IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 53dd0a7cd65edc83b0c243d1c08377c8b876b2ee upstream.
SAMA5D2x doesn't drive CMD line if GPIO is used as CD line (at least
SAMA5D27 doesn't). Fix this by forcing card-detect in the module
if module-controlled CD is not used.
Fixed commit addresses the problem only for non-removable cards. This
amends it to also cover gpio-cd case.
Cc: stable@vger.kernel.org
Fixes: 7a1e3f143176 ("mmc: sdhci-of-at91: force card detect value for non removable devices")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/8d10950d9940468577daef4772b82a071b204716.1584290561.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b500c086e4110829a308c23e83a7cdc65b26228a upstream.
At the moment, reading from in_magn_*_raw in sysfs tends to return
large values around 65000, even though the output of ak8974 is actually
limited to ±32768. This happens because the value is never converted
to the signed 16-bit integer variant.
Add an explicit cast to s16 to fix this.
Fixes: 7c94a8b2ee8c ("iio: magn: add a driver for AK8974")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Waleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29e8c8253d7d5265f58122c0a7902e26df6c6f61 upstream.
Master mode should be disabled when stopping. This mainly impacts
possible other use-case after timer has been stopped. Currently,
master mode remains set (from start routine).
Fixes: 6fb34812c2a2 ("iio: stm32 trigger: Add support for TRGO2 triggers")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5461e0530c222129dfc941058be114b5cbc00837 upstream.
The return value checks in snd_pcm_plug_alloc() are covered with
snd_BUG_ON() macro that may trigger a kernel WARNING depending on the
kconfig. But since the error condition can be triggered by a weird
user space parameter passed to OSS layer, we shouldn't give the kernel
stack trace just for that. As it's a normal error condition, let's
remove snd_BUG_ON() macro usage there.
Reported-by: syzbot+2a59ee7a9831b264f45e@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200312155730.7520-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2ecf903ef06eb1bbbfa969db9889643d487e73a upstream.
Each OSS PCM plugins allocate its internal buffer per pre-calculation
of the max buffer size through the chain of plugins (calling
src_frames and dst_frames callbacks). This works for most plugins,
but the rate plugin might behave incorrectly. The calculation in the
rate plugin involves with the fractional position, i.e. it may vary
depending on the input position. Since the buffer size
pre-calculation is always done with the offset zero, it may return a
shorter size than it might be; this may result in the out-of-bound
access as spotted by fuzzer.
This patch addresses those possible buffer overflow accesses by simply
setting the upper limit per the given buffer size for each plugin
before src_frames() and after dst_frames() calls.
Reported-by: syzbot+e1fe9f44fb8ecf4fb5dd@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/000000000000b25ea005a02bcf21@google.com
Link: https://lore.kernel.org/r/20200309082148.19855-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4384f167ce5fa7241b61bb0984d651bc528ddebe upstream.
The virmidi driver handles sysex event exceptionally in a short-cut
snd_seq_dump_var_event() call, but this missed the reset of the
running status. As a result, it may lead to an incomplete command
right after the sysex when an event with the same running status was
queued.
Fix it by clearing the running status properly via alling
snd_midi_event_reset_decode() for that code path.
Reported-by: Andreas Steinmetz <ast@domdv.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/3b4a4e0f232b7afbaf0a843f63d0e538e3029bfd.camel@domdv.de
Link: https://lore.kernel.org/r/20200316090506.23966-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d683469b3c93d7e2afd39e6e1970f24700eb7a68 upstream.
The MIDI input event parser of the LINE6 driver may enter into an
endless loop when the unexpected data sequence is given, as it tries
to continue the secondary bytes without termination. Also, when the
input data is too short, the parser returns a negative error, while
the caller doesn't handle it properly. This would lead to the
unexpected behavior as well.
This patch addresses those issues by checking the return value
correctly and handling the one-byte event in the parser properly.
The bug was reported by syzkaller.
Reported-by: syzbot+cce32521ee0a824c21f7@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/000000000000033087059f8f8fa3@google.com
Link: https://lore.kernel.org/r/20200309095922.30269-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16263abc12d09871156a1c8650fb651f0e552f5e upstream.
This controller timeouts during suspend (S3) with
[ 240.521724] xhci_hcd 0000:30:00.3: WARN: xHC save state timeout
[ 240.521729] xhci_hcd 0000:30:00.3: ERROR mismatched command completion event
thus preventing the system from entering S3.
Moreover it remains in an undefined state where some connected devices stop
working until a reboot.
Apply the XHCI_SUSPEND_DELAY quirk to make it suspend properly.
CC: stable@vger.kernel.org
Signed-off-by: Alberto Mattea <alberto@mattea.info>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200306150858.21904-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cecc113c1af0dd41ccf265c1fdb84dbd05e63423 upstream.
Add a device id for HP LD381 Display
LD381: 03f0:0f7f
Signed-off-by: Scott Chen <scott@labau.com.tw>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b433e340e7565110b0ce9ca4b3e26f4b97a1decf upstream.
When loading new kernel via kexec, we need to shutdown host controller to
avoid any un-expected memory accessing during new kernel boot.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200306092328.41253-1-ran.wang_1@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75d7676ead19b1fbb5e0ee934c9ccddcb666b68c upstream.
We have been receiving bug reports that ethernet connections over
RTL8153 based ethernet adapters stops working after a while with
errors like these showing up in dmesg when the ethernet stops working:
[12696.189484] r8152 6-1:1.0 enp10s0u1: Tx timeout
[12702.333456] r8152 6-1:1.0 enp10s0u1: Tx timeout
[12707.965422] r8152 6-1:1.0 enp10s0u1: Tx timeout
This has been reported on Dell WD15 docks, Belkin USB-C Express Dock 3.1
docks and with generic USB to ethernet dongles using the RTL8153
chipsets. Some users have tried adding usbcore.quirks=0bda:8153:k to
the kernel commandline and all users who have tried this report that
this fixes this.
Also note that we already have an existing NO_LPM quirk for the RTL8153
used in the Microsoft Surface Dock (where it uses a different usb-id).
This commit adds a NO_LPM quirk for the generic Realtek RTL8153
0bda:8153 usb-id, fixing the Tx timeout errors on these devices.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=198931
Cc: stable@vger.kernel.org
Cc: russianneuromancer@ya.ru
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200313120708.100339-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b63e48fb50e1ca71db301ca9082befa6f16c55c4 upstream.
Realtek Hub (0bda:0x0487) used in Dell Dock WD19 sometimes drops off the
bus when bringing underlying ports from U3 to U0.
Disabling LPM on the hub during setting link state is not enough, so
let's disable LPM completely for this hub.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200205112633.25995-3-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 611d61f9ac99dc9e1494473fb90117a960a89dfa ]
This makes the script more convenient to run.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14afc59361976c0ba39e3a9589c3eaa43ebc7e1d ]
The bfq_find_set_group() function takes as input a blkcg (which represents
a cgroup) and retrieves the corresponding bfq_group, then it updates the
bfq internal group hierarchy (see comments inside the function for why
this is needed) and finally it returns the bfq_group.
In the hierarchy update cycle, the pointer holding the correct bfq_group
that has to be returned is mistakenly used to traverse the hierarchy
bottom to top, meaning that in each iteration it gets overwritten with the
parent of the current group. Since the update cycle stops at root's
children (depth = 2), the overwrite becomes a problem only if the blkcg
describes a cgroup at a hierarchy level deeper than that (depth > 2). In
this case the root's child that happens to be also an ancestor of the
correct bfq_group is returned. The main consequence is that processes
contained in a cgroup at depth greater than 2 are wrongly placed in the
group described above by BFQ.
This commits fixes this problem by using a different bfq_group pointer in
the update cycle in order to avoid the overwrite of the variable holding
the original group reference.
Reported-by: Kwon Je Oh <kwonje.oh2@gmail.com>
Signed-off-by: Carlo Nonato <carlo.nonato95@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8130b9d5b5abf26f9927b487c15319a187775f34 ]
This patch adds the barrier to guarantee that req->err is always updated
before req->state.
Otherwise, read_reply() would not return ERR_PTR(req->err) but
req->body, when process_writes()->xb_write() is failed.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Link: https://lore.kernel.org/r/20200303221423.21962-2-dongli.zhang@oracle.com
Reviewed-by: Julien Grall <jgrall@amazon.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b17159e52bb31f982f82a6278acd7fab1d3f67b ]
Also, save/restore __bi_remaining in case the bio was used in a
BIO_CHAIN (e.g. due to blk_queue_split).
Suggested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3745488e9d599916a0b40d45d3f30e3d4720288e ]
altera_get_note is called from altera_init, where key is kzalloc(33).
When the allocation functions are annotated to allow the compiler to see
the sizes of objects, and with FORTIFY_SOURCE, we see:
In file included from drivers/misc/altera-stapl/altera.c:14:0:
In function ‘strlcpy’,
inlined from ‘altera_init’ at drivers/misc/altera-stapl/altera.c:2189:5:
include/linux/string.h:378:4: error: call to ‘__write_overflow’ declared with attribute error: detected write beyond size of object passed as 1st parameter
__write_overflow();
^~~~~~~~~~~~~~~~~~
That refers to this code in altera_get_note:
if (key != NULL)
strlcpy(key, &p[note_strings +
get_unaligned_be32(
&p[note_table + (8 * i)])],
length);
The error triggers because the length of 'key' is 33, but the copy
uses length supplied as the 'length' parameter, which is always
256. Split the size parameter into key_len and val_len, and use the
appropriate length depending on what is being copied.
Detected by compiler error, only compile-tested.
Cc: "Igor M. Liplianin" <liplianin@netup.ru>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Link: https://lore.kernel.org/r/20200120074344.504-2-dja@axtens.net
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/202002251042.D898E67AC@keescook
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ba52ad55b533760a1f65836aa0ec9d35e36bb4f ]
Fix bogus NULL checks on the return value of acpi_cpu_get_madt_gicc()
by checking for a 0 'gicc->performance_interrupt' value instead.
Signed-off-by: Liguang Zhang <zhangliguang@linux.alibaba.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0fd99d659ba5582e09625c7a985d63fc2ca74b5 ]
Writing to the built-in strings arrays doesn't work if driver is loaded
as kernel module. This is also considered as a bad pattern. Fix this by
adding a call to clk_get() with legacy clock name. This fixes following
kernel oops if driver is loaded as module:
Unable to handle kernel paging request at virtual address bf047978
pgd = (ptrval)
[bf047978] *pgd=59344811, *pte=5903c6df, *ppte=5903c65f
Internal error: Oops: 80f [#1] SMP ARM
Modules linked in: mc exynosdrm(+) analogix_dp rtc_s3c exynos_ppmu i2c_gpio
CPU: 1 PID: 212 Comm: systemd-udevd Not tainted 5.6.0-rc2-next-20200219 #326
videodev: Linux video capture interface: v2.00
Hardware name: Samsung Exynos (Flattened Device Tree)
PC is at exynos_dsi_probe+0x1f0/0x384 [exynosdrm]
LR is at exynos_dsi_probe+0x1dc/0x384 [exynosdrm]
...
Process systemd-udevd (pid: 212, stack limit = 0x(ptrval))
...
[<bf03cf14>] (exynos_dsi_probe [exynosdrm]) from [<c09b1ca0>] (platform_drv_probe+0x6c/0xa4)
[<c09b1ca0>] (platform_drv_probe) from [<c09afcb8>] (really_probe+0x210/0x350)
[<c09afcb8>] (really_probe) from [<c09aff74>] (driver_probe_device+0x60/0x1a0)
[<c09aff74>] (driver_probe_device) from [<c09b0254>] (device_driver_attach+0x58/0x60)
[<c09b0254>] (device_driver_attach) from [<c09b02dc>] (__driver_attach+0x80/0xbc)
[<c09b02dc>] (__driver_attach) from [<c09ade00>] (bus_for_each_dev+0x68/0xb4)
[<c09ade00>] (bus_for_each_dev) from [<c09aefd8>] (bus_add_driver+0x130/0x1e8)
[<c09aefd8>] (bus_add_driver) from [<c09b0d64>] (driver_register+0x78/0x110)
[<c09b0d64>] (driver_register) from [<bf038558>] (exynos_drm_init+0xe8/0x11c [exynosdrm])
[<bf038558>] (exynos_drm_init [exynosdrm]) from [<c0302fa8>] (do_one_initcall+0x50/0x220)
[<c0302fa8>] (do_one_initcall) from [<c03dd02c>] (do_init_module+0x60/0x210)
[<c03dd02c>] (do_init_module) from [<c03dbf44>] (load_module+0x1c0c/0x2310)
[<c03dbf44>] (load_module) from [<c03dc85c>] (sys_finit_module+0xac/0xbc)
[<c03dc85c>] (sys_finit_module) from [<c0301000>] (ret_fast_syscall+0x0/0x54)
Exception stack(0xd979bfa8 to 0xd979bff0)
...
---[ end trace db16efe05faab470 ]---
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a9d1e3f3f038785ebc72d53f1c409d07f6b4ff5 ]
Properly propagate error value from devm_regulator_bulk_get() and don't
confuse user with meaningless warning about failure in getting regulators
in case of deferred probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dd8304981ecffa77bb72b1c57c4be5dfe6cfae9 ]
In the public interface for chipselect, there is always an entry
commented as "Dummy generic FIFO entry" pushed down to the fifo right
after the activate/deactivate command. The dummy entry is 0x0,
irregardless if the intention was to activate or deactive the cs. This
causes the cs line to glitch rather than beeing activated in the case
when there was an activate command.
This has been observed on oscilloscope, and have caused problems for at
least one specific flash device type connected to the qspi port. After
the change the glitch is gone and cs goes active when intended.
The reason why this worked before (except for the glitch) was because
when sending the actual data, the CS bits are once again set. Since
most flashes uses mode 0, there is always a half clk period anyway for
cs to clk active setup time. If someone would rely on timing from a
chip_select call to a transfer_one, it would fail though.
It is unknown why the dummy entry was there in the first place, git log
seems to be of no help in this case. The reference manual gives no
indication of the necessity of this. In fact the lower 8 bits are a
setup (or hold in case of deactivate) time expressed in cycles. So this
should not be needed to fulfill any setup/hold timings.
Signed-off-by: Thommy Jakobsson <thommyj@gmail.com>
Reviewed-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Link: https://lore.kernel.org/r/20200224162643.29102-1-thommyj@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 683f65ded66a9a7ff01ed7280804d2132ebfdf7e ]
In some circumstances on Intel LPSS controllers, toggling the LPSS
CS control register doesn't actually cause the CS line to toggle.
This seems to be failure of dynamic clock gating that occurs after
going through a suspend/resume transition, where the controller
is sent through a reset transition. This ruins SPI transactions
that either rely on delay_usecs, or toggle the CS line without
sending data.
Whenever CS is toggled, momentarily set the clock gating register
to "Force On" to poke the controller into acting on CS.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20200211223700.110252-1-rajatja@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27f13774654ea6bd0b6fc9b97cce8d19e5735661 ]
'dma-ranges' in a PCI bridge node does correctly set dma masks for PCI
devices not described in the DT. Certain DRA7 platforms (e.g., DRA76)
has RAM above 32-bit boundary (accessible with LPAE config) though the
PCIe bridge will be able to access only 32-bits. Add 'dma-ranges'
property in PCIe RC DT nodes to indicate the host bridge can access
only 32 bits.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb0cc635c7a9fa8a3a0f75d4d896721819c63add ]
Selecting CONFIG_DEBUG_INFO_BTF results in the below warning from ld:
ld: warning: orphan section `.BTF' from `.btf.vmlinux.bin.o' being placed in section `.BTF'
Include .BTF section in vmlinux explicitly to fix the same.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200220113132.857132-1-naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 136b5cd2e2f97581ae560cff0db2a3b5369112da ]
spi_qup_suspend() will cause synchronous external abort when
runtime suspend is enabled and applied, as it tries to
access SPI controller register while clock is already disabled
in spi_qup_pm_suspend_runtime().
Signed-off-by: Yuji sasaki <sasakiy@chromium.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200214074340.2286170-1-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3e72dfdf8227b052393f71d820ec7599909dddc2 upstream.
Similarly to commit c543cb4a5f07 ("ipv4: ensure rcu_read_lock() in
ipv4_link_failure()"), __ip_options_compile() must be called under rcu
protection.
Fixes: 3da1ed7ac398 ("net: avoid use IPCB in cipso_v4_error")
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd4d9c7d0c71866ec0c2825189ebd2ce35bd95b8 upstream.
When kmem_cache_alloc_bulk() attempts to allocate N objects from a percpu
freelist of length M, and N > M > 0, it will first remove the M elements
from the percpu freelist, then call ___slab_alloc() to allocate the next
element and repopulate the percpu freelist. ___slab_alloc() can re-enable
IRQs via allocate_slab(), so the TID must be bumped before ___slab_alloc()
to properly commit the freelist head change.
Fix it by unconditionally bumping c->tid when entering the slowpath.
Cc: stable@vger.kernel.org
Fixes: ebe909e0fdb3 ("slub: improve bulk alloc strategy")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45939ce292b4b11159719faaf60aba7d58d5fe33 upstream.
It is possible for a system with an ARMv8 timer to run a 32-bit kernel.
When this happens we will unconditionally have the vDSO code remove the
__vdso_gettimeofday and __vdso_clock_gettime symbols because
cntvct_functional() returns false since it does not match that
compatibility string.
Fixes: ecf99a439105 ("ARM: 8331/1: VDSO initialization, mapping, and synchronization")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d2ed69ce9ed3477e2a9527e6b89fe4689d99510e ]
a reserved field is used to signify prime physical function index
in the latest firmware version, so we must assign a value to it
correctly
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f596c87005f7b1baeb7d62d9a9e25d68c3dfae10 ]
As the description before netdev_run_todo, we cannot call free_netdev
before rtnl_unlock, fix it by reorder the code.
Signed-off-by: yangerkun <yangerkun@huawei.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fda31c50292a5062332fa0343c084bd9f46604d9 ]
When queueing a signal, we increment both the users count of pending
signals (for RLIMIT_SIGPENDING tracking) and we increment the refcount
of the user struct itself (because we keep a reference to the user in
the signal structure in order to correctly account for it when freeing).
That turns out to be fairly expensive, because both of them are atomic
updates, and particularly under extreme signal handling pressure on big
machines, you can get a lot of cache contention on the user struct.
That can then cause horrid cacheline ping-pong when you do these
multiple accesses.
So change the reference counting to only pin the user for the _first_
pending signal, and to unpin it when the last pending signal is
dequeued. That means that when a user sees a lot of concurrent signal
queuing - which is the only situation when this matters - the only
atomic access needed is generally the 'sigpending' count update.
This was noticed because of a particularly odd timing artifact on a
dual-socket 96C/192T Cascade Lake platform: when you get into bad
contention, on that machine for some reason seems to be much worse when
the contention happens in the upper 32-byte half of the cacheline.
As a result, the kernel test robot will-it-scale 'signal1' benchmark had
an odd performance regression simply due to random alignment of the
'struct user_struct' (and pointed to a completely unrelated and
apparently nonsensical commit for the regression).
Avoiding the double increments (and decrements on the dequeueing side,
of course) makes for much less contention and hugely improved
performance on that will-it-scale microbenchmark.
Quoting Feng Tang:
"It makes a big difference, that the performance score is tripled! bump
from original 17000 to 54000. Also the gap between 5.0-rc6 and
5.0-rc6+Jiri's patch is reduced to around 2%"
[ The "2% gap" is the odd cacheline placement difference on that
platform: under the extreme contention case, the effect of which half
of the cacheline was hot was 5%, so with the reduced contention the
odd timing artifact is reduced too ]
It does help in the non-contended case too, but is not nearly as
noticeable.
Reported-and-tested-by: Feng Tang <feng.tang@intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Huang, Ying <ying.huang@intel.com>
Cc: Philip Li <philip.li@intel.com>
Cc: Andi Kleen <andi.kleen@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 253216ffb2a002a682c6f68bd3adff5b98b71de8 ]
local->sta_mtx is held in __ieee80211_check_fast_rx_iface().
No need to use list_for_each_entry_rcu() as it also requires
a cond argument to avoid false lockdep warnings when not used in
RCU read-side section (with CONFIG_PROVE_RCU_LIST).
Therefore use list_for_each_entry();
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Link: https://lore.kernel.org/r/20200223143302.15390-1-madhuparnabhowmik10@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44343418d0f2f623cb9da6f5000df793131cbe3b ]
The KS8851 requires that packet RX and TX are mutually exclusive.
Currently, the driver hopes to achieve this by disabling interrupt
from the card by writing the card registers and by disabling the
interrupt on the interrupt controller. This however is racy on SMP.
Replace this approach by expanding the spinlock used around the
ks_start_xmit() TX path to ks_irq() RX path to assure true mutual
exclusion and remove the interrupt enabling/disabling, which is
now not needed anymore. Furthermore, disable interrupts also in
ks_net_stop(), which was missing before.
Note that a massive improvement here would be to re-use the KS8851
driver approach, which is to move the TX path into a worker thread,
interrupt handling to threaded interrupt, and synchronize everything
with mutexes, but that would be a much bigger rework, for a separate
patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eae7172f8141eb98e64e6e81acc9e9d5b2add127 ]
usbnet creates network interfaces with min_mtu = 0 and
max_mtu = ETH_MAX_MTU.
These values are not modified by qmi_wwan when the network interface
is created initially, allowing, for example, to set mtu greater than 1500.
When a raw_ip switch is done (raw_ip set to 'Y', then set to 'N') the mtu
values for the network interface are set through ether_setup, with
min_mtu = ETH_MIN_MTU and max_mtu = ETH_DATA_LEN, not allowing anymore to
set mtu greater than 1500 (error: mtu greater than device maximum).
The patch restores the original min/max mtu values set by usbnet after a
raw_ip switch.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff6993bb79b9f99bdac0b5378169052931b65432 ]
fc_disc_gpn_id_resp() should be the last function using it so free it here
to avoid memory leak.
Link: https://lore.kernel.org/r/1579013000-14570-2-git-send-email-igor.druzhinin@citrix.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7ee7d44b57c9ae174088e53a668852b7f4f452d ]
We may end up with a NULL reg_rule after the loop in
handle_channel_custom() if the bandwidth didn't fit,
check if this is the case and bail out if so.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200221104449.3b558a50201c.I4ad3725c4dacaefd2d18d3cc65ba6d18acd5dbfe@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be0aba826c4a6ba5929def1962a90d6127871969 ]
The Surfbook E11B uses the SIPODEV SP1064 touchpad, which does not supply
descriptors, so it has to be added to the override list.
BugLink: https://bugs.launchpad.net/bugs/1858299
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e433be929e63265b7412478eb7ff271467aee2d7 ]
Magic Keyboards with more recent firmware (0x0100) report Fn key differently.
Without this patch, Fn key may not behave as expected and may not be
configurable via hid_apple fnmode module parameter.
Signed-off-by: Mansour Behabadi <mansour@oxplot.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f9e12e0df012c4a9a7fd7eb0d3ae69b459d6b2c ]
In case the WDAT interface is broken, give the user an option to
ignore it to let a native driver bind to the watchdog device instead.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f967140dfb7442e2db0868b03b961f9c59418a1b ]
Enable the sampling check in kernel/events/core.c::perf_event_open(),
which returns the more appropriate -EOPNOTSUPP.
BEFORE:
$ sudo perf record -a -e instructions,l3_request_g1.caching_l3_cache_accesses true
Error:
The sys_perf_event_open() syscall returned with 22 (Invalid argument) for event (l3_request_g1.caching_l3_cache_accesses).
/bin/dmesg | grep -i perf may provide additional information.
With nothing relevant in dmesg.
AFTER:
$ sudo perf record -a -e instructions,l3_request_g1.caching_l3_cache_accesses true
Error:
l3_request_g1.caching_l3_cache_accesses: PMU Hardware doesn't support sampling/overflow-interrupts. Try 'perf stat'
Fixes: c43ca5091a37 ("perf/x86/amd: Add support for AMD NB and L2I "uncore" counters")
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20200311191323.13124-1-kim.phillips@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8e8ce08198de193e3d21d42e96945216e3d9ac7f upstream.
A transmission scheduling for an interface which is currently dropped by
batadv_iv_ogm_iface_disable could still be in progress. The B.A.T.M.A.N. V
is simply cancelling the workqueue item in an synchronous way but this is
not possible with B.A.T.M.A.N. IV because the OGM submissions are
intertwined.
Instead it has to stop submitting the OGM when it detect that the buffer
pointer is set to NULL.
Reported-by: syzbot+a98f2016f40b9cd3818a@syzkaller.appspotmail.com
Reported-by: syzbot+ac36b6a33c28a491e929@syzkaller.appspotmail.com
Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: Hillf Danton <hdanton@sina.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40e220b4218bb3d278e5e8cc04ccdfd1c7ff8307 upstream.
Each slave interface of an B.A.T.M.A.N. IV virtual interface has an OGM
packet buffer which is initialized using data from netdevice notifier and
other rtnetlink related hooks. It is sent regularly via various slave
interfaces of the batadv virtual interface and in this process also
modified (realloced) to integrate additional state information via TVLV
containers.
It must be avoided that the worker item is executed without a common lock
with the netdevice notifier/rtnetlink helpers. Otherwise it can either
happen that half modified/freed data is sent out or functions modifying the
OGM buffer try to access already freed memory regions.
Reported-by: syzbot+0cc629f19ccb8534935b@syzkaller.appspotmail.com
Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
