IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
For recent ISPs, software during CS_UNDERRUN handling must
determine if the two residuals, firmware-calculated and FCP_RSP,
are different to recognize if a frame has been dropped. Update
the driver to catch this condition, and clear the
SS_RESIDUAL_UNDER and lscsi_status bits. This logic is
consistent with what earlier firmwares did by explicitly
cracking open the FCP_RSP statuses and clearing
SS_RESIDUAL_UNDER.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Recent ISPs need only the single MMIO BAR to manipulate HW
registers. Unfortunately, ISP21xx, ISP22xx, ISP23xx, and ISP63xx
type cards still require the I/O mapped region to manipulate the
FLASH via the two HW flash-registers (flash_address and
flash_data).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original implementation would not use the burst-write mechanisms
for requests equal to OPTROM_BURST_DWORDS transfer dwords.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since both NVRAM and VPD regions of the flash reside on unaligned
sector boundaries, during update, the driver must perform a
read-modify-write operation to the composite NVRAM/VPD region.
This affects ISP25xx type boards only.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As the intermixing may cause issues where HCCR bits could be
cleared inappropriately during MSI/MSI-X interrupt handling.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This function just printed a message to the user; move the print to its
only caller, and turn it into an starget_printk.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This structure is accessed by the device; the fewer Linux things in it,
the better. Using the pci_dev pointer from the hostdata requires a lot
of changes:
- Pass Scsi_Host to a lot of routines which currently take a sym_hcb.
- Set the Scsi_Host as the pci drvdata (instead of the sym_hcb)
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make sym_interrupt return an irqreturn_t instead of void, and take a
Scsi_Host instead of a sym_hcb. Pass the Scsi_Host to the interrupt
handler instead of the sym_hcb. Rename the host_data to sym_data.
Keep a pci_dev pointer in the sym_data. Rename the Scsi_Host from
instance to shost.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
These macros aren't needed any more. They used to be used for SPARC.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If we have a scsi_cmnd, it gives the user more information than the
sym_name, and maybe the target.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
By introducing the use_dac(), set_dac() and DMA_DAC_MASK macros, we can
eliminate a lot of ifdefs from the code. We now rely on the compiler to
optimise away a few things that we'd formerly relied on the preprocessor
to do. This makes sym_setup_bus_dma_mask() small enough to inline into
its only caller.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
With sysfs making these options tunable at runtime, there's no
justification for keeping this horrendously complex specification
string around.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
These struct elements record info that is never needed
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Following the same path as ->revision_id, remove ->device_id
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Auke missed the sym2 driver in his initial sweep.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds the PCI error recovery callbacks to the Symbios SCSI device
driver. It includes support for First Failure Data Capture.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Assorted changes to initial patches, including returning IRQ_NONE from the
interrupt handler if the device is offline and re-using the eh_done completion
in the scsi error handler.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Instead of telling the reset routine that the command completed from
sym_eh_done, do it from sym_xpt_done. The 'to_do' element of the ucmd
is redundant -- it serves only to tell whether eh_done is valid or not,
and we can tell this by checking to see if it's NULL.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Interrupts can't be re-entered, so it's sufficient to call spin_lock, not
spin_lock_irqsave().
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The midlayer won't scan the host ID, so we don't need to check.
This is the only caller of sym_xpt_done2, so remove that too.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Before all commands used sg, data_mapping and data_mapped were used to
distinguish whether the command had used map_single or map_sg. Now all
commands are sg, so we can delete data_mapping, data_mapped and the
wrapper functions __unmap_scsi_data, __map_scsi_sg_data, unmap_scsi_data
and map_scsi_sg_data.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Don't cache a private copy of the interrupt number
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Prevent DMA transfers from crossing the 16MB limit for early 53c896 chips.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
i think there is wasted space in allocated pages for request and
response rings. The allocations are made with REQUEST_ENTRY_CNT + 1
and RESPONSE_ENTRY_CNT + 1, but they are set with 256 and 16.
So we got more pages, which we dont use very much so eliminate them.
Signed-off-by: Johannes Dickgreber <tanzy@gmx.de>
Acked-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If a prefix is selected for flex, we should be using it everywhere.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The aic7xxx driver already contains fragments for suspend/resume
support. So we only need to update them to the current interface
and have full PCI suspend/resume.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Tested-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A failure here wouldn't currently free the irq; go to the irq free
path instead.
Signed-off-by: Johannes Dickgreber <tanzy@gmx.de>
Acked-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes the following build warnings:
WARNING: vmlinux.o(.text+0xbcffdb): Section mismatch: reference to .init.text.20:gdth_search_drives (between 'gdth_pci_probe_one' and 'gdth_start_timeout')
WARNING: vmlinux.o(.text+0xbd0102): Section mismatch: reference to .init.text.20:gdth_enable_int (between 'gdth_pci_probe_one' and 'gdth_start_timeout')
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Commit bbfbbbc118 accidentally reversed
the logic of this NULL check.
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
drivers/scsi/qla2xxx/qla_sup.c: In function 'qla24xx_write_flash_data':
drivers/scsi/qla2xxx/qla_sup.c:655: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'dma_addr_t'
drivers/scsi/qla2xxx/qla_sup.c: In function 'qla25xx_read_optrom_data':
drivers/scsi/qla2xxx/qla_sup.c:1853: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'dma_addr_t'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes a typo introduced by
commit bbfbbbc118.
It wasn't a compile error since CONFIG_LPFC_DEBUG_FS is not (yet?)
available as an option.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix IRQ reporting - just assign the ->pci_dev pointer earlier and use the
pci_dev irq field rather than keeping a private one
Init the spinlock as it works better on SMP that way
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The newer firmware may return more than 96 bytes of sense data when it
does autosense. Truncate this to the size of the SCSI layer sense
buffer to avoid an overrun.
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
if shost->supported mode is zero (i.e. MODE_UNKNOWN) show it as
initiator (it's obviously an unconverted driver that won't do target).
Acked-by: FUJITA Tomonori <tomof@acm.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Spotted by Paul Jackson <pj@sgi.com>
The error handler rework moved the scatterlist into a globally exposed
structure in scsi_eh.h; unfortunately, the scatterlist include needs
to move from scsi_error.c to scsi_eh.h to allow this to compile
universally.
Acked-by: Paul Jackson <pj@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This code has been slowly rotting for about eight years. It's currently
impeding a few SCSI cleanups, and nobody seems to have hardware to test
it any more. I talked to Dave Miller about it, and he agrees we can
delete it. If anyone wants a software FC stack in future, they can
retrieve this driver from git.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
arch/ia64/kernel/machine_kexec.c: In function `arch_crash_save_vmcoreinfo':
arch/ia64/kernel/machine_kexec.c:131: error: `pgdat_list' undeclared (first use in this function)
arch/ia64/kernel/machine_kexec.c:131: error: (Each undeclared identifier is reported only once
arch/ia64/kernel/machine_kexec.c:131: error: for each function it appears in.)
arch/ia64/kernel/machine_kexec.c:134: error: `node_memblk' undeclared (first use in this function)
arch/ia64/kernel/machine_kexec.c:135: error: `NR_NODE_MEMBLKS' undeclared (first use in this function)
arch/ia64/kernel/machine_kexec.c:136: error: invalid application of `sizeof' to incomplete type `node_memblk_s'
arch/ia64/kernel/machine_kexec.c:137: error: dereferencing pointer to incomplete type
arch/ia64/kernel/machine_kexec.c:138: error: dereferencing pointer to incomplete type
make[1]: *** [arch/ia64/kernel/machine_kexec.o] Error 1
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
net: libertas sdio driver
mmc: at91_mci: cleanup: use MCI_ERRORS
mmc: possible leak in mmc_read_ext_csd
make clean failed to delete a few files in
x86/kernel. This is because kbuild does not
see the correct/full kernel/Makefile.
As a workaround until the Makefiles are merged specify
the files to be deleted in the common Makefile.
Reported by Mike Galbraith <efault@gmx.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Mike Galbraith <efault@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
A sysctl method was added to enable and disable debugging levels. After
further review, it was decided that there are better approaches to doing this
and the sysctl methodology isn't really desirable. This patch removes the
sysctl code from 9p.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
A small MMC driver cleanup.
Use the defined AT91_MCI_ERRORS in at91_mci_completed_command() instead
of specifying all the error bits individually.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The exception path associated with an invalid ext_csd_struct returns
without freeing ext_csd.
Coverity CID 1909.
Signed-off-by: Florin Malita
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch moves transport dynamic registration and matching to the net
module to prevent a bad Kconfig dependency between the net and fs 9p modules.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Loose mode in 9p utilizes the page cache without respecting coherency with
the server. Any writes previously invaldiated the entire mapping for a file.
This patch softens the behavior to only invalidate the region of the actual
write.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
