors
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Fixes: ea98b29a05e9c ("hwmon: Support sensors exported via ARM SCP interface")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a608a9d52fa4168efd478d684039ed545a69dbcd upstream.
All LED-setting functions in fujitsu-laptop are currently assigned to
the brightness_set callback, which is incorrect because they can sleep
(due to their use of call_fext_func(), which in turn issues ACPI calls)
and the documentation (in include/linux/leds.h) clearly states they must
not. Assign them to brightness_set_blocking instead and change them to
match the expected function prototype.
This change makes it possible to use Fujitsu-specific LEDs with "heavy"
triggers, like disk-activity or phy0rx.
Fixes: 3a407086090b ("fujitsu-laptop: Add BL power, LED control and radio state information")
Fixes: 4f62568c1fcf ("fujitsu-laptop: Support radio LED")
Fixes: d6b88f64b0d4 ("fujitsu-laptop: Add support for eco LED")
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3df8d9208569ef0b2313e516566222d745f3b94b upstream.
A typo (or mis-merge?) resulted in leaf 6 only being probed if
cpuid_level >= 7.
Fixes: 2ccd71f1b278 ("x86/cpufeature: Move some of the scattered feature bits to x86_capability")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Link: http://lkml.kernel.org/r/6ea30c0e9daec21e488b54761881a6dfcf3e04d0.1481825597.git.luto@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a01aa6c9f40fe03c82032e7f8b3bcf1e6c93ac0e upstream.
As userspace knows nothing about kernel config, thus #ifdefs
around ABI prctl constants makes them invisible to userspace.
Let it be clean'n'simple: remove #ifdefs.
If kernel has CONFIG_CHECKPOINT_RESTORE disabled, sys_prctl()
will return -EINVAL for those prctls.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Dmitry Safonov <dsafonov@virtuozzo.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: 0x7f454c46@gmail.com
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Cc: oleg@redhat.com
Fixes: 2eefd8789698 ("x86/arch_prctl/vdso: Add ARCH_MAP_VDSO_*")
Link: http://lkml.kernel.org/r/20161027141516.28447-2-dsafonov@virtuozzo.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f847dd31736f1284538e54f46cf10e63929eb7f upstream.
The slp_s0_residency_usec debugfs file currently uses
DEFINE_DEBUGFS_ATTRIBUTE(), but that macro cannot really be used to
define files outside of the debugfs code, as it has no reference to
the get/set functions if CONFIG_DEBUG_FS is not defined:
drivers/platform/x86/intel_pmc_core.c:80:12: error: ‘pmc_core_dev_state_get’ defined but not used [-Werror=unused-function]
This fixes the macro to always contain the reference, and instead rely
on the stubbed-out debugfs_create_file to not actually refer to
its arguments so the compiler can still drop the reference.
This works because the attribute definition is always 'static',
and the dead-code removal silently drops all static symbols
that are not used.
Fixes: c64688081490 ("debugfs: add support for self-protecting attribute file fops")
Fixes: df2294fb6428 ("intel_pmc_core: Convert to DEFINE_DEBUGFS_ATTRIBUTE")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[nicstange@gmail.com: Add dummy implementations of debugfs_attr_read() and
debugfs_attr_write() in order to protect against possibly broken dead
code elimination and to improve readability.
Correct CONFIG_DEBUGFS_FS -> CONFIG_DEBUG_FS typo in changelog.]
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc4725d9029e2c8205fbaf1105e193d1c4e463bb upstream.
The intention was to enable the checks if debugging is enabled, not
disabled.
Fixes: f793d1e51705b276 ("clk: shmobile: Add new CPG/MSSR driver core")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 328cf6927bb72cadefddebbc9a23c793108147a2 upstream.
If CONFIG_ETRAX_AXISFLASHMAP is not configured, the flash rescue image
object file is empty. With recent versions of binutils, this results
in the following build error.
cris-linux-objcopy: error:
the input file 'arch/cris/boot/rescue/rescue.o' has no sections
This is seen, for example, when trying to build cris:allnoconfig
with recently generated toolchains.
Since it does not make sense to build a flash rescue image if there is
no flash, only build it if CONFIG_ETRAX_AXISFLASHMAP is enabled.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 66ab3a74c5ce ("CRIS: Merge machine dependent boot/compressed ..")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31b239824ece321c09bdb8e61e1d14814eaba38b upstream.
The word "background" contains 10 characters so the third argument of
strncmp() need to be 10 in order to match this prefix correctly.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Fixes: 855aed1220d2 ("ath10k: add spectral scan feature")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcf7cf1551cae54e747a771f5808240f2a37708f upstream.
This partially reverts 'commit 2cdce425aa33
("ath10k: Fix broken NULL func data frame status for 10.4")'
Unfortunately this breaks sending NULL func and the existing
issue of obtaining proper tx status for NULL function will be
fixed. Also update the comments for feature flag added to be
useless and not working
Fixes: 2cdce425aa33 "ath10k: Fix broken NULL func data frame status for
10.4"
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fa436b3a2a7009c11a3bc03fe0ff4c26e80fd87 upstream.
NL80211_ATTR_MAC was used to set both the specific BSSID to be scanned
and the random MAC address to be used when privacy is enabled. When both
the features are enabled, both the BSSID and the local MAC address were
getting same value causing Probe Request frames to go with unintended
DA. Hence, this has been fixed by using a different NL80211_ATTR_BSSID
attribute to set the specific BSSID (which was the more recent addition
in cfg80211) for a scan.
Backwards compatibility with old userspace software is maintained to
some extent by allowing NL80211_ATTR_MAC to be used to set the specific
BSSID when scanning without enabling random MAC address use.
Scanning with random source MAC address was introduced by commit
ad2b26abc157 ("cfg80211: allow drivers to support random MAC addresses
for scan") and the issue was introduced with the addition of the second
user for the same attribute in commit 818965d39177 ("cfg80211: Allow a
scan request for a specific BSSID").
Fixes: 818965d39177 ("cfg80211: Allow a scan request for a specific BSSID")
Signed-off-by: Vamsi Krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
