IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Wangxun NICs support the connection with SFP to RJ45 module. In this case,
PCS need to be configured in SGMII mode.
According to chapter 6.11.1 "SGMII Auto-Negitiation" of DesignWare Cores
Ethernet PCS (version 3.20a) and custom design manual, do the following
configuration when the interface mode is SGMII.
1. program VR_MII_AN_CTRL bit(3) [TX_CONFIG] = 1b (PHY side SGMII)
2. program VR_MII_AN_CTRL bit(8) [MII_CTRL] = 1b (8-bit MII)
3. program VR_MII_DIG_CTRL1 bit(0) [PHY_MODE_CTRL] = 1b
Also CL37 AN in backplane configurations need to be enabled because of the
special hardware design. Another thing to note is that PMA needs to be
reconfigured before each CL37 AN configuration for SGMII, otherwise AN will
fail, although we don't know why.
On this device, CL37_ANSGM_STS (bit[4:1] of VR_MII_AN_INTR_STS) indicates
the status received from remote link during the auto-negotiation, and
self-clear after the auto-negotiation is complete.
Meanwhile, CL37_ANCMPLT_INTR will be set to 1, to indicate CL37 AN is
complete. So add another way to get the state for CL37 SGMII.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable CL37 AN complete interrupt for DW XPCS. It requires to clear the
bit(0) [CL37_ANCMPLT_INTR] of VR_MII_AN_INTR_STS after AN completed.
And there is a quirk for Wangxun devices to enable CL37 AN in backplane
configurations because of the special hardware design.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to chapter 6 of DesignWare Cores Ethernet PCS (version 3.20a)
and custom design manual, add a configuration flow for switching interface
mode.
If the interface changes, the following setting is required:
1. wait VR_XS_PCS_DIG_STS bit(4, 2) [PSEQ_STATE] = 100b (Power-Good)
2. write SR_XS_PCS_CTRL2 to select various PCS type
3. write SR_PMA_CTRL1 and/or SR_XS_PCS_CTRL1 for link speed
4. program PMA registers
5. write VR_XS_PCS_DIG_CTRL1 bit(15) [VR_RST] = 1b (Vendor-Specific
Soft Reset)
6. wait for VR_XS_PCS_DIG_CTRL1 bit(15) [VR_RST] to get cleared
Only 10GBASE-R/SGMII/1000BASE-X modes are planned for the current Wangxun
devices. And there is a quirk for Wangxun devices to switch mode although
the interface in phylink state has not changed, since PCS will change to
default 10GBASE-R when the ethernet driver(txgbe) do LAN reset.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Wangxun 10Gb NICs require some special configuration on the IP of
Synopsys Designware XPCS, introduce dev_flag for different vendors. Read
OUI from device identifier registers, to detect Wangxun devices.
And xpcs_soft_reset() is skipped to avoid the reset of device identifier
registers.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When switching from 10GBase-R/5GBase-R/USXGMII to one of the interface
modes provided by mtk-pcs-lynxi we need to make sure to always perform
a full configuration of the PHYA.
Implement pcs_disable op which resets the stored interface mode to
PHY_INTERFACE_MODE_NA to trigger a full reconfiguration once the LynxI
PCS driver had previously been deselected in favor of another PCS
driver such as the to-be-added driver for the USXGMII PCS found in
MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/f23d1a60d2c9d2fb72e32dcb0eaa5f7e867a3d68.1692327891.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/sfc/tc.c
fa165e1949 ("sfc: don't unregister flow_indr if it was never registered")
3bf969e88a ("sfc: add MAE table machinery for conntrack table")
https://lore.kernel.org/all/20230818112159.7430e9b4@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
lynx_pcs_link_up_sgmii() is supposed to update the PCS speed and duplex
for the non-inband operating modes, and prior to the blamed commit, it
did just that, but a mistake sneaked into the conversion and reversed
the condition.
It is easy for this to go undetected on platforms that also initialize
the PCS in the bootloader, because Linux doesn't reset it (although
maybe it should). The nature of the bug is that phylink will not touch
the IF_MODE_HALF_DUPLEX | IF_MODE_SPEED_MSK fields when it should, and
it will apparently keep working if the previous values set by the
bootloader were correct.
Fixes: c689a6528c ("net: pcs: lynx: update PCS driver to use neg_mode")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reference of pdev->dev is taken by of_find_device_by_node, so
it should be released when not need anymore.
Fixes: 7dc54d3b8d ("net: pcs: add Renesas MII converter driver")
Signed-off-by: Xiang Yang <xiangyang3@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230724211905.805665-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the Lynx PCS driver to use neg_mode rather than the mode
argument. This ensures that the link_up() method will always program
the speed and duplex when negotiation is disabled.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8E4-00EaFf-Bf@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the Lynxi PCS driver to use neg_mode rather than the mode
argument. This ensures that the link_up() method will always program
the speed and duplex when negotiation is disabled.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Dz-00EaFY-5A@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update xpcs to use neg_mode to configure whether inband negotiation
should be used. We need to update sja1105 as well as that directly
calls into the XPCS driver's config function.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Dt-00EaFS-W9@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert fman_dtsec, xilinx_axienet and pcs-lynx to pass the neg_mode
into phylink_mii_c22_pcs_config(). Where appropriate, drivers are
updated to have neg_mode passed into their pcs_config() and
pcs_link_up() functions. For other drivers, we just hoist the call
to phylink_pcs_neg_mode() to their pcs_config() method out of
phylink_mii_c22_pcs_config().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Do-00EaFM-Ra@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Check that the fwnode is marked as available prior to trying to lookup
the PCS device, and return -ENODEV if unavailable. Document the return
codes from lynx_pcs_create_fwnode().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change lynx_pcs_create() to return an error-pointer on failure to
allocate memory, rather than returning NULL. This allows the removal
of the conversion in lynx_pcs_create_fwnode() and
lynx_pcs_create_mdiodev().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We no longer need to export lynx_pcs_create() for drivers to use as we
now have all the functionality we need in the two new creation helpers.
Remove the export and prototype, and make it static.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a helper to create a lynx PCS from a fwnode handle.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
lynx_get_mdio_device() is no longer necessary, let's remove it so the
lynx PCS code is always managing the lifetime of the mdiodev.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add basic support for XPCS using 10GBASE-R interface. This mode will
be extended to use interrupt, so set pcs.poll false. And avoid soft
reset so that the device using this mode is in the default configuration.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are now no callers of xpcs_create(), so let's remove it from
public view to discourage future direct usage.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we can easily create a mdio-device that represents a
memory-mapped device that exposes an MDIO-like register layout, we don't
need the Altera TSE PCS anymore, since we can use the Lynx PCS instead.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add lynx_pcs_create_mdiodev() to simplify the creation of the mdio
device associated with lynx PCS. In order to allow lynx_pcs_destroy()
to clean this up, we need to arrange for lynx_pcs_create() to take a
refcount on the mdiodev, and lynx_pcs_destroy() to put it.
Adding the refcounting to lynx_pcs_create()..lynx_pcs_destroy() will
be transparent to existing users of these interfaces.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add xpcs_create_mdiodev() to simplify the creation of the mdio device
associated with the XPCS. In order to allow xpcs_destroy() to clean
this up, we need to arrange for xpcs_create() to take a refcount on
the mdiodev, and xpcs_destroy() to put it.
Adding the refcounting to xpcs_create()..xpcs_destroy() will be
transparent to existing users of these interfaces.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Avoid reading the STAT1 registers more than once while getting the PCS
state, as this register contains latching-low bits that are lost after
the first read.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use phylink_resolve_c73() to resolve the clause 73 autonegotiation
result.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xpcs was indicating symmetric pause should be enabled regardless of
the advertisements by either party. Fix this to use
linkmode_resolve_pause() now that we're no longer obliterating the
link partner's advertisement by logically anding it with our own.
This is transitional, the function will be entirely replaced with
phylink_resolve_c73() in the following patch.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
lp_advertising is supposed to reflect the link partner's advertisement
unmodified by the local advertisement, but xpcs bitwise ands it with
the local advertisement prior to calculating the resolution of the
negotiation.
Fix this by moving the bitwise and to xpcs_resolve_lpa_c73() so it can
place the results in a temporary bitmap before passing that to
ixpcs_get_max_usxgmii_speed().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert xpcs clause 73 reading to use the newly introduced
mii_c73_to_linkmode() helper to translate the link partner
advertisement to an ethtool bitmap.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Read the clause 73 link partner advertisement in a loop and then
translate to the ethtool modes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The XPCS expects clause 73 (copper backplane) autoneg to follow the
ethtool autoneg bit. It actually did that until the blamed
commit inaptly replaced state->an_enabled (coming from ethtool) with
phylink_autoneg_inband() (coming from the device tree or struct
phylink_config), as part of an unrelated phylink_pcs API conversion.
Russell King suggests that state->an_enabled from the original code was
just a proxy for the ethtool Autoneg bit, and that the correct way of
restoring the functionality is to check for this bit in the advertising
mask.
Fixes: 11059740e6 ("net: pcs: xpcs: convert to phylink_pcs_ops")
Link: https://lore.kernel.org/netdev/ZGNt2MFeRolKGFck@shell.armlinux.org.uk/
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In synopsys_xpcs_compat[], the DW_XPCS_2500BASEX entry was setting
the number of interfaces using the xpcs_2500basex_features array
rather than xpcs_2500basex_interfaces. This causes us to overflow
the array of interfaces. Fix this.
Fixes: f27abde304 ("net: pcs: add 2500BASEX support for Intel mGbE controller")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Autoneg bit in the advertising bitmap and state->an_enabled are
always identical. Thus, we will be removing state->an_enabled.
Use the Autoneg bit in the advertising bitmap to indicate whether
autonegotiation should be used, rather than using the an_enabled
member which will be going away.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SGMII core found in several MediaTek SoCs is identical to what can
also be found in MediaTek's MT7531 Ethernet switch IC.
As this has not always been clear, both drivers developed different
implementations to deal with the PCS.
Recently Alexander Couzens pointed out this fact which lead to the
development of this shared driver.
Add a dedicated driver, mostly by copying the code now found in the
Ethernet driver. The now redundant code will be removed by a follow-up
commit.
Suggested-by: Alexander Couzens <lynxis@fe80.eu>
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
an_enabled will be going away, and in any case, pcs_get_state() should
not be updating this member. Remove the print.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phylink does not want the current state of the link when reading the
PCS link state - it wants the latched state. Don't double-read the
MII status register. Phylink will re-read as necessary to capture
transient link-down events as of dbae3388ea ("net: phylink: Force
retrigger in case of latched link-fail indicator").
The above referenced commit is a dependency for this change, and thus
this change should not be backported to any kernel that does not
contain the above referenced commit.
Fixes: fcb26bd2b6 ("net: phy: Add Synopsys DesignWare XPCS MDIO module")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the phylink_get_link_timer_ns() helper to get the period for the
link timer.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1pFyhW-0067jq-Fh@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert the PCS-XPCS driver to make use of the C45 MDIO bus API for
modify_change().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
remove unused register definitions, left from the split with the
altera-tse mac driver.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When disabling the SGMII mode bit, the PCS defaults to 1000BaseX mode.
In that mode, we don't need to set the speed since it's always 1000Mbps.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Software resets on the TSE PCS don't clear registers, but rather reset
all internal state machines regarding AN, comma detection and
encoding/decoding. Use read_poll_timeout to wait for the reset to clear
instead of manually polling the register.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use mdiodev accessors rather than accessing the bus and address in
the mdio_device structure and using the mdiobus accessors.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Altera Triple Speed Ethernet has a SGMII/1000BaseC PCS that can be
integrated in several ways. It can either be part of the TSE MAC's
address space, accessed through 32 bits accesses on the mapped mdio
device 0, or through a dedicated 16 bits register set.
This driver allows using the TSE PCS outside of altera TSE's driver,
since it can be used standalone by other MACs.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While phylink_pcs_ops :: pcs_get_state does return void, xpcs_get_state()
does check for a non-zero return code from xpcs_get_state_c37_sgmii()
and prints that as a message to the kernel log.
However, a non-zero return code from xpcs_read() is translated into
"return false" (i.e. zero as int) and the I/O error is therefore not
printed. Fix that.
Fixes: b97b5331b8 ("net: pcs: add C37 SGMII AN support for intel mGbE controller")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220720112057.3504398-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As stated by Russel King, miic_config() can be called as a result of
ethtool setting the configuration while the link is already up. Since
the speed is also set in this function, it could potentially modify
the current speed that is set. This will only happen if there is
no PHY present and we aren't using fixed-link mode.
Handle that by storing the current interface mode in the miic_port
structure and update the speed only if the interface mode is going to
be changed.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Link: https://lore.kernel.org/r/20220629122003.189397-1-clement.leger@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On failure, devm_platform_ioremap_resource() returns a ERR_PTR() value
and not NULL. Fix return value checking by using IS_ERR() and return
PTR_ERR() as error value.
Fixes: 7dc54d3b8d ("net: pcs: add Renesas MII converter driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Clément Léger <clement.leger@bootlin.com>
Link: https://lore.kernel.org/r/20220628131259.3109124-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a PCS driver for the MII converter that is present on the Renesas
RZ/N1 SoC. This MII converter is reponsible for converting MII to
RMII/RGMII or act as a MII pass-trough. Exposing it as a PCS allows to
reuse it in both the switch driver and the stmmac driver. Currently,
this driver only allows the PCS to be used by the dual Cortex-A7
subsystem since the register locking system is not used.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate lynx_pcs_config_1000basex() and lynx_pcs_config_sgmii() into
a single function. The differences between these two are:
- The value that the link timer is set to.
- The value of the IF_MODE register.
Everything else is identical.
This patch depends on "net: phylink: add QSGMII support to
phylink_mii_c22_pcs_encode_advertisement()".
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
