IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 7e842d70fe599bc13594b650b2144c4b6e6d6bf1 ]
HyperFlash devices fail to probe:
rpc-if-hyperflash rpc-if-hyperflash: probing of hyperbus device failed
In HyperFlash or Octal-SPI Flash mode, the Transfer Data Enable bits
(SPIDE) in the Manual Mode Enable Setting Register (SMENR) are derived
from half of the transfer size, cfr. the rpcif_bits_set() helper
function. However, rpcif_reg_{read,write}() does not take the bus size
into account, and does not double all Manual Mode Data Register access
sizes when communicating with a HyperFlash or Octal-SPI Flash device.
Fix this, and avoid the back-and-forth conversion between transfer size
and Transfer Data Enable bits, by explicitly storing the transfer size
in struct rpcif, and using that value to determine access size in
rpcif_reg_{read,write}().
Enforce that the "high" Manual Mode Read/Write Data Registers
(SM[RW]DR1) are only used for 8-byte data accesses.
While at it, forbid writing to the Manual Mode Read Data Registers,
as they are read-only.
Fixes: fff53a551db50f5e ("memory: renesas-rpc-if: Correct QSPI data transfer in Manual mode")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/cde9bfacf704c81865f57b15d1b48a4793da4286.1649681476.git.geert+renesas@glider.be
Link: https://lore.kernel.org/r/20220420070526.9367-1-krzysztof.kozlowski@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e74200ebf7c4f6a7a7d1be9f63833ddba251effa ]
The stm32_gpio_get() should only be called for LEVEL triggered interrupts,
skip calling it for EDGE triggered interrupts altogether to avoid wasting
CPU cycles in EOI handler. On this platform, EDGE triggered interrupts are
the majority and LEVEL triggered interrupts are the exception no less, and
the CPU cycles are not abundant.
Fixes: 47beed513a85b ("pinctrl: stm32: Add level interrupt support to gpio irq chip")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Fabien Dessenne <fabien.dessenne@foss.st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-arm-kernel@lists.infradead.org
To: linux-gpio@vger.kernel.org
Link: https://lore.kernel.org/r/20220415215410.498349-1-marex@denx.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37c5f9e80e015d0df17d0c377c18523002986851 ]
Commit 46b5889cc2c5 ("mtd: implement proper partition handling")
started using "mtd_get_master_ofs()" in mtd callbacks to determine
memory offsets by means of 'part' field from mtd_info, what previously
was smashed accessing 'master' field in the mtd_set_dev_defaults() method.
That provides wrong offset what causes hardware access errors.
Just make 'part', 'master' as separate fields, rather than using
union type to avoid 'part' data corruption when mtd_set_dev_defaults()
is called.
Fixes: 46b5889cc2c5 ("mtd: implement proper partition handling")
Signed-off-by: Oleksandr Ocheretnyi <oocheret@cisco.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220417184649.449289-1-oocheret@cisco.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 084c16ab423a8890121b902b405823bfec5b4365 ]
wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.
Fixes: 83738d87e3a0 ("mtd: sh_flctl: Add DMA capabilty")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412083435.29254-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87950929e2ff2236207bdbe14bff8230558b541b ]
If EINT_MTK is m and PINCTRL_MTK_V2 is y, build fails:
drivers/pinctrl/mediatek/pinctrl-moore.o: In function `mtk_gpio_set_config':
pinctrl-moore.c:(.text+0xa6c): undefined reference to `mtk_eint_set_debounce'
drivers/pinctrl/mediatek/pinctrl-moore.o: In function `mtk_gpio_to_irq':
pinctrl-moore.c:(.text+0xacc): undefined reference to `mtk_eint_find_irq'
Select EINT_MTK for PINCTRL_MTK_V2 to fix this.
Fixes: 8174a8512e3e ("pinctrl: mediatek: make MediaTek pinctrl v2 driver ready for buidling loadable module")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20220409105958.37412-1-yuehaibing@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c8045d48dee703ad8eab2be7d6547765a89c069 ]
If clk_prepare_enable() fails we call clk_disable_unprepare()
in the error path what results in a warning that the clock
is disabled and unprepared already.
And if we fail later in phy_g12a_usb3_pcie_probe() then we
bail out w/o calling clk_disable_unprepare().
This patch fixes both errors.
Fixes: 36077e16c050 ("phy: amlogic: Add Amlogic G12A USB3 + PCIE Combo PHY Driver")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/8e416f95-1084-ee28-860e-7884f7fa2e32@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eba1a872cb73314280d5448d934935b23e30b7ca ]
The memory size of ip_vs_conn_tab changed after we use hlist
instead of list.
Fixes: 731109e78415 ("ipvs: use hlist instead of list")
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46ff3df87215ff42c0cd2c4bdb7d74540384a69c ]
The pinout of the OMAP35 and DM37 variants of the SOM-LV are the
same, but the macros which define the pinmuxing are different
between OMAP3530 and DM3730. The pinmuxing was correct for
for the DM3730, but wrong for the OMAP3530. Since the boot loader
was correctly pin-muxing the pins, this was not obvious. As the
bootloader not guaranteed to pinmux all the pins any more, this
causes an issue, so the pinmux needs to be moved from a common
file to their respective board files.
Fixes: f8a2e3ff7103 ("ARM: dts: Add minimal support for LogicPD OMAP35xx SOM-LV devkit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Message-Id: <20220303171818.11060-1-aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 942da3af32b2288e674736eb159d1fc676261691 ]
The bootloader for the AM3517 has previously done much of the pin
muxing, but as the bootloader is moving more and more to a model
based on the device tree, it may no longer automatically mux the
pins, so it is necessary to add the pinmuxing to the Linux device
trees so the respective peripherals can remain functional.
Fixes: 6ed1d7997561 ("ARM: dts: am3517-evm: Add support for UI board and Audio")
Signed-off-by: Adam Ford <aford173@gmail.com>
Message-Id: <20220226214820.747847-1-aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09269dd050094593fc747f2a5853d189fefcb6b5 ]
Commit a1ebdb374199 ("ARM: dts: Fix swapped mmc order for omap3")
introduces general mmc aliases. Let's tailor them to the need
of the GTA04 board which does not make use of mmc2 and mmc3 interfaces.
Fixes: a1ebdb374199 ("ARM: dts: Fix swapped mmc order for omap3")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Message-Id: <dc9173ee3d391d9e92b7ab8ed4f84b29f0a21c83.1646744420.git.hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fb251c265608636fc961b7d38e1a03937e57371 ]
Similar to the sc7180 commit, let's drop the IP0 interconnects here
because the IP0 resource is also used in the clk-rpmh driver on sdx55.
It's bad to have the clk framework and interconnect framework control
the same RPMh resource without any coordination. The rpmh driver in the
kernel doesn't aggregate resources between clients either, so leaving
control to clk-rpmh avoids any issues with unused interconnects turning
off IP0 behind the back of the clk framework.
Cc: Alex Elder <elder@linaro.org>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Taniya Das <quic_tdas@quicinc.com>
Cc: Mike Tipton <quic_mdtipton@quicinc.com>
Fixes: b2150cab9a97 ("clk: qcom: rpmh: add support for SDX55 rpmh IPA clock")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220412220033.1273607-3-swboyd@chromium.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce88613e5bd579478653a028291098143f2a5bdf ]
The pm_runtime_enable() will increase power disable depth.
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable().
Add missing pm_runtime_disable() for serdes_am654_probe().
Fixes: 71e2f5c5c224 ("phy: ti: Add a new SERDES driver for TI's AM654x SoC")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220301025853.1911-1-linmq006@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d644e0d79829b1b9a14beedbdb0dc1256fc3677d ]
The pm_runtime_enable will increase power disable depth.
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable(). And use pm_runtime_dont_use_autosuspend() to
undo pm_runtime_use_autosuspend()
In the PM Runtime docs:
Drivers in ->remove() callback should undo the runtime PM changes done
in ->probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc.
We should do this in error handling.
Fixes: f7f50b2a7b05 ("phy: mapphone-mdm6600: Add runtime PM support for n_gsm on USB suspend")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220301024615.31899-1-linmq006@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c640d9544d0109da3889d71ae77301e556db977 ]
Commit bf781869e5cf ("ARM: dts: at91: add pinctrl-{names, 0} for all
gpios") introduces pinctrl phandles for pins used by individual
controllers to avoid failures due to commit 2ab73c6d8323 ("gpio:
Support GPIO controllers without pin-ranges"). For SPI controllers
available on SAMA5D4 and SAMA5D3 some of the pins are defined in
SoC specific dtsi on behalf of pinctrl-0. Adding extra pinctrl phandles
on board specific dts also on behalf of pinctrl-0 overwrite the pinctrl-0
phandle specified in SoC specific dtsi. Thus add the board specific
pinctrl to pinctrl-1.
Fixes: bf781869e5cf ("ARM: dts: at91: add pinctrl-{names, 0} for all gpios")
Depends-on: 5c8b49852910 ("ARM: dts: at91: sama5d4_xplained: fix pinctrl phandle name")
Reported-by: Ajay Kathat <ajay.kathat@microchip.com>
Co-developed-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Ajay Kathat <ajay.kathat@microchip.com>
Tested-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220331141323.194355-2-claudiu.beznea@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c8b49852910caffeebb1ce541fdd264ffc691b8 ]
Pinctrl phandle is for spi1 so rename it to reflect this.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220331141323.194355-1-claudiu.beznea@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e486fe341fabd8e583f3d601a874cd394979c45 ]
The MCLK of the WM8731 on the AT91SAM9G20-EK board is connected to the
PCK0 output of the SoC and is expected to be set to 12MHz. Previously
this was mapped using pre-common clock API calls in the audio machine
driver but the conversion to the common clock framework broke that so
describe things in the DT instead.
Fixes: ff78a189b0ae55f ("ARM: at91: remove old at91-specific clock driver")
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220404102806.581374-2-broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3588060befff75ff39fab7122b94c6fb3148fcda ]
The corresponding API for clk_prepare_enable is clk_disable_unprepare.
Make sure that the clock is unprepared on exit by changing clk_disable
to clk_disable_unprepare.
Fixes: ed31ee7cf1fe ("phy: ti: usb2: Fix logic on -EPROBE_DEFER")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220318105748.19532-1-linmq006@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d2453d9a307c2eafd21242dd73f35f05fb7ce74 ]
We currently are getting the following warning after a system suspend:
Powerdomain (vpe_pwrdm) didn't enter target state 0
Looks like this is because the STANDBYMODE bit for SMART_IDLE should
not be used. The TRM "Table 12-348. VPE_SYSCONFIG" says that the value
for SMART_IDLE is "0x2: Same behavior as bit-field value of 0x1". But
if the SMART_IDLE value is used, PM_VPE_PWRSTST LASTPOWERSTATEENTERED
bits always show value of 3.
Let's fix the issue by dropping SMART_IDLE for vpe. And let's also add
the missing the powerdomain for vpe.
Fixes: 1a2095160594 ("ARM: dts: dra7: Add ti-sysc node for VPE")
Cc: Benoit Parrot <bparrot@ti.com>
Reported-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a12315d6d27093392b6c634e1d35a59f1d1f7a59 ]
On beagleboard revisions A to B4 we need to use gpt12 as the system timer.
However, the quirk handling added for gpt12 caused a regression for system
suspend for am335x as the PM coprocessor needs the timers idled for
suspend.
Let's make the gpt12 quirk specific to omap34xx, other SoCs don't need
it. Beagleboard revisions C and later no longer need to use the gpt12
related quirk. Then at some point, if we decide to drop support for the old
beagleboard revisions A to B4, we can also drop the gpt12 related quirks
completely.
Fixes: 3ff340e24c9d ("bus: ti-sysc: Fix gpt12 system timer issue with reserved status")
Reported-by: Kevin Hilman <khilman@baylibre.com>
Suggested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f83e6b4161617014017a694888dd8743f46f071 ]
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
Fixes: fd1c07861491 ("ARM: OMAP4: Fix the init code to have OMAP4460 errata available in DT build")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <20220309104302.18398-1-linmq006@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c8402c4db45dd55c2c93c8d730f5dfa7c78a702 ]
The actions of of_find_i2c_device_by_node() in probe function should be
reversed in error paths by putting the reference to obtained device.
Fixes: bcff4cba41bc ("PHY: Exynos: Add Exynos5250 SATA PHY driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20220407091857.230386-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 388ec8f079f2f20d5cd183c3bc6f33cbc3ffd3ef ]
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes: bcff4cba41bc ("PHY: Exynos: Add Exynos5250 SATA PHY driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220407091857.230386-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 962dd65e575dde950ef0844568edc37cfb39f302 ]
The labels for lines 61 through 84 on the periphs-banks were offset by 2.
2 lines are missing in the BOOT GPIO lines (contains 14, should be 16)
Added 2 empty entries in BOOT to realigned the rest of GPIO labels
to match the Banana Pi M5 schematics.
(Thanks to Neil Armstrong for the heads up on the position of the missing pins)
Fixes: 976e920183e4 ("arm64: dts: meson-sm1: add Banana PI BPI-M5 board dts")
Signed-off-by: Guillaume Giraudon <ggiraudon@prism19.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220411144427.874-1-ggiraudon@prism19.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 574518b7ccbaef74cb89eb1a1a0da88afa1e0113 ]
The most specific compatible string element should be "fsl,imx8mn-sai"
on i.MX8M Nano, fix it from current "fsl,imx8mm-sai" (two Ms, likely
due to copy-paste error from i.MX8M Mini).
Fixes: 9e9860069725f ("arm64: dts: imx8mn: Add SAI nodes")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa51e1dc4b91375bc18349663a52395ad585bd3c ]
On a custom carrier board with a i.MX6Q Apalis SoM, the sgtl5000 codec
on the SoM is often not detected and the following error message is
seen when the sgtl5000 driver tries to read the ID register:
sgtl5000 1-000a: Error reading chip id -6
The reason for the error is that the MCLK clock is not provided
early enough.
Fix the problem by describing the MCLK pinctrl inside the codec
node instead of placing it inside the audmux pinctrl group.
With this change applied the sgtl5000 is always detected on every boot.
Fixes: 693e3ffaae5a ("ARM: dts: imx6: Add support for Toradex Apalis iMX6Q/D SoM")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e91ac20889d1a26d077cc511365cd7ff4346a6f3 ]
In some situations software handles TRB events slower than adding TRBs.
If the number of TRB events to be processed in a given interrupt is exactly
the same as the event ring size 256, then the local variable
"event_ring_deq" that holds the initial dequeue position is equal to
software_dequeue after handling all 256 interrupts.
It will cause driver to not update ERDP to hardware,
Software dequeue pointer is out of sync with ERDP on interrupt exit.
On the next interrupt, the event ring may full but driver will not
update ERDP as software_dequeue is equal to ERDP.
[ 536.377115] xhci_hcd 0000:00:12.0: ERROR unknown event type 37
[ 566.933173] sd 8:0:0:0: [sdb] tag#27 uas_eh_abort_handler 0 uas-tag 7 inflight: CMD OUT
[ 566.933181] sd 8:0:0:0: [sdb] tag#27 CDB: Write(10) 2a 00 17 71 e6 78 00 00 08 00
[ 572.041186] xhci_hcd On some situataions,the0000:00:12.0: xHCI host not responding to stop endpoint command.
[ 572.057193] xhci_hcd 0000:00:12.0: Host halt failed, -110
[ 572.057196] xhci_hcd 0000:00:12.0: xHCI host controller not responding, assume dead
[ 572.057236] sd 8:0:0:0: [sdb] tag#26 uas_eh_abort_handler 0 uas-tag 6 inflight: CMD
[ 572.057240] sd 8:0:0:0: [sdb] tag#26 CDB: Write(10) 2a 00 38 eb cc d8 00 00 08 00
[ 572.057244] sd 8:0:0:0: [sdb] tag#25 uas_eh_abort_handler 0 uas-tag 5 inflight: CMD
Hardware ERDP is updated mid event handling if there are more than 128
events in an interrupt (half of ring size).
Fix this by updating the software local variable at the same time as
hardware ERDP.
[commit message rewording -Mathias]
Fixes: dc0ffbea5729 ("usb: host: xhci: update event ring dequeue pointer on purpose")
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220408134823.2527272-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd2737fab4a6ce9ba4eb84842bedbd87d55241a6 ]
The fsl,scu.txt dt-binding documentation explicitly mentions
that the compatible string should be either "fsl,imx8qm-clock"
or "fsl,imx8qxp-clock", followed by "fsl,scu-clk". Also, i.MX8qm
SCU clocks and i.MX8qxp SCU clocks are really not the same, so
we have to set the compatible property according to SoC name.
Let's correct the i.MX8qm clock controller's compatible property
from
"fsl,imx8qxp-clk", "fsl,scu-clk"
to
"fsl,imx8qm-clk", "fsl,scu-clk" .
Fixes: f2180be18a63 ("arm64: dts: imx: add imx8qm common dts file")
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8de8b71b787f38983d414d2dba169a3bfefa668a ]
While checking AF_XDP copy mode combined with busy poll, strange
results were observed. rxdrop and txonly scenarios worked fine, but
l2fwd broke immediately.
After a deeper look, it turned out that for l2fwd, Tx side was exiting
early due to xsk_no_wakeup() returning true and in the end
xsk_generic_xmit() was never called. Note that AF_XDP Tx in copy mode
is syscall steered, so the current behavior is broken.
Txonly scenario only worked due to the fact that
sk_mark_napi_id_once_xdp() was never called - since Rx side is not in
the picture for this case and mentioned function is called in
xsk_rcv_check(), sk::sk_napi_id was never set, which in turn meant that
xsk_no_wakeup() was returning false (see the sk->sk_napi_id >=
MIN_NAPI_ID check in there).
To fix this, prefer busy poll in xsk_sendmsg() only when zero copy is
enabled on a given AF_XDP socket. By doing so, busy poll in copy mode
would not exit early on Tx side and eventually xsk_generic_xmit() will
be called.
Fixes: a0731952d9cd ("xsk: Add busy-poll support for {recv,send}msg()")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220406155804.434493-1-maciej.fijalkowski@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fe4e0d3cbfe90152137963cc024ecb63db6e8e6 ]
According to the datasheet, mt7622 only has 5 ECC capabilities instead
of 7, and the decoding error register is arranged as follows:
+------+---------+---------+---------+---------+
| Bits | 19:15 | 14:10 | 9:5 | 4:0 |
+------+---------+---------+---------+---------+
| Name | ERRNUM3 | ERRNUM2 | ERRNUM1 | ERRNUM0 |
+------+---------+---------+---------+---------+
This means err_mask should be 0x1f instead of 0x3f and the number of
bits shifted in mtk_ecc_get_stats should be 5 instead of 8.
This commit introduces err_shift for the difference in this register
and fix other existing parameters.
Public MT7622 reference manual can be found on [0] and the info this
commit is based on is from page 656 and page 660.
[0]: https://wiki.banana-pi.org/Banana_Pi_BPI-R64#Documents
Fixes: 98dea8d71931 ("mtd: nand: mtk: Support MT7622 NAND flash controller.")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220402160315.919094-1-gch981213@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd86d85401c2049f652293877c0f7e6e5afc3bbc ]
Amlogic SM1 devices experience CPU stalls and random board wedges when
the system idles and CPU cores clock down to lower opp points. Recent
vendor kernels include a change to remove 100-250MHz and other distro
sources also remove the 500/667MHz points. Unless all 100-667Mhz opps
are removed or the CPU governor forced to performance stalls are still
observed, so let's remove them to improve stability and uptime.
Fixes: 3d9e76483049 ("arm64: dts: meson-sm1-sei610: enable DVFS")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220210100638.19130-3-christianshewitt@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c4d636bc00dc17c63ffb2a73a0da850240e26e3 ]
Amlogic G12B devices experience CPU stalls and random board wedges when
the system idles and CPU cores clock down to lower opp points. Recent
vendor kernels include a change to remove 100-250MHz and other distro
sources also remove the 500/667MHz points. Unless all 100-667Mhz opps
are removed or the CPU governor forced to performance stalls are still
observed, so let's remove them to improve stability and uptime.
Fixes: b96d4e92709b ("arm64: dts: meson-g12b: support a311d and s922x cpu operating points")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220210100638.19130-2-christianshewitt@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f84ccad5f5660f86a642a3d7e2bfdc4e7a8a2d49 ]
On QCOM platforms with EPSS flavour of cpufreq IP a throttled frequency is
obtained from another register REG_DOMAIN_STATE, thus the helper function
qcom_lmh_get_throttle_freq() should be modified accordingly, as for now
it returns gibberish since .reg_current_vote is unset for EPSS hardware.
To exclude a hardcoded magic number 19200 it is replaced by "xo" clock rate
in KHz.
Fixes: 275157b367f4 ("cpufreq: qcom-cpufreq-hw: Add dcvs interrupt support")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit acb16b395c3f3d7502443e0c799c2b42df645642 upstream.
We received a report[1] of kernel crashes when Cilium is used in XDP
mode with virtio_net after updating to newer kernels. After
investigating the reason it turned out that when using mergeable bufs
with an XDP program which adjusts xdp.data or xdp.data_meta page_to_buf()
calculates the build_skb address wrong because the offset can become less
than the headroom so it gets the address of the previous page (-X bytes
depending on how lower offset is):
page_to_skb: page addr ffff9eb2923e2000 buf ffff9eb2923e1ffc offset 252 headroom 256
This is a pr_err() I added in the beginning of page_to_skb which clearly
shows offset that is less than headroom by adding 4 bytes of metadata
via an xdp prog. The calculations done are:
receive_mergeable():
headroom = VIRTIO_XDP_HEADROOM; // VIRTIO_XDP_HEADROOM == 256 bytes
offset = xdp.data - page_address(xdp_page) -
vi->hdr_len - metasize;
page_to_skb():
p = page_address(page) + offset;
...
buf = p - headroom;
Now buf goes -4 bytes from the page's starting address as can be seen
above which is set as skb->head and skb->data by build_skb later. Depending
on what's done with the skb (when it's freed most often) we get all kinds
of corruptions and BUG_ON() triggers in mm[2]. We have to recalculate
the new headroom after the xdp program has run, similar to how offset
and len are recalculated. Headroom is directly related to
data_hard_start, data and data_meta, so we use them to get the new size.
The result is correct (similar pr_err() in page_to_skb, one case of
xdp_page and one case of virtnet buf):
a) Case with 4 bytes of metadata
[ 115.949641] page_to_skb: page addr ffff8b4dcfad2000 offset 252 headroom 252
[ 121.084105] page_to_skb: page addr ffff8b4dcf018000 offset 20732 headroom 252
b) Case of pushing data +32 bytes
[ 153.181401] page_to_skb: page addr ffff8b4dd0c4d000 offset 288 headroom 288
[ 158.480421] page_to_skb: page addr ffff8b4dd00b0000 offset 24864 headroom 288
c) Case of pushing data -33 bytes
[ 835.906830] page_to_skb: page addr ffff8b4dd3270000 offset 223 headroom 223
[ 840.839910] page_to_skb: page addr ffff8b4dcdd68000 offset 12511 headroom 223
Offset and headroom are equal because offset points to the start of
reserved bytes for the virtio_net header which are at buf start +
headroom, while data points at buf start + vnet hdr size + headroom so
when data or data_meta are adjusted by the xdp prog both the headroom size
and the offset change equally. We can use data_hard_start to compute the
new headroom after the xdp prog (linearized / page start case, the
virtnet buf case is similar just with bigger base offset):
xdp.data_hard_start = page_address + vnet_hdr
xdp.data = page_address + vnet_hdr + headroom
new headroom after xdp prog = xdp.data - xdp.data_hard_start - metasize
An example reproducer xdp prog[3] is below.
[1] https://github.com/cilium/cilium/issues/19453
[2] Two of the many traces:
[ 40.437400] BUG: Bad page state in process swapper/0 pfn:14940
[ 40.916726] BUG: Bad page state in process systemd-resolve pfn:053b7
[ 41.300891] kernel BUG at include/linux/mm.h:720!
[ 41.301801] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[ 41.302784] CPU: 1 PID: 1181 Comm: kubelet Kdump: loaded Tainted: G B W 5.18.0-rc1+ #37
[ 41.304458] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1.fc35 04/01/2014
[ 41.306018] RIP: 0010:page_frag_free+0x79/0xe0
[ 41.306836] Code: 00 00 75 ea 48 8b 07 a9 00 00 01 00 74 e0 48 8b 47 48 48 8d 50 ff a8 01 48 0f 45 fa eb d0 48 c7 c6 18 b8 30 a6 e8 d7 f8 fc ff <0f> 0b 48 8d 78 ff eb bc 48 8b 07 a9 00 00 01 00 74 3a 66 90 0f b6
[ 41.310235] RSP: 0018:ffffac05c2a6bc78 EFLAGS: 00010292
[ 41.311201] RAX: 000000000000003e RBX: 0000000000000000 RCX: 0000000000000000
[ 41.312502] RDX: 0000000000000001 RSI: ffffffffa6423004 RDI: 00000000ffffffff
[ 41.313794] RBP: ffff993c98823600 R08: 0000000000000000 R09: 00000000ffffdfff
[ 41.315089] R10: ffffac05c2a6ba68 R11: ffffffffa698ca28 R12: ffff993c98823600
[ 41.316398] R13: ffff993c86311ebc R14: 0000000000000000 R15: 000000000000005c
[ 41.317700] FS: 00007fe13fc56740(0000) GS:ffff993cdd900000(0000) knlGS:0000000000000000
[ 41.319150] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 41.320152] CR2: 000000c00008a000 CR3: 0000000014908000 CR4: 0000000000350ee0
[ 41.321387] Call Trace:
[ 41.321819] <TASK>
[ 41.322193] skb_release_data+0x13f/0x1c0
[ 41.322902] __kfree_skb+0x20/0x30
[ 41.343870] tcp_recvmsg_locked+0x671/0x880
[ 41.363764] tcp_recvmsg+0x5e/0x1c0
[ 41.384102] inet_recvmsg+0x42/0x100
[ 41.406783] ? sock_recvmsg+0x1d/0x70
[ 41.428201] sock_read_iter+0x84/0xd0
[ 41.445592] ? 0xffffffffa3000000
[ 41.462442] new_sync_read+0x148/0x160
[ 41.479314] ? 0xffffffffa3000000
[ 41.496937] vfs_read+0x138/0x190
[ 41.517198] ksys_read+0x87/0xc0
[ 41.535336] do_syscall_64+0x3b/0x90
[ 41.551637] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 41.568050] RIP: 0033:0x48765b
[ 41.583955] Code: e8 4a 35 fe ff eb 88 cc cc cc cc cc cc cc cc e8 fb 7a fe ff 48 8b 7c 24 10 48 8b 74 24 18 48 8b 54 24 20 48 8b 44 24 08 0f 05 <48> 3d 01 f0 ff ff 76 20 48 c7 44 24 28 ff ff ff ff 48 c7 44 24 30
[ 41.632818] RSP: 002b:000000c000a2f5b8 EFLAGS: 00000212 ORIG_RAX: 0000000000000000
[ 41.664588] RAX: ffffffffffffffda RBX: 000000c000062000 RCX: 000000000048765b
[ 41.681205] RDX: 0000000000005e54 RSI: 000000c000e66000 RDI: 0000000000000016
[ 41.697164] RBP: 000000c000a2f608 R08: 0000000000000001 R09: 00000000000001b4
[ 41.713034] R10: 00000000000000b6 R11: 0000000000000212 R12: 00000000000000e9
[ 41.728755] R13: 0000000000000001 R14: 000000c000a92000 R15: ffffffffffffffff
[ 41.744254] </TASK>
[ 41.758585] Modules linked in: br_netfilter bridge veth netconsole virtio_net
and
[ 33.524802] BUG: Bad page state in process systemd-network pfn:11e60
[ 33.528617] page ffffe05dc0147b00 ffffe05dc04e7a00 ffff8ae9851ec000 (1) len 82 offset 252 metasize 4 hroom 0 hdr_len 12 data ffff8ae9851ec10c data_meta ffff8ae9851ec108 data_end ffff8ae9851ec14e
[ 33.529764] page:000000003792b5ba refcount:0 mapcount:-512 mapping:0000000000000000 index:0x0 pfn:0x11e60
[ 33.532463] flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff)
[ 33.532468] raw: 000fffffc0000000 0000000000000000 dead000000000122 0000000000000000
[ 33.532470] raw: 0000000000000000 0000000000000000 00000000fffffdff 0000000000000000
[ 33.532471] page dumped because: nonzero mapcount
[ 33.532472] Modules linked in: br_netfilter bridge veth netconsole virtio_net
[ 33.532479] CPU: 0 PID: 791 Comm: systemd-network Kdump: loaded Not tainted 5.18.0-rc1+ #37
[ 33.532482] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1.fc35 04/01/2014
[ 33.532484] Call Trace:
[ 33.532496] <TASK>
[ 33.532500] dump_stack_lvl+0x45/0x5a
[ 33.532506] bad_page.cold+0x63/0x94
[ 33.532510] free_pcp_prepare+0x290/0x420
[ 33.532515] free_unref_page+0x1b/0x100
[ 33.532518] skb_release_data+0x13f/0x1c0
[ 33.532524] kfree_skb_reason+0x3e/0xc0
[ 33.532527] ip6_mc_input+0x23c/0x2b0
[ 33.532531] ip6_sublist_rcv_finish+0x83/0x90
[ 33.532534] ip6_sublist_rcv+0x22b/0x2b0
[3] XDP program to reproduce(xdp_pass.c):
#include <linux/bpf.h>
#include <bpf/bpf_helpers.h>
SEC("xdp_pass")
int xdp_pkt_pass(struct xdp_md *ctx)
{
bpf_xdp_adjust_head(ctx, -(int)32);
return XDP_PASS;
}
char _license[] SEC("license") = "GPL";
compile: clang -O2 -g -Wall -target bpf -c xdp_pass.c -o xdp_pass.o
load on virtio_net: ip link set enp1s0 xdpdrv obj xdp_pass.o sec xdp_pass
CC: stable@vger.kernel.org
CC: Jason Wang <jasowang@redhat.com>
CC: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
CC: Daniel Borkmann <daniel@iogearbox.net>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: virtualization@lists.linux-foundation.org
Fixes: 8fb7da9e9907 ("virtio_net: get build_skb() buf by data ptr")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20220425103703.3067292-1-razor@blackwall.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c936f9ea11ec4e35e288810a7503b5c841a355f upstream.
When an iocg is in debt, its inuse weight is owned by debt handling and
should stay at 1. This invariant was broken when determining the amount of
surpluses at the beginning of donation calculation - when an iocg's
hierarchical weight is too low, the iocg is excluded from donation
calculation and its inuse is reset to its active regardless of its
indebtedness, triggering warnings like the following:
WARNING: CPU: 5 PID: 0 at block/blk-iocost.c:1416 iocg_kick_waitq+0x392/0x3a0
...
RIP: 0010:iocg_kick_waitq+0x392/0x3a0
Code: 00 00 be ff ff ff ff 48 89 4d a8 e8 98 b2 70 00 48 8b 4d a8 85 c0 0f 85 4a fe ff ff 0f 0b e9 43 fe ff ff 0f 0b e9 4d fe ff ff <0f> 0b e9 50 fe ff ff e8 a2 ae 70 00 66 90 0f 1f 44 00 00 55 48 89
RSP: 0018:ffffc90000200d08 EFLAGS: 00010016
...
<IRQ>
ioc_timer_fn+0x2e0/0x1470
call_timer_fn+0xa1/0x2c0
...
As this happens only when an iocg's hierarchical weight is negligible, its
impact likely is limited to triggering the warnings. Fix it by skipping
resetting inuse of under-weighted debtors.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Rik van Riel <riel@surriel.com>
Fixes: c421a3eb2e27 ("blk-iocost: revamp debt handling")
Cc: stable@vger.kernel.org # v5.10+
Link: https://lore.kernel.org/r/YmjODd4aif9BzFuO@slm.duckdns.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e0815b3e09986d2fe651199363e135b9358132a upstream.
When a XEN_HVM guest uses the XEN PIRQ/Eventchannel mechanism, then
PCI/MSI[-X] masking is solely controlled by the hypervisor, but contrary to
XEN_PV guests this does not disable PCI/MSI[-X] masking in the PCI/MSI
layer.
This can lead to a situation where the PCI/MSI layer masks an MSI[-X]
interrupt and the hypervisor grants the write despite the fact that it
already requested the interrupt. As a consequence interrupt delivery on the
affected device is not happening ever.
Set pci_msi_ignore_mask to prevent that like it's done for XEN_PV guests
already.
Fixes: 809f9267bbab ("xen: map MSIs into pirqs")
Reported-by: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com>
Reported-by: Dusty Mabe <dustymabe@redhat.com>
Reported-by: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Noah Meyerhans <noahm@debian.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87tuaduxj5.ffs@tglx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ec1442953c66a1d8462cccd8c20b7ba561f5915 upstream.
These patch_text implementations are using stop_machine_cpuslocked
infrastructure with atomic cpu_count. The original idea: When the
master CPU patch_text, the others should wait for it. But current
implementation is using the first CPU as master, which couldn't
guarantee the remaining CPUs are waiting. This patch changes the
last CPU as the master to solve the potential risk.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Fixes: 043cb41a85de ("riscv: introduce interfaces to patch kernel code")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4d8a29997731b3bb14059024b24df9f784288d0 upstream.
If we pass too short string to "hex2bin" (and the string size without
the terminating NUL character is even), "hex2bin" reads one byte after
the terminating NUL character. This patch fixes it.
Note that hex_to_bin returns -1 on error and hex2bin return -EINVAL on
error - so we can't just return the variable "hi" or "lo" on error.
This inconsistency may be fixed in the next merge window, but for the
purpose of fixing this bug, we just preserve the existing behavior and
return -1 and -EINVAL.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Fixes: b78049831ffe ("lib: add error checking to hex2bin")
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5be15767e7e284351853cbaba80cde8620341fb upstream.
The function hex2bin is used to load cryptographic keys into device
mapper targets dm-crypt and dm-integrity. It should take constant time
independent on the processed data, so that concurrently running
unprivileged code can't infer any information about the keys via
microarchitectural convert channels.
This patch changes the function hex_to_bin so that it contains no
branches and no memory accesses.
Note that this shouldn't cause performance degradation because the size
of the new function is the same as the size of the old function (on
x86-64) - and the new function causes no branch misprediction penalties.
I compile-tested this function with gcc on aarch64 alpha arm hppa hppa64
i386 ia64 m68k mips32 mips64 powerpc powerpc64 riscv sh4 s390x sparc32
sparc64 x86_64 and with clang on aarch64 arm hexagon i386 mips32 mips64
powerpc powerpc64 s390x sparc32 sparc64 x86_64 to verify that there are
no branches in the generated code.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac875df4d854ab13d9c4af682a1837a1214fecec upstream.
The Samsung pinctrl drivers depend on OF_GPIO, which is part of GPIOLIB.
ARMv7 Exynos platform selects GPIOLIB and Samsung pinctrl drivers. ARMv8
Exynos selects only the latter leading to possible wrong configuration
on ARMv8 build:
WARNING: unmet direct dependencies detected for PINCTRL_EXYNOS
Depends on [n]: PINCTRL [=y] && OF_GPIO [=n] && (ARCH_EXYNOS [=y] || ARCH_S5PV210 || COMPILE_TEST [=y])
Selected by [y]:
- ARCH_EXYNOS [=y]
Always select the GPIOLIB from the Samsung pinctrl drivers to fix the
issue. This requires removing of OF_GPIO dependency (to avoid recursive
dependency), so add dependency on OF for COMPILE_TEST cases.
Reported-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Fixes: eed6b3eb20b9 ("arm64: Split out platform options to separate Kconfig")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220420141407.470955-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc900431337f5f861e3cc47ec5be5a69db40ee34 upstream.
Due to what looks like a copy-paste error, the ECSPI2_MISO pad is not
muxed for SPI mode and causes reads from a slave-device connected to the
SPI header to always return zero.
Configure the ECSPI2_MISO pad for SPI mode on the gw71xx, gw72xx and
gw73xx families of boards that got this wrong.
Fixes: 6f30b27c5ef5 ("arm64: dts: imx8mm: Add Gateworks i.MX 8M Mini Development Kits")
Cc: stable@vger.kernel.org # 5.12
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c38f83bae4037023827c85e045841d0421f85034 upstream.
It is possible that the recovery work might be running while the freeze
gets executed (during hibernation etc.,). Currently, we don't powerdown
the stack if it is not up but if the recovery work completes after freeze,
then the device will be up afterwards. This will not be a sane situation.
So let's flush the recovery worker before trying to powerdown the device.
Cc: stable@vger.kernel.org
Fixes: 5f0c2ee1fe8d ("bus: mhi: pci-generic: Fix hibernation")
Reported-by: Bhaumik Vasav Bhatt <quic_bbhatt@quicinc.com>
Reviewed-by: Bhaumik Vasav Bhatt <quic_bbhatt@quicinc.com>
Link: https://lore.kernel.org/r/20220408150039.17297-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e64d5fa5044f225ac87d96a7e4be11389999c4c6 upstream.
During hibernation process, once thaw() stage completes, the MHI endpoint
devices will be in M0 state post recovery. After that, the devices will be
powered down so that the system can enter the target sleep state. During
this stage, the PCI core will put the devices in D3hot. But this transition
is allowed by the MHI spec. The devices can only enter D3hot when it is in
M3 state.
So for fixing this issue, let's add the poweroff() callback that will get
executed before putting the system in target sleep state during
hibernation. This callback will power down the device properly so that it
could be restored during restore() or thaw() stage.
Cc: stable@vger.kernel.org
Fixes: 5f0c2ee1fe8d ("bus: mhi: pci-generic: Fix hibernation")
Reported-by: Hemant Kumar <quic_hemantk@quicinc.com>
Suggested-by: Hemant Kumar <quic_hemantk@quicinc.com>
Link: https://lore.kernel.org/r/20220405125907.5644-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7acae6183cf37c48b8da48bbbdb78820fb3913f3 upstream.
The request will be inserted into the ci->i_unsafe_dirops before
assigning the req->r_session, so it's possible that we will hit
NULL pointer dereference bug here.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/55327
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Tested-by: Aaron Tomlin <atomlin@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1dc9f1a66e1718479e1c4f95514e1750602a3cb9 upstream.
When ACPI is not enabled, cpuid_topo->llc_id = cpu_topo->llc_id = -1, which
will set llc_sibling 0xff(...), this is misleading.
Don't set llc_sibling(default 0) if we don't know the cache topology.
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Wang Qing <wangqing@vivo.com>
Fixes: 37c3ec2d810f ("arm64: topology: divorce MC scheduling domain from core_siblings")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1649644580-54626-1-git-send-email-wangqing@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 637674fa40059cddcc3ad2212728965072f62ea3 upstream.
The EndRun PTP/1588 dual serial port device is based on the Oxford
Semiconductor OXPCIe952 UART device with the PCI vendor:device ID set
for EndRun Technologies and is therefore driven by a fixed 62.5MHz clock
input derived from the 100MHz PCI Express clock. The clock rate is
divided by the oversampling rate of 16 as it is supplied to the baud
rate generator, yielding the baud base of 3906250.
Replace the incorrect baud base of 4000000 with the right value of
3906250 then, complementing commit 6cbe45d8ac93 ("serial: 8250: Correct
the clock for OxSemi PCIe devices").
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable <stable@kernel.org>
Fixes: 1bc8cde46a159 ("8250_pci: Added driver for Endrun Technologies PTP PCIe card.")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181515270.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e6eebdf5e2455f089ccd000754a0deaeb79af82 upstream.
Sticky MCR bits are lost in console restoration if console suspending
has been disabled. This currently affects the AFE bit, which works in
combination with RTS which we set, so we want to make sure the UART
retains control of its FIFO where previously requested. Also specific
drivers may need other bits in the future.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 4516d50aabed ("serial: 8250: Use canary to restart console after suspend")
Cc: stable@vger.kernel.org # v4.0+
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181518490.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e4deb56b0c625efdb70c94f150429e2f2a16fa1 upstream.
The current timeout for draining the tx fifo in RS485 mode is calculated by
multiplying the time it takes to transmit one character (with the given
baud rate) with the maximal number of characters in the tx queue.
This timeout is too short for two reasons:
First when calculating the time to transmit one character integer division
is used which may round down the result in case of a remainder of the
division.
Fix this by rounding up the division result.
Second the hardware may need additional time (e.g for first putting the
characters from the fifo into the shift register) before the characters are
actually put onto the wire.
To be on the safe side double the current maximum number of iterations
that are used to wait for the queue draining.
Fixes: 8d479237727c ("serial: amba-pl011: add RS485 support")
Cc: stable@vger.kernel.org
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220408233503.7251-1-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
