IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
QCA6390 firmware uses HAL_RX_BUF_RBM_SW1_BM, not HAL_RX_BUF_RBM_SW3_BM. This is
needed to fix a case where an A-MSDU has an unexpected LLC/SNAP header in the
first subframe (CVE-2020-24588).
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914163726.38604-2-jouni@codeaurora.org
ath.git patches for v5.16. Major changes:
ath9k
* add option to reset the wifi chip via debugfs
* convert Device Tree bindings to the json-schema
* support Device Tree ieee80211-freq-limit property to limit channels
When powersaving (so either wifi powersaving or deep sleep, depending on
which state the firmware is in) is disabled, the way the firmware goes
into host sleep is different: Usually the firmware implicitely enters
host sleep on the next SLEEP event we get when we configured host sleep
via HSCFG before. When powersaving is disabled though, there are no
SLEEP events, the way we enter host sleep in that case is different: The
firmware will send us a HS_ACT_REQ event and after that we "manually"
make the firmware enter host sleep by sending it another HSCFG command
with the action HS_ACTIVATE.
Now waking up from host sleep appears to be different depending on
whether powersaving is enabled again: When powersaving is enabled, the
firmware implicitely leaves host sleep as soon as it wakes up and sends
us an AWAKE event. When powersaving is disabled though, it apparently
doesn't implicitely leave host sleep, but instead we need to send it a
HSCFG command with the HS_CONFIGURE action and the HS_CFG_CANCEL
condition. We didn't do that so far, which is why waking up from host
sleep was broken when powersaving is disabled.
So add some additional state to mwifiex_adapter where we keep track of
whether host sleep was activated manually via HS_ACTIVATE, and if that
was the case, deactivate it manually again via HS_CFG_CANCEL.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-6-verdre@v0yd.nl
While looking at on-air packets using Wireshark, I noticed we're never
setting the initiator bit when sending DELBA requests to the AP: While
we set the bit on our del_ba_param_set bitmask, we forget to actually
copy that bitmask over to the command struct, which means we never
actually set the initiator bit.
Fix that and copy the bitmask over to the host_cmd_ds_11n_delba command
struct.
Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Acked-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-5-verdre@v0yd.nl
Sometimes the KEY_MATERIAL command can fail with the 88W8897 firmware
(when this happens exactly seems pretty random). This appears to prevent
the access point from starting, so it seems like a good idea to log an
error in that case.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-3-verdre@v0yd.nl
It's not an error if someone chooses to put their computer to sleep, not
wanting it to wake up because the person next door has just discovered
what a magic packet is. So change the loglevel of this annoying message
from ERROR to INFO.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-2-verdre@v0yd.nl
Fix the return value check which testing the wrong variable
in rtw89_cam_send_sec_key_cmd().
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e3ec7017f6a2 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018033102.1813058-1-yangyingliang@huawei.com
When fail to init coex module, free 'common' and 'adapter' directly, but
common->tx_thread which will access 'common' and 'adapter' is running at
the same time. That will trigger the UAF bug.
==================================================================
BUG: KASAN: use-after-free in rsi_tx_scheduler_thread+0x50f/0x520 [rsi_91x]
Read of size 8 at addr ffff8880076dc000 by task Tx-Thread/124777
CPU: 0 PID: 124777 Comm: Tx-Thread Not tainted 5.15.0-rc5+ #19
Call Trace:
dump_stack_lvl+0xe2/0x152
print_address_description.constprop.0+0x21/0x140
? rsi_tx_scheduler_thread+0x50f/0x520
kasan_report.cold+0x7f/0x11b
? rsi_tx_scheduler_thread+0x50f/0x520
rsi_tx_scheduler_thread+0x50f/0x520
...
Freed by task 111873:
kasan_save_stack+0x1b/0x40
kasan_set_track+0x1c/0x30
kasan_set_free_info+0x20/0x30
__kasan_slab_free+0x109/0x140
kfree+0x117/0x4c0
rsi_91x_init+0x741/0x8a0 [rsi_91x]
rsi_probe+0x9f/0x1750 [rsi_usb]
Stop thread before free 'common' and 'adapter' to fix it.
Fixes: 2108df3c4b18 ("rsi: add coex support")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211015040335.1021546-1-william.xuanziyang@huawei.com
Add more MTK folks to actively maintain the wireless chipsets across
segments. The work is becoming increasingly complicated and various
and we can provides hardware related perspectives to offload
Felix's workload, especially for the 11ax and upcoming 11be devices
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/eb888ae0e43a980c2c1aaed372a9b5e8098ea4ef.1634107511.git.ryder.lee@mediatek.com
coccicheck complains about the use of snprintf() in sysfs show functions.
Fix the coccicheck warning:
WARNING: use scnprintf or sprintf.
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Signed-off-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634095651-4273-1-git-send-email-wangqing@vivo.com
The function rtw89_mac_enable_bb_rf is a void return type, so there is
no return error code to ret, so the following check for an error in ret
is redundant dead code and can be removed.
Addresses-Coverity: ("Logically dead code")
Fixes: e3ec7017f6a2 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211015152113.33179-1-colin.king@canonical.com
There are two spelling mistakes in rtw89_debug messages. Fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211015105004.11817-1-colin.king@canonical.com
It seems that the PCIe+USB firmware (latest version 15.68.19.p21) of the
88W8897 card sometimes ignores or misses when we try to wake it up by
writing to the firmware status register. This leads to the firmware
wakeup timeout expiring and the driver resetting the card because we
assume the firmware has hung up or crashed.
Turns out that the firmware actually didn't hang up, but simply "missed"
our wakeup request and didn't send us an interrupt with an AWAKE event.
Trying again to read the firmware status register after a short timeout
usually makes the firmware wake up as expected, so add a small retry
loop to mwifiex_pm_wakeup_card() that looks at the interrupt status to
check whether the card woke up.
The number of tries and timeout lengths for this were determined
experimentally: The firmware usually takes about 500 us to wake up
after we attempt to read the status register. In some cases where the
firmware is very busy (for example while doing a bluetooth scan) it
might even miss our requests for multiple milliseconds, which is why
after 15 tries the waiting time gets increased to 10 ms. The maximum
number of tries it took to wake the firmware when testing this was
around 20, so a maximum number of 50 tries should give us plenty of
safety margin.
Here's a reproducer for those firmware wakeup failures I've found:
1) Make sure wifi powersaving is enabled (iw dev wlp1s0 set power_save on)
2) Connect to any wifi network (makes firmware go into wifi powersaving
mode, not deep sleep)
3) Make sure bluetooth is turned off (to ensure the firmware actually
enters powersave mode and doesn't keep the radio active doing bluetooth
stuff)
4) To confirm that wifi powersaving is entered ping a device on the LAN,
pings should be a few ms higher than without powersaving
5) Run "while true; do iwconfig; sleep 0.0001; done", this wakes and
suspends the firmware extremely often
6) Wait until things explode, for me it consistently takes <5 minutes
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-3-verdre@v0yd.nl
On the 88W8897 PCIe+USB card the firmware randomly crashes after setting
the TX ring write pointer. The issue is present in the latest firmware
version 15.68.19.p21 of the PCIe+USB card.
Those firmware crashes can be worked around by reading any PCI register
of the card after setting that register, so read the PCI_VENDOR_ID
register here. The reason this works is probably because we keep the bus
from entering an ASPM state for a bit longer, because that's what causes
the cards firmware to crash.
This fixes a bug where during RX/TX traffic and with ASPM L1 substates
enabled (the specific substates where the issue happens appear to be
platform dependent), the firmware crashes and eventually a command
timeout appears in the logs.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-2-verdre@v0yd.nl
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/0855d51423578ad019c0264dad3fe47a2e8af9c7.1633849511.git.christophe.jaillet@wanadoo.fr
The variable ret is being initialized with a value that is never read,
it is assigned later on with a different value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211007234153.31222-1-colin.king@canonical.com
The variable version is being initialized with a value that is
never read, it is being updated afterwards in both branches of
an if statement. The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211007163722.20165-1-colin.king@canonical.com
This driver named rtw89, which is the next generation of rtw88, supports
Realtek 8852AE 802.11ax 2x2 chip whose new features are OFDMA, DBCC,
Spatial reuse, TWT and BSS coloring; now some of them aren't implemented
though.
The chip architecture is entirely different from the chips supported by
rtw88 like RTL8822CE 802.11ac chip. First of all, register address ranges
are totally redefined, so it's impossible to reuse register definition. To
communicate with firmware, new H2C/C2H format is proposed. In order to have
better utilization, TX DMA flow is changed to two stages DMA. To provide
rich RX status information, additional RX PPDU packets are added.
Since there are so many differences mentioned above, we decide to propose
a new driver. It has many authors, they are listed in alphabetic order:
Chin-Yen Lee <timlee@realtek.com>
Ping-Ke Shih <pkshih@realtek.com>
Po Hao Huang <phhuang@realtek.com>
Tzu-En Huang <tehuang@realtek.com>
Vincent Fann <vincent_fann@realtek.com>
Yan-Hsuan Chuang <tony0620emma@gmail.com>
Zong-Zhe Yang <kevin_yang@realtek.com>
Tested-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211008035627.19463-1-pkshih@realtek.com
Most of the txpower for the ath10k firmware is stored as twicepower (0.5 dB
steps). This isn't the case for max_antenna_gain - which is still expected
by the firmware as dB.
The firmware is converting it from dB to the internal (twicepower)
representation when it calculates the limits of a channel. This can be seen
in tpc_stats when configuring "12" as max_antenna_gain. Instead of the
expected 12 (6 dB), the tpc_stats shows 24 (12 dB).
Tested on QCA9888 and IPQ4019 with firmware 10.4-3.5.3-00057.
Fixes: 02256930d9b8 ("ath10k: use proper tx power unit")
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20190611172131.6064-1-sven@narfation.org
The devm_kmemdup() function doesn't return error pointers, it returns
NULL on error.
Fixes: eb3a97a69be8 ("ath9k: fetch calibration data via nvmem subsystem")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011123533.GA15188@kili
WMI_CHAN_INFO_DFS flag should be set when configuring a DFS channel
included in scan channel list. Without it, firmware will not send a
probe request frame which is needed in connection to an AP configured
with hidden SSID/network_id. So fix this to allow probe request frames
to be sent in cases where a beacon frame has been seen on the channel
first.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011054919.77071-1-bqiang@codeaurora.org
The common DT property can be used to limit the available channels
but ath9k has to manually call wiphy_read_of_freq_limits().
I would have put this into ath9k_of_init(). But it didn't work there.
The reason is that in ath9k_of_init() the channels and bands are not yet
registered in the wiphy struct. So there isn't any channel to flag as
disabled.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211009212847.1781986-1-chunkeey@gmail.com
Some targets, QCA6390 for example, use only one TCL ring, it is better to
initialize only one ring and leave others untouched for such targets.
This is a theoretical fix found during code review, no visible impact.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914163726.38604-1-jouni@codeaurora.org
When doing "rmmod ath11k_pci", ath11k performs global SOC reset
and MHI reset, where 0 address access is captured by IOMMU. See
log below:
...
[ 133.953860] ath11k_pci 0000:02:00.0: setting mhi state: DEINIT(1)
[ 133.959714] ath11k_pci 0000:02:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x000a address=0x0 flags=0x0020]
[ 133.973854] ath11k_pci 0000:02:00.0: MHISTATUS 0xff04
[ 133.974095] ath11k_pci 0000:02:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x000a address=0x0 flags=0x0020]
...
This issue is also observed in SSR process, cause a similar
sequence as above is performed.
Such an invalid access occurs because, during rmmod or SSR, MSI
address is cleared but HW MSI functionality not disabled, thus HW
target is able to raise an MSI transaction with 0 as MSI address.
So it can be fixed by simply disabling MSI before reset. For SSR,
since MSI functionality is still needed after target is brought
back, we need to reenable it.
Also change naming of some interfaces related.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913180246.193388-5-jouni@codeaurora.org
kzalloc() is used to allocate memory for cd->detectors, and if it fails,
channel_detector_exit() behind the label fail will be called:
channel_detector_exit(dpd, cd);
In channel_detector_exit(), cd->detectors is dereferenced through:
struct pri_detector *de = cd->detectors[i];
To fix this possible null-pointer dereference, check cd->detectors before
the for loop to dereference cd->detectors.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210805153854.154066-1-islituo@gmail.com
Variable fw_size is being assigned a value that is never read and
being re-assigned a new value in the next statement. The assignment
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Fixes: 336e7b53c82f ("ath11k: clean up BDF download functions")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211006105529.1011239-1-colin.king@canonical.com
The problem is that "channel" is an unsigned int, when it's less 5 the
value of "channel - 5" is not a negative number as one would expect but
is very high positive value instead.
This means that "start" becomes a very high positive value. The result
of that is that we never enter the "for (i = start; i <= end; i++) {"
loop. Instead of storing the result from b43legacy_radio_aci_detect()
it just uses zero.
Fixes: ef1a628d83fc ("b43: Implement dynamic PHY API")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211006073621.GE8404@kili
The problem is that "channel" is an unsigned int, when it's less 5 the
value of "channel - 5" is not a negative number as one would expect but
is very high positive value instead.
This means that "start" becomes a very high positive value. The result
of that is that we never enter the "for (i = start; i <= end; i++) {"
loop. Instead of storing the result from b43legacy_radio_aci_detect()
it just uses zero.
Fixes: 75388acd0cd8 ("[B43LEGACY]: add mac80211-based driver for legacy BCM43xx devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211006073542.GD8404@kili
This patch separates the logic of configuring hardware
maximum transmit frame size and receive frame size.
This simplifies the logic to calculate receive buffer
size and using cqe descriptor of different size.
Also additional size of skb_shared_info structure is
allocated for each receive buffer pointer given to
hardware which is not necessary. Hence change the
size calculation to remove the size of
skb_shared_info. Add a check for array out of
bounds while adding fragments to the network stack.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com> #mlx*
Signed-off-by: David S. Miller <davem@davemloft.net>
networking benchmark shows that __rcu_read_lock and
__rcu_read_unlock takes some cpu cycles, and we can avoid
calling them partially in virtio rx path by check xdp_enabled
of vi, and xdp is disabled most of time
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic commit making dev_get_port_parent_id slightly more readable.
There is no need to split the condition to return after calling
devlink_compat_switch_id_get and after that 'recurse' is always true.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Give a name to known debug regs from Documentation instead of using
unknown hex values.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
From original QCA source code the port was set to prefer master as port
type in 1000BASE-T mode. Apply the same settings also here.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
QCA8327 internal phy require DAC amplitude adjustement set to +6% with
100m speed. Also add additional define to report a change of the same
reg in QCA8337. (different scope it does set 1000m voltage)
Add link_change_notify function to set the proper amplitude adjustement
on PHY_RUNNING state and disable on any other state.
Fixes: b4df02b562f4 ("net: phy: at803x: add support for qca 8327 A variant internal phy")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From Documentation phy resume triggers phy reset and restart
auto-negotiation. Add a dedicated function to wait reset to finish as
it was notice a regression where port sometime are not reliable after a
suspend/resume session. The reset wait logic is copied from phy_poll_reset.
Add dedicated suspend function to use genphy_suspend only with QCA8337
phy and set only additional debug settings for QCA8327. With more test
it was reported that QCA8327 doesn't proprely support this mode and
using this cause the unreliability of the switch ports, especially the
malfunction of the port0.
Fixes: 15b9df4ece17 ("net: phy: at803x: add resume/suspend function to qca83xx phy")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Juhee Kang says:
====================
net-next: replace open code with helper functions
Currently, there are many helper functions on netdevice.h. However,
some code doesn't use the helper functions and remains open code.
So this patchset replaces open code with an appropriate helper function.
First patch modifies to use netif_is_rxfh_configured instead of
dev->priv_flags & IFF_RXFH_CONFIGURED.
Second patch replaces open code with netif_is_bond_master.
Last patch substitutes netif_is_macsec() for dev->priv_flags & IFF_MACSEC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Open code which is dev->priv_flags & IFF_MACSEC has already defined as
netif_is_macsec(). So use netif_is_macsec() instead of open code.
This patch doesn't change logic.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netif_is_bond_master() function instead of open code, which is
((event_dev->priv_flags & IFF_BONDING) && (event_dev->flags & IFF_MASTER)).
This patch doesn't change logic.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The open code which is dev->priv_flags & IFF_RXFH_CONFIGURED is defined as
a helper function on netdevice.h. So use netif_is_rxfh_configured()
function instead of open code. This patch doesn't change logic.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson says:
====================
ionic: add vlanid overflow management
Add vlans to the existing rx_filter_sync mechanics currently
used for managing mac filters.
Older versions of our firmware had no enforced limits on the
number of vlans that the driver could request, but requesting
large numbers of vlans caused issues in FW memory management,
so an arbitrary limit was added in the FW. The FW now
returns -ENOSPC when it hits that limit, which the driver
needs to handle.
Unfortunately, the FW doesn't advertise the vlan id limit,
as it does with mac filters, so the driver won't know the
limit until it bumps into it. We'll grab the current vlan id
count and use that as the limit from there on and thus prevent
getting any more -ENOSPC errors.
Just as is done for the mac filters, the device puts the device
into promiscuous mode when -ENOSPC is seen for vlan ids, and
the driver will track the vlans that aren't synced to the FW.
When vlans are removed, the driver will retry the un-synced
vlans. If all outstanding vlans are synced, the promiscuous
mode will be disabled.
The first 6 patches rework the existing filter management to
make it flexible enough for additional filter types. Next
we add the vlan ids into the management. The last 2 patches
allow us to catch the max vlan -ENOSPC error without adding
an unnecessary error message to the kernel log.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Override the automatic AdminQ error message in order to
capture the potential No Space message when we hit the
max vlan limit, and add additional messaging to detail
what filter failed.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AdminQ handler has an error handler that automatically prints
an error message when the request has failed. However, there are
situations where the caller can expect that it might fail and has
an alternative strategy, thus may not want the error message sent
to the log, such as hitting -ENOSPC when adding a new vlan id.
We add a new interface to the AdminQ API to allow for override of
the default behavior, and an interface to the use standard error
message formatting.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add vlans to the existing rx_filter_sync mechanics currently
used for managing mac filters.
Older versions of our firmware had no enforced limits on the
number of vlans that the LIF could request, but requesting large
numbers of vlans caused issues in FW memory management, so an
arbitrary limit was added in the FW. The FW now returns -ENOSPC
when it hits that limit, which the driver needs to handle.
Unfortunately, the FW doesn't advertise the vlan id limit,
as it does with mac filters, so the driver won't know the
limit until it bumps into it. We'll grab the current vlan id
count and use that as the limit from there on and thus prevent
getting any more -ENOSPC errors.
Just as is done for the mac filters, the device puts the device
into promiscuous mode when -ENOSPC is seen for vlan ids, and
the driver will track the vlans that aren't synced to the FW.
When vlans are removed, the driver will retry the un-synced
vlans. If all outstanding vlans are synced, the promiscuous
mode will be disabled.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the filter add, make a generic filter delete.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
