IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The DEVICE_BUSY_TIMEOUT value is described in the Reference Manual as:
| Timeout waiting for NAND Ready/Busy or ATA IRQ. Used in WAIT_FOR_READY
| mode. This value is the number of GPMI_CLK cycles multiplied by 4096.
So instead of multiplying the value in cycles with 4096, we have to
divide it by that value. Use DIV_ROUND_UP to make sure we are on the
safe side, especially when the calculated value in cycles is smaller
than 4096 as typically the case.
This bug likely never triggered because any timeout != 0 usually will
do. In my case the busy timeout in cycles was originally calculated as
2408, which multiplied with 4096 is 0x968000. The lower 16 bits were
taken for the 16 bit wide register field, so the register value was
0x8000. With 2970bf5a32f0 ("mtd: rawnand: gpmi: fix controller timings
setting") however the value in cycles became 2384, which multiplied
with 4096 is 0x950000. The lower 16 bit are 0x0 now resulting in an
intermediate timeout when reading from NAND.
Fixes: b1206122069aa ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation")
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220614083138.3455683-1-s.hauer@pengutronix.de
This reverts commit 3380557fc7e28d9bce7607e16d98f123d36da4ca.
It turned out this "4-byte" ID might have been an honest mistake.
Regrettably, the chip Andreas has might be a counterfeit or is
damaged in some other way and shouldn't have ended up in a router.
Andreas reported his chip is returning just four bytes:
"98 f1 80 15 00 00 00 00".
However, according to Kioxia/Toshiba's datasheet, there should
have been at least another byte that would have contained the
correct OOB size that Andreas needed.
Miquel and Andreas are both favoring reverting the patch over
further, possibly hacky modifications:
"[Reverting] is the safest option here. Apart from this device, we
do not know how many devices have these damaged/counterfeit chips.
If it is just a couple and only on Fritzboxes, as suggested in the
Github issue the patch could be carried through OpenWrt[...]"
Thanks to several users on the openwrt forum and github issue,
who stayed along for the ride:
- Peter-vdL for reporting the issue and testing patches.
- neg2led and Hannu Nyman who did all the
datasheet digging and debugging.
Cc: Andreas Boehler <dev@aboehler.at>
Suggested-by: Andreas Boehler <dev@aboehler.at>
Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://github.com/openwrt/openwrt/issues/9962
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220607185918.1048204-1-chunkeey@gmail.com
* Call of_platform_populate() for MTD partitions
* Check devicetree alias for index
* mtdoops:
- Add a timestamp to the mtdoops header.
- Create a header structure for the saved mtdoops.
- Fix the size of the header read buffer.
* mtdblock: Warn if opened on NAND
* Bindings:
- reserved-memory: Support MTD/block device
- jedec,spi-nor: remove unneeded properties
- Extend fixed-partitions binding
- Add Sercomm (Suzhou) Corporation vendor prefix
MTD driver changes:
* st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
* phram:
- Allow cached mappings
- Allow probing via reserved-memory
* maps: ixp4xx: Drop driver
* bcm47xxpart: Print correct offset on read error
CFI driver changes:
* Rename chip_ready variables
* Add S29GL064N ID definition
* Use chip_ready() for write on S29GL064N
* Move and rename chip_check/chip_ready/chip_good_for_write
NAND core changes:
* Print offset instead of page number for bad blocks
Raw NAND controller drivers:
* Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
* CS553X: simplify the return expression of cs553x_write_ctrl_byte()
* Davinci: Remove redundant unsigned comparison to zero
* Denali: Use managed device resources
* GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
* Intel: Fix possible null-ptr-deref in ebu_nand_probe()
* MPC5121: Check before clk_disable_unprepare() not needed
* Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
* OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
* Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
* Rockchip: Check before clk_disable_unprepare() not needed
* TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
* Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
* Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
* XTX: Add support for XT26G0xA
SPI NOR core changes:
* Read back written SR value to make sure the write was done correctly.
* Introduce a common function for Read ID that manufacturer drivers can
use to verify the Octal DTR switch worked correctly.
* Add helpers for read/write any register commands so manufacturer
drivers don't open code it every time.
* Clarify rdsr dummy cycles documentation.
* Add debugfs entry to expose internal flash parameters and state.
SPI NOR manufacturer drivers changes:
* Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
* Move spi_nor_write_ear() to Winbond module since only Winbond flashes
use it.
* Rework Micron and Cypress Octal DTR enable methods to improve
readability.
* Use the common Read ID function to verify switch to Octal DTR mode for
Micron and Cypress flashes.
* Skip polling status on volatile register writes for Micron and Cypress
flashes since the operation is instant.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmKHhXEACgkQJWrqGEe9
VoQ4FQgAwTWnv7Eps8ngxlOE1WW1Kx+XUFCYN7mUKmDycgRKWWqF0OUu3pU6T3Si
XoOixajzsPC7AJtXbbGKUkH3UtqapCZ/OVxMJzY1S1zKVgS72ChvPth+rNOA5H6f
wkwCRYBCm51hYAlOQeRoFtwLEpOP17KTZw9Jn/u5RVwbQedQnzPj5sb6PddejjF4
9nlk2auJHzENBEEBG3WLRNgvGep8mNNFarzWB4iWrMcG0w1EgBksbIdshoBmu7vj
nKcDJbyA81DqX+8d56BfAFih8H2yCXZmhUzMK+zqnNkd1NuPnDDnrQYFKmKm2hAg
3bIMIzi+8dl/m0TY6BHPHj8oIYpjYA==
=P95J
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD core changes:
- Call of_platform_populate() for MTD partitions
- Check devicetree alias for index
- mtdoops:
- Add a timestamp to the mtdoops header.
- Create a header structure for the saved mtdoops.
- Fix the size of the header read buffer.
- mtdblock: Warn if opened on NAND
- Bindings:
- reserved-memory: Support MTD/block device
- jedec,spi-nor: remove unneeded properties
- Extend fixed-partitions binding
- Add Sercomm (Suzhou) Corporation vendor prefix
MTD driver changes:
- st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
- phram:
- Allow cached mappings
- Allow probing via reserved-memory
- maps: ixp4xx: Drop driver
- bcm47xxpart: Print correct offset on read error
CFI driver changes:
- Rename chip_ready variables
- Add S29GL064N ID definition
- Use chip_ready() for write on S29GL064N
- Move and rename chip_check/chip_ready/chip_good_for_write
NAND core changes:
- Print offset instead of page number for bad blocks
Raw NAND controller drivers:
- Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
- CS553X: simplify the return expression of cs553x_write_ctrl_byte()
- Davinci: Remove redundant unsigned comparison to zero
- Denali: Use managed device resources
- GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
- Intel: Fix possible null-ptr-deref in ebu_nand_probe()
- MPC5121: Check before clk_disable_unprepare() not needed
- Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
- OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
- Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
- Rockchip: Check before clk_disable_unprepare() not needed
- TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
- Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
- Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
- XTX: Add support for XT26G0xA
SPI NOR core changes:
- Read back written SR value to make sure the write was done
correctly.
- Introduce a common function for Read ID that manufacturer drivers
can use to verify the Octal DTR switch worked correctly.
- Add helpers for read/write any register commands so manufacturer
drivers don't open code it every time.
- Clarify rdsr dummy cycles documentation.
- Add debugfs entry to expose internal flash parameters and state.
SPI NOR manufacturer drivers changes:
- Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
- Move spi_nor_write_ear() to Winbond module since only Winbond
flashes use it.
- Rework Micron and Cypress Octal DTR enable methods to improve
readability.
- Use the common Read ID function to verify switch to Octal DTR mode
for Micron and Cypress flashes.
- Skip polling status on volatile register writes for Micron and
Cypress flashes since the operation is instant"
* tag 'mtd/for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (68 commits)
mtd: st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
dt-bindings: mtd: partitions: Extend fixed-partitions binding
dt-bindings: Add Sercomm (Suzhou) Corporation vendor prefix
mtd: phram: Allow cached mappings
mtd: call of_platform_populate() for MTD partitions
mtd: rawnand: renesas: Use runtime PM instead of the raw clock API
dt-bindings: mtd: renesas: Fix the NAND controller description
mtd: rawnand: mpc5121: Check before clk_disable_unprepare() not needed
mtd: rawnand: rockchip: Check before clk_disable_unprepare() not needed
mtd: nand: MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
mtd: rawnand: cs553x: simplify the return expression of cs553x_write_ctrl_byte()
mtd: rawnand: kioxia: Add support for TH58NVG3S0HBAI4
mtd: spi-nor: debugfs: fix format specifier
mtd: spi-nor: support eon en25qh256a variant
mtd: spi-nor: winbond: add support for W25Q512NW-IM
mtd: spi-nor: expose internal parameters via debugfs
mtd: spi-nor: export spi_nor_hwcaps_pp2cmd()
mtd: spi-nor: move spi_nor_write_ear() to winbond module
mtd: spi-nor: amend the rdsr dummy cycles documentation
mtd: cfi_cmdset_0002: Rename chip_ready variables
...
This NAND controller is part of a well defined power domain handled by
the runtime PM core. Let's keep the harmony with the other RZ/N1 drivers
and exclusively use the runtime PM API to enable/disable the clocks.
We still need to retrieve the external clock rate in order to derive the
NAND timings, but that is not a big deal, we can still do that in the
probe and just save this value to reuse it later.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/linux-mtd/20220513104957.257721-3-miquel.raynal@bootlin.com
All code in clk_disable_unprepare() already checks the clk ptr using
IS_ERR_OR_NULL so there is no need to check it again before calling it.
A lot of other drivers already rely on this behaviour, so it's safe
to do so here.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220512185033.46901-1-phil.edworthy@renesas.com
All code in clk_disable_unprepare() already checks the clk ptr using
IS_ERR_OR_NULL so there is no need to check it again before calling it.
A lot of other drivers already rely on this behaviour, so it's safe
to do so here.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220512184558.45966-1-phil.edworthy@renesas.com
The MediaTek Hardware ECC Engine is only present on MediaTek MT27xx and
MT76xx SoCs. The driver for this engine is a dependency for the
MediaTek NAND controller (MTD_NAND_MTK) and the MediaTek SPI NAND Flash
Interface (SPI_MTK_SNFI) drivers, both of which already depend on
ARCH_MEDIATEK.
Hence add a dependency on ARCH_MEDIATEK to the Hardware ECC Engine
driver, too, to prevent asking the user about this driver when
configuring a kernel without MediaTek SoC support.
Fixes: 4fd62f15afa0d0da ("mtd: nand: make mtk_ecc.c a separated module")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/bb9568e825d4bc7506870b03836baa91bcc4b725.1652104136.git.geert+renesas@glider.be
Add timings for Kioxia/Toshiba TH58NVG3S0HBAI4. Timings
for this memory matches the timings selected for
TH58NVG2S3HBAI4.
This patch increases eraseblock write speed from 5248 KiB/s
to 6864 KiB/s and erase block read speed from 8542 KiB/s
to 18360 KiB/s
Tested on i.MX6SX.
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220429083931.26795-1-rickaran@axis.com
* Also parse the default nand-ecc-engine property if available
* Make mtk_ecc.c a separated module
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmJpa+MACgkQJWrqGEe9
VoTVPwf+PjOPS9MH+3wQkEsqwHtJyC9dvfTRWNSkzJEos0710jl6peeWjo1ift1A
4JLMI3TGHWbNqBykpSLxZPVc6X/toGoMz6/2OussnYQBYgXjLNOgWQqS4kZZmK7D
BARpke8TTqglJyat7NpGNo1EGWA4EtYqwvoPT+H0LMLQbe/NQD0k4RaRNpw+BwPq
gaBHZf/CmN4oG0QrPPvS7jrm0dgWrQgTqRf9zzOnml3m22q3PGMnmY1A1CunBsFn
HK+GxYUOeemPc40mET+U1x6O0+VNlxW2KQ+fZoNHnljd55zq1Cp4mXfr7KuFgfDK
4xMAAoI5cMp8kpLLVUBlD4uzOj3fow==
=FBXD
-----END PGP SIGNATURE-----
Merge tag 'mtd/mtk-spi-nand-for-5.19' into nand/next
Mediatek ECC changes:
* Also parse the default nand-ecc-engine property if available
* Make mtk_ecc.c a separated module
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The recently added ECC engine support introduced a generic property
named nand-ecc-engine for ecc engine phandle. This patch adds support
for this new property.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220424032527.673605-4-gch981213@gmail.com
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
Fixes: 0b1039f016e8 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220426084913.4021868-2-yangyingliang@huawei.com
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Fixes: ec4ba01e894d ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220426084913.4021868-1-yangyingliang@huawei.com
The Toshiba TC58NVG0S3HTA00 is detected with 64 byte OOB while the flash
has 128 bytes OOB. This adds a static NAND ID entry to correct this.
Tested on FRITZ!Box 7530 flashed with OpenWrt.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220420104034.6333-1-dev@aboehler.at
The code change proposes a new way to set bch geometry for large oob
NAND (oobsize > 1KB). In this case, previous implementation can NOT
guarantee the bad block mark always locates in data chunk, so we need a
new way to do it. The general idea is,
1.Try all ECC strength from the maximum ecc that controller can support
to minimum value required by NAND chip, any ECC strength makes the
BBM locate in data chunk can be eligible.
2.If none of them works, using separate ECC for meta, which will add
one extra ecc with the same ECC strength as other data chunks. This
extra ECC can guarantee BBM located in data chunk, also we need to
check if oob can afford it.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-6-han.xu@nxp.com
There is only one variable ecc_chunk_size in bch_geometry data
structure but two different field in BCH registers. The data0_size in
BCH_FLASH0LAYOUT0 and datan_size in BCH_FLASH0LAYOUT1 should have
dedicate variable since they might set to different values in some
cases. For instance, if need dedicate ecc for meta area, the data0_size
should be 0 rather than datan_size, but for all other cases, data0_size
still equals to datan_size and it won't bring any function change.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-5-han.xu@nxp.com
Add nand_ecc_is_strong_enough() check in gpmi_check_ecc() function to
make sure ecc strength can meet chip requirement.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-3-han.xu@nxp.com
The code change refactor the bch geometry setting function, which
doesn't change the default behavior, while user may choose to use chips
required minimum ecc strength by DT flag "fsl,use-minimum-ecc".
The default way to set bch geometry need to set the data chunk
size(step_size) larger than oob size to make sure BBM locates in data
chunk, then set the maximum ecc strength oob can hold. It always use
unbalanced ECC layout, which ecc0 will cover both meta and data0 chunk.
But the default bch setting is deprecated for large oobsize NAND
(oobsize >1KB), so in the patch set, there is a split commit that
introduces a new way to set bch geometry for large oob size NAND.
For all other cases,set the bch geometry by chip required strength and
step size, which uses the minimum ecc strength chip required. It can be
explicitly enabled by DT flag "fsl,use-minimum-ecc", but need to be
en/disabled in both u-boot and kernel at the same time.
Signed-off-by: Han Xu <han.xu@nxp.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-2-han.xu@nxp.com
All of the resources used by this driver has managed interfaces, so use
them. Otherwise we will get the following splat:
[ 4.472703] denali-nand-pci 0000:00:05.0: timeout while waiting for irq 0x1000
[ 4.474071] denali-nand-pci: probe of 0000:00:05.0 failed with error -5
[ 4.473538] nand: No NAND device found
[ 4.474068] BUG: unable to handle page fault for address: ffffc90005000410
[ 4.475169] #PF: supervisor write access in kernel mode
[ 4.475579] #PF: error_code(0x0002) - not-present page
[ 4.478362] RIP: 0010:iowrite32+0x9/0x50
[ 4.486068] Call Trace:
[ 4.486269] <IRQ>
[ 4.486443] denali_isr+0x15b/0x300 [denali]
[ 4.486788] ? denali_direct_write+0x50/0x50 [denali]
[ 4.487189] __handle_irq_event_percpu+0x161/0x3b0
[ 4.487571] handle_irq_event+0x7d/0x1b0
[ 4.487884] handle_fasteoi_irq+0x2b0/0x770
[ 4.488219] __common_interrupt+0xc8/0x1b0
[ 4.488549] common_interrupt+0x9a/0xc0
Fixes: 93db446a424c ("mtd: nand: move raw NAND related code to the raw/ subdir")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220411125808.958276-1-zheyuma97@gmail.com
This patch fixes a memory corruption that occurred in the
nand_scan() path for Hynix nand device.
On boot, for Hynix nand device will panic at a weird place:
| Unable to handle kernel NULL pointer dereference at virtual
address 00000070
| [00000070] *pgd=00000000
| Internal error: Oops: 5 [#1] PREEMPT SMP ARM
| Modules linked in:
| CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.17.0-01473-g13ae1769cfb0
#38
| Hardware name: Generic DT based system
| PC is at nandc_set_reg+0x8/0x1c
| LR is at qcom_nandc_command+0x20c/0x5d0
| pc : [<c088b74c>] lr : [<c088d9c8>] psr: 00000113
| sp : c14adc50 ip : c14ee208 fp : c0cc970c
| r10: 000000a3 r9 : 00000000 r8 : 00000040
| r7 : c16f6a00 r6 : 00000090 r5 : 00000004 r4 :c14ee040
| r3 : 00000000 r2 : 0000000b r1 : 00000000 r0 :c14ee040
| Flags: nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
| Control: 10c5387d Table: 8020406a DAC: 00000051
| Register r0 information: slab kmalloc-2k start c14ee000 pointer offset
64 size 2048
| Process swapper/0 (pid: 1, stack limit = 0x(ptrval))
| nandc_set_reg from qcom_nandc_command+0x20c/0x5d0
| qcom_nandc_command from nand_readid_op+0x198/0x1e8
| nand_readid_op from hynix_nand_has_valid_jedecid+0x30/0x78
| hynix_nand_has_valid_jedecid from hynix_nand_init+0xb8/0x454
| hynix_nand_init from nand_scan_with_ids+0xa30/0x14a8
| nand_scan_with_ids from qcom_nandc_probe+0x648/0x7b0
| qcom_nandc_probe from platform_probe+0x58/0xac
The problem is that the nand_scan()'s qcom_nand_attach_chip callback
is updating the nandc->max_cwperpage from 1 to 4 or 8 based on page size.
This causes the sg_init_table of clear_bam_transaction() in the driver's
qcom_nandc_command() to memset much more than what was initially
allocated by alloc_bam_transaction().
This patch will update nandc->max_cwperpage 1 to 4 or 8 based on page
size in qcom_nand_attach_chip call back after freeing the previously
allocated memory for bam txn as per nandc->max_cwperpage = 1 and then
again allocating bam txn as per nandc->max_cwperpage = 4 or 8 based on
page size in qcom_nand_attach_chip call back itself.
Cc: stable@vger.kernel.org
Fixes: 6a3cec64f18c ("mtd: rawnand: qcom: convert driver to nand_scan()")
Reported-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Co-developed-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1650268107-5363-1-git-send-email-quic_mdalam@quicinc.com
wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.
Fixes: 83738d87e3a0 ("mtd: sh_flctl: Add DMA capabilty")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412083435.29254-1-linmq006@gmail.com
According to the datasheet, mt7622 only has 5 ECC capabilities instead
of 7, and the decoding error register is arranged as follows:
+------+---------+---------+---------+---------+
| Bits | 19:15 | 14:10 | 9:5 | 4:0 |
+------+---------+---------+---------+---------+
| Name | ERRNUM3 | ERRNUM2 | ERRNUM1 | ERRNUM0 |
+------+---------+---------+---------+---------+
This means err_mask should be 0x1f instead of 0x3f and the number of
bits shifted in mtk_ecc_get_stats should be 5 instead of 8.
This commit introduces err_shift for the difference in this register
and fix other existing parameters.
Public MT7622 reference manual can be found on [0] and the info this
commit is based on is from page 656 and page 660.
[0]: https://wiki.banana-pi.org/Banana_Pi_BPI-R64#Documents
Fixes: 98dea8d71931 ("mtd: nand: mtk: Support MT7622 NAND flash controller.")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220402160315.919094-1-gch981213@gmail.com
This makes printed info consistent with other kernel messages. After
scanning NAND BBT create_bbt() prints offset of each bad block. This
change makes is easy to verify nand_erase_nand() failure reason.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220326163304.30806-1-zajec5@gmail.com
Add support for:
GD5F{1,2}GM7{U,R}ExxG
GD5F4GM8{U,R}ExxG
These are new 27nm counterparts for the GD5FxGQ4 chips from GigaDevice
with 8b/512b on-die ECC capability.
These chips (and currently supported GD5FxGQ5 chips) have QIO DTR
instruction for reading page cache. It isn't added in this patch because
I don't have a DTR spi controller for testing.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220320100001.247905-6-gch981213@gmail.com
Add support for:
GD5F2GQ5{U,R}ExxG
GD5F4GQ6{U,R}ExxG
These chips uses 4 dummy bytes for quad io and 2 dummy bytes for dual io.
Besides that and memory layout, they are identical to their 1G variant.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220320100001.247905-5-gch981213@gmail.com
Add support for:
GD5F1GQ4RExxG
GD5F2GQ4{U,R}ExxG
These chips differ from GD5F1GQ4UExxG only in chip ID, voltage
and capacity.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220320100001.247905-3-gch981213@gmail.com
* Replace the expert mode symbols with a single helper
* Fix misuses of of_match_ptr()
* Remove partid and partname debugfs files
* tests: Fix eraseblock read speed miscalculation for lower partition sizes
* TRX parser: Allow to use on MediaTek MIPS SoCs
MTD driver changes:
* spear_smi: use GFP_KERNEL
* mchp48l640: Add SPI ID table
* mchp23k256: Add SPI ID table
* blkdevs: Avoid soft lockups with some mtd/spi devices
* aspeed-smc: Improve probe resilience
Hyperbus changes:
* HBMC_AM654 should depend on ARCH_K3
NAND core changes:
* ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
* Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
- Make two read-only arrays static const
- Fix compile test issue
Raw NAND core changes:
* Fix misuses of of_match_node()
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
SPI-NAND core changes:
* Delay a little bit the dirmap creation
* Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
* macronix: Use random program load
SPI NOR core changes:
* Move vendor specific code out of the core into vendor drivers.
* Unify all function and object names in the vendor modules.
* Make setup() callback optional to improve readability.
* Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
SPI changes:
* Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
* spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Binding changes:
* Dropped mtd/cortina,gemini-flash.txt
* Convert BCM47xx partitions to json-schema
* Vendor prefixes: Clarify Macronix prefix
* SPI NAND: Convert spi-nand description file to yaml
* Raw NAND chip: Create a NAND chip description
* Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
* Describe Macronix NAND ECC engine
* Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmI7WJcACgkQJWrqGEe9
VoSzpAgAutzRv9TRUiXdBGGlJ851QaZ6ZUvT1bHKTQA+xZi+MZyNmc0cWNg3B70I
PnwyxNAmRkUQKwV5Vgy/sQrt42qZnPmr+8XMq+UiziPmgFdjiTdLqGcN619Hi12t
JqtoKL828R064LSEq5nWsJ2waoGT1nNtZK8kA2qe8ctvmH0YTThriVZUQR4/Befb
OGFheceLFycE/vkktPPr3As4603fMiyDOT7EA3Mtzgjohry0a0TqoakHCaHC/fYo
0/h+x+jJATPtgbWm1ZiV3cZ/Su00+rKuQOsiAWvM/pqDaijsVntBmtK0PRtums2Q
m8LCspuQYNnCINeQXqba9RxACpibDg==
=+6Zk
-----END PGP SIGNATURE-----
Merge tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"There has been a lot of activity in the MTD subsystem recently, with a
number of SPI-NOR cleanups as well as the introduction of ECC engines
that can be used by SPI controllers (hence a few SPI patches in here).
Core MTD changes:
- Replace the expert mode symbols with a single helper
- Fix misuses of of_match_ptr()
- Remove partid and partname debugfs files
- tests: Fix eraseblock read speed miscalculation for lower partition
sizes
- TRX parser: Allow to use on MediaTek MIPS SoCs
MTD driver changes:
- spear_smi: use GFP_KERNEL
- mchp48l640: Add SPI ID table
- mchp23k256: Add SPI ID table
- blkdevs: Avoid soft lockups with some mtd/spi devices
- aspeed-smc: Improve probe resilience
Hyperbus changes:
- HBMC_AM654 should depend on ARCH_K3
NAND core changes:
- ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
- Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
- Make two read-only arrays static const
- Fix compile test issue
Raw NAND core changes:
- Fix misuses of of_match_node()
- Rework of_get_nand_bus_width()
- Remove of_get_nand_on_flash_bbt() wrapper
- Protect access to rawnand devices while in suspend
- bindings: Document the wp-gpios property
Rax NAND controller driver changes:
- atmel: Fix refcount issue in atmel_nand_controller_init
- nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
- rockchip: Fix platform_get_irq.cocci warning
- stm32_fmc2: Add NAND Write Protect support
- pl353: Set the nand chip node as the flash node
- brcmnand: Fix sparse warnings in bcma_nand
- omap_elm: Remove redundant variable 'errors'
- gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
- brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
- Check for error irq
SPI-NAND core changes:
- Delay a little bit the dirmap creation
- Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
- macronix: Use random program load
SPI NOR core changes:
- Move vendor specific code out of the core into vendor drivers.
- Unify all function and object names in the vendor modules.
- Make setup() callback optional to improve readability.
- Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
SPI changes:
- Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
- spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Binding changes:
- Dropped mtd/cortina,gemini-flash.txt
- Convert BCM47xx partitions to json-schema
- Vendor prefixes: Clarify Macronix prefix
- SPI NAND: Convert spi-nand description file to yaml
- Raw NAND chip: Create a NAND chip description
- Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
- Describe Macronix NAND ECC engine
- Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory"
* tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (104 commits)
mtd: nand: ecc: mxic: Fix compile test issue
mtd: nand: mxic-ecc: make two read-only arrays static const
mtd: hyperbus: HBMC_AM654 should depend on ARCH_K3
mtd: core: Remove partid and partname debugfs files
dt-bindings: mtd: partitions: convert BCM47xx to the json-schema
mtd: tests: Fix eraseblock read speed miscalculation for lower partition sizes
mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init
mtd: rawnand: rockchip: fix platform_get_irq.cocci warning
mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set
mtd: spi-nor: renumber flags
mtd: spi-nor: slightly change code style in spi_nor_sr_ready()
mtd: spi-nor: spansion: rename vendor specific functions and defines
mtd: spi-nor: spansion: convert USE_CLSR to a manufacturer flag
mtd: spi-nor: move all spansion specifics into spansion.c
mtd: spi-nor: spansion: slightly rework control flow in late_init()
mtd: spi-nor: micron-st: rename vendor specific functions and defines
mtd: spi-nor: micron-st: convert USE_FSR to a manufacturer flag
mtd: spi-nor: move all micron-st specifics into micron-st.c
mtd: spi-nor: xilinx: correct the debug message
mtd: spi-nor: xilinx: rename vendor specific functions and defines
...
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmI021sACgkQJWrqGEe9
VoTEcggAiFXD+oR0VXTsykiNDiopsAUZwLPGuqk8gvD4ozOYCoAEoYrtnBM6Uybz
W6Hu6Eow/ri1H+uVygUw3RYa4TpxrZrmZnJ1YimXxZjbLYjgE3FS9vzh2l4Bu3yo
fkkQH+nFvk9qVIK8qolAny+LWl37gkSnCd6mPPksYaG5Ds1n1ZgyTZVUz5TOWAjG
QAWUQQfO1iu7+u4CXa9JRTkCf55bT6v6c9Ryq6MA+ok6jVRN6Cj9WhxHtCB5vmOH
Ndmu4V8BqaNKg39ltolqSPuwt3GEh707LRr+YakfnaOM7Sf8E/evn/THSkHwY/yn
bAjpU1gvS13nJ++s8nHwIhHKhoYjTg==
=4Uke
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.18' into mtd/next
Raw NAND core changes:
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- move vendor specific code out of the core into vendor drivers.
- unify all function and object names in the vendor modules.
- make setup() callback optional to improve readability.
- skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmInffUACgkQS1VPR6WN
FOn9fwf/SCIvgoScBNeQjW4cGTmh11oO+O8i2umibq0pQDLrNF6Ul7ykY6Fdm4Dc
+Ce7c4Vp0O+DRphIkaK5MtNgRmXMOQbqUKcNAQftFS0wCtJ+QVQzOvkVGS3jQA74
KVEY3Jiup3Q5qknBg0r890ENwRLmcGJaPi5DAO+uHcf6ItTpwjv3z6C2ZUeiH6UK
PMSwZgd86dwwH2eU4G5EoAjA+nqOcVvH0V1F49DFsGZ3kkmUS6nMNnSpb5SykszT
4uq+7+c3E2UOC0TlUkyX/xTv4DoZZDi6qqVEaV14bELL1a0FdltjKyIuWTds1Tei
rwPhEOkqOpSnBVjlUWb7icwef21NWg==
=QFe+
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.18' into mtd/next
SPI NOR core changes:
- move vendor specific code out of the core into vendor drivers.
- unify all function and object names in the vendor modules.
- make setup() callback optional to improve readability.
- skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Avoid random build errors with architectures which do not select
HAS_IOMEM by depending on it in Kconfig.
This fixes the following warning:
/home/mraynal/0day/gcc-11.2.0-nolibc/s390-linux/bin/s390-linux-ld:
drivers/mtd/nand/ecc-mxic.o: in function `mxic_ecc_probe':
ecc-mxic.c:(.text+0x2244): undefined reference to `devm_platform_ioremap_resource'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220314152336.75447-1-miquel.raynal@bootlin.com
Don't populate the read-only arrays possible_strength and
spare_size on the stack but instead make them static
const. Also makes the object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220307230940.169235-1-colin.i.king@gmail.com
The reference counting issue happens in several error handling paths
on a refcounted object "nc->dmac". In these paths, the function simply
returns the error code, forgetting to balance the reference count of
"nc->dmac", increased earlier by dma_request_channel(), which may
cause refcount leaks.
Fix it by decrementing the refcount of specific object in those error
paths.
Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver")
Co-developed-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Co-developed-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220304085330.3610-1-xiongx18@fudan.edu.cn
The root of the problem is that we are selecting symbols that have
dependencies. This can cause random configurations that can fail.
The cleanest solution is to avoid using select.
This driver uses interfaces from the OMAP_GPMC driver so we have to
depend on it instead.
Fixes: 4cd335dae3cf ("mtd: rawnand: omap2: Prevent invalid configuration and build error")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/linux-mtd/20220219193600.24892-1-rogerq@kernel.org
This patch adds the support of the WP# signal. WP will be disabled in
probe/resume callbacks and will be enabled in remove/suspend callbacks.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220217144755.270679-3-christophe.kerello@foss.st.com
In devicetree the flash information is embedded within nand chip node,
so during nand chip initialization the nand chip node should be passed
to nand_set_flash_node() api, instead of nand controller node.
Fixes: 08d8c62164a3 ("mtd: rawnand: pl353: Add support for the ARM PL353 SMC NAND controller")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220209053427.27676-1-amit.kumar-mahapatra@xilinx.com
that can be used by SPI controllers to manage SPI NANDs as well as
possibly by parallel NAND controllers. In particular, it brings support
for Macronix ECC engine that can be used with Macronix SPI controller.
The changes touch the NAND core, the NAND ECC core, the spi-mem layer, a
SPI controller driver and add a new NAND ECC driver, as well as a number
of binding updates.
Binding changes:
* Vendor prefixes: Clarify Macronix prefix
* SPI NAND: Convert spi-nand description file to yaml
* Raw NAND chip: Create a NAND chip description
* Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
* Describe Macronix NAND ECC engine
* Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory
NAND core changes:
* ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
* Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
SPI-NAND core changes:
* Delay a little bit the dirmap creation
* Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
* macronix: Use random program load
SPI changes:
* Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
* spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmIPpwcACgkQJWrqGEe9
VoRbnwgAgW9tSKGp1B6eA3Xf7Or0SZfmC6H0scV8kfQ2i9OnMOuYMAGs+7whNrcx
Dvb9IfFOMra7umid98EI58YhLsu4IMDtc79Lp04HGY/emjZh47FpAEXZ/vr/45e9
lclUEmjHwUVJ5+XvFwnPLpIWiM0xeL3CN2rAi76uI5sII+Hxt6KkV7L9+N9IjhcA
GsG/8/A16ihbNjVrHoN+ofwmmZkySXvhK7IIg93Tv+VoJCBnn0eEDgtRXvsGoDuq
2xD87MEAhnXw+q9LtSSUwmA/uUCR2RscidGQ+LML0PwKDVUZhzBV8sNrNoPQy374
51XXDCkSF8NRK+FVXIUFTEctdVrE1A==
=UuhB
-----END PGP SIGNATURE-----
Merge tag 'mtd/spi-mem-ecc-for-5.18' into mtd/next
Topic branch bringing-in changes related to the support of ECC engines
that can be used by SPI controllers to manage SPI NANDs as well as
possibly by parallel NAND controllers. In particular, it brings support
for Macronix ECC engine that can be used with Macronix SPI controller.
The changes touch the NAND core, the NAND ECC core, the spi-mem layer, a
SPI controller driver and add a new NAND ECC driver, as well as a number
of binding updates.
Binding changes:
* Vendor prefixes: Clarify Macronix prefix
* SPI NAND: Convert spi-nand description file to yaml
* Raw NAND chip: Create a NAND chip description
* Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
* Describe Macronix NAND ECC engine
* Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory
NAND core changes:
* ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
* Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
SPI-NAND core changes:
* Delay a little bit the dirmap creation
* Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
* macronix: Use random program load
SPI changes:
* Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
* spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
In order for pipelined ECC engines to be able to enable/disable the ECC
engine only when needed and avoid races when future parallel-operations
will be supported, we need to provide the information about the use of
the ECC engine in the direct mapping hooks. As direct mapping
configurations are meant to be static, it is best to create two new
mappings: one for regular 'raw' accesses and one for accesses involving
correction. It is up to the driver to use or not the new ECC enable
boolean contained in the spi-mem operation.
As dirmaps are not free (they consume a few pages of MMIO address space)
and because these extra entries are only meant to be used by pipelined
engines, let's limit their use to this specific type of engine and save
a bit of memory with all the other setups.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-9-miquel.raynal@bootlin.com
As we will soon tweak the dirmap creation to act a little bit
differently depending on the picked ECC engine, we need to initialize
dirmaps after ECC engines. This should not have any effect as dirmaps
are not yet used at this point.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-8-miquel.raynal@bootlin.com
Introduce the support for another possible configuration: the ECC
engine may work as DMA master (pipelined) and move itself the data
to/from the NAND chip into the buffer, applying the necessary
corrections/computations on the fly.
This driver offers an ECC engine implementation that must be
instatiated from a SPI controller driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-17-miquel.raynal@bootlin.com
In a pipelined engine situation, we might either have the host which
internally has support for error correction, or have it using an
external hardware block for this purpose. In the former case, the host
is also the ECC engine. In the latter case, it is not. In order to get
the right pointers on the right devices (for example: in order to devm_*
allocate variables), let's introduce this helper which can safely be
called by pipelined ECC engines in order to retrieve the right device
structure.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-16-miquel.raynal@bootlin.com
