IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Zinitix BT532 is another touch controller that seem to implement the
same interface as an already supported BT541. Add it to the driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-5-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The supply names of the Zinitix touchscreen were a bit confused, the new
bindings rectifies this.
To deal with old and new devicetrees, first check if we have "vddo" and in
case that exists assume the old supply names. Else go and look for the new
ones.
We cannot just get the regulators since we would get an OK and a dummy
regulator: we need to check explicitly for the old supply name.
Use struct device *dev as a local variable instead of the I2C client since
the device is what we are actually obtaining the resources from.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[Slightly changed the legacy regulator detection]
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-4-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This converts the Zinitix BT4xx and BT5xx touchscreen bindings to YAML,
fix them up a bit and extends them.
We list all the existing BT4xx and BT5xx components with compatible
strings. These are all similar, use the same bindings and work in
similar ways.
We rename the supplies from the erroneous vdd/vddo to the actual supply
names vcca/vdd as specified on the actual component. It is long
established that supplies shall be named after the supply pin names of a
component. The confusion probably stems from that in a certain product
the rails to the component were named vdd/vddo. Drop some notes on how OS
implementations should avoid confusion by first looking for vddo, and if
that exists assume the legacy binding pair and otherwise use vcca/vdd.
Add reset-gpios as sometimes manufacturers pulls a GPIO line to the reset
line on the chip.
Add optional touchscreen-fuzz-x and touchscreen-fuzz-y properties.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[Fixed dt_schema_check]
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-3-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since irq request is the last thing in the driver probe, it happens
later than the input device registration. This means that there is a
small time window where if the open method is called the driver will
attempt to enable not yet available irq.
Fix that by moving the irq request before the input device registration.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 26822652c85e ("Input: add zinitix touchscreen driver")
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-2-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The power button on Cherry Trail systems with an AXP288 PMIC is connected
to both the power button pin of the PMIC as well as to a power button GPIO
on the Cherry Trail SoC itself. This leads to double power button event
reporting which is a problem.
Since reporting power button presses through the PMIC is not supported on
all PMICs used on Cherry Trail systems, we want to keep the GPIO
power button events, so the axp20x-pek code checks for the presence of
a GPIO power button and in that case does not register its input-device.
On most systems the GPIO power button also can wake-up the system from
suspend, so the axp20x-pek driver would also not register its interrupt
handler. But on some systems there was a bug causing wakeup by the GPIO
power button handler to not work.
Commit 9747070c11d6 ("Input: axp20x-pek - always register interrupt
handlers") was added as a work around for this registering the axp20x-pek
interrupts, but not the input-device on Cherry Trail systems.
In the mean time the root-cause of the GPIO power button wakeup events
not working has been found and fixed by the "pinctrl: cherryview: Do not
allow the same interrupt line to be used by 2 pins" patch,
so this is no longer necessary.
This reverts the workaround going back to only registering the
interrupt handlers on systems where we also register the input-device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20220106111647.66520-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The spaceball.c module was not properly parsing the movement reports
coming from the device. The code read axis data as signed 16-bit
little-endian values starting at offset 2.
In fact, axis data in Spaceball movement reports are signed 16-bit
big-endian values starting at offset 3. This was determined first by
visually inspecting the data packets, and later verified by consulting:
http://spacemice.org/pdf/SpaceBall_2003-3003_Protocol.pdf
If this ever worked properly, it was in the time before Git...
Signed-off-by: Leo L. Schwab <ewhac@ewhac.org>
Link: https://lore.kernel.org/r/20211221101630.1146385-1-ewhac@ewhac.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Syzbot has reported warning in __flush_work(). This warning is caused by
work->func == NULL, which means missing work initialization.
This may happen, since input_dev->close() calls
cancel_work_sync(&dev->work), but dev->work initalization happens _after_
input_register_device() call.
So this patch moves dev->work initialization before registering input
device
Fixes: 5a6eb676d3bc ("Input: appletouch - improve powersaving for Geyser3 devices")
Reported-and-tested-by: syzbot+b88c5eae27386b252bbd@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20211230141151.17300-1-paskripkin@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The eKTH3900/eKTH5312 series do not support the firmware update rules of
Remark ID. Exclude these two series from checking it when updating the
firmware in touch controllers.
Signed-off-by: Johnny Chuang <johnny.chuang.emc@gmail.com>
Link: https://lore.kernel.org/r/1639619603-20616-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Variable penup is assigned a value but penup is never read later, it
is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20211205000525.153999-1-colin.i.king@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The open delay time has to be applied only on the first sample of the
X/Y coordinates because on the following samples the ADC channel is not
changed. Removing this time from the samples after the first one,
"ti,coordinate-readouts" greater than 1, decreases the total acquisition
time, allowing to increase the number of acquired coordinates in the time
unit.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-4-dariobin@libero.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Z2 step configuration doesn't erase the SEL_INP_SWC_3_0 bit-field
before setting the ADC channel. This way its value could be corrupted by
the ADC channel selected for the Z1 coordinate.
Fixes: 8c896308feae ("input: ti_am335x_adc: use only FIFO0 and clean up a little")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-3-dariobin@libero.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As reported by the STEPCONFIG[1-16] registered field descriptions of the
TI reference manual, for the ADC "in single ended, SEL_INM_SWC_3_0 must
be 1xxx".
Unlike the Y and Z coordinates, this bit has not been set for the step
configuration registers used to sample the X coordinate.
Fixes: 1b8be32e6914 ("Input: add support for TI Touchscreen controller")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-2-dariobin@libero.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some Silead touchscreens have support for an active (battery powered)
pen, add support for this.
So far pen-support has only been seen on X86/ACPI (non devicetree) devs,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new properties are deliberately not added
to the existing silead devicetree-bindings documentation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211122220637.11386-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unfortunately, at the time of writing this commit message, we have been
unable to get permission from Silead, or from device OEMs, to distribute
the necessary Silead firmware files in linux-firmware.
On a whole bunch of devices the UEFI BIOS code contains a touchscreen
driver, which contains an embedded copy of the firmware. The fw-loader
code has a "platform" fallback mechanism, which together with info on the
firmware from drivers/platform/x86/touchscreen_dmi.c will use the firmware
from the UEFI driver when the firmware is missing from /lib/firmware. This
makes the touchscreen work OOTB without users needing to manually download
the firmware.
The firmware bundled with the original Windows/Android is usually newer
then the firmware in the UEFI driver and it is better calibrated. This
better calibration can lead to significant differences in the reported
min/max coordinates.
Add support for a new (optional) "silead,efi-fw-min-max" property which
provides a set of alternative min/max values to use for the x/y axis when
the EFI embedded firmware is used.
The new property is only used on (x86) devices which do not use devicetree,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new property is deliberately not added to the
existing silead devicetree-bindings documentation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211122220637.11386-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2 small fixes for pen support
1. Set the id.vendor field for the pen input_dev
2. Fix a typo in a comment
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211212124242.81019-5-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
goodix_get_gpio_config() errors are fatal (abort probe()) so log them
at KERN_ERR level rather then as debug messages.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211212124242.81019-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The "id_buf" buffer is stored in "data->raw_info_block" and freed by
"mxt_free_object_table" in case of error.
Return instead of jumping to avoid a double free.
Addresses-Coverity-ID: 1474582 ("Double free")
Fixes: 068bdb67ef74 ("Input: atmel_mxt_ts - fix the firmware update")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20211212194257.68879-1-jose.exposito89@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmF/AjYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1hkIAJ6sFDbvb4M4LMwf
Slh2NVL9o5sLMBDzVwnVlyMSKDbMn1WBKreGssaLgZjGDc74lxsdSmw5l9MZm0JN
xlq95Q6XFiuu+0qDHPWwfDz3JFO4TqW2ZLLPWk9NnkNbRXqccSrlVRi1RpgE1t3/
NUtS8CQLu6A2BYMc6mkk3aV6IwSNKOkWbM5eBHSvU4j8B6lLbNQop0AfO/wyY1xB
U6LiVE1RpN/b7Yv+75ITtNzuHzVIBx6305FvSnOlKbMKKvIClt96Vd2OeuoEkK+6
wGU8JraB1+fc0GckAhynNrjWQWdvi0MAhFWWEJxjS20OGcV1rXDduNfkVNauO1Zn
+dNyJ3s=
=g9fz
-----END PGP SIGNATURE-----
Merge tag 'v5.15' into next
Sync up with the mainline to get the latest APIs and DT bindings.
Add d->model mapping for the "9111" model, this fixes uses using
a wrong config_len of 240 bytes while the "9111" model uses
only 186 bytes of config.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206164747.197309-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When converting a rumble into a periodic effect, for compatibility,
the magnitude is effectively calculated using:
magnitude = max(strong_rubble / 3 + weak_rubble / 6, 0x7fff);
The rumble magnitudes are both u16 and the resulting magnitude is
s16. The max is presumably an attempt to limit the result of the
calculation to the maximum possible magnitude for the s16 result,
and thus should be a min.
However in the case of strong = weak = 0xffff, the result of the first
part of the calculation is 0x7fff, meaning that the min would be
redundant anyway, so simply remove the current max.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211130135039.13726-1-ckeepax@opensource.cirrus.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Don't populate a couple of arrays on the stack but instead make them
static const. Also makes the object code smaller by a few hundred
bytes.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20211129231749.619469-1-colin.i.king@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unless the controller is not responding at boot or after suspend/resume,
the driver never resets the controller on x86/ACPI platforms. The driver
still requesting the reset pin at probe() though in case it needs it.
Until now the driver has always requested the reset pin with GPIOD_IN
as type. The idea being to put the pin in high-impedance mode to save
power until the driver actually wants to issue a reset.
But this means that just requesting the pin can cause issues, since
requesting it in another mode then GPIOD_ASIS may cause the pinctrl
driver to touch the pin settings. We have already had issues before
due to a bug in the pinctrl-cherryview.c driver which has been fixed in
commit 921daeeca91b ("pinctrl: cherryview: Preserve
CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs").
And now it turns out that requesting the reset-pin as GPIOD_IN also stops
the touchscreen from working on the GPD P2 max mini-laptop. The behavior
of putting the pin in high-impedance mode relies on there being some
external pull-up to keep it high and there seems to be no pull-up on the
GPD P2 max, causing things to break.
This commit fixes this by requesting the reset pin as is when using
the x86/ACPI code paths to lookup the GPIOs; and by not dropping it
back into input-mode in case the driver does end up issuing a reset
for error-recovery.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209061
Fixes: a7d4b171660c ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206091116.44466-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ASUS UM325UA suffers from the same issue as the ASUS UX425UA, which
is a very similar laptop. The i8042 device is not usable immediately
after boot and fails to initialize, requiring a deferred retry.
Enable the deferred probe quirk for the UM325UA.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190256
Signed-off-by: Samuel Čavoj <samuel@cavoj.net>
Link: https://lore.kernel.org/r/20211204015615.232948-1-samuel@cavoj.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some automated builds report a stack frame size in excess of 2 kB for
iqs626_probe(); the culprit appears to be the call to iqs626_parse_prop().
To solve this problem, specify noinline_for_stack for all of the
iqs626_parse_*() helper functions which are called inside a for loop
within iqs626_parse_prop().
As a result, a build with '-Wframe-larger-than' as low as 512 is free of
any such warnings.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20211129004104.453930-1-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We've got a bug report about the non-working keyboard on ASUS ZenBook
UX425UA. It seems that the PS/2 device isn't ready immediately at
boot but takes some seconds to get ready. Until now, the only
workaround is to defer the probe, but it's available only when the
driver is a module. However, many distros, including openSUSE as in
the original report, build the PS/2 input drivers into kernel, hence
it won't work easily.
This patch adds the support for the deferred probe for i8042 stuff as
a workaround of the problem above. When the deferred probe mode is
enabled and the device couldn't be probed, it'll be repeated with the
standard deferred probe mechanism.
The deferred probe mode is enabled either via the new option
i8042.probe_defer or via the quirk table entry. As of this patch, the
quirk table contains only ASUS ZenBook UX425UA.
The deferred probe part is based on Fabio's initial work.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190256
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Samuel Čavoj <samuel@cavoj.net>
Link: https://lore.kernel.org/r/20211117063757.11380-1-tiwai@suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes: 487358627825 ("Input: iforce - use DMA-safe buffer when getting IDs from USB")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 5.3
Link: https://lore.kernel.org/r/20211025115501.5190-1-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Modern devices may redraw display at 60 Hz, make sure we have one input
sample per one frame. Reduce sample period to 15ms, so we would get up
to 66.6 samples per second, although realistically with all the jitter
and extra scheduling wiggle room, we would end up just above 60 samples
per second. This should be a good compromise between sampling too often
and sampling too seldom.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108114145.84118-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently the ili210x driver implements a threaded interrupt handler which
starts upon edge on the interrupt line, and then polls the touch controller
for samples. Every time a sample is obtained from the controller, the thread
function checks whether further polling is required, and if so, waits fixed
amount of time before polling for next sample.
The delay between consecutive samples can thus vary greatly, because the
I2C transfer required to retrieve the sample from the controller takes
different amount of time on different platforms. Furthermore, different
models of the touch controllers supported by this driver require different
delays during retrieval of samples too.
Instead of waiting fixed amount of time before polling for next sample,
determine how much time passed since the beginning of sampling cycle and
then wait only the remaining amount of time within the sampling cycle.
This makes the driver deliver samples with equal spacing between them.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005216.480525-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ili251x touch controller needs 5ms delay between sending I2C device
address and register address, and, writing or reading register data.
According to downstream ili251x example code, this 5ms delay is not
required when reading touch samples out of the controller. Implement
such a special case.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005259.480545-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some firmwares occasionally report bogus data from trackpoint, with X or Y
displacement being too large (outside of [-127, 127] range). Let's drop such
packets so that we do not generate jumps.
Signed-off-by: Phoenix Huang <phoenix@emc.com.tw>
Tested-by: Yufei Du <yufeidu@cs.unc.edu>
Link: https://lore.kernel.org/r/20210729010940.5752-1-phoenix@emc.com.tw
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The created rmi device is orphan, which breaks the real device
hierarchy, and can cause some trouble, especially during suspend
and resume sequences. E.g. in case of I2C, rmi dev should be child
of the I2C client device.
Fix this, assigning the transport device as parent of the rmi device.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1635514971-18415-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fujitsu Lifebook T725 laptop requires, like a few other similar
models, the nomux and notimeout options to probe the touchpad
properly. This patch adds the corresponding quirk entries.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1191980
Tested-by: Neal Gompa <ngompa13@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20211103070019.13374-1-tiwai@suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to the datasheet "The CAP1206 is pin- and register-compatible
with the CAP1106, with the exception of the GAIN[1:0] bits and ALT_POL
bit"(57). So, this patch aims to disable them as they are no longer
used.
Signed-off-by: Jesse Taube <mr.bossman075@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 83b41248ed04 ("Input: cy8ctmg110_ts - switch to using gpiod API")
remove the last use of <linux/input/cy8ctmg110_pdata.h> but left the header
file behind. Nothing uses it now, delete it.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20211102220203.940290-6-corbet@lwn.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- Fix compilation of callchain related code on powerpc with gcc11+.
- Fix PERF_SAMPLE_WEIGHT_STRUCT support in 'perf script'
- Check session->header.env.arch before using it, fixing a segmentation fault.
- Suppress 'rm dlfilter' build messages.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCYX7NvgAKCRCyPKLppCJ+
J0kmAQCAuh2Pt2eL+KUat/RgHXG+on5EkFfqlHVzebjmTv3/nwD/eyKF5AcgvTfb
DGIntW5QskCeAal05g9Po1+xPdU2aQU=
=3oio
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-fixes-for-v5.15-2021-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Fix compilation of callchain related code on powerpc with gcc11+
- Fix PERF_SAMPLE_WEIGHT_STRUCT support in 'perf script'
- Check session->header.env.arch before using it, fixing a segmentation
fault
- Suppress 'rm dlfilter' build messages
* tag 'perf-tools-fixes-for-v5.15-2021-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf script: Fix PERF_SAMPLE_WEIGHT_STRUCT support
perf callchain: Fix compilation on powerpc with gcc11+
perf script: Check session->header.env.arch before using it
perf build: Suppress 'rm dlfilter' build message
* Fixes for Xen emulator bugs showing up as debug kernel WARNs
* Fix another issue with SEV/ES string I/O VMGEXITs
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmF6uGIUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNRagf/Srvk9lNcRh4cEzsczErKMyr3xOqA
jgsTSqgl1ExJI9sBLMpVYBOFGILMaMSrhLPIltKPy0Bj/E+hw8WOQwPa44QjWlSD
MAUxO1Nryt9Luc2L8uSd1c//g4fr4V1BhOaumk1lM14Q8EDfQBcDIMI2ZKueMU1+
2Q+n8/AsG63jQIINwKNidof0dzRtbfcE30Wq/8QHttIPo5wt6l0YClOlOikqNY8N
5+WSQFmuutHIXftq5Jb/Ldn/+HVukWZyZOEVwLnBpM9uBvIubNgcEakqvxsaVtAn
FHdvnA+Bk99/Xuhl+wRLQo8ofzQIQ13RQv3HPArJAJv34oAJZx2rNObVlA==
=6ofB
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
- Fixes for s390 interrupt delivery
- Fixes for Xen emulator bugs showing up as debug kernel WARNs
- Fix another issue with SEV/ES string I/O VMGEXITs
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Take srcu lock in post_kvm_run_save()
KVM: SEV-ES: fix another issue with string I/O VMGEXITs
KVM: x86/xen: Fix kvm_xen_has_interrupt() sleeping in kvm_vcpu_block()
KVM: x86: switch pvclock_gtod_sync_lock to a raw spinlock
KVM: s390: preserve deliverable_mask in __airqs_kick_single_vcpu
KVM: s390: clear kicked_mask before sleeping again
-F weight in perf script is broken.
# ./perf mem record
# ./perf script -F weight
Samples for 'dummy:HG' event do not have WEIGHT attribute set. Cannot
print 'weight' field.
The sample type, PERF_SAMPLE_WEIGHT_STRUCT, is an alternative of the
PERF_SAMPLE_WEIGHT sample type. They share the same space, weight. The
lower 32 bits are exactly the same for both sample type. The higher 32
bits may be different for different architecture. For a new kernel on
x86, the PERF_SAMPLE_WEIGHT_STRUCT is used. For an old kernel or other
ARCHs, the PERF_SAMPLE_WEIGHT is used.
With -F weight, current perf script will only check the input string
"weight" with the PERF_SAMPLE_WEIGHT sample type. Because the commit
ea8d0ed6eae3 ("perf tools: Support PERF_SAMPLE_WEIGHT_STRUCT") didn't
update the PERF_SAMPLE_WEIGHT_STRUCT sample type for perf script. For a
new kernel on x86, the check fails.
Use PERF_SAMPLE_WEIGHT_TYPE, which supports both sample types, to
replace PERF_SAMPLE_WEIGHT
Fixes: ea8d0ed6eae37b01 ("perf tools: Support PERF_SAMPLE_WEIGHT_STRUCT")
Reported-by: Joe Mario <jmario@redhat.com>
Reviewed-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Tested-by: Joe Mario <jmario@redhat.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Joe Mario <jmario@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Link: https://lore.kernel.org/r/1632929894-102778-1-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Got following build fail on powerpc:
CC arch/powerpc/util/skip-callchain-idx.o
In function ‘check_return_reg’,
inlined from ‘check_return_addr’ at arch/powerpc/util/skip-callchain-idx.c:213:7,
inlined from ‘arch_skip_callchain_idx’ at arch/powerpc/util/skip-callchain-idx.c:265:7:
arch/powerpc/util/skip-callchain-idx.c:54:18: error: ‘dwarf_frame_register’ accessing 96 bytes \
in a region of size 64 [-Werror=stringop-overflow=]
54 | result = dwarf_frame_register(frame, ra_regno, ops_mem, &ops, &nops);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/powerpc/util/skip-callchain-idx.c: In function ‘arch_skip_callchain_idx’:
arch/powerpc/util/skip-callchain-idx.c:54:18: note: referencing argument 3 of type ‘Dwarf_Op *’
In file included from /usr/include/elfutils/libdwfl.h:32,
from arch/powerpc/util/skip-callchain-idx.c:10:
/usr/include/elfutils/libdw.h:1069:12: note: in a call to function ‘dwarf_frame_register’
1069 | extern int dwarf_frame_register (Dwarf_Frame *frame, int regno,
| ^~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
The dwarf_frame_register args changed with [1],
Updating ops_mem accordingly.
[1] https://sourceware.org/git/?p=elfutils.git;a=commit;h=5621fe5443da23112170235dd5cac161e5c75e65
Reviewed-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Mark Wieelard <mjw@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20210928195253.1267023-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
