IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Facing below warning prints when we do wifi down in multiple VAPs scenario.
warning print:
ath11k c000000.wifi: No VIF found for vdev 2
...
ath11k c000000.wifi: No VIF found for vdev 0
In ath11k_mac_get_arvif_by_vdev_id(), we iterate all the radio to get the
arvif for the requested vdev_id through ath11k_mac_get_arvif().
ath11k_mac_get_arvif() throws a warning message if the given vdev_id is
not found in the given radio. So to avoid the warning message, add
the allocated_vdev_map cross check against the given vdev_id before using
ath11k_mac_get_arvif() to ensure that vdev_id is allocated in the
given radio.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-8-jouni@codeaurora.org
In scenario when a peer is disassociating, there could be
multiple places where a reo cmd ring is accessed, such as
during aggregation teardown, tid queue cleanup, etc.
When this happens during firmware recovery where accessing of FW/HW
resources/registers is not recommended, accessing reo cmd ring in
this case could lead to crash or undefined behaviour.
Hence avoid this by checking for corresponding flag to avoid
accessing reo cmd ring during firmware recovery.
Sample crash:
[ 3936.456050] Unhandled fault: imprecise external abort (0x1c06) at 0x54bb842a
[ 3936.456411] WARN: Access Violation!!!, Run "cat /sys/kernel/debug/qcom_debug_logs/tz_log" for more details
[ 3936.467997] pgd = b4474000
[ 3936.477440] [54bb842a] *pgd=6fa61831, *pte=7f95d59f, *ppte=7f95de7e
<snip>
[ 3937.177436] [<8030ab10>] (_raw_spin_unlock_bh) from [<7f5e9eb8>] (ath11k_hal_reo_cmd_send+0x440/0x458 [ath11k])
[ 3937.185730] [<7f5e9eb8>] (ath11k_hal_reo_cmd_send [ath11k]) from [<7f601c4c>] (ath11k_dp_tx_send_reo_cmd+0x2c/0xcc [ath11k])
[ 3937.195524] [<7f601c4c>] (ath11k_dp_tx_send_reo_cmd [ath11k]) from [<7f602f10>] (ath11k_peer_rx_tid_reo_update+0x84/0xbc [ath11k])
[ 3937.206984] [<7f602f10>] (ath11k_peer_rx_tid_reo_update [ath11k]) from [<7f605a9c>] (ath11k_dp_rx_ampdu_stop+0xa8/0x130 [ath11k])
[ 3937.218532] [<7f605a9c>] (ath11k_dp_rx_ampdu_stop [ath11k]) from [<7f5f6730>] (ath11k_mac_op_ampdu_action+0x6c/0x98 [ath11k])
[ 3937.230250] [<7f5f6730>] (ath11k_mac_op_ampdu_action [ath11k]) from [<c7b6e890>] (___ieee80211_stop_rx_ba_session+0x98/0x144 [mac80211])
[ 3937.241499] [<c7b6e890>] (___ieee80211_stop_rx_ba_session [mac80211]) from [<c7b6cdd8>] (ieee80211_sta_tear_down_BA_sessions+0x4c/0xf4 [)
[ 3937.253833] [<c7b6cdd8>] (ieee80211_sta_tear_down_BA_sessions [mac80211]) from [<c7b63460>] (ieee80211_sta_eosp+0x5b8/0x960 [mac80211])
[ 3937.266764] [<c7b63460>] (ieee80211_sta_eosp [mac80211]) from [<c7b66da8>] (__sta_info_flush+0x9c/0x134 [mac80211])
[ 3937.278826] [<c7b66da8>] (__sta_info_flush [mac80211]) from [<c7b7bd00>] (ieee80211_stop_ap+0x14c/0x28c [mac80211])
[ 3937.289240] [<c7b7bd00>] (ieee80211_stop_ap [mac80211]) from [<7f509cf0>] (__cfg80211_stop_ap+0x4c/0xd8 [cfg80211])
[ 3937.299629] [<7f509cf0>] (__cfg80211_stop_ap [cfg80211]) from [<7f4dddec>] (cfg80211_leave+0x24/0x30 [cfg80211])
[ 3937.310041] [<7f4dddec>] (cfg80211_leave [cfg80211]) from [<7f4de03c>] (cfg80211_netdev_notifier_call+0x174/0x48c [cfg80211])
[ 3937.320457] [<7f4de03c>] (cfg80211_netdev_notifier_call [cfg80211]) from [<80339928>] (notifier_call_chain+0x40/0x68)
[ 3937.331636] [<80339928>] (notifier_call_chain) from [<803399a8>] (raw_notifier_call_chain+0x14/0x1c)
[ 3937.342221] [<803399a8>] (raw_notifier_call_chain) from [<8073bb00>] (call_netdevice_notifiers+0xc/0x14)
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01240-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-7-jouni@codeaurora.org
Firmware crash is seen randomly, because of sending wrong vdev_id
in vdev_create command. This is due to free_vdev_map value being 0.
free_vdev_map is getting assigned after ieee80211_register_hw. In
some race conditions, add_interface api is getting called before
assigning value to free_vdev_map. Fix this by assigning free_vdev_map
before ieee80211_register_hw.
Also, moved ar->cc_freq_hz and ar->txmgmt_idr initialization before
ieee80211_register_hw to avoid such race conditions.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00948-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-6-jouni@codeaurora.org
Firmware blocks all data traffic until the key is plumbed. But, with
software encryption mode, key is never plumbed to firmware. Due to this,
a traffic failure in software encryption mode has been observed. Hence,
firmware has introduced a flag to differentiate software encryption
mode. This flag can be passed during vdev_start command.
Enable WMI_VDEV_START_HW_ENCRYPTION_DISABLED flag in vdev_start command
to notify firmware to disable hardware encryption for a vdev. This is set
if raw mode software encryption is enabled.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01421-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-5-jouni@codeaurora.org
Whenever ath11k is bootup with a user country already set, cfg80211
notifies this country info to ath11k soon after registration, where the
notification is sent to the firmware for fetching the rules of this user
country input.
Multiple race conditions could be seen in this scenario where a new
request is either lost as pointed in [1] or a new regd overwrites the
default regd provided by the firmware during bootup. Note that, the
default regd is used for intersection purpose and hence it should not be
overwritten.
The main reason as pointed by [1] is the usage of ATH11K_FLAG_REGISTERED
flag which is updated after completion of core registration, whereas the
reg notification from cfg80211 and wmi events for the corresponding
request can happen much before that. Since the ATH11K_FLAG_REGISTERED is
currently used to determine if the event containing reg rules belong to
default regd or for user request, there is a possibility of the default
regd getting overwritten.
Since the default reg rules will be received only once per pdev on
firmware load, the above flag based check can be replaced with a check
to see if default_regd is already set, so that we can now always update
the new_regd. Also if the new_regd is set, this will be always used to
update the reg rules for the registered phy.
[1] https://patchwork.kernel.org/project/linux-wireless/patch/1829665.1PRlr7bOQj@ripper/
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01460-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-4-jouni@codeaurora.org
During firmware recovery, the default reg rules which are
received via WMI_REG_CHAN_LIST_CC_EVENT can overwrite
the currently configured user regd.
See below snap for example,
root@OpenWrt:/# iw reg get | grep country
country FR: DFS-ETSI
country FR: DFS-ETSI
country FR: DFS-ETSI
country FR: DFS-ETSI
root@OpenWrt:/# echo assert > /sys/kernel/debug/ath11k/ipq8074\ hw2.0/simulate_f
w_crash
<snip>
[ 5290.471696] ath11k c000000.wifi1: pdev 1 successfully recovered
root@OpenWrt:/# iw reg get | grep country
country FR: DFS-ETSI
country US: DFS-FCC
country US: DFS-FCC
country US: DFS-FCC
In the above, the user configured country 'FR' is overwritten
when the rules of default country 'US' are received and updated during
recovery. Hence avoid processing of these rules in general
during firmware recovery as they have been already applied during
driver registration or after last set user country is configured.
This scenario applies for both AP and STA devices basically because
cfg80211 is not aware of the recovery and only the driver recovers, but
changing or resetting of the reg domain during recovery is not needed so
as to continue with the configured regdomain currently in use.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01460-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-3-jouni@codeaurora.org
Update the fields of pdev tx and tx firmware stats structure.
Missing fields resulted in wrong fw stats to be displayed as below.
root@OpenWrt:/# cat /sys/kernel/debug/ath11k/
ipq8074\ hw2.0/mac0/fw_stats/pdev_stats | grep Illegal
Illegal rate phy errors 36839112
Note that this struct was missing its members from initial driver
support and this change doesn't introduce/modify the structure for
firmware changes.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-2-jouni@codeaurora.org
Fix sending rx_buf_sz to ath11k_dp_tx_htt_rx_filter_setup()
to enable pktlog full or lite mode. Depending on mode update the
trace buffer with log type full/lite.
Pktlog lite is a lighter version of pktlog. This can be used to capture
PPDU stats. These are useful for firmware performance debugging.
pktlog lite dumps are enabled using,
echo "0x0 1" > ath11k/IPQ8074 hw2.0/mac0/pktlog_filter
Tested On: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01233-QCAHKSWPL_SILICONZ-1 v2
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-1-jouni@codeaurora.org
Add support for rx decapsulation offload by advertising
the support to mac80211 during registration. Also ensure
the frames have the RX_FLAG_8023 flag set in decap offload
frames before passing to mac80211.
Since the packets delivered to the driver are in 802.3 format, these
can be sent to the network core with minimal processing in mac80211.
This helps in releasing some CPU cycles in the host processor and
thereby improving the performance.
Two exceptions are made before passing decap frames, one is
for EAPOL packets since mac80211 8023 fast rx for the sta
is set only after authorization, other case is for multicast
packets to validate PN in mac80211. In both the cases the
decap frames are converted to 80211 frame and sent to mac80211.
Ethernet decap can be enabled by using frame_mode modparam:
insmod ath11k frame_mode=2
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00844-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721204217.120572-1-jouni@codeaurora.org
The ath11k_dbring_bufs_replenish() and ath11k_dbring_fill_bufs()
take a "gfp" parameter but they since they take spinlocks, the
allocations they do have to be atomic. This causes a bug because
ath11k_dbring_buf_setup passes GFP_KERNEL for the gfp flags.
The fix is to use GFP_ATOMIC and remove the unused parameters.
Fixes: bd6478559e27 ("ath11k: Add direct buffer ring support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210812070434.GE31863@kili
qmi tries to allocate a large contiguous dma memory at first,
on the AMD Ryzen platform it fails, then retries with small slices.
So set flag GFP_NOWARN to avoid flooding dmesg.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210823063258.37747-1-aaron.ma@canonical.com
There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code
should always use "flexible array members"[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
Refactor the code a bit according to the use of a flexible-array member in
struct scan_chan_list_params instead of a one-element array, and use the
struct_size() helper.
Also, save 25 (too many) bytes that were being allocated:
$ pahole -C channel_param drivers/net/wireless/ath/ath11k/reg.o
struct channel_param {
u8 chan_id; /* 0 1 */
u8 pwr; /* 1 1 */
u32 mhz; /* 2 4 */
/* Bitfield combined with next fields */
u32 half_rate:1; /* 4:16 4 */
u32 quarter_rate:1; /* 4:17 4 */
u32 dfs_set:1; /* 4:18 4 */
u32 dfs_set_cfreq2:1; /* 4:19 4 */
u32 is_chan_passive:1; /* 4:20 4 */
u32 allow_ht:1; /* 4:21 4 */
u32 allow_vht:1; /* 4:22 4 */
u32 allow_he:1; /* 4:23 4 */
u32 set_agile:1; /* 4:24 4 */
u32 psc_channel:1; /* 4:25 4 */
/* XXX 6 bits hole, try to pack */
u32 phy_mode; /* 8 4 */
u32 cfreq1; /* 12 4 */
u32 cfreq2; /* 16 4 */
char maxpower; /* 20 1 */
char minpower; /* 21 1 */
char maxregpower; /* 22 1 */
u8 antennamax; /* 23 1 */
u8 reg_class_id; /* 24 1 */
/* size: 25, cachelines: 1, members: 21 */
/* sum members: 23 */
/* sum bitfield members: 10 bits, bit holes: 1, sum bit holes: 6 bits */
/* last cacheline: 25 bytes */
} __attribute__((__packed__));
as previously, sizeof(struct scan_chan_list_params) was 32 bytes:
$ pahole -C scan_chan_list_params drivers/net/wireless/ath/ath11k/reg.o
struct scan_chan_list_params {
u32 pdev_id; /* 0 4 */
u16 nallchans; /* 4 2 */
struct channel_param ch_param[1]; /* 6 25 */
/* size: 32, cachelines: 1, members: 3 */
/* padding: 1 */
/* last cacheline: 32 bytes */
};
and now with the flexible array transformation it is just 8 bytes:
$ pahole -C scan_chan_list_params drivers/net/wireless/ath/ath11k/reg.o
struct scan_chan_list_params {
u32 pdev_id; /* 0 4 */
u16 nallchans; /* 4 2 */
struct channel_param ch_param[]; /* 6 0 */
/* size: 8, cachelines: 1, members: 3 */
/* padding: 2 */
/* last cacheline: 8 bytes */
};
This helps with the ongoing efforts to globally enable -Warray-bounds and
get us closer to being able to tighten the FORTIFY_SOURCE routines on
memcpy().
This issue was found with the help of Coccinelle and audited and fixed,
manually.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.10/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/109
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210823172159.GA25800@embeddedor
Firmware updates EEPROM support capability in QMI FW caps, send QMI BDF
download request message with file type EEPROM, to get caldata download
from EEPROM. Firmware takes more time to update cal data from EEPROM, so
increase QMI timeout.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721201927.100369-5-jouni@codeaurora.org
In current code, AHB/PCI uses two separate functions to download
BDF file. Refactor code and make a common function to send QMI BDF
download request for both AHB and PCI devices. This patch has no
functional change.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721201927.100369-3-jouni@codeaurora.org
Reuse board_size from hw_params, add cal_offset to hw params.
This patch is clean up only, there is no change in functionality.
cal_size was unused, so remove that.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721201927.100369-2-jouni@codeaurora.org
gcc-11 with the kernel address sanitizer prints a warning for this
driver:
In function 'ath11k_peer_assoc_h_vht',
inlined from 'ath11k_peer_assoc_prepare' at drivers/net/wireless/ath/ath11k/mac.c:1632:2:
drivers/net/wireless/ath/ath11k/mac.c:1164:13: error: 'ath11k_peer_assoc_h_vht_masked' reading 16 bytes from a region of size 4 [-Werror=stringop-overread]
1164 | if (ath11k_peer_assoc_h_vht_masked(vht_mcs_mask))
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath11k/mac.c: In function 'ath11k_peer_assoc_prepare':
drivers/net/wireless/ath/ath11k/mac.c:1164:13: note: referencing argument 1 of type 'const u16 *' {aka 'const short unsigned int *'}
drivers/net/wireless/ath/ath11k/mac.c:969:1: note: in a call to function 'ath11k_peer_assoc_h_vht_masked'
969 | ath11k_peer_assoc_h_vht_masked(const u16 vht_mcs_mask[NL80211_VHT_NSS_MAX])
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
According to analysis from gcc developers, this is a glitch in the
way gcc tracks the size of struct members. This should really get
fixed in gcc, but it's also easy to work around this instance
by changing the function prototype to no include the length of
the array.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=99673
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210322160253.4032422-5-arnd@kernel.org
Populate the below hw parameters as per the QCN9074 support
1. FFT bin size as two bytes
2. Maximum FFT bin count as 1024
3. Summary report pad size as 16
4. FFT report header length as 24
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721180809.90960-5-jouni@codeaurora.org
User was not able to configure the spectral with the FFT bin count 32.
In all supported platforms, the expected minimum FFT bin count is 32 but
it was wrongly defined as 64. This restrict the user to not configure
down to the actually supported minimum FFT bin count. So update the
minimum FFT bin count as 32.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721180809.90960-4-jouni@codeaurora.org
Below parameters have been identified as configurable across the platforms.
So to scale the spectral across the platforms, move these parameter
into hw param.
1. Maximum FFT bins
2. Summary report pad size
3. FFT report header length
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721180809.90960-3-jouni@codeaurora.org
In IPQ8074, actual FFT bin size is two bytes but hardware reports it
with extra pad size of two bytes for each FFT bin. So finally each FFT
bin advertise as four bytes size in the collected data. This FFT pad is
not advertised in IPQ6018 platform. To accommodate this different
behavior across the platforms, introduce the hw param fft_pad_sz and use
it in spectral process. Also group all the spectral params under the new
structure in hw param structure for scalable in future.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721180809.90960-2-jouni@codeaurora.org
For 160 MHz, nss_ratio_enabled flag is added to indicate firmware
supports sending NSS ratio information from firmware as a part of
service ready ext event. Extract this NSS ratio info from service
ready ext event and save this information in ath11k_pdev_cap to
calculate NSS ratio.
Current firmware configurations support two types of NSS ratio
which is WMI_NSS_RATIO_1_NSS for QCN9074 and WMI_NSS_RATIO_1BY2_NSS
for IPQ8074. Based on this two configuration, max supported
NSS getting calculated.
Move ath11k_peer_assoc_h_phymode() before ath11k_peer_assoc_h_vht()
to get arg->peer_phymode updated.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-00097-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01467-QCAHKSWPL_SILICONZ-1
Co-developed-by: Ganesh Sesetti <gseset@codeaurora.org>
Signed-off-by: Ganesh Sesetti <gseset@codeaurora.org>
Co-developed-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721173615.75637-2-jouni@codeaurora.org
Support setting fixed HE rate/gi/ltf values that we are now able to send
to the kernel using nl80211. The added code is reusing parts of the
existing code path already used for HT/VHT. The new helpers are
symmetric to how we do it for HT/VHT.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00235-QCAHKSWPL_SILICONZ-1
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Co-developed-by: Pradeep Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Pradeep Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721173615.75637-1-jouni@codeaurora.org
If monitor interface is enabled in co-exist mode, only local traffic are
captured. It's caused by missing monitor vdev in co-exist mode. So,
monitor mode clean up is done with separate Monitor APIs. For this,
introduce flags monitor_started and monitor_vdev_created.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01725-QCAHKSWPL_SILICONZ-1
Co-developed-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Co-developed-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721162053.46290-4-jouni@codeaurora.org
Add separate APIs for monitor_vdev_create/monitor_vdev_delete
and monitor_vdev_start/monitor_vdev_stop.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01725-QCAHKSWPL_SILICONZ-1
Co-developed-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Co-developed-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721162053.46290-3-jouni@codeaurora.org
This is to prepare for monitor mode clean up.
No functional changes are done.
Co-developed-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Co-developed-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721162053.46290-2-jouni@codeaurora.org
Idle Mode Power Save (IMPS) is a power saving mechanism which when called
by wcn36xx will cause the radio hardware to enter power collapse.
This particular call maps nicely to a simple conjunction/disjunction around
IEEE80211_CONF_CHANGE_IDLE and IEEE80211_CONF_IDLE.
Here we enter idle when we are not associated with an AP. The kernel will
incrementally toggle idle on/off in the process of trying to establish a
connection, thus saving power until we are connected to the AP again, at
which point we give way to BMPS if power_save is on.
We've validated that with IMPS an apq8039 device which has the wcn36xx
module loaded but, has not authenticated with an AP will get to VMIN on
suspend and will not without IMPS.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210909153320.2624649-1-bryan.odonoghue@linaro.org
Qcom documents suggest passing of negative values to the dump command,
however currently we convert from string to u32 not s32, so we cannot pass
a two's complement value to the firmware in this way.
There is in fact only one parameter which takes a two's complement value
<tigger threshold> in the antenna diversity switch command.
Downstream:
iwpriv wlan0 dump 71 3 <schedule period> <trigger threshold> <hysteresis value>
Upstream:
echo "71 3 <schedule period> <trigger threshold> <hysteresis value>" > /sys/kernel/debug/ieee80211/phy0/wcn36xx/dump
Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210909144428.2564650-3-bryan.odonoghue@linaro.org
We have been tracking a strange bug with Antenna Diversity Switching (ADS)
on wcn3680b for a while.
ADS is configured like this:
A. Via a firmware configuration table baked into the NV area.
1. Defines if ADS is enabled.
2. Defines which GPIOs are connected to which antenna enable pin.
3. Defines which antenna/GPIO is primary and which is secondary.
B. WCN36XX_CFG_VAL(ANTENNA_DIVERSITY, N)
N is a bitmask of available antenna.
Setting N to 3 indicates a bitmask of enabled antenna (1 | 2).
Obviously then we can set N to 1 or N to 2 to fix to a particular
antenna and disable antenna diversity.
C. WCN36XX_CFG_VAL(ASD_PROBE_INTERVAL, XX)
XX is the number of beacons between each antenna RSSI check.
Setting this value to 50 means, every 50 received beacons, run the
ADS algorithm.
D. WCN36XX_CFG_VAL(ASD_TRIGGER_THRESHOLD, YY)
YY is a two's complement integer which specifies the RSSI decibel
threshold below which ADS will run.
We default to -60db here, meaning a measured RSSI <= -60db will
trigger an ADS probe.
E. WCN36XX_CFG_VAL(ASD_RTT_RSSI_HYST_THRESHOLD, Z)
Z is a hysteresis value, indicating a delta which the RSSI must
exceed for the antenna switch to be valid.
For example if HYST_THRESHOLD == 3 AntennaId1-RSSI == -60db and
AntennaId-2-RSSI == -58db then firmware will not switch antenna.
The threshold needs to be -57db or better to satisfy the criteria.
F. A firmware feature bit also exists ANTENNA_DIVERSITY_SELECTION.
This feature bit is used by the firmware to report if
ANTENNA_DIVERSITY_SELECTION is supported. The host is not required to
toggle this bit to enable or disable ADS.
ADS works like this:
A. Every XX beacons the firmware switches to or remains on the primary
antenna.
B. The firmware then sends a Request-To-Send (RTS) packet to the AP.
C. The firmware waits for a Clear-To-Send (CTS) response from the AP.
D. The firmware then notes the received RSSI on the CTS packet.
E. The firmware then repeats steps A-D on the secondary antenna.
F. Subsequently if the RSSI on the measured antenna is better than
ASD_TRIGGER_THRESHOLD + the active antenna's RSSI then the
measured antenna becomes the active antenna.
G. If RSSI rises past ASD_TRIGGER_THRESHOLD then ADS doesn't run at
all even if there is a substantially better RSSI on the alternative
antenna.
What we have been observing is that the RTS packet is being sent but the
MAC address is a byte-swapped version of the target MAC. The ADS/RTS MAC is
corrupted only when the link is encrypted, if the AP is open the RTS MAC is
correct. Similarly if we configure the firmware to an RTS/CTS sequence for
regular data - the transmitted RTS MAC is correctly formatted.
Internally the wcn36xx firmware uses the indexes in the SMD commands to
populate and extract data from specific entries in an STA lookup table. The
AP's MAC appears a number of times in different indexes within this lookup
table, so the MAC address extracted for the data-transmit RTS and the MAC
address extracted for the ADS/RTS packet are not the same STA table index.
Our analysis indicates the relevant firmware STA table index is
"bssSelfStaIdx".
There is an STA populate function responsible for formatting the MAC
address of the bssSelfStaIdx including byte-swapping the MAC address.
Its clear then that the required STA populate command did not run for
bssSelfStaIdx.
So taking a look at the sequence of SMD commands sent to the firmware we
see the following downstream when moving from an unencrypted to encrypted
BSS setup.
- WLAN_HAL_CONFIG_BSS_REQ
- WLAN_HAL_CONFIG_STA_REQ
- WLAN_HAL_SET_STAKEY_REQ
Upstream in wcn36xx we have
- WLAN_HAL_CONFIG_BSS_REQ
- WLAN_HAL_SET_STAKEY_REQ
The solution then is to add the missing WLAN_HAL_CONFIG_STA_REQ between
WLAN_HAL_CONFIG_BSS_REQ and WLAN_HAL_SET_STAKEY_REQ.
No surprise WLAN_HAL_CONFIG_STA_REQ is the routine responsible for
populating the STA lookup table in the firmware and once done the MAC sent
by the ADS routine is in the correct byte-order.
This bug is apparent with ADS but it is also the case that any other
firmware routine that depends on the "bssSelfStaIdx" would retrieve
malformed data on an encrypted link.
Fixes: 3e977c5c523d ("wcn36xx: Define wcn3680 specific firmware parameters")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210909144428.2564650-2-bryan.odonoghue@linaro.org
Firmware sends delete_sta_context_ind when it detects the AP has gone
away in STA mode. Right now the handler for that indication only handles
AP mode; fix it to also handle STA mode.
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Li <benl@squareup.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210901180606.11686-1-benl@squareup.com
pdev_id in structure 'wmi_pdev_bss_chan_info_event' is wrongly placed
at the beginning. This causes invalid values in survey dump. Hence, align
the structure with the firmware.
Note: The firmware releases follow this order since the feature was
implemented. Also, it is not changing across the branches including
QCA6390.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720214922.118078-3-jouni@codeaurora.org
Survey dump statistics is not displaying channel rx and tx time because
the service flag is not enabled. Enable the service flag "bss_chan_info"
in wmi_resource_config to fetch and print the stats for the specific
pdev.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720214922.118078-2-jouni@codeaurora.org
The flag's purpose is not only meant for ATF configs. Rename atf_config
to flag1, so it can be used for future purposes.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720214922.118078-1-jouni@codeaurora.org
In 4addr, AP wired backbone to STA wired backbone ping fails due to ARP
request not getting answered. Here 4addr ARP multicast packet is sent in
3addr, so that 4addr STA not honouring the 3addr ARP multicast packet.
Fix this issue by sending out multicast packet in 4addr format, firmware
expects peer meta flag instead of vdev meta flag in Tx descriptor.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01641-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720213147.90042-2-jouni@codeaurora.org
Ath11k FW requires peer parameter WMI_PEER_USE_4ADDR to be set for
4-addr peers allowing 4-address frame transmission to those peers.
Add ath11k driver callback for sta_set_4addr() to queue new workq
set_4addr_wk only once based on new boolean, use_4addr_set.
sta_set_4addr() will be called during 4-addr STA association cases
applicable for both AP and STA modes.
In ath11k_sta_set_4addr_wk(),
AP mode:
WMI_PEER_USE_4ADDR will be set for the corresponding
associated 4-addr STA(s)
STA mode:
WMI_PEER_USE_4ADDR will be set for the AP to which the
4-addr STA got associated.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720213147.90042-1-jouni@codeaurora.org
extends the owl loader to fetch important pci initialization
values - which are stored together with the calibration data -
through the nvmem subsystem.
This allows for much faster WIFI/ath9k initializations on devices
that do not require to perform any post-processing (like XOR'ing/
reversal or unpacking)... than the current way through the
firmware_request which involves the filesystem/userspace.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/bc79ba1c6f6435000577bf1e5f4d7ebe18a8df97.1630157099.git.chunkeey@gmail.com
On most embedded ath9k devices (like range extenders,
routers, accesspoints, ...) the calibration data is
stored in a MTD partitions named "ART", or "caldata"/
"calibration".
Since commit 4b361cfa8624 ("mtd: core: add OTP nvmem provider support"):
All MTD partitions are all automatically available through
the nvmem subsystem.
This feature - together with an nvmem cell definition either
in the platform data or via device-tree allows drivers to get
the data necessary for initializing the WIFI, without having
to wait around for the filesystem and userspace to do
the extractions.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/f9b732b50a3453fadf3923cc75d365bae3505fe7.1630157099.git.chunkeey@gmail.com
- Add missing fields and remove some duplicate fields when printing a perf_event_attr.
- Fix hybrid config terms list corruption.
- Update kernel header copies, some resulted in new kernel features being
automagically added to 'perf trace' syscall/tracepoint argument id->string translators.
- Add a file generated during the documentation build to .gitignore.
- Add an option to build without libbfd, as some distros, like Debian consider
its ABI unstable.
- Add support to print a textual representation of IBS raw sample data in 'perf report'.
- Fix bpf 'perf test' sample mismatch reporting
- Fix passing arguments to stackcollapse report in a 'perf script' python script.
- Allow build-id with trailing zeros.
- Look for ImageBase in PE file to compute .text offset.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCYT0+hwAKCRCyPKLppCJ+
JxcPAQDO+iCKK/sF3TVN8f0T8xkFD6y8krBXPAtQHCAhVBeiqAD9F4R0VMX6nwy3
8rJnsNd2ODjywgFBO4uPy0N2fxBWjwo=
=/hH1
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-for-v5.15-2021-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull more perf tools updates from Arnaldo Carvalho de Melo:
- Add missing fields and remove some duplicate fields when printing a
perf_event_attr.
- Fix hybrid config terms list corruption.
- Update kernel header copies, some resulted in new kernel features
being automagically added to 'perf trace' syscall/tracepoint argument
id->string translators.
- Add a file generated during the documentation build to .gitignore.
- Add an option to build without libbfd, as some distros, like Debian
consider its ABI unstable.
- Add support to print a textual representation of IBS raw sample data
in 'perf report'.
- Fix bpf 'perf test' sample mismatch reporting
- Fix passing arguments to stackcollapse report in a 'perf script'
python script.
- Allow build-id with trailing zeros.
- Look for ImageBase in PE file to compute .text offset.
* tag 'perf-tools-for-v5.15-2021-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (25 commits)
tools headers UAPI: Update tools's copy of drm.h headers
tools headers UAPI: Sync drm/i915_drm.h with the kernel sources
tools headers UAPI: Sync linux/fs.h with the kernel sources
tools headers UAPI: Sync linux/in.h copy with the kernel sources
perf tools: Add an option to build without libbfd
perf tools: Allow build-id with trailing zeros
perf tools: Fix hybrid config terms list corruption
perf tools: Factor out copy_config_terms() and free_config_terms()
perf tools: Fix perf_event_attr__fprintf() missing/dupl. fields
perf tools: Ignore Documentation dependency file
perf bpf: Provide a weak btf__load_from_kernel_by_id() for older libbpf versions
tools include UAPI: Update linux/mount.h copy
perf beauty: Cover more flags in the move_mount syscall argument beautifier
tools headers UAPI: Sync linux/prctl.h with the kernel sources
tools include UAPI: Sync sound/asound.h copy with the kernel sources
tools headers UAPI: Sync linux/kvm.h with the kernel sources
tools headers UAPI: Sync x86's asm/kvm.h with the kernel sources
perf report: Add support to print a textual representation of IBS raw sample data
perf report: Add tools/arch/x86/include/asm/amd-ibs.h
perf env: Add perf_env__cpuid, perf_env__{nr_}pmu_mappings
...
- Remove DEFINE_SMP_CALL_CACHE_FUNCTION() which is a left over of the
original hotplug code and now causing trouble with the ARM64 cache
topology setup due to the pointless SMP function call. It's not longer
required as the hotplug callbacks are guaranteed to be invoked on the
upcoming CPU.
- Remove the deprecated and now unused CPU hotplug functions
- Rewrite the CPU hotplug API documentation
-----BEGIN PGP SIGNATURE-----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=uAYt
-----END PGP SIGNATURE-----
Merge tag 'smp-urgent-2021-09-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull CPU hotplug updates from Thomas Gleixner:
"Updates for the SMP and CPU hotplug:
- Remove DEFINE_SMP_CALL_CACHE_FUNCTION() which is a left over of the
original hotplug code and now causing trouble with the ARM64 cache
topology setup due to the pointless SMP function call.
It's not longer required as the hotplug callbacks are guaranteed to
be invoked on the upcoming CPU.
- Remove the deprecated and now unused CPU hotplug functions
- Rewrite the CPU hotplug API documentation"
* tag 'smp-urgent-2021-09-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Documentation: core-api/cpuhotplug: Rewrite the API section
cpu/hotplug: Remove deprecated CPU-hotplug functions.
thermal: Replace deprecated CPU-hotplug functions.
drivers: base: cacheinfo: Get rid of DEFINE_SMP_CALL_CACHE_FUNCTION()
Here is a single patch for 5.15-rc1, for the lkdtm misc driver.
It resolves a build issue that many people were hitting with your
current tree, and Kees and others felt would be good to get merged
before -rc1 comes out, to prevent them from having to constantly hit it
as many development trees restart on -rc1, not older -rc releases.
It has NOT been in linux-next, but has passed 0-day testing and looks
"obviously correct" when reviewing it locally :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYT4IaQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykQjwCgpMt1Tscv4Ek1iIigZTvygsgnBcgAniQH3nC7
iE5oyKRtQ3LolPGkAExd
=oC1V
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.15-rc1-lkdtm' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull misc driver fix from Greg KH:
"Here is a single patch for 5.15-rc1, for the lkdtm misc driver.
It resolves a build issue that many people were hitting with your
current tree, and Kees and others felt would be good to get merged
before -rc1 comes out, to prevent them from having to constantly hit
it as many development trees restart on -rc1, not older -rc releases.
It has NOT been in linux-next, but has passed 0-day testing and looks
'obviously correct' when reviewing it locally :)"
* tag 'char-misc-5.15-rc1-lkdtm' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
lkdtm: Use init_uts_ns.name instead of macros
Nothing bug, but probably needs to go in.
-----BEGIN PGP SIGNATURE-----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=BmmZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.15-1' of git://github.com/cminyard/linux-ipmi
Pull IPMI updates from Corey Minyard:
"A couple of very minor fixes for style and rate limiting.
Nothing big, but probably needs to go in"
* tag 'for-linus-5.15-1' of git://github.com/cminyard/linux-ipmi:
char: ipmi: use DEVICE_ATTR helper macro
ipmi: rate limit ipmi smi_event failure message
- Make sure the run-queue balance callback is invoked only on the outgoing CPU
-----BEGIN PGP SIGNATURE-----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=ExIs
-----END PGP SIGNATURE-----
Merge tag 'sched_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Borislav Petkov:
- Make sure the idle timer expires in hardirq context, on PREEMPT_RT
- Make sure the run-queue balance callback is invoked only on the
outgoing CPU
* tag 'sched_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Prevent balance_push() on remote runqueues
sched/idle: Make the idle timer expire in hard interrupt context
inconsistent state
- Avoid a potential null pointer dereference in the ww_mutex deadlock check
- Other smaller cleanups and optimizations
-----BEGIN PGP SIGNATURE-----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=3Eyw
-----END PGP SIGNATURE-----
Merge tag 'locking_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Borislav Petkov:
- Fix the futex PI requeue machinery to not return to userspace in
inconsistent state
- Avoid a potential null pointer dereference in the ww_mutex deadlock
check
- Other smaller cleanups and optimizations
* tag 'locking_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/rtmutex: Fix ww_mutex deadlock check
futex: Remove unused variable 'vpid' in futex_proxy_trylock_atomic()
futex: Avoid redundant task lookup
futex: Clarify comment for requeue_pi_wake_futex()
futex: Prevent inconsistent state and exit race
futex: Return error code instead of assigning it without effect
locking/rwsem: Add missing __init_rwsem() for PREEMPT_RT
Pull namei updates from Al Viro:
"Clearing fallout from mkdirat in io_uring series. The fix in the
kern_path_locked() patch plus associated cleanups"
* 'misc.namei' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
putname(): IS_ERR_OR_NULL() is wrong here
namei: Standardize callers of filename_create()
namei: Standardize callers of filename_lookup()
rename __filename_parentat() to filename_parentat()
namei: Fix use after free in kern_path_locked
-----BEGIN PGP SIGNATURE-----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=Y9tc
-----END PGP SIGNATURE-----
Merge tag '5.15-rc-cifs-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull smbfs updates from Steve French:
"cifs/smb3 updates:
- DFS reconnect fix
- begin creating common headers for server and client
- rename the cifs_common directory to smbfs_common to be more
consistent ie change use of the name cifs to smb (smb3 or smbfs is
more accurate, as the very old cifs dialect has long been
superseded by smb3 dialects).
In the future we can rename the fs/cifs directory to fs/smbfs.
This does not include the set of multichannel fixes nor the two
deferred close fixes (they are still being reviewed and tested)"
* tag '5.15-rc-cifs-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: properly invalidate cached root handle when closing it
cifs: move SMB FSCTL definitions to common code
cifs: rename cifs_common to smbfs_common
cifs: update FSCTL definitions
vduse driver supporting blk
virtio-vsock support for end of record with SEQPACKET
vdpa: mac and mq support for ifcvf and mlx5
vdpa: management netlink for ifcvf
virtio-i2c, gpio dt bindings
misc fixes, cleanups
NB: when merging this with
b542e383d8c0 ("eventfd: Make signal recursion protection a task bit")
from Linus' tree, replace eventfd_signal_count with
eventfd_signal_allowed, and drop the export of eventfd_wake_count from
("eventfd: Export eventfd_wake_count to modules").
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmE1+awPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpt6EIAJy0qrc62lktNA0IiIVJSLbUbTMmFj8MzkGR
8UxZdhpjWqBPJPyaOuNeksAqTGm/UAPEYx3C2c95Jhej7anFpy7dbCtIXcPHLJME
DjcJg+EDrlNCj8m0FcsHpHWsFzPMERJpyEZNxgB5WazQbv+yWhGrg2FN5DCnF0Ro
ZFYeKSVty148pQ0nHl8X0JM2XMtqit+O+LvKN2HQZ+fubh7BCzMxzkHY0QLHIzUS
UeZqd3Qm8YcbqnlX38P5D6k+NPiTEgknmxaBLkPxg6H3XxDAmaIRFb8Ldd1rsgy1
zTLGDiSGpVDIpawRnuEAzqJThV3Y5/MVJ1WD+mDYQ96tmhfp+KY=
=DBH/
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
- vduse driver ("vDPA Device in Userspace") supporting emulated virtio
block devices
- virtio-vsock support for end of record with SEQPACKET
- vdpa: mac and mq support for ifcvf and mlx5
- vdpa: management netlink for ifcvf
- virtio-i2c, gpio dt bindings
- misc fixes and cleanups
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (39 commits)
Documentation: Add documentation for VDUSE
vduse: Introduce VDUSE - vDPA Device in Userspace
vduse: Implement an MMU-based software IOTLB
vdpa: Support transferring virtual addressing during DMA mapping
vdpa: factor out vhost_vdpa_pa_map() and vhost_vdpa_pa_unmap()
vdpa: Add an opaque pointer for vdpa_config_ops.dma_map()
vhost-iotlb: Add an opaque pointer for vhost IOTLB
vhost-vdpa: Handle the failure of vdpa_reset()
vdpa: Add reset callback in vdpa_config_ops
vdpa: Fix some coding style issues
file: Export receive_fd() to modules
eventfd: Export eventfd_wake_count to modules
iova: Export alloc_iova_fast() and free_iova_fast()
virtio-blk: remove unneeded "likely" statements
virtio-balloon: Use virtio_find_vqs() helper
vdpa: Make use of PFN_PHYS/PFN_UP/PFN_DOWN helper macro
vsock_test: update message bounds test for MSG_EOR
af_vsock: rename variables in receive loop
virtio/vsock: support MSG_EOR bit processing
vhost/vsock: support MSG_EOR bit processing
...
