IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
There are 3 classes of switch families that the driver is aware of, as
far as mv88e6xxx_change_mtu() is concerned:
- MTU configuration is available per port. Here, the
chip->info->ops->port_set_jumbo_size() method will be present.
- MTU configuration is global to the switch. Here, the
chip->info->ops->set_max_frame_size() method will be present.
- We don't know how to change the MTU. Here, none of the above methods
will be present.
Switch families MV88E6165, MV88E6191, MV88E6220, MV88E6250 and MV88E6290
fall in category 3.
The blamed commit has adjusted the MTU for all 3 categories by EDSA_HLEN
(8 bytes), resulting in a new maximum MTU of 1492 being reported by the
driver for these switches.
I don't have the hardware to test, but I do have a MV88E6390 switch on
which I can simulate this by commenting out its .port_set_jumbo_size
definition from mv88e6390_ops. The result is this set of messages at
probe time:
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 1
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 2
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 3
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 4
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 5
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 6
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 7
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 8
It is highly implausible that there exist Ethernet switches which don't
support the standard MTU of 1500 octets, and this is what the DSA
framework says as well - the error comes from dsa_slave_create() ->
dsa_slave_change_mtu(slave_dev, ETH_DATA_LEN).
But the error messages are alarming, and it would be good to suppress
them.
As a consequence of this unlikeliness, we reimplement mv88e6xxx_get_max_mtu()
and mv88e6xxx_change_mtu() on switches from the 3rd category as follows:
the maximum supported MTU is 1500, and any request to set the MTU to a
value larger than that fails in dev_validate_mtu().
Fixes: b9c587fed61c ("dsa: mv88e6xxx: Include tagger overhead when setting MTU for DSA and CPU ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when dsa_slave_change_mtu() is called on a user port where
dev->max_mtu is 1500 (as returned by ds->ops->port_max_mtu()), the code
will stumble upon this check:
if (new_master_mtu > mtu_limit)
return -ERANGE;
because new_master_mtu is adjusted for the tagger overhead but mtu_limit
is not.
But it would be good if the logic went through, for example if the DSA
master really depends on an MTU adjustment to accept DSA-tagged frames.
To make the code pass through the check, we need to adjust mtu_limit for
the overhead as well, if the minimum restriction was caused by the DSA
user port's MTU (dev->max_mtu). A DSA user port MTU and a DSA master MTU
are always offset by the protocol overhead.
Currently no drivers return 1500 .port_max_mtu(), but this is only
temporary and a bug in itself - mv88e6xxx should have done that, but
since commit b9c587fed61c ("dsa: mv88e6xxx: Include tagger overhead when
setting MTU for DSA and CPU ports") it no longer does. This is a
preparation for fixing that.
Fixes: bfcb813203e6 ("net: dsa: configure the MTU for switch ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds SOCK_STREAM and SOCK_SEQPACKET tests for invalid buffer case.
It tries to read data to NULL buffer (data already presents in socket's
queue), then uses valid buffer. For SOCK_STREAM second read must return
data, because skbuff is not dropped, but for SOCK_SEQPACKET skbuff will
be dropped by kernel, and 'recv()' will return EAGAIN.
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This returns behaviour of SOCK_STREAM read as before skbuff usage. When
copying to user fails current skbuff won't be dropped, but returned to
sockets's queue. Technically instead of 'skb_dequeue()', 'skb_peek()' is
called and when skbuff becomes empty, it is removed from queue by
'__skb_unlink()'.
Fixes: 71dc9ec9ac7d ("virtio/vsock: replace virtio_vsock_pkt with sk_buff")
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Bobby Eshleman <bobby.eshleman@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we now no longer use 'skb->len' to update credit, there is no sense
to update skbuff state, because it is used only once after dequeue to
copy data and then will be released.
Fixes: 71dc9ec9ac7d ("virtio/vsock: replace virtio_vsock_pkt with sk_buff")
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Bobby Eshleman <bobby.eshleman@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'skb->len' can vary when we partially read the data, this complicates the
calculation of credit to be updated in 'virtio_transport_inc_rx_pkt()/
virtio_transport_dec_rx_pkt()'.
Also in 'virtio_transport_dec_rx_pkt()' we were miscalculating the
credit since 'skb->len' was redundant.
For these reasons, let's replace the use of skbuff state to calculate new
'rx_bytes'/'fwd_cnt' values with explicit value as input argument. This
makes code more simple, because it is not needed to change skbuff state
before each call to update 'rx_bytes'/'fwd_cnt'.
Fixes: 71dc9ec9ac7d ("virtio/vsock: replace virtio_vsock_pkt with sk_buff")
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Bobby Eshleman <bobby.eshleman@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the blamed commit, phy_ethtool_get_wol() and phy_ethtool_set_wol()
acquire phydev->lock, but the mscc phy driver implementations,
vsc85xx_wol_get() and vsc85xx_wol_set(), acquire the same lock as well,
resulting in a deadlock.
$ ip link set swp3 down
============================================
WARNING: possible recursive locking detected
mscc_felix 0000:00:00.5 swp3: Link is Down
--------------------------------------------
ip/375 is trying to acquire lock:
ffff3d7e82e987a8 (&dev->lock){+.+.}-{4:4}, at: vsc85xx_wol_get+0x2c/0xf4
but task is already holding lock:
ffff3d7e82e987a8 (&dev->lock){+.+.}-{4:4}, at: phy_ethtool_get_wol+0x3c/0x6c
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&dev->lock);
lock(&dev->lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by ip/375:
#0: ffffd43b2a955788 (rtnl_mutex){+.+.}-{4:4}, at: rtnetlink_rcv_msg+0x144/0x58c
#1: ffff3d7e82e987a8 (&dev->lock){+.+.}-{4:4}, at: phy_ethtool_get_wol+0x3c/0x6c
Call trace:
__mutex_lock+0x98/0x454
mutex_lock_nested+0x2c/0x38
vsc85xx_wol_get+0x2c/0xf4
phy_ethtool_get_wol+0x50/0x6c
phy_suspend+0x84/0xcc
phy_state_machine+0x1b8/0x27c
phy_stop+0x70/0x154
phylink_stop+0x34/0xc0
dsa_port_disable_rt+0x2c/0xa4
dsa_slave_close+0x38/0xec
__dev_close_many+0xc8/0x16c
__dev_change_flags+0xdc/0x218
dev_change_flags+0x24/0x6c
do_setlink+0x234/0xea4
__rtnl_newlink+0x46c/0x878
rtnl_newlink+0x50/0x7c
rtnetlink_rcv_msg+0x16c/0x58c
Removing the mutex_lock(&phydev->lock) calls from the driver restores
the functionality.
Fixes: 2f987d486610 ("net: phy: Add locks to ethtool functions")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230314153025.2372970-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Golle says:
====================
net: ethernet: mtk_eth_soc: minor SGMII fixes
This small series brings two minor fixes for the SGMII unit found in
MediaTek's router SoCs.
The first patch resets the PCS internal state machine on major
configuration changes, just like it is also done in MediaTek's SDK.
The second patch makes sure we only write values and restart AN if
actually needed, thus preventing unnesseray loss of an existing link
in some cases.
Both patches have previously been submitted as part of the series
"net: ethernet: mtk_eth_soc: various enhancements" which grew a bit
too big and it has correctly been criticized that some of the patches
should rather go as fixes to net-next.
This new series tries to address this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Only restart auto-negotiation and write link timer if actually
necessary. This prevents losing the link in case of minor
changes.
Fixes: 7e538372694b ("net: ethernet: mediatek: Re-add support SGMII")
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset the internal PCS state machine when changing interface mode.
This prevents confusing the state machine when changing interface
modes, e.g. from SGMII to 2500Base-X or vice-versa.
Fixes: 7e538372694b ("net: ethernet: mediatek: Re-add support SGMII")
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet length retrieved from skb data may be larger than
the actual socket buffer length (up to 9026 bytes). In such
case the cloned skb passed up the network stack will leak
kernel memory contents.
Fixes: d0cad871703b ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wenjia Zhang says:
====================
net/smc: Fixes 2023-03-01
The 1st patch solves the problem that CLC message initialization was
not properly reversed in error handling path. And the 2nd one fixes
the possible deadlock triggered by cancel_delayed_work_sync().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
CLC message initialization was not properly reversed in error handling path.
Reported-and-suggested-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum ASICs have a configurable limit on how deep into the packet
they parse. By default, the limit is 96 bytes.
There are several cases where this parsing depth is not enough and there
is a need to increase it. For example, timestamping of PTP packets and a
FIB multipath hash policy that requires hashing on inner fields. The
driver therefore maintains a reference count that reflects the number of
consumers that require an increased parsing depth.
During reload_down() the parsing depth reference count does not
necessarily drop to zero, but the parsing depth itself is restored to
the default during reload_up() when the firmware is reset. It is
therefore possible to end up in situations where the driver thinks that
the parsing depth was increased (reference count is non-zero), when it
is not.
Fix by making sure that all the consumers that increase the parsing
depth reference count also decrease it during reload_down().
Specifically, make sure that when the routing code is de-initialized it
drops the reference count if it was increased because of a FIB multipath
hash policy that requires hashing on inner fields.
Add a warning if the reference count is not zero after the driver was
de-initialized and explicitly reset it to zero during initialization for
good measures.
Fixes: 2d91f0803b84 ("mlxsw: spectrum: Add infrastructure for parsing configuration")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/9c35e1b3e6c1d8f319a2449d14e2b86373f3b3ba.1678727526.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This bug influences both st_nci_i2c_remove and st_nci_spi_remove.
Take st_nci_i2c_remove as an example.
In st_nci_i2c_probe, it called ndlc_probe and bound &ndlc->sm_work
with llt_ndlc_sm_work.
When it calls ndlc_recv or timeout handler, it will finally call
schedule_work to start the work.
When we call st_nci_i2c_remove to remove the driver, there
may be a sequence as follows:
Fix it by finishing the work before cleanup in ndlc_remove
CPU0 CPU1
|llt_ndlc_sm_work
st_nci_i2c_remove |
ndlc_remove |
st_nci_remove |
nci_free_device|
kfree(ndev) |
//free ndlc->ndev |
|llt_ndlc_rcv_queue
|nci_recv_frame
|//use ndlc->ndev
Fixes: 35630df68d60 ("NFC: st21nfcb: Add driver for STMicroelectronics ST21NFCB NFC chip")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230312160837.2040857-1-zyytlz.wz@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The test checks if (IPv4, IPv6) address pair properly conflict or not.
* IPv4
* 0.0.0.0
* 127.0.0.1
* IPv6
* ::
* ::1
If the IPv6 address is [::], the second bind() always fails.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paul Holzinger reported [0] that commit 5456262d2baa ("net: Fix
incorrect address comparison when searching for a bind2 bucket")
introduced a bind() regression. Paul also gave a nice repro that
calls two types of bind() on the same port, both of which now
succeed, but the second call should fail:
bind(fd1, ::, port) + bind(fd2, 127.0.0.1, port)
The cited commit added address family tests in three functions to
fix the uninit-value KMSAN report. [1] However, the test added to
inet_bind2_bucket_match_addr_any() removed a necessary conflict
check; the dual-stack wildcard address no longer conflicts with
an IPv4 non-wildcard address.
If tb->family is AF_INET6 and sk->sk_family is AF_INET in
inet_bind2_bucket_match_addr_any(), we still need to check
if tb has the dual-stack wildcard address.
Note that the IPv4 wildcard address does not conflict with
IPv6 non-wildcard addresses.
[0]: https://lore.kernel.org/netdev/e21bf153-80b0-9ec0-15ba-e04a4ad42c34@redhat.com/
[1]: https://lore.kernel.org/netdev/CAG_fn=Ud3zSW7AZWXc+asfMhZVL5ETnvuY44Pmyv4NPv-ijN-A@mail.gmail.com/
Fixes: 5456262d2baa ("net: Fix incorrect address comparison when searching for a bind2 bucket")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reported-by: Paul Holzinger <pholzing@redhat.com>
Link: https://lore.kernel.org/netdev/CAG_fn=Ud3zSW7AZWXc+asfMhZVL5ETnvuY44Pmyv4NPv-ijN-A@mail.gmail.com/
Reviewed-by: Eric Dumazet <edumazet@google.com>
Tested-by: Paul Holzinger <pholzing@redhat.com>
Reviewed-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If genphy_read_status fails then further access to the PHY may result
in unpredictable behavior. To prevent this bail out immediately if
genphy_read_status fails.
Fixes: 4223dbffed9f ("net: phy: smsc: Re-enable EDPD mode for LAN87xx")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/026aa4f2-36f5-1c10-ab9f-cdb17dda6ac4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RDMA is not supported in ice on a PF that has been added to a bonded
interface. To enforce this, when an interface enters a bond, we unplug
the auxiliary device that supports RDMA functionality. This unplug
currently happens in the context of handling the netdev bonding event.
This event is sent to the ice driver under RTNL context. This is causing
a deadlock where the RDMA driver is waiting for the RTNL lock to complete
the removal.
Defer the unplugging/re-plugging of the auxiliary device to the service
task so that it is not performed under the RTNL lock context.
Cc: stable@vger.kernel.org # 6.1.x
Reported-by: Jaroslav Pulchart <jaroslav.pulchart@gooddata.com>
Link: https://lore.kernel.org/netdev/CAK8fFZ6A_Gphw_3-QMGKEFQk=sfCw1Qmq0TVZK3rtAi7vb621A@mail.gmail.com/
Fixes: 5cb1ebdbc434 ("ice: Fix race condition during interface enslave")
Fixes: 4eace75e0853 ("RDMA/irdma: Report the correct link speed")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230310194833.3074601-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If no frames has been exchanged with a node for HSR_NODE_FORGET_TIME, the
node will be deleted from the node_db list. If a frame is sent to the node
after it is deleted, a netdev_err message for each slave interface is
produced. This should not happen with dan nodes because of supervision
frames, but can happen often with san nodes, which clutters the kernel
log. Since the hsr protocol does not support sans, this is only relevant
for the prp protocol.
Signed-off-by: Kristian Overskeid <koverskeid@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent commit eliminated a hack that adjusted the offset used for
many GSI registers. It became possible because we now specify all
GSI register offsets explicitly for every version of IPA.
Unfortunately, a large number of register offsets were *not* updated
as they should have been in that commit. For IPA v4.5+, the offset
for every GSI register *except* the two inter-EE interrupt masking
registers were supposed to have been reduced by 0xd000.
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # SM8350-HDK
Fixes: 59b12b1d27f3 ("net: ipa: kill gsi->virt_raw")
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20230310193709.1477102-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As my testing on the MCM MT7530 switch on MT7621 SoC shows, setting the PLL
frequency does not affect MII modes other than trgmii on port 5 and port 6.
So the assumption is that the operation here called "setting the PLL
frequency" actually sets the frequency of the TRGMII TX clock.
Make it so that it and the rest of the trgmii setup run only when the
trgmii mode is used.
Tested rgmii and trgmii modes of port 6 on MCM MT7530 on MT7621AT Unielec
U7621-06 and standalone MT7530 on MT7623NI Bananapi BPI-R2.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230310073338.5836-2-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove now incorrect comment regarding port 5 as GMAC5. This is supposed to
be supported since commit 38f790a80560 ("net: dsa: mt7530: Add support for
port 5") under mt7530_setup_port5().
Fixes: 38f790a80560 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230310073338.5836-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously we would divide total_left_rate by zero if num_vports
happened to be 1 because non_requested_count is calculated as
num_vports - req_count. Guard against this by validating num_vports at
the beginning and returning an error otherwise.
Found by Linux Verification Center (linuxtesting.org) with the SVACE
static analysis tool.
Fixes: bcd197c81f63 ("qed: Add vport WFQ configuration APIs")
Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230309201556.191392-1-d-tatianin@yandex-team.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When performing a stress test on SMC-R by rmmod mlx5_ib driver
during the wrk/nginx test, we found that there is a probability
of triggering a panic while terminating all link groups.
This issue dues to the race between smc_smcr_terminate_all()
and smc_buf_create().
smc_smcr_terminate_all
smc_buf_create
/* init */
conn->sndbuf_desc = NULL;
...
__smc_lgr_terminate
smc_conn_kill
smc_close_abort
smc_cdc_get_slot_and_msg_send
__softirqentry_text_start
smc_wr_tx_process_cqe
smc_cdc_tx_handler
READ(conn->sndbuf_desc->len);
/* panic dues to NULL sndbuf_desc */
conn->sndbuf_desc = xxx;
This patch tries to fix the issue by always to check the sndbuf_desc
before send any cdc msg, to make sure that no null pointer is
seen during cqe processing.
Fixes: 0b29ec643613 ("net/smc: immediate termination for SMCR link groups")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Link: https://lore.kernel.org/r/1678263432-17329-1-git-send-email-alibuda@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When using a PHC in shared between multiple hosts, the previous
frequency value may not be reset and could lead to host being unable to
compensate the offset with timecounter adjustments. To avoid such state
reset the hardware frequency of PHC to zero on init. Some refactoring is
needed to make code readable.
Fixes: 85036aee1938 ("bnxt_en: Add a non-real time mode to access NIC clock")
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230310151356.678059-1-vadfed@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) nft_parse_register_load() gets an incorrect datatype size
as input, from Jeremy Sowden.
2) incorrect maximum netlink attribute in nft_redir, also
from Jeremy.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nft_redir: correct value of inet type `.maxattrs`
netfilter: nft_redir: correct length for loading protocol registers
netfilter: nft_masq: correct length for loading protocol registers
netfilter: nft_nat: correct length for loading protocol registers
====================
Link: https://lore.kernel.org/r/20230309174655.69816-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Matthieu Baerts says:
====================
mptcp: fixes for 6.3
Patch 1 fixes a possible deadlock in subflow_error_report() reported by
lockdep. The report was in fact a false positive but the modification
makes sense and silences lockdep to allow syzkaller to find real issues.
The regression has been introduced in v5.12.
Patch 2 is a refactoring needed to be able to fix the two next issues.
It improves the situation and can be backported up to v6.0.
Patches 3 and 4 fix UaF reported by KASAN. It fixes issues potentially
visible since v5.7 and v5.19 but only reproducible until recently
(v6.0). These two patches depend on patch 2/7.
Patch 5 fixes the order of the printed values: expected vs seen values.
The regression has been introduced recently: v6.3-rc1.
Patch 6 adds missing ro_after_init flags. A previous patch added them
for other functions but these two have been missed. This previous patch
has been backported to stable versions (up to v5.12) so probably better
to do the same here.
Patch 7 fixes tcp_set_state() being called twice in a row since v5.10.
Patch 8 fixes another lockdep false positive issue but this time in
MPTCP PM code. Same here, some modifications in the code has been made
to silence this issue and help finding real ones later. This issue can
be seen since v6.2.
v1: https://lore.kernel.org/r/20230227-upstream-net-20230227-mptcp-fixes-v1-0-070e30ae4a8e@tessares.net
====================
Link: https://lore.kernel.org/r/20230227-upstream-net-20230227-mptcp-fixes-v2-0-47c2e95eada9@tessares.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Christoph reports a lockdep splat in the mptcp_subflow_create_socket()
error path, when such function is invoked by
mptcp_pm_nl_create_listen_socket().
Such code path acquires two separates, nested socket lock, with the
internal lock operation lacking the "nested" annotation. Adding that
in sock_release() for mptcp's sake only could be confusing.
Instead just add a new lockclass to the in-kernel msk socket,
re-initializing the lockdep infra after the socket creation.
Fixes: ad2171009d96 ("mptcp: fix locking for in-kernel listener creation")
Cc: stable@vger.kernel.org
Reported-by: Christoph Paasch <cpaasch@apple.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/354
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tcp_set_state() is called from tcp_done() already.
There is then no need to first set the state to TCP_CLOSE, then call
tcp_done().
Fixes: d582484726c4 ("mptcp: fix fallback for MP_JOIN subflows")
Cc: stable@vger.kernel.org
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/362
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add __ro_after_init labels for the variables tcp_prot_override and
tcpv6_prot_override, just like other variables adjacent to them, to
indicate that they are initialised from the init hooks and no writes
occur afterwards.
Fixes: b19bc2945b40 ("mptcp: implement delegated actions")
Cc: stable@vger.kernel.org
Fixes: 51fa7f8ebf0e ("mptcp: mark ops structures as ro_after_init")
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case of errors, the printed message had the expected and the seen
value inverted.
This patch simply correct the order: first the expected value, then the
one that has been seen.
Fixes: 10d4273411be ("selftests: mptcp: userspace: print error details if any")
Cc: stable@vger.kernel.org
Acked-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As reported by Christoph after having refactored the passive
socket initialization, the mptcp listener shutdown path is prone
to an UaF issue.
BUG: KASAN: use-after-free in _raw_spin_lock_bh+0x73/0xe0
Write of size 4 at addr ffff88810cb23098 by task syz-executor731/1266
CPU: 1 PID: 1266 Comm: syz-executor731 Not tainted 6.2.0-rc59af4eaa31c1f6c00c8f1e448ed99a45c66340dd5 #6
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x6e/0x91
print_report+0x16a/0x46f
kasan_report+0xad/0x130
kasan_check_range+0x14a/0x1a0
_raw_spin_lock_bh+0x73/0xe0
subflow_error_report+0x6d/0x110
sk_error_report+0x3b/0x190
tcp_disconnect+0x138c/0x1aa0
inet_child_forget+0x6f/0x2e0
inet_csk_listen_stop+0x209/0x1060
__mptcp_close_ssk+0x52d/0x610
mptcp_destroy_common+0x165/0x640
mptcp_destroy+0x13/0x80
__mptcp_destroy_sock+0xe7/0x270
__mptcp_close+0x70e/0x9b0
mptcp_close+0x2b/0x150
inet_release+0xe9/0x1f0
__sock_release+0xd2/0x280
sock_close+0x15/0x20
__fput+0x252/0xa20
task_work_run+0x169/0x250
exit_to_user_mode_prepare+0x113/0x120
syscall_exit_to_user_mode+0x1d/0x40
do_syscall_64+0x48/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
The msk grace period can legitly expire in between the last
reference count dropped in mptcp_subflow_queue_clean() and
the later eventual access in inet_csk_listen_stop()
After the previous patch we don't need anymore special-casing
msk listener socket cleanup: the mptcp worker will process each
of the unaccepted msk sockets.
Just drop the now unnecessary code.
Please note this commit depends on the two parent ones:
mptcp: refactor passive socket initialization
mptcp: use the workqueue to destroy unaccepted sockets
Fixes: 6aeed9045071 ("mptcp: fix race on unaccepted mptcp sockets")
Cc: stable@vger.kernel.org
Reported-and-tested-by: Christoph Paasch <cpaasch@apple.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/346
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Christoph reported a UaF at token lookup time after having
refactored the passive socket initialization part:
BUG: KASAN: use-after-free in __token_bucket_busy+0x253/0x260
Read of size 4 at addr ffff88810698d5b0 by task syz-executor653/3198
CPU: 1 PID: 3198 Comm: syz-executor653 Not tainted 6.2.0-rc59af4eaa31c1f6c00c8f1e448ed99a45c66340dd5 #6
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x6e/0x91
print_report+0x16a/0x46f
kasan_report+0xad/0x130
__token_bucket_busy+0x253/0x260
mptcp_token_new_connect+0x13d/0x490
mptcp_connect+0x4ed/0x860
__inet_stream_connect+0x80e/0xd90
tcp_sendmsg_fastopen+0x3ce/0x710
mptcp_sendmsg+0xff1/0x1a20
inet_sendmsg+0x11d/0x140
__sys_sendto+0x405/0x490
__x64_sys_sendto+0xdc/0x1b0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
We need to properly clean-up all the paired MPTCP-level
resources and be sure to release the msk last, even when
the unaccepted subflow is destroyed by the TCP internals
via inet_child_forget().
We can re-use the existing MPTCP_WORK_CLOSE_SUBFLOW infra,
explicitly checking that for the critical scenario: the
closed subflow is the MPC one, the msk is not accepted and
eventually going through full cleanup.
With such change, __mptcp_destroy_sock() is always called
on msk sockets, even on accepted ones. We don't need anymore
to transiently drop one sk reference at msk clone time.
Please note this commit depends on the parent one:
mptcp: refactor passive socket initialization
Fixes: 58b09919626b ("mptcp: create msk early")
Cc: stable@vger.kernel.org
Reported-and-tested-by: Christoph Paasch <cpaasch@apple.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/347
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 30e51b923e43 ("mptcp: fix unreleased socket in accept queue")
unaccepted msk sockets go throu complete shutdown, we don't need anymore
to delay inserting the first subflow into the subflow lists.
The reference counting deserve some extra care, as __mptcp_close() is
unaware of the request socket linkage to the first subflow.
Please note that this is more a refactoring than a fix but because this
modification is needed to include other corrections, see the following
commits. Then a Fixes tag has been added here to help the stable team.
Fixes: 30e51b923e43 ("mptcp: fix unreleased socket in accept queue")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Christoph reported a possible deadlock while the TCP stack
destroys an unaccepted subflow due to an incoming reset: the
MPTCP socket error path tries to acquire the msk-level socket
lock while TCP still owns the listener socket accept queue
spinlock, and the reverse dependency already exists in the
TCP stack.
Note that the above is actually a lockdep false positive, as
the chain involves two separate sockets. A different per-socket
lockdep key will address the issue, but such a change will be
quite invasive.
Instead, we can simply stop earlier the socket error handling
for orphaned or unaccepted subflows, breaking the critical
lockdep chain. Error handling in such a scenario is a no-op.
Reported-and-tested-by: Christoph Paasch <cpaasch@apple.com>
Fixes: 15cc10453398 ("mptcp: deliver ssk errors to msk")
Cc: stable@vger.kernel.org
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/355
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lorenzo Bianconi says:
====================
update xdp_features flag according to NIC re-configuration
Changes since v1:
- rebase on top of net tree
- remove NETDEV_XDP_ACT_NDO_XMIT_SG support in mlx5e driver
- always enable NETDEV_XDP_ACT_NDO_XMIT support in mlx5e driver
====================
Link: https://lore.kernel.org/r/cover.1678364612.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
XDP is supported only if enough queues are present, so when reconfiguring
the queues set xdp_features accordingly.
Fixes: 66c0e13ad236 ("drivers: net: turn on XDP features")
Suggested-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Matteo Croce <teknoraver@meta.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Take into account LRO and GRO configuration setting device xdp_features
flag. Consider channel rq_wq_type enabling rx scatter-gatter support in
xdp_features flag and disable NETDEV_XDP_ACT_NDO_XMIT_SG since it is not
supported yet by the driver.
Moreover always enable NETDEV_XDP_ACT_NDO_XMIT as the ndo_xdp_xmit
callback does not require to load a dummy xdp program on the NIC.
Fixes: 66c0e13ad236 ("drivers: net: turn on XDP features")
Co-developed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Take into account tx/rx queues reconfiguration setting device
xdp_features flag. Moreover consider NETIF_F_GRO flag in order to enable
ndo_xdp_xmit callback.
Fixes: 66c0e13ad236 ("drivers: net: turn on XDP features")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ena nic allows xdp just if enough hw queues are available for XDP.
Take into account queues configuration setting xdp_features.
Fixes: 66c0e13ad236 ("drivers: net: turn on XDP features")
Reviewed-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
thunderx nic allows xdp just if enough hw queues are available for XDP.
Take into account queues configuration setting xdp_features.
Fixes: 66c0e13ad236 ("drivers: net: turn on XDP features")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce xdp_set_features_flag utility routine in order to update
dynamically xdp_features according to the dynamic hw configuration via
ethtool (e.g. changing number of hw rx/tx queues).
Add xdp_clear_features_flag() in order to clear all xdp_feature flag.
Reviewed-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
