IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The recently added driver uses the firmware loader mechanism but causes
a link failure when that is in a loadable module while thp7312 itself
is built-in:
arm-linux-gnueabi-ld: drivers/media/i2c/thp7312.o: in function `thp7312_probe':
thp7312.c:(.text+0x4164): undefined reference to `firmware_upload_register'
Select the required Kconfig symbol. Note that the driver specifically
needs the firmware upload interface that is controlled by CONFIG_FW_UPLOAD,
but there is no link failure when that is disabled because the interfaces
are stubbed out here.
Link: https://lore.kernel.org/linux-media/20240103155811.4092035-1-arnd@kernel.org
Fixes: 7a52ab415b43 ("media: i2c: Add driver for THine THP7312")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
With clang-16, building without COMMON_CLK triggers a range check on
udelay() because of a constant division-by-zero calculation:
ld.lld: error: undefined symbol: __bad_udelay
>>> referenced by mt9m114.c
>>> drivers/media/i2c/mt9m114.o:(mt9m114_power_on) in archive vmlinux.a
In this configuration, the driver already fails to probe, before
this function gets called, so it's enough to suppress the assertion.
Do this by using fsleep(), which turns long delays into sleep() calls
in place of the link failure.
This is probably a good idea regardless to avoid overly long dynamic
udelay() calls on a slow clock.
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Fixes: 24d756e914fc ("media: i2c: Add driver for onsemi MT9M114 camera sensor")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Rename min_buffers_needed into min_queued_buffers and update
the documentation about it.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: Drop the change where min_queued_buffers + 1 buffers would be]
[hverkuil: allocated. Now this patch only renames this field instead of making]
[hverkuil: a functional change as well.]
[hverkuil: Renamed 3 remaining min_buffers_needed occurrences.]
Use the newly added storage for frame interval in the subdev state to
simplify the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The routing ioctls documentation incorrectly describes the 'which'
field, due to a bad copy & paste. Fix it.
Fixes: ea73eda50813 ("media: Documentation: Add GS_ROUTING documentation")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Multiple subdev ioctls that take a 'which' field do not document the
error returned when the field has an invalid value. Expand the
documentation to fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Invalid values for the 'which' field of structures passed to multiple
subdev ioctls result in an EINVAL error being returned. The
documentation of the corresponding ioctls indicates this with sentences
such as the following:
the ``which`` field references a non-existing format
This is confusing. Clarify the documentation.
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Subdev states store all standard pad configuration data, except for
frame intervals. Fix it by adding interval fields in the
v4l2_subdev_pad_config and v4l2_subdev_stream_config structures, with
corresponding accessor functions and a helper function to implement the
.get_frame_interval() operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Due to a historical mishap, the v4l2_subdev_frame_interval structure
is the only part of the V4L2 subdev userspace API that doesn't contain a
'which' field. This prevents trying frame intervals using the subdev
'TRY' state mechanism.
Adding a 'which' field is simple as the structure has 8 reserved fields.
This would however break userspace as the field is currently set to 0,
corresponding to V4L2_SUBDEV_FORMAT_TRY, while the corresponding ioctls
currently operate on the 'ACTIVE' state. We thus need to add a new
subdev client cap, V4L2_SUBDEV_CLIENT_CAP_INTERVAL_USES_WHICH, to
indicate that userspace is aware of this new field.
All drivers that implement the subdev .get_frame_interval() and
.set_frame_interval() operations are updated to return -EINVAL when
operating on the TRY state, preserving the current behaviour.
While at it, fix a bad copy&paste in the documentation of the struct
v4l2_subdev_frame_interval_enum 'which' field.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> # for imx-media
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for tegra-video
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .[gs]_frame_interval are video operations, but they operate
on pads (and even on streams). Not only is this confusing, it causes
practical issues for drivers as the operations don't receive a subdev
state pointer, requiring manual state handling.
To improve the situation, turn the operations into pad operations, and
extend them to receive a state pointer like other pad operations.
While at it, rename the operations to .[gs]et_frame_interval at the same
time to match the naming scheme of other pad operations. This isn't
strictly necessary, but given that all drivers using those operations
need to be modified, handling the rename separately would generate more
churn for very little gain (if at all).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> # for imx-media
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for tegra-video
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev state locking macros and macros to get the active state are
currently behind CONFIG_MEDIA_CONTROLLER. This makes sense, as there can
be no subdev state without MC.
However, we have code paths common to MC and non-MC cases which call
subdev operations that have subdev state as a parameter. In the non-MC
case the state parameter would always be NULL.
Thus it makes sense to allow, e.g.:
v4l2_subdev_call_state_active(sd, pad, get_fmt, fmt)
which for non-MC case would call the subdev passing NULL as the state.
This currently fails:
https://lore.kernel.org/oe-kbuild-all/202312061101.PLrz5NnJ-lkp@intel.com/
Fix the issue by moving the related macros to be outside
CONFIG_MEDIA_CONTROLLER. The v4l2_subdev_lock_state() and
v4l2_subdev_unlock_state() macros will crash if given NULL as the state,
but the other macros behave correctly even when there's no active state,
and they will only call the lock/unlock macros if there is a state.
An alternative fix would be to make another version of
v4l2_subdev_call_state_try() with ifdefs, which would not use any state
macros and would always pass NULL as the state. But having two version
of a macro/function is always more confusing than having just one, so I
went this way.
So, this fixes the v4l2_subdev_call_state_active() macro. But we also
have v4l2_subdev_call_state_try(). It would be possible to fix that
macro by additionally creating "no-op" variants of the state alloc and
free functions. However, v4l2_subdev_call_state_try() is only used by a
single driver (stm32-dcmi), which selects MC, and the macro is supposed
to be removed as soon as the users have been converted away from the
macro. Thus I have not touched the state alloc/free functions, and I
think it makes sense to keep alloc/free functions available only if
there's actually something that can be allocated or freed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/r/20231208-v4l2-state-mc-fix-v1-1-a0c8162557c6@ideasonboard.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add allocation of DPB buffers based on MFC requirement so,
codec buffers allocations has been moved after state
MFCINST_HEAD_PRODUCED. It is taken care that codec buffer allocation
is performed in process context from userspace IOCTL call.
Cc: linux-fsd@tesla.com
Signed-off-by: Smitha T Murthy <smithatmurthy@gmail.com>
Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
In MFCv12, some section of firmware gets updated at each MFC run.
Hence we need to reload original firmware for each run at the start.
Cc: linux-fsd@tesla.com
Signed-off-by: Smitha T Murthy <smithatmurthy@gmail.com>
Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Context bit is set for hardware execution if there is a buffer in
source and destination queue before calling try_run in the
init_buffers function. Now there will be a new context created and
hardware will be invoked for the buffer queued instead of waiting for
another buffer to be queued from userspace to set this context bit for
hw execution.
Cc: linux-fsd@tesla.com
Signed-off-by: Smitha T Murthy <smithatmurthy@gmail.com>
Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
MFC driver had restriction on max resolution of 1080p, updated it for
UHD. Added corresponding support to set recommended profile and level
for H264 in UHD scenario.
Cc: linux-fsd@tesla.com
Signed-off-by: Smitha T Murthy <smithatmurthy@gmail.com>
Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
In MFCv12, the rc configs are changed with support for CBR loose,
CBR tight and Variable Bitrate (VBR) added.
Cc: linux-fsd@tesla.com
Signed-off-by: Smitha T Murthy <smithatmurthy@gmail.com>
Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
YV12 and I420 format (3-plane) support is added. Stride information is
added to all formats and planes since it is necessary for YV12/I420
which are different from width.
Cc: linux-fsd@tesla.com
Signed-off-by: Smitha T Murthy <smithatmurthy@gmail.com>
Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add support for MFCv12, with a new register file and necessary hw
control, decoder, encoder and structural changes. Add luma dbp, chroma
dpb and mv sizes for each codec as per the UM for MFCv12, along with
appropriate alignment.
Cc: linux-fsd@tesla.com
Signed-off-by: Smitha T Murthy <smithatmurthy@gmail.com>
Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Renames macro IS_MFCV10 to IS_MFCV10_PLUS so that the MFCv10 code can
be resued for MFCv12 support. Since some part of MFCv10 specific code
holds good for MFCv12 also.
Cc: linux-fsd@tesla.com
Signed-off-by: Smitha T Murthy <smithatmurthy@gmail.com>
Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add a driver for the OmniVision OV64A40 image sensor.
Co-developed-by: Lee Jackson <lee.jackson@arducam.com>
Signed-off-by: Lee Jackson <lee.jackson@arducam.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add bindings for OmniVision OV64A40.
Co-developed-by: Lee Jackson <lee.jackson@arducam.com>
Signed-off-by: Lee Jackson <lee.jackson@arducam.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
In addition to the existing 2592x1940 12-bit mode, introduce support
for 2592x1940 10-bit mode.
Following are the register set which control the 10/12 bit mode setting:
MDBIT 0x319d
ADBIT 0x3050
ADBIT1 0x341c
0x341d
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The V4L2_CID_HBLANK control is marked as readonly and can only be a
single value.
Set the minimum and maximum value to match the mode value.
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Support reporting of the Sensor Native and Active pixel array areas
through the Selection API.
The implementation reports a single target crop only for the mode that
is presently exposed by the driver.
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Provide support for enabling and disabling regulator supplies to control
power to the camera sensor.
While updating the power on function, document that a sleep is
represented as 'T4' in the datasheet power on sequence.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The existing imx335_parse_hw_config function has two paths
that can be taken without reporting to the user the reason
for failing to accept the hardware configuration.
Extend the error reporting paths to identify failures when
probing the device.
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The use of \n as a line ending throughout the driver is inconsistent.
While it is possible for logging messages to automatically have newlines
added by the kernel printk mechanisms, this is specifically to support
continued lines with PR_CONT and the lack of a new line character
indicates that the text is a fragment of a continuation line.
As each of these lines are whole and not fragments, explicitly define the
newline for consistency.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add the bindings for the supply references used on the IMX335.
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Set effective and active sensor pixel sizes as shown in product
brief[1].
[1]: https://www.mouser.com/datasheet/2/897/ProductBrief_IMX214_20150428-1289331.pdf
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Obtain rotation and orientation information from system firmware and
register the appropriate controls. While at it, update number of
pre-allocated control slots.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Code refinement.
While at it, don't destroy the mutex not initialized yet if the controls
are initialized incorrectly.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Code refinement, no functional changes.
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
[Sakari Ailus: The control handler remains in the context struct still.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Introduce new driver for GalaxyCore GC0308, which is a cheap
640x480 with an on-chip ISP sensor sold since 2010. Data is
provided via parallel bus.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
[Sakari Ailus: Changed MAINTAINERS to match GC2145 entry.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
"gc" prefixed i2c media drivers are most likely GalaxyCore camera
sensor drivers, so add it to the list.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add DT binding for GalaxyCore GC0308 camera sensor.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The data lanes and link frequency were set to match existing Linux driver
limitations, however bindings should be independent of chosen Linux
driver support.
Decouple these properties from the driver to match what is actually
supported by the hardware.
This also fixes DTS example:
ov8856.example.dtb: camera@10: port:endpoint:link-frequencies:0: [360000000] is too short
Fixes: 066a94e28a23 ("media: dt-bindings: media: Use graph and video-interfaces schemas")
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
LP-11 and LP-111 are CSI-2 bus states, not modes. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
BT.601 is not actually a bus specification, leaving parallel bus without a
specification to refer to. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Graciously handle an uninitialised (but still zeroed) sub-device in
v4l2_subdev_cleanup(). The list_empty() check there is unnecessary, too,
so replace that by cheking whether the lists's next field is NULL.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The only known devices that use an ov2740 sensor in combination with
the ipu-bridge code are various Lenovo ThinkPad models, which all
need the link-frequency to be 180 MHz for things to work properly.
The ov2740 driver used to only support 360 MHz link-frequency,
which is why the ipu-bridge entry used 360 MHz, but now the
ov2740 driver has been extended to also support 180 MHz.
The ov2740 is actually used with 360 MHz link-frequency on Chromebooks.
On Chromebooks the camera/sensor fwnode graph is part of the ACPI tables.
The ipu-bridge code is used to dynamically generate the graph when it is
missing, so it is not used on Chromebooks and the ov2740 will keep using
360 MHz link-frequency there as before.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Split the resetting of the sensor out of the link_freq_config reg_list
and add a delay after this.
This hopefully fixes the stream sometimes not starting, this was
taken from the ov2740 sensor driver in the out of tree IPU6 driver:
https://github.com/intel/ipu6-drivers/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
On various Lenovo Thinkpad models with an ov2740 sensor the 360 MHz
link frequency is not supported.
Add support for 180 MHz link frequency, even though this has half the
pixel clock, this supports the same framerate by using half the VTS value
(significantly reducing the amount of empty lines send during vblank).
Normally if there are multiple link-frequencies then the sensor driver
choses the lowest link-frequency still usable for the chosen resolution.
In this case the board supports only 1 link-frequency. Which frequency
is supported is checked in ov2740_check_hwcfg() and then a different
set of supported_modes (using only the supported link-freq) is selected.
The register settings for this were taken from the ov2740 sensor driver
in the out of tree IPU6 driver:
https://github.com/intel/ipu6-drivers/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Alloc ov2740_data and set up the drvdata pointer before calling
ov2740_check_hwcfg().
This is a preparation patch to allow ov2740_check_hwcfg()
to store some of the parsed data in the ov2740 struct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
HTS must be more then width, so the 1080 value clearly is wrong,
this is then corrected with some weird math dividing clocks in
to_pixels_per_line() which results in the hts getting multiplied by 2,
resulting in 2160.
Instead just directly set hts to the correct value of 2160 and
drop to_pixels_per_line().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Make ov2740_check_hwcfg() report an error on failure in all error paths,
so that it is always clear why the probe() failed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
If the bridge has not yet setup the fwnode-graph then
the fwnode_property_read_u32("clock-frequency") call will fail.
Move the fwnode_graph_get_next_endpoint() call to above reading
the clock-frequency.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
On some ACPI platforms, such as Chromebooks the ACPI methods to
change the power-state (_PS0 and _PS3) fully take care of powering
on/off the sensor.
On other ACPI platforms, such as e.g. various ThinkPad models with
IPU6 + ov2740 sensor, the sensor driver must control the reset GPIO
and the sensor's clock itself.
Add support for having the driver control an optional clock.
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
On some ACPI platforms, such as Chromebooks the ACPI methods to
change the power-state (_PS0 and _PS3) fully take care of powering
on/off the sensor.
On other ACPI platforms, such as e.g. various ThinkPad models with
IPU6 + ov2740 sensor, the sensor driver must control the reset GPIO
and the sensor's clock itself.
Add support for having the driver control an optional reset GPIO.
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
