IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 1f0d5c911b64165c9754139a26c8c2fad352c132 upstream.
We expect 64-bit calculation result from below statement, however
in 32-bit machine, looped left shift operation on pgoff_t type
variable may cause overflow issue, fix it by forcing type cast.
page->index << PAGE_SHIFT;
Fixes: 26de9b117130 ("f2fs: avoid unnecessary updating inode during fsync")
Fixes: 0a2aa8fbb969 ("f2fs: refactor __exchange_data_block for speed up")
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 091c6e9c083f7ebaff00b37ad13562d51464d175 upstream.
When building with Clang + -Wtautological-pointer-compare:
drivers/net/wireless/realtek/rtlwifi/regd.c:389:33: warning: comparison
of address of 'rtlpriv->regd' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (wiphy == NULL || &rtlpriv->regd == NULL)
~~~~~~~~~^~~~ ~~~~
1 warning generated.
The address of an array member is never NULL unless it is the first
struct member so remove the unnecessary check. This was addressed in
the staging version of the driver in commit f986978b32b3 ("Staging:
rtlwifi: remove unnecessary NULL check").
While we are here, fix the following checkpatch warning:
CHECK: Comparison to NULL could be written "!wiphy"
35: FILE: drivers/net/wireless/realtek/rtlwifi/regd.c:389:
+ if (wiphy == NULL)
Fixes: 0c8173385e54 ("rtl8192ce: Add new driver")
Link:https://github.com/ClangBuiltLinux/linux/issues/750
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fed8d8c7a6dc2a76d7764842853d81c770b0788e upstream.
The driver does the wrong thing when cs_change is set on a non-last
xfer in a message. When cs_change is set, the driver deactivates the
CS and leaves it off until a later xfer again has cs_change set whereas
it should be briefly toggling CS off and on again.
This patch brings the behaviour of the driver back in line with the
documentation and common sense. The delay of 10 us is the same as is
used by the default spi_transfer_one_message() function in spi.c.
[gregory: rebased on for-5.5 from spi tree]
Fixes: 8090d6d1a415 ("spi: atmel: Refactor spi-atmel to use SPI framework queue")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191018153504.4249-1-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a719a75a7761e4139dd099330d9fe3589d844f9b upstream.
spi_nor_read() assigns the result of 'ssize_t spi_nor_read_data()'
to the 'int ret' variable, while 'ssize_t' is a 64-bit type and *int*
is a 32-bit type on the 64-bit machines. This silent truncation isn't
really valid, so fix up the variable's type.
Fixes: 59451e1233bd ("mtd: spi-nor: change return value of read/write")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 704c6c80fb471d1bb0ef0d61a94617d1d55743cd upstream.
>From isp_video_release(), &isp->video_lock is held and subsequent
vb2_fop_release() tries to lock vdev->lock which is same with the
previous one. Replace vb2_fop_release() with _vb2_fop_release() to
fix the recursive locking.
Fixes: 1380f5754cb0 ("[media] videobuf2: Add missing lock held on vb2_fop_release")
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74887542fdcc92ad06a48c0cca17cdf09fc8aa00 upstream.
Per Documentation/DMA-API-HOWTO.txt,
To unmap a scatterlist, just call:
dma_unmap_sg(dev, sglist, nents, direction);
.. note::
The 'nents' argument to the dma_unmap_sg call must be
the _same_ one you passed into the dma_map_sg call,
it should _NOT_ be the 'count' value _returned_ from the
dma_map_sg call.
However in the driver, priv->nent is directly assigned with value
returned from dma_map_sg, and dma_unmap_sg use priv->nent for unmap,
this breaks the API usage.
So introduce a new entry orig_nent to remember 'nents'.
Fixes: da3564ee027e ("pch_uart: add multi-scatter processing")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1573623259-6339-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 596fd8dffb745afcebc0ec6968e17fe29f02044c upstream.
The dmaengine_prep_slave_sg needs to use sg count returned
by dma_map_sg, not use sport->dma_tx_nents, because the return
value of dma_map_sg is not always same with "nents".
Fixes: b4cdc8f61beb ("serial: imx: add DMA support for imx6q")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1573108875-26530-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d72dcef891030545f39ad386a30cf91df517fb2 upstream.
On PowerNV the PCIe topology is (currently) managed by the powernv platform
code in Linux in cooperation with the platform firmware. Linux's native
PCIe port service drivers operate independently of both and this can cause
problems.
The main issue is that the portbus driver will conflict with the platform
specific hotplug driver (pnv_php) over ownership of the MSI used to notify
the host when a hotplug event occurs. The portbus driver claims this MSI on
behalf of the individual port services because the same interrupt is used
for hotplug events, PMEs (on root ports), and link bandwidth change
notifications. The portbus driver will always claim the interrupt even if
the individual port service drivers, such as pciehp, are compiled out.
The second, bigger, problem is that the hotplug port service driver
fundamentally does not work on PowerNV. The platform assumes that all
PCI devices have a corresponding arch-specific handle derived from the DT
node for the device (pci_dn) and without one the platform will not allow
a PCI device to be enabled. This problem is largely due to historical
baggage, but it can't be resolved without significant re-factoring of the
platform PCI support.
We can fix these problems in the interim by setting the
"pcie_ports_disabled" flag during platform initialisation. The flag
indicates the platform owns the PCIe ports which stops the portbus driver
from being registered.
This does have the side effect of disabling all port services drivers
that is: AER, PME, BW notifications, hotplug, and DPC. However, this is
not a huge disadvantage on PowerNV since these services are either unused
or handled through other means.
Fixes: 66725152fb9f ("PCI/hotplug: PowerPC PowerNV PCI hotplug driver")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191118065553.30362-1-oohall@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d7bf41fafa5b5ddd4c13eb39446b0045f0a8167 upstream.
Unlike the normal SIOCOUTQ, SIOCOUTQNSD was never handled in compat
mode. Add it to the common socket compat handler along with similar
ones.
Fixes: 2f4e1b397097 ("tcp: ioctl type SIOCOUTQNSD returns amount of data not sent")
Cc: Eric Dumazet <edumazet@google.com>
Cc: netdev@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e21be0d1d7bd7f78a77613f6bcb6965e72b22fc1 upstream.
Save and restore top PLL related configuration registers for big (APLL)
and LITTLE (KPLL) cores during suspend/resume cycle. So far, CPU clocks
were reset to default values after suspend/resume cycle and performance
after system resume was affected when performance governor has been selected.
Fixes: 773424326b51 ("clk: samsung: exynos5420: add more registers to restore list")
Signed-off-by: Marian Mihailescu <mihailescu2m@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73668309215285366c433489de70d31362987be9 upstream.
mei client bus added the client protocol version to the device alias,
but ABI documentation was not updated.
Fixes: b26864cad1c9 (mei: bus: add client protocol version to the device alias)
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191008005735.12707-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b742763d9d4195e823ae6ece760c9ed0500c1dc upstream.
This was found only after the whole thing with the inline functions, but
the compiler actually found something. The value of the `bias` (in
adis16480_get_calibbias()) should only be set if the read operation was
successful.
No actual known problem occurs as users of this function all
ultimately check the return value. Hence probably not stable material.
Fixes: 2f3abe6cbb6c9 ("iio:imu: Add support for the ADIS16480 and similar IMUs")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 176a7fca81c5090a7240664e3002c106d296bf31 upstream.
Some of ASUS laptops like UX431FL keyboard backlight cannot be set to
brightness 0. According to ASUS' information, the brightness should be
0x80 ~ 0x83. This patch fixes it by following the logic.
Fixes: e9809c0b9670 ("asus-wmi: add keyboard backlight support")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Reviewed-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 465f4edaecc6c37f81349233e84d46246bcac11a upstream.
If an attached disk with protection information enabled is reformatted
to Type 0 the revalidation code does not clear the original protection
type and subsequent accesses will keep setting RDPROTECT/WRPROTECT.
Set the protection type to 0 if the disk reports PROT_EN=0 in READ
CAPACITY(16).
[mkp: commit desc]
Fixes: fe542396da73 ("[SCSI] sd: Ensure we correctly disable devices with unknown protection type")
Link: https://lore.kernel.org/r/1578532344-101668-1-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 529244bd1afc102ab164429d338d310d5d65e60d upstream.
Doing an add/remove/add on a SCSI device in an enclosure leads to an oops
caused by poisoned values in the enclosure device list pointers. The
reason is because we are keeping the enclosure device across the enclosed
device add/remove/add but the current code is doing a
device_add/device_del/device_add on it. This is the wrong thing to do in
sysfs, so fix it by not doing a device_del on the enclosure device simply
because of a hot remove of the drive in the slot.
[mkp: added missing email addresses]
Fixes: 43d8eb9cfd0a ("[SCSI] ses: add support for enclosure component hot removal")
Link: https://lore.kernel.org/r/1578532892.3852.10.camel@HansenPartnership.com
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reported-by: Luo Jiaxing <luojiaxing@huawei.com>
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e88982ad1bb12db699de96fbc07096359ef6176c upstream.
The code added by this patch is similar to the code that already exists in
ibmvscsis_determine_resid(). This patch has been tested by running the
following command:
strace sg_raw -r 1k /dev/sdb 12 00 00 00 60 00 -o inquiry.bin |&
grep resid=
Link: https://lore.kernel.org/r/20191105214632.183302-1-bvanassche@acm.org
Fixes: a42d985bd5b2 ("ib_srpt: Initial SRP Target merge for v3.3-rc1")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Honggang Li <honli@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7935799e041ae10d380d04ea23868240f082bd11 upstream.
Clang warns:
../fs/cifs/smb2file.c:70:3: warning: misleading indentation; statement
is not part of the previous 'if' [-Wmisleading-indentation]
if (oparms->tcon->use_resilient) {
^
../fs/cifs/smb2file.c:66:2: note: previous statement is here
if (rc)
^
1 warning generated.
This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
Fixes: 592fafe644bf ("Add resilienthandles mount parm")
Link: https://github.com/ClangBuiltLinux/linux/issues/826
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ed0a1d563903bdb4b4c36c58c4d9c1bcb23a6e6 upstream.
The supervision frame is L2 frame.
When supervision frame is created, hsr module doesn't set network header.
If tap routine is enabled, dev_queue_xmit_nit() is called and it checks
network_header. If network_header pointer wasn't set(or invalid),
it resets network_header and warns.
In order to avoid unnecessary warning message, resetting network_header
is needed.
Test commands:
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst
ip link set veth0 up
ip link set veth2 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set veth3 up
ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3
ip netns exec nst ip a a 192.168.100.2/24 dev hsr1
ip netns exec nst ip link set hsr1 up
tcpdump -nei veth0
Splat looks like:
[ 175.852292][ C3] protocol 88fb is buggy, dev veth0
Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d935bd50dd14a7714cbdba9a76435dbb56edb1ae upstream.
When a GPIO offset in a lookup table is out-of-range, the printed error
message (1) does not include the actual out-of-range value, and (2)
contains an off-by-one error in the upper bound.
Avoid user confusion by also printing the actual GPIO offset, and
correcting the upper bound of the range.
While at it, use "%u" for unsigned int.
Sample impact:
-requested GPIO 0 is out of range [0..32] for chip e6052000.gpio
+requested GPIO 0 (45) is out of range [0..31] for chip e6052000.gpio
Fixes: 2a3cf6a3599e9015 ("gpiolib: return -ENOENT if no GPIO mapping exists")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191127095919.4214-1-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d4e6ccd1fb09dbfbc49746ca82bd5c25ad4bfe4 upstream.
This adds the missing teardown step that removes the device link from
the group when the device addition fails.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Fixes: 797a8b4d768c5 ("iommu: Handle default domain attach failure")
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 653997eeecef95c3ead4fba1b2d27e6a5854d6cd upstream.
Alarm registers high byte was reserved for other functions.
This add mask in alarm registers operation functions.
This also fix error condition in interrupt handler.
Fixes: fc2979118f3f ("rtc: mediatek: Add MT6397 RTC driver")
Signed-off-by: Ran Bi <ran.bi@mediatek.com>
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Link: https://lore.kernel.org/r/1576057435-3561-6-git-send-email-hsin-hsiung.wang@mediatek.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d3ff0950e2b40dc861b1739029649d03f591820 upstream.
If dccp_feat_push_change fails, we forget free the mem
which is alloced by kmemdup in dccp_feat_clone_sp_val.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e8ef967a54f4 ("dccp: Registration routines for changing feature values")
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7bc04c5c2cc467c5b40f2b03ba08da174a0d5fa7 upstream.
When remounting with debug_want_extra_isize, we were not performing the
same checks that we do during a normal mount. That allowed us to set a
value for s_want_extra_isize that reached outside the s_inode_size.
Fixes: e2b911c53584 ("ext4: clean up feature test macros with predicate functions")
Reported-by: syzbot+f584efa0ac7213c226b7@syzkaller.appspotmail.com
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Barret Rhoden <brho@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
[bwh: Backported to 4.9: The debug_want_extra_isize mount option is not
supported]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f3ef5c25cc762687a7341c18cbea5af54461407 upstream.
In the implementation of i2400m_op_rfkill_sw_toggle() the allocated
buffer for cmd should be released before returning. The
documentation for i2400m_msg_to_dev() says when it returns the buffer
can be reused. Meaning cmd should be released in either case. Move
kfree(cmd) before return to be reached by all execution paths.
Fixes: 2507e6ab7a9a ("wimax: i2400: fix memory leak")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2507e6ab7a9a440773be476141a255934468c5ef upstream.
In i2400m_op_rfkill_sw_toggle cmd buffer should be released along with
skb response.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e493173b7841259a08c5c8e5cbe90adb349da7e upstream.
The Layer 2 Update frame is used to update bridges when a station roams
to another AP even if that STA does not transmit any frames after the
reassociation. This behavior was described in IEEE Std 802.11F-2003 as
something that would happen based on MLME-ASSOCIATE.indication, i.e.,
before completing 4-way handshake. However, this IEEE trial-use
recommended practice document was published before RSN (IEEE Std
802.11i-2004) and as such, did not consider RSN use cases. Furthermore,
IEEE Std 802.11F-2003 was withdrawn in 2006 and as such, has not been
maintained amd should not be used anymore.
Sending out the Layer 2 Update frame immediately after association is
fine for open networks (and also when using SAE, FT protocol, or FILS
authentication when the station is actually authenticated by the time
association completes). However, it is not appropriate for cases where
RSN is used with PSK or EAP authentication since the station is actually
fully authenticated only once the 4-way handshake completes after
authentication and attackers might be able to use the unauthenticated
triggering of Layer 2 Update frame transmission to disrupt bridge
behavior.
Fix this by postponing transmission of the Layer 2 Update frame from
station entry addition to the point when the station entry is marked
authorized. Similarly, send out the VLAN binding update only if the STA
entry has already been authorized.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 4.9: adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30ca1aa536211f5ac3de0173513a7a99a98a97f3 upstream.
Make ieee80211_send_layer2_update() a common function so other drivers
can re-use it.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[bwh: Backported to 4.9 as dependency of commit 3e493173b784
"mac80211: Do not send Layer 2 Update frame before authorization":
- Retain type-casting of skb_put() return value
- Adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82034c23fcbc2389c73d97737f61fa2dd6526413 upstream.
Commit 15122ee2c515 ("arm64: Enforce BBM for huge IO/VMAP mappings")
disallowed block mappings for ioremap since that code does not honor
break-before-make. The same APIs are also used for permission updating
though and the extra checks prevent the permission updates from happening,
even though this should be permitted. This results in read-only permissions
not being fully applied. Visibly, this can occasionaly be seen as a failure
on the built in rodata test when the test data ends up in a section or
as an odd RW gap on the page table dump. Fix this by using
pgattr_change_is_safe instead of p*d_present for determining if the
change is permitted.
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Fixes: 15122ee2c515 ("arm64: Enforce BBM for huge IO/VMAP mappings")
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15122ee2c515a253b0c66a3e618bc7ebe35105eb upstream.
ioremap_page_range doesn't honour break-before-make and attempts to put
down huge mappings (using p*d_set_huge) over the top of pre-existing
table entries. This leads to us leaking page table memory and also gives
rise to TLB conflicts and spurious aborts, which have been seen in
practice on Cortex-A75.
Until this has been resolved, refuse to put block mappings when the
existing entry is found to be present.
Fixes: 324420bf91f60 ("arm64: add support for ioremap() block mappings")
Reported-by: Hanjun Guo <hanjun.guo@linaro.org>
Reported-by: Lei Li <lious.lilei@hisilicon.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is preparation for the following backported fixes. It was done
upstream as part of commit 20a004e7b017 "arm64: mm: Use
READ_ONCE/WRITE_ONCE when accessing page tables", the rest of which
does not seem suitable for stable.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 193383043f14a398393dc18bae8380f7fe665ec3 upstream.
Instead of open coding the generation of page table entries, use the
macros/functions that exist for this - pfn_p*d and p*d_populate. Most
code in the kernel already uses these macros, this patch tries to fix
up the few places that don't. This is useful for the next patch in this
series, which needs to change the page table entry logic, and it's
better to have that logic in one place.
The KVM extended ID map is special, since we're creating a level above
CONFIG_PGTABLE_LEVELS and the required function isn't available. Leave
it as is and add a comment to explain it. (The normal kernel ID map code
doesn't need this change because its page tables are created in assembly
(__create_page_tables)).
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[bwh: Backported to 4.9: adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e98216b52176ba2bfa4bdb02f178f4d08832d465 upstream.
Now that we take care not manipulate the live kernel page tables in a
way that may lead to TLB conflicts, the case where a table mapping is
replaced by a block mapping can no longer occur. So remove the handling
of this at the PUD and PMD levels, and instead, BUG() on any occurrence
of live kernel page table manipulations that modify anything other than
the permission bits.
Since mark_rodata_ro() is the only caller where the kernel mappings that
are being manipulated are actually live, drop the various conditional
flush_tlb_all() invocations, and add a single call to mark_rodata_ro()
instead.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abd39c6ded9db53aa44c2540092bdd5fb6590fa8 upstream.
Observed crash in some scenarios when assertion has occurred,
this is because hw structure is freed and is tried to get
accessed in some functions where null check is already
present. So, avoided the crash by making the hw to NULL after
freeing.
Signed-off-by: Sanjay Konduri <sanjay.konduri@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad312f95d41c9de19313c51e388c4984451c010f upstream.
The select() implementation is carefully tuned to put a sensible amount
of data on the stack for holding a copy of the user space fd_set, but
not too large to risk overflowing the kernel stack.
When building a 32-bit kernel with clang, we need a little more space
than with gcc, which often triggers a warning:
fs/select.c:619:5: error: stack frame size of 1048 bytes in function 'core_sys_select' [-Werror,-Wframe-larger-than=]
int core_sys_select(int n, fd_set __user *inp, fd_set __user *outp,
I experimentally found that for 32-bit ARM, reducing the maximum stack
usage by 64 bytes keeps us reliably under the warning limit again.
Link: http://lkml.kernel.org/r/20190307090146.1874906-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3499e87ea0413ee5b2cc028f4c8ed4d424bc7f98 upstream.
clang inlines the dev_ethtool() more aggressively than gcc does, leading
to a larger amount of used stack space:
net/core/ethtool.c:2536:24: error: stack frame size of 1216 bytes in function 'dev_ethtool' [-Werror,-Wframe-larger-than=]
Marking the sub-functions that require the most stack space as
noinline_for_stack gives us reasonable behavior on all compilers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9e635c2851df6caee651e589fbf937b637973c91 ]
hidraw and uhid device nodes are always available for writing so we should
always report EPOLLOUT and EPOLLWRNORM bits, not only in the cases when
there is nothing to read.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: be54e7461ffdc ("HID: uhid: Fix returning EPOLLOUT from uhid_char_poll")
Fixes: 9f3b61dc1dd7b ("HID: hidraw: Fix returning EPOLLOUT from hidraw_poll")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f3b61dc1dd7b81e99e7ed23776bb64a35f39e1a ]
When polling a connected /dev/hidrawX device, it is useful to get the
EPOLLOUT when writing is possible. Since writing is possible as soon as
the device is connected, always return it.
Right now EPOLLOUT is only returned when there are also input reports
are available. This works if devices start sending reports when
connected, but some HID devices might need an output report first before
sending any input reports. This change will allow using EPOLLOUT here as
well.
Fixes: 378b80370aa1 ("hidraw: Return EPOLLOUT from hidraw_poll")
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 378b80370aa1fe50f9c48a3ac8af3e416e73b89f ]
Always return EPOLLOUT from hidraw_poll when a device is connected.
This is safe since writes are always possible (but will always block).
hidraw does not support non-blocking writes and instead always calls
blocking backend functions on write requests. Hence, so far, a call to
poll never returned EPOLLOUT, which confuses tools like socat.
Signed-off-by: Fabian Henneke <fabian.henneke@gmail.com>
In-reply-to: <CA+hv5qkyis03CgYTWeWX9cr0my-d2Oe+aZo+mjmWRXgjrGqyrw@mail.gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bc8a76a152c5f9ef3b48104154a65a68a8b76946 upstream.
Intel ID: PSIRT-TA-201910-001
CVEID: CVE-2019-14615
Intel GPU Hardware prior to Gen11 does not clear EU state
during a context switch. This can result in information
leakage between contexts.
For Gen8 and Gen9, hardware provides a mechanism for
fast cleardown of the EU state, by issuing a PIPE_CONTROL
with bit 27 set. We can use this in a context batch buffer
to explicitly cleardown the state on every context switch.
As this workaround is already in place for gen8, we can borrow
the code verbatim for Gen9.
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Cc: Kumar Valsan Prathap <prathap.kumar.valsan@intel.com>
Cc: Chris Wilson <chris.p.wilson@intel.com>
Cc: Balestrieri Francesco <francesco.balestrieri@intel.com>
Cc: Bloomfield Jon <jon.bloomfield@intel.com>
Cc: Dutt Sudeep <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22dad713b8a5ff488e07b821195270672f486eb2 upstream.
The set uadt functions assume lineno is never NULL, but it is in
case of ip_set_utest().
syzkaller managed to generate a netlink message that calls this with
LINENO attr present:
general protection fault: 0000 [#1] PREEMPT SMP KASAN
RIP: 0010:hash_mac4_uadt+0x1bc/0x470 net/netfilter/ipset/ip_set_hash_mac.c:104
Call Trace:
ip_set_utest+0x55b/0x890 net/netfilter/ipset/ip_set_core.c:1867
nfnetlink_rcv_msg+0xcf2/0xfb0 net/netfilter/nfnetlink.c:229
netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477
nfnetlink_rcv+0x1ba/0x460 net/netfilter/nfnetlink.c:563
pass a dummy lineno storage, its easier than patching all set
implementations.
This seems to be a day-0 bug.
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Reported-by: syzbot+34bd2369d38707f3f4a7@syzkaller.appspotmail.com
Fixes: a7b4f989a6294 ("netfilter: ipset: IP set core support")
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b789577f655060d98d20ed0c6f9fbd469d6ba63 upstream.
We get crash when the targets checkentry function tries to make
use of the network namespace pointer for arptables.
When the net pointer got added back in 2010, only ip/ip6/ebtables were
changed to initialize it, so arptables has this set to NULL.
This isn't a problem for normal arptables because no existing
arptables target has a checkentry function that makes use of par->net.
However, direct users of the setsockopt interface can provide any
target they want as long as its registered for ARP or UNPSEC protocols.
syzkaller managed to send a semi-valid arptables rule for RATEEST target
which is enough to trigger NULL deref:
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
RIP: xt_rateest_tg_checkentry+0x11d/0xb40 net/netfilter/xt_RATEEST.c:109
[..]
xt_check_target+0x283/0x690 net/netfilter/x_tables.c:1019
check_target net/ipv4/netfilter/arp_tables.c:399 [inline]
find_check_entry net/ipv4/netfilter/arp_tables.c:422 [inline]
translate_table+0x1005/0x1d70 net/ipv4/netfilter/arp_tables.c:572
do_replace net/ipv4/netfilter/arp_tables.c:977 [inline]
do_arpt_set_ctl+0x310/0x640 net/ipv4/netfilter/arp_tables.c:1456
Fixes: add67461240c1d ("netfilter: add struct net * to target parameters")
Reported-by: syzbot+d7358a458d8a81aee898@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2548288b4fb059b2da9ceada172ef763077e8a59 upstream.
It turns out that even though endpoints with a maxpacket length of 0
aren't useful for data transfer, the descriptors do serve other
purposes. In particular, skipping them will also skip over other
class-specific descriptors for classes such as UVC. This unexpected
side effect has caused some UVC cameras to stop working.
In addition, the USB spec requires that when isochronous endpoint
descriptors are present in an interface's altsetting 0 (which is true
on some devices), the maxpacket size _must_ be set to 0. Warning
about such things seems like a bad idea.
This patch updates an earlier commit which would log a warning and
skip these endpoint descriptors. Now we only log a warning, and we
don't even do that for isochronous endpoints in altsetting 0.
We don't need to worry about preventing endpoints with maxpacket = 0
from ever being used for data transfers; usb_submit_urb() already
checks for this.
Reported-and-tested-by: Roger Whittaker <Roger.Whittaker@suse.com>
Fixes: d482c7bb0541 ("USB: Skip endpoints with 0 maxpacket length")
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://marc.info/?l=linux-usb&m=157790377329882&w=2
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2001061040270.1514-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2cdd07488e666aa93a49a3fc9c9b1299e27ef3c upstream.
In rtl8xxxu_submit_int_urb if usb_submit_urb fails the allocated urb
should be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e62395da2bd5166d7c9e14cbc7503b256a34cb0 upstream.
In bfad_im_get_stats if bfa_port_get_stats fails, allocated memory needs to
be released.
Link: https://lore.kernel.org/r/20190910234417.22151-1-navid.emamdoost@gmail.com
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db8fd2cde93227e566a412cf53173ffa227998bc upstream.
In mwifiex_pcie_alloc_cmdrsp_buf, a new skb is allocated which should be
released if mwifiex_map_pci_memory() fails. The release is added.
Fixes: fc3314609047 ("mwifiex: use pci_alloc/free_consistent APIs for PCIe")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Acked-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d94a4a8373bf5f45cf5f939e88b8354dbf2311b upstream.
mwifiex_process_country_ie() function parse elements of bss
descriptor in beacon packet. When processing WLAN_EID_COUNTRY
element, there is no upper limit check for country_ie_len before
calling memcpy. The destination buffer domain_info->triplet is an
array of length MWIFIEX_MAX_TRIPLET_802_11D(83). The remote
attacker can build a fake AP with the same ssid as real AP, and
send malicous beacon packet with long WLAN_EID_COUNTRY elemen
(country_ie_len > 83). Attacker can force STA connect to fake AP
on a different channel. When the victim STA connects to fake AP,
will trigger the heap buffer overflow. Fix this by checking for
length and if found invalid, don not connect to the AP.
This fix addresses CVE-2019-14895.
Reported-by: huangwen <huangwenabc@gmail.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
